지속저인 산업발전은 화석 연료사용과 에너지 사용을 증가시켰으며, 각 국가별 온실가스 배출은 증가하고 있는 실정이다. 국제사회는 지구 온난화 방지를 위해 1997년 교토 의정서를 채택하였고, 이산화탄소(CO2) 순 배출량 0을 목표로 하여 자체적으로 온실가스 배출 목표를 정하고 실천하고자 2015년 '파리기후변화협정'을 채택하였다. 우리나라는 2015년 '파리기후변화협정' 체결 후 2030년까지 2017년 총 배출량 대비 24.4 % 감축을 목표로 설정하였다.(외교부, 2020) 국내 사회 각 분야에서는 온실가스 감축을 위해 노력하고 있으며, 도로분야에서는 온실가스 저감을 위한 환경친화형 도로 설계와 시 공기술 개발을 위한 연구들이 검토되고 있다. 그 중 가열 아스팔트 혼합물 제조 시 사용되는 기존의 연료(중유, 벙커씨유, 정제유 등) 를 상대적으로 탄소배출량이 적은 연료(LPG, LNG)로 전환하거나, 플랜트 생산온도를 낮추어 사용되는 연료를 저감하는 방법 등 다양 한 연구를 진행하고 있다. 따라서 본 연구에서는 일반 가열 아스팔트 혼합물보다 약 50℃ 낮은 상태에서 생산할 수 있게 도와주는 탄소저감형 첨가제를 적용 한 저가열 아스팔트의 특성을 파악하고자 하였다. 기본 물성시험으로는 연화점, 신도, 회전점도를 시험하였으며, 공용성 등급 시험을 통하여 PG 등급을 확인하였다. 또한 기존에 상용화된 제품과 차이를 보기 위해, 첨가제가 투입되지 않은 일반 아스팔트와 중온 첨가 제 2종(고상형, 액상형)이 적용된 중온 아스팔트도 동일한 시험을 진행하였고, 저가열 아스팔트와 비교·분석 하였다.

인도네시아는 전 세계에서 여섯 번째로 많은 탄소 배출국으로, 2023년 기준 약 729 MtCO₂를 배출하며 아세안 국가 중 가장 높은 배출량을 기록하고 있다(Global Carbon Atlas). 이러한 탄소 배출은 주로 화석연료 사용과 산림 벌채로 인해 발생한다. 인도네시아 정부 는 파리기후협정에 따라 2030년까지 온실가스 배출을 29% 감축하는 목표를 설정했으며, 이를 달성하기 위해 다양한 저탄소 기술 도입 이 필수적이다. 특히, 도로 건설 분야에서는 탄소 저감과 시공 효율성을 동시에 향상시킬 수 있는 중온 아스팔트(Warm Mix Asphalt) 기술이 중요한 역할을 한다. 본 연구에서는 인도네시아에 적합한 중온 아스팔트 기술의 적용 가능성을 평가하기 위해, 국내 골재와 중온첨가제를 사용하여 인도 네시아 현지 바인더(IN 6070, 침입도 60-70)와 국내 아스팔트 바인더(PG64-22, 침입도 60-80)를 각각 비교 분석하였다. 인도네시아 시방 기준에 따라 배합설계를 수행하였으며, 합성입도는 인도네시아 시방기준과 유사한 입도(WC-2)를 적용하였다. 또한 현지 바인더와 국내 바인더를 비교하여 성능 차이를 분석하고, 중온첨가제를 사용한 경우와 그렇지 않은 경우의 혼합물 특성도 평가하였다. 아스팔트 바인더 시험 결과, 인도네시아 바인더는 국내 바인더와 유사하였으며, 중온첨가제를 적용한 경우 점도가 모두 낮아지는 경 향을 보였다. 혼합물 시험 결과(국내 골재 사용) 두 바인더 모두 유사한 성능을 나타냈으며, 중온첨가제를 사용한 경우 가열 아스팔트 대비 약 30℃ 낮은 온도에서도 공극률이 유사하였고, 품질 기준을 모두 만족하였다. 향후 인도네시아의 골재와 바인더에 국내 중온첨 가제를 적용한 시험 결과가 본 연구와 유사하게 나타난다면, 국내 중온첨가제를 인도네시아 도로 건설에 적용할 수 있을 것으로 판단 된다.

PURPOSES : This study analyzed the amount of fuel consumption and atmospheric emissions by type of asphalt concrete mixtures. METHODS : Asphalt concrete mixture was produced directly at the plant, fuel consumption was measured compared to daily production, and atmospheric emissions emitted during the production process were measured. Hot and warm asphalt mixtures were produced, and analyses were conducted according to weather conditions and production volume. RESULTS : The fuel use per ton was confirmed to reduce energy by approximately 23.5% in WMA compared to HMA due to differences in the production temperature during the production of asphalt mixtures. Additionally, HMA production yielded 1.6 times higher atmospheric emissions for CO2 and 3.8 times higher for NOx than that for WMA, indicating that CO2 and NOx emissions tended to increase as fuel consumption increased. CONCLUSIONS : When producing asphalt mixtures, the production temperature, production volume, atmospheric conditions, and site conditions have a significant impact on fuel usage and atmospheric emissions.

PURPOSES : There has been increasing interest in South Korea on warm-mix asphalt (WMA) and cold-mix asphalt (CMA) technologies that allow production of asphalt pavement mixtures at comparatively lower temperatures than those of hot-mix asphalt (HMA) for use in pavement engineering. This study aims to evaluate the feasibility of replacing HMA pavement with WMA pavement with the goal of reducing CO2 emissions associated with asphalt production for road construction. METHODS : Changes in the dynamic modulus characteristics of WMA and HMA according to short-term and long-term aging were evaluated. In addition, the effects of water damage were evaluated for short- and long-term aging stages. RESULTS : For WMA, in the process of mixing and short-term aging, early-age dynamic modulus decreased owing to low temperature and reduced short-term aging (STA) time. This could result in early damage to the asphalt pavement depending on the applied traffic load and environmental load. CONCLUSIONS : Mastercurves of the dynamic modulus were used for comparative analysis of WMA and HMA. Compared to the dynamic modulus after STA of HMA, the estimated aging time determined by experiments for WMA to achieve the required stiffness was more than 48 hours, which is equiva-lent to approximately 4 to 5 years real service life when converted. It is considered that further studies are needed for performance optimization to achieve early-age performance of the asphalt mixes.

PURPOSES : This study was conducted to evaluate the physical properties of the RAP 50 asphalt mixture containing polymer modified rejuvenator and warm-mix additive to improve the recycling rate of RAP and reduce CO2 emission. METHODS : Mix design of Polymer Modified Warm-mix Asphalt Mixture(RAP 50), and Hot Mix Asphalt Mixture(RAP 30) were produced and the properties of asphalt mixture such as Marshall Stability, ITS, Deformation Strength, TSR, and Dynamic Stability were compared between the two asphalt mixtures. RESULTS : The RAP 50 asphalt mixture showed superior or similar performances compared to the RAP 30 asphalt mixture in all the tests conducted. The results of the Marshall stability and dynamic stability in particular were 13,045N and 3,826 pass/mm, which were 11.37% and 76.7% greater than the RAP 30 asphalt mixture, which indicated that high plastic deformation resistance may be expected. CONCLUSIONS : The results obtained from laboratory tests on the two types of mixtures indicated that the use of polymer modified rejuvenator and warm-mix additive not only allows to increase the proportion of RAP but also improves its properties under lower temperature condition than RAP 30 asphalt mixture. Additionally, it was confirmed that plastic deformation resistance was high and moisture resistance and crack resistance were improved for a RAP 50 asphalt mixture.

PURPOSES : Owing to industrial development, the occurrence of continuous environmental damage such as abnormal weather is accelerating because of a rapid increase in carbon emissions. Therefore, various efforts are expended worldwide to realize a low-carbon ecofriendly society. In the construction industry, various efforts have been realized to reduce environmental pollution such as greenhouse gas emissions, for example by introducing eco-friendly materials and reducing industrial waste. In this study, an asphalt pavement technology that can reduce production and construction temperatures by more than 60 °C is developed to reduce the amount of carbon generated in the asphalt industry. METHODS : The performance of a half-warm asphalt binder developed using thermoplastic elastomers and low-temperature additives was assessed. In addition, the change in the quality of a mixture due to the use of the half-warm asphalt binder was evaluated. RESULTS : As the amount of thermoplastic elastomer used increases, the performance grade of the asphalt binder increases as well. When 3% or more of the elastomer is incorporated, the target performance grade of the asphalt binder is satisfied. In addition, by incorporating the thermoplastic elastomer and a low-temperature additive, the overall moisture and rutting resistance increased even at relatively low production and compaction temperatures. CONCLUSIONS : Additional measures to stabilize quality and improve economic feasibility will present a new paradigm for investigations into eco-friendly asphalt concrete pavements.

PURPOSES : The purpose of this study was to reduce greenhouse gases and prevent potholes on roads by evaluating the performances of hot and warm mixed asphalt mixtures. METHODS : Quality tests were conducted using an appropriate aggregate ratio of the asphalt mixture. The tests for comparing the warm mixed asphalt mixture are the indirect tensile strength and toughness, Marshall stability and flow, tensile strength ratio, and dynamic immersion test. A performance evaluation was conducted using a mixture that satisfied the quality test results. A performance evaluation test was also conducted using the dynamic modulus and Hamburg wheel tracking test. To analyze the performance based on the amine content, the performance was compared with that of a hot mixed asphalt mixture. RESULTS : All tests for the mixture results satisfied the standard values. The optimal amine content was analyzed through the high and low frequencies of the dynamic modulus test results and stripping inflection point with the final rut depth of the Hamburg wheel tracking test. The dynamic modulus test results demonstrated better crack resistance and plastic deformation when a high amine content ratio was used. The Hamburg wheel-tracking test showed water resistance and plastic deformation resistance. The test results of the Hamburg wheel tracking indicated better deformation resistance and water resistance when a high amine content ratio was used. CONCLUSIONS : The plastic deformation and crack resistance increased with an increase in amine content. Analysis of the comprehensive test revealed that the optimal amine content was between that of additives B(50%) and C(65%). Tests with a granular amine content are planned to confirm the specific components. Also planned are a simplified viscoelastic continuum damage test and a semicircular bending test to evaluate the performance better.

PURPOSES : This study compared the performance evaluation of a hot mix asphalt (HMA) and asphalt mixture of a warm-antistrip agent. METHODS : A mix design applying Korean standards was conducted to evaluate the performance evaluation. Thereafter, the quality standard evaluation of the asphalt mixture produced was conducted, and if all quality standards were satisfied, a performance evaluation was conducted. Types of performance evaluation included the Hamburg wheel tracking test and dynamic modulus test. RESULTS : As a result of the Hamburg wheel tracking test, the asphalt mixture with a warm-antistrip agent obtained a lower sedimentation value at 10000 times and 20000 times. This result is considered to have higher plastic deformation resistance of the asphalt mixture with a Warm-antistrip agent than HMA. The U.S. Department of Transportation stipulates that plastic deformation resistance is excellent if the asphalt mixture does not exceed 20,000 times the precipitate of 20 mm. Therefore, we confirmed that the plastic deformation resistance of the asphalt mixture with a warm-antistrip agent was excellent. Additionally, the master curve was analyzed by synthesizing the results of the dynamic modulus test. When analyzing the low load cycle at the bottom left of the master curve, the dynamic modulus value of the master curve was higher in the asphalt mixture with a warm-antistrip agent than in the HMA. In addition, when analyzing the high load cycle part, the dynamic modulus of the HMA was measured to be higher than that of the asphalt mixture with a warm-antistrip agent. Accordingly, the resistance to fatigue cracking of the asphalt mixture with a warm-antistrip agent was considered superior to that of the HMA. CONCLUSIONS : As a result, we confirmed that the asphalt mixture with a warm-antistrip agent that satisfies the Korean quality standards had better plastic deformation and fatigue resistance for all performance evaluation tests conducted in this study than the HMA. However, since the Hamburg wheel tracking test did not significantly differ in the amount of sedimentation in the performance evaluation tests and the mixture using one additive was compared with HMA, studies on the effects of various additives containing warm-antistrip agents are required.

PURPOSES : The purpose of this study is to evaluate an asphalt mixture via field application to utilize basalt aggregates produced on Jeju Island for a warm mix asphalt (WMA). METHODS : Using commercially available WMA additives, an indoor experiment is conducted on low- and high-void aggregates among basalt aggregates on Jeju Island. The physical properties of the WMA mixture are evaluated using one solid type and two liquid types of WMA additive. To evaluate the applicability of the WMA additives, air void, saturation, aggregate void, Marshall stability, flow number, indirect tensile strength, and toughness tests are performed. For the field application of WMA using basalt aggregates, three types of pavements (HMA, WMA-Solid, and WMA-liquid) are constructed. When applying the pavements in the field, an anti-stripping agent is incorporated to improve the water resistance while considering the characteristics of the basalt aggregate. Samples are acquired via plant and field coring to evaluate the properties of the materials applied in the field. RESULTS : In the indoor test for analyzing the applicability of the commercialized WMA additives to basalt aggregates, all tests except the indirect tensile strength test show results that satisfy the standards. All test results, including that from the indirect tensile strength test, satisfy the standard values in the test that uses the sample material obtained from the plant. Similarly, in the test with field cores, all test results satisfy the standard values. Therefore, the experimental value in the field application is generally higher than the test value in the indoor experiment. It is inferred that this is due to the difference between the basalt aggregates used in the indoor and field experiments, as well as the addition of the anti-stripping agent. CONCLUSIONS : Basalt aggregates produced on Jeju Island can be used for WMA pavements, as demonstrated via indoor experiments and field applications. However, owing to the characteristics of basalt aggregates, a method for improving water resistance should be considered, and tests to determine the indirect tensile strength should be performed using various basalt aggregates. In addition, because various basalt aggregates exist owing to the diverse geology characteristics of Jeju Island, they should be evaluated via more experiments and field applications.