In this article, to solve the problems about obsolescence of parts and unable to driving turret when internal components are failure, the DC-DC boost converter in the gun/turret drive system of mobile weapon was improved. The power converting circuit in converter is changed by applying the latest components, and the control circuit is changed from analog to digital. Also, the power converting circuits were modularized in three parallel so that it could be driven even when some components failed. The improved DC-DC boost converter secured stability such as converting to voltage in a linear manner in the entire section from the start of boosting to the end. Also, through the modular configuration, turret driving system can operates when some components failed.
OWEC(Overtopping Wave Energy Converter)는 월파된 파도를 이용한 파력발전시스템이라한다. OWEC의 성능 및 안전성은 파고, 주기 등 파도의 특성에 의해 영향을 받는다. 따라서 해역 특성에 따른 OWEC의 최적 형상과 구조안전성에 관한 연구가 필요하다. 본 연구 에서는 울릉읍 연안 해양 환경 데이터를 이용하였으며, SPH(Smoothed Particle Hydrodynamics) 입자법 해석을 통해 기존 케이슨 하부 구조에 변화를 준 모델 4개를 비교하여 월파 효율을 분석하였다. 그 결과, 하부 구조의 변경 및 경량화가 가능함을 확인하였다. 최적화 해석을 통 해 설계 하중에 내하력을 가지는 하부 구조인 새로운 트러스형 구조를 제안하였다. 이후 부재 직경 및 두께를 설계변수로 하는 사례 연구 를 통해 허용응력조건 하에서 구조 안전성의 확보를 확인하였다. 주기적인 파랑 하중을 받기 때문에 제안하는 구조의 고유 진동수와 해 당 해역의 파주기를 비교하였으며, 1년 재현 주기의 파랑을 하중으로 한 조화응답해석을 수행하였다. 제안하는 하부 구조는 동일 가진력 에서 기존 설계 대비 응답의 크기가 감소하였으며, 기존 대비 32% 이상의 중량 절감을 수행하였다.
We have observed a phenomenon where the internal X capacitors of the input EMI filter experienced damage during operation. To solve the problem, we have analyzed the malfunction by identifying the characteristics and operating principles of EMI filter. Based on this analysis, we have derived improvement strategies and validated them through experiments. This paper help some people prevent the similar problem when developing the similar equipment and solve the similar problem of the similar equipment.
The Alkali-Metal Thermal to Electric Converter (AMTEC) can be used as a next-generation power generation technology related with a large thermal energy storage. In particular, this technology is expected for the higher efficiency by a cascade power generation with the thermoelectric generator(TEG), and the temperature distribution becomes a very important design parameter in this case. In this study, the temperature distribution of the AMTEC unit was analyzed through CFD analysis, and design points were discussed based on the results.
월파된 파도를 이용한 파력발전시스템을 월파수류형 파력발전기 OWEC(Overtopping Wave Energy Converter)라고 한다. OWEC의 성능은 발전 시스템은 특성상 파도의 파고와 주기의 영향을 받는다. 파도는 해양에 따라 파고, 주기, 파도 방향 등의 특성이 다르고 이러 한 파도의 다양한 특성 때문에 OWEC는 안정적인 전력을 생산하기 어렵다. 따라서 각 바다의 특성에 따른 OWEC의 적절한 형상에 관한 연구가 필요하다. 본 연구에서는 SPH(Smoothed Particle Hydrodynamics) 입자법을 사용하여 OWEC의 램프 설계가 hydraulic efficiency에 미치 는 영향을 확인했다. 총 10개의 모델을 설계하였으며, 선택된 매개변수에 따라 램프의 설계 파라미터를 선택하고 사면의 형상을 변경하여 시뮬레이션을 수행하였다. 해석 결과로부터 구한 유량을 기초로 hydraulic efficiency를 산출하였다. 계산된 hydraulic efficiency를 바탕으로 각 변수가 사면의 형상에 따른 월파 성능에 미치는 영향을 확인하였다. 본 연구에서는 특정 해역에 따른 OWEC 램프의 적절한 형상에 대한 방향을 제시하였다.
LDV(laser Doppler velocimetry) measurements were conducted at a total of four planes at 0.4 speed ratio. The speed ratio of 0.4 is 1600rpm of impeller and 633rpm of turbine speed. Even at the speed ratio 0.4, fluid flow at the gap region between the impeller and turbine and impeller exit was leaving the impeller and flowing up behind the turbine, and flows were affected by the turbine blade as it passed, negatively effecting converter efficiency. In the gap region, fluctuations make a clear sinusoidal trend unclear. The rise and fall of the flow rates in a broad sense, indicate a dependency based on the passage of the turbine blade in front of the impeller passage exit but a sinusoidal trend is not evident from this data.
LDV(laser Doppler velocimetry) measurements were conducted on the exit region of the impeller passage and the gap between the impeller and turbine blades under 0.8 speed ratio. The 0.8 speed ratio has an impeller speed of 2000rpm and a turbine speed of 1600rpm. A periodic variation of the mass flow rate is present in many of the measurements made. The frequency of this variation is the same as the frequency of the turbine blades passing the impeller passage exit. It is found that the instantaneous position of the turbine had effect on fluid flow inside the impeller passage and gap region. This study would aid in the construction of higher accuracy CFD models of this complex turbomachinery device.
본 연구는 전기자동차 충전시스템에서 전력변환장치의 경량화를 위한 최적화 분석프로세스에 대한 내용을 서술하였다. 최적화 설계는 재료 물성치에 대한 설계민감도와 수학적 최적화를 결합하여 주어진 재료량 제한조건 하에 최적의 재료분포를 찾는 설계기법으로 위상의 고정화, 자유도가 묶이는 문제 등을 해결할 수 있는 위상 최적화방법을 사용하였으며, 위상 최적화 방법 중 비교적 수식화가 간단하고 수렴성이 좋은 SIMP법(solid isotropic material with penalization)에 의해 경량화 설계를 수행하였다. 경량화 설계는 3단계의 절차로 구성하였으며, 첫 번째 단계로 전력변환장치의 기본 설계에 대한 유한요소모델을 구성하고, 하중에 대한 정적해석을 수행하였다. 두 번째 단계로 정적해석 결과에 대해 등방성 재료의 강성계수를 적용한 밀도법을 이용하여 위상 최적화를 수행하여 경량화를 위한 최적 형상을 도출하였다. 세 번째 단계로 최적 형상에 대해 차량 탑재 부품의 충격시험기준에 만족하는 반정현파 펄스형태 충격하중을 인가하여 충격해석을 수행하였다. 위상 최적화단계에서 사용 환경조건으로 설계영역 정의는 마운팅 브래킷 영역으로 제한하였으며, 마운팅 브래킷의 설계 최적화를 통해 최종적으로 기본설계대비 20%이상의 경량화가 가능한 설계기술을 확보하였다.
본 논문은 직류전동기 속도제어를 위해 매트릭스 컨버터의 적용 가능성을 제안한다. 매트릭스 컨버터는 크게 직접 매트릭스 컨버터와 간접 매트릭스 컨버터로 나뉘는데 본 논문에서는 다양한 출력 단을 구성할 수 있어 향후 많은 활용이 예상되는 간접 매트릭스 컨버터를 이용하였다. 제안한 방식은 기존의 방식보다 입력 전류의 파형을 개선하고, 부피가 크고 비용이 많이 들며 수명단축의 원인이 되는 에너지 저장 요소를 가지지 않는 이점이 있다. 시뮬레이션을 통하여 기존 방식과 본 논문에서 제안하는 방식의 특징을 비교 분석하여 제안한 방식의 유효성을 입증하였다. 속도제어, 토크제어, 부하전류제어에서는 유사한 성능을 보이며, 입력전류는 정류단의 스위치를 직접 제어함으로써 정현파와 유사하게 제어되기 때문에 고조파가 크게 감소되었다.
The influencing factors to remove phosphate were evaluated by converter slag (CS). Experiments were performed by batch tests using different CS sizes and column test. Solutions were prepared at the different pH and concentrations. The maximum removal efficiency was obtained over 98% with the finest particle size, CSa within 2 hours in batch tests. The removal efficiency was increased in the order of decreasing size with same amount of CS for any pH of solutions. The adsorption data were well fitted to Freundlich isotherm. From the column experiment, the specific factors were revealed that the breakthrough removal capacity (BRC) xb/mcs, was decreased by increasing the influent concentration. The breakthrough time, tb was lasted shorter as increasing the influent concentration. The pH drop simultaneously led to lower BRC drop during the experimental hours. The relation between the breakthrough time and the BRC to influent concentration was shown in the logarithmic decrease. Results suggested that the large surface area of CS possessed a great potential for adsorptive phosphate removal. Consequently particle size and initial concentration played the major influencing factors in phosphate removal by converter slag.
The general auto transmission uses the torque converter that has a good vibration damping force by launching performance and damping effect as power transfer unit. The vehicle equipped with auto transmission uses Lock up clutch system to improve the fuel efficiency. The Lock up clutch system is the major factor of the devices that increase the torque from engine to transmission in specific condition and also consist of the damper springs to transfer the torque stably. Damper spring controls the vibration of power transfer units and improve the impression of riding and durability, by being damping function on change torque from engine. In addition, not only the appearance and performance, but also these sensitive qualities as like vibration and noise can also be main factor to buy a car. Recently, in order to absorb the low vibration caused by vehicle structure vibration, the Low-stiffness damper has been on the rise. The damper spring should be considered and designed, considering the engine characteristic and direct connect of lock up clutch due to the stiffness of the spring and hysteresis has a major effects to the damper characteristic. This study can be used for analyzing the major factors to effect the NVH characteristic by evaluating the damper’s hysteresis according to change of spring stiffness.
Because industrial Vehicles drive and work under heavy load condition, the gear ratio of transmission and the stall torque ratio of torque converter is high. Recently, to reduce the cost of vehicle, many people have interest in applying multi-phase torque converter to vehicle and reducing the gear step. In this study, the target performance of vehicle is analyzed and the performance matching of multi-phase torque converter is studied to equip torque converter to heavy duty folk lift vehicle.
Occupational fatal injury rate per 10,000 population of Korea is still higher among the OECD member countries. To prevent fatal injuries, the causes of accidents including human error should be analyzed and then appropriate countermeasures should be established. There was an severe converter furnace accident resulting in five people death by chocking in 2013. Although the accident type of the furnace accident was suffocation, many safety problems were included before reaching the death of suffocation. If the safety problems are reviewed throughly, the alternative measures based on the review would be very useful in preventing similar accidents. In this study, we investigated the converter furnace accident by using human error analysis and accident scenario analysis. As a result, it was found that the accident was caused by some human errors, inappropriate task sequence and lack of control in coordinating work by several subordinating companies. From the review of this case, the followings are suggested: First, systematic human error analysis should be included in the investigation of fatal injury accidents. Second, multi man-machine accident scenario analyis is useful in most of coordinating work. Third, the more provision of information on system state will lessen human errors. Fourth, the coordinating control in safety should be performed in the work conducting by several different companies.
The excessive concentration of phosphorus in the river and reservoir is a deteriorating factor for the eutrophication. The converter slag was used to remove the phosphate from the synthetic wastewater. Influencing factors were studied to remove soluble orthophosphate with the different particle sizes through the batch and the column experiments by continuous flow. Freundlich and Langmuir adsorption isotherm constants were obtained from batch experiments with PSA and PSB. Freundlich isotherm was fitted better than Langmuir isotherm. Regression coefficient of Freundlich isotherm was 0.95 for PSA and 0.92 for PSB, respectively. The adsorption kinetics from the batch experiment were revealed that bigger size of convert slag, PSA can be applied for the higher than 3.5 mg/L of phosphate concentration. The pilot plant of continuous flow was applied in order to evaluate the pH variation, breakthrough points and breakthrough adsorption capacity of phosphate. The variation of pH was decreased through the experimental hours. The breakthrough time was 1,432 and 312 hours to 10 mg/L and 50 mg/L for the influent concentration, respectively. The breakthrough adsorption capacity was 3.54 g/kg for 10 mg/L, and 1.72 g/kg for 50 mg/L as influent phosphate concentration.
The paper describes variable circuits technique the enable of differential circuit of charge pump. It is able to pump an input voltage of 2V to measure several output voltage through several clock signal with each pumping capacitor of 1 pF and smoothing capacitor of 1 pF at the output. From the simulation result, it is evident that charge pump circuits offer verity high voltage pumping gain. The circuits which are implemented in this paper is simulated with LT SPICE tool of computer.