In this study, NASICON-type Li1+XGaXTi2-X(PO4)3 (x = 0.1, 0.3 and 0.4) solid-state electrolytes for all-solid-state batteries were synthesized through the sol-gel method. In addition, the influence on the ion conductivity of solid-state electrolytes when partially substituted for Ti4+ (0.61Å) site to Ga3+ (0.62Å) of trivalent cations was investigated. The obtained precursor was heat treated at 450 °C, and a single crystalline phase of Li1+XGaXTi2-X(PO4)3 systems was obtained at a calcination temperature above 650 °C. Additionally, the calcinated powders were pelletized and sintered at temperatures from 800 °C to 1,000 °C at 100 °C intervals. The synthesized powder and sintered bodies of Li1+XGaXTi2-X(PO4)3 were characterized using TGDTA, XRD, XPS and FE-SEM. The ionic conduction properties as solid-state electrolytes were investigated by AC impedance. As a result, Li1+XGaXTi2-X(PO4)3 was successfully produced in all cases. However, a GaPO4 impurity was formed due to the high sintering temperatures and high Ga content. The crystallinity of Li1+XGaXTi2-X(PO4)3 increased with the sintering temperature as evidenced by FE-SEM observations, which demonstrated that the edges of the larger cube-shaped grains become sharper with increases in the sintering temperature. In samples with high sintering temperatures at 1,000 °C and high Ga content above 0.3, coarsening of grains occurred. This resulted in the formation of many grain boundaries, leading to low sinterability. These two factors, the impurity and grain boundary, have an enormous impact on the properties of Li1+XGaXTi2-X(PO4)3. The Li1.3Ga0.3 Ti1.7(PO4)3 pellet sintered at 900 °C was denser than those sintered at other conditions, showing the highest total ion conductivity of 7.66 × 10-5 S/cm at room temperature. The total activation energy of Li-ion transport for the Li1.3Ga0.3Ti1.7(PO4)3 solidstate electrolyte was estimated to be as low as 0.36 eV. Although the Li1+XGaXTi2-X(PO4)3 sintered at 1,000 °C had a relatively high apparent density, it had less total ionic conductivity due to an increase in the grain-boundary resistance with coarse grains.

The challenge of incorporating photothermal conversion function into chitosan (CS) hybrid fibers lies in balancing functionality and mechanical properties. In this study, we successfully prepared a chitosan/graphene oxide/gelatin (CS/GA/GO) hybrid fiber using the wet spinning process, achieving improved mechanical properties and efficient photothermal conversion capabilities. When compared with pure CS fiber with a breaking strength of 1.07 cN/dtex, the breaking strength of the CS/ GA composite fiber increased by 46.73%, while the CS/GA/GO hybrid fiber showed an even greater increase of 85.98%. In addition, the introduction of gelatin (GA) led to secondary scattering of near-infrared light, enhancing the photothermal conversion efficiency. As a result, the CS/GA/GO hybrid fiber exhibited a faster temperature rise rate and higher maximum temperatures (94.3 °C, 103.0 °C, and 111.3 °C) as compared to the CS/GO hybrid fiber. The successful incorporation of GA not only improved the mechanical properties but also enhanced the photothermal performance of the hybrid fiber.

β-Ga2O3 has become the focus of considerable attention as an ultra-wide bandgap semiconductor following the successful development of bulk single crystals using the melt growth method. Accordingly, homoepitaxy studies, where the interface between the substrate and the epilayer is not problematic, have become mainstream and many results have been published. However, because the cost of homo-substrates is high, research is still mainly at the laboratory level and has not yet been scaled up to commercialization. To overcome this problem, many researchers are trying to grow high quality Ga2O3 epilayers on hetero-substrates. We used diluted SiH4 gas to control the doping concentration during the heteroepitaxial growth of β-Ga2O3 on c-plane sapphire using metal organic chemical vapor deposition (MOCVD). Despite the high level of defect density inside the grown β-Ga2O3 epilayer due to the aggregation of random rotated domains, the carrier concentration could be controlled from 1 × 1019 to 1 × 1016 cm-3 by diluting the SiH4 gas concentration. This study indicates that β-Ga2O3 hetero-epitaxy has similar potential to homo-epitaxy and is expected to accelerate the commercialization of β-Ga2O3 applications with the advantage of low substrate cost.

Amorphous In-Ga-Zn-O (a-IGZO) thin film transistors (TFTs) with a coplanar structure were fabricated to investigate the feasibility of their potential application in large size organic light emitting diodes (OLEDs). Drain currents, used as functions of the gate voltages for the TFTs, showed the output currents had slight differences in the saturation region, just as the output currents of the etch stopper TFTs did. The maximum difference in the threshold voltages of the In-Ga-Zn-O (a-IGZO) TFTs was as small as approximately 0.57 V. After the application of a positive bias voltage stress for 50,000 s, the values of the threshold voltage of the coplanar structure TFTs were only slightly shifted, by 0.18 V, indicative of their stability. The coplanar structure TFTs were embedded in OLEDs and exhibited a maximum luminance as large as 500 nits, and their color gamut satisfied 99 % of the digital cinema initiatives, confirming their suitability for large size and high resolution OLEDs. Further, the image density of large-size OLEDs embedded with the coplanar structure TFTs was significantly enhanced compared with OLEDs embedded with conventional TFTs.

In this study, to control the heading angle of a ship, which is constantly subjected to various internal and external disturbances during the voyage, an LADRC (linear active disturbance rejection control) design that focuses more on improving the disturbance removal performance was proposed. The speed rate of change of the ship’s heading angle due to the turn of the rudder angle was selected as a significant factor, and the nonlinear model of the ship’s maneuvering equation, including the steering gear, was treated as a total disturbance. It is the similar process with an LADRC design for the first-order transfer function model. At this time, the gains of the controller included in LADRC and the gains of the extended state observer were tuned to RCGAs (real-coded genetic algorithms) to minimize the integral time-weighted absolute error as an evaluation function. The simulation was performed by applying the proposed GA-LADRC controller to the heading angle control of the Mariner class vessel. In particular, it was confirmed that the proposed controller satisfactorily maintains and follows the set course even when the disturbances such as nonlinearity, modelling error, uncertainty and noise of the measurement sensor are considered.

The (Ga1-xZnx)(N1-xOx) solid solution is attracting extensive attention for photocatalytic water splitting and wastewater treatment owing to its narrow and controllable band gap. To optimize the photocatalytic performance of the solid solution, the key points are to decrease its band gap and recombination rate. In this study, (Ga1-xZnx)(N1-xOx) nanofibers with various Zn fractions are prepared by electrospinning followed by calcination and nitridation. The effect of the composition and crystallinity of electrospun oxide nanofibers on the morphology and optical properties of the obtained solid-solution nanofibers are systematically investigated. The results show that the final shape of the (Ga1-xZnx) (N1-xOx) material is greatly affected by the crystallinity of the oxide nanofibers before nitridation. The photocatalytic properties of (Ga1-xZnx)(N1-xOx) with different Ga:Zn atomic ratios are investigated by studying the degradation of rhodamine B under visible light irradiation.

한국 땅나리와 섬말나리의 수요는 최근까지도 늘어났지만 종자 상태에서 개화에 이르기까지 확률은 낮은 편으로 자생지에서의 개체수는 해마다 감소하였다. 본 연구는 땅나리(Lilium callosum Siebold & Zucc.)와 섬말나리(L. hansonii Leichtlin ex D.D.T. Moore)의 대량증식을 도모하기 위하여 종자 발아에 유리한 주·야간 온도 조건과 적합한 GA3 농도를 알아보는 것을 목적으로 수행되었다. 땅나리 종자는 2017년 10월 24일 강원도 춘천히 둔산면 원창리(37°47’10.00”N, 127°44’31.00”E), 섬말나리 종자는 2017년 10월 2일 울릉도 울릉군 북면 나리 (37°31’27.06”N, 130°52’25.08”E)에서 채종하였다. 땅나리와 섬 말나리 종자들을 주·야간 15/5, 20/10, 25/15, 20/20°C의 환경 조절상에서 처리구 당 30립씩 3반복으로 치상하여 온도 처리 실험을 진행한 후, 발아율 결과가 가장 우세했던 온도 조건의 환경조절상에서 섬말나리 GA3 처리 실험을 추가로 진행하였다. 온도 처리 실험결과 땅나리는 20/20°C의 온도 조건에서 발아율이 95.0%로 가장 높았으며 평균발아소요일수 또한 10.1일로 가장 낮았다. 섬말나리는 20/20°C의 온도 조건에서 발아율이 78.8%로 가장 높았으며 평균발아소요일수 또한 40.1일로 가장 낮았다. 이를 토대로 20/20°C에서 실시한 섬말나리 GA3 처리 실험은 증류수를 대조구로하여 200, 400, 800mg･L-1의 농도로 상온에서 24시간 침지한 후 처리구 당 20립씩 3반복으로 치상하였다. 그 결과 대조구에서 81.6%로 가장 높은 발아율을 나타냈으며 평균발아소요일수는 200mg･L-1처리구에서 37.1일로 가장 낮았다. 이러한 실험 결과를 바탕으로 땅나리와 섬말나리의 주·야간 발아 최적 온도는 20/20°C이며 GA3 24 시간 처리는 섬말나리 종자 발아에 효과가 없는 것으로 판단 되었다.

ZnO thin films are of considerable interest because they can be customized by various coating technologies to have high electrical conductivity and high visible light transmittance. Therefore, ZnO thin films can be applied to various optoelectronic device applications such as transparent conducting thin films, solar cells and displays. In this study, ZnO rod and thin films are fabricated using aqueous chemical bath deposition (CBD), which is a low-cost method at low temperatures, and environmentally friendly. To investigate the structural, electrical and optical properties of ZnO for the presence of citrate ion, which can significantly affect crystal form of ZnO, various amounts of the citrate ion are added to the aqueous CBD ZnO reaction bath. As a result, ZnO crystals show a nanorod form without citrate, but a continuous thin film when citrate is above a certain concentration. In addition, as the citrate concentration increases, the electrical conductivity of the ZnO thin films increases, and is almost unchanged above a certain citrate concentration. Cu(In,Ga)Se2 (CIGS) solar cell substrates are used to evaluate whether aqueous CBD ZnO thin films can be applicable to real devices. The performance of aqueous CBD ZnO thin films shows performance similar to that of a sputter-deposited ZnO:Al thin film as top transparent electrodes of CIGS solar cells.

Silver nanowire (AgNW) networks have been adopted as a front electrode in Cu(In,Ga)Se2 (CIGS) thin film solar cells due to their low cost and compatibility with the solution process. When an AgNW network is applied to a CIGS thin film solar cell, reflection loss can increase because the CdS layer, with a relatively high refractive index (n ~ 2.5 at 550 nm), is exposed to air. To resolve the issue, we apply solution-processed ZnO nanorods to the AgNW network as an anti-reflective coating. To obtain high performance of the optical and electrical properties of the ZnO nanorod and AgNW network composite, we optimize the process parameters – the spin coating of AgNWs and the concentration of zinc nitrate and hexamethylene tetramine (HMT – to fabricate ZnO nanorods. We verify that 10 mM of zinc nitrate and HMT show the lowest reflectance and 10% cell efficiency increase when applied to CIGS thin film solar cells.

본 연구는 동남아시아에서 흔하게 발견되는 ‘나가 위의 붓다(Buddha on Nāga)’ 도상이 서사부조에서 아이콘으로 확립되는 과정을 살펴본 것이다. 나가 위의 붓다 도상은 붓다가 똬 리를 튼 뱀의 몸통 위에 앉은 채로 머리 뒤로는 뱀의 머리 7개를 광배처럼 갖고 있는 모습을 지칭한다. 이 도상은 붓다가 보드가야에서의 성도 후 선정에 들었을 때 거센 폭풍우가 몰아 치자 무찰린다(Muchalinda)라는 이름의 나가, 즉 뱀이 나타나 붓다의 몸을 자신의 몸으로 감싸고 붓다의 머리 위로 자신의 머리를 펼쳐 보호하였다는 불전고사에서 유래하였다. 나가 위의 붓다는 2~3세기 무렵 남인도에서 부조로 먼저 만들어졌다. 남인도에서 만들 어진 나가 위의 붓다 부조에서 가장 중요한 것은 문헌의 묘사와 달리 뱀이 붓다의 몸을 감고 있는 모습이 아니라 붓다가 뱀의 몸통 위에 앉은 것으로 만들어진 점이다. 이는 조각을 만드 는 데 있어 붓다라는 존재를 명시적으로 드러낼 수 있으며 불교도들에게 시각적으로 더 자연스럽게 여겨질 수 있는 방식을 택했기 때문이다. 나가 위의 붓다 도상은 7세기 보드가야에서 독립상으로도 만들어졌으며 전체적인 도상은 앞서 본 남인도 부조들과 동일하다. 일찍이 많은 불전고사들이 부조로 만들어졌지만 그 중에서도 이 도상이 독립상으로 만들어질 수 있었던 이유는 보드가야가 7세기에 이르러 성지로서 높은 명성과 인기를 얻었기 때문이다. 이로 인해 순례자들을 위한 더 많은 기념물이 만들어지게 되었고, 이곳에서 일어난 가장 중요한 사건인 성도와 더불어 나가 무찰린다 고사 역시 보드가야에서 일어난 주요 사건 중 하나로 주목을 받아 독립상으로 만들어질 수 있었다. 특히 나가 위의 붓다 도상은 인도에서 먼저 만들어졌지만 인도보다는 이웃 동남아에서 더 욱 큰 인기를 얻고 붓다의 대표적인 도상으로 자리 잡았다. 7~8세기 무렵의 드바라바티 미 술에서도 다양한 나가 위의 붓다 부조가 발견되며, 특히 10세기 이후 크메르 미술에서는 뱀의 모습이 일관된 형태로 고정되고 장엄도 더욱 정교해지기에 이른다. 이는 토지와 물을 관장하는 신인 뱀에 대한 오랜 신앙이 동남아에 있었기 때문이다. 즉 수호신인 뱀에 대한 토착 신앙이 불교와 습합되면서 붓다를 보호하는 뱀의 이야기가 동남아에서 특히 인기를 얻게 되어 나가 위의 붓다가 붓다를 나타내는 지배적인 도상으로 자리매김한 것이다.

Ranunculus asiaticus characterizes colorful and attractive flower shapes that are related with the ornamental value of bulbous plants. Improving ornamental value of bulbous flowers has been the general goal of floricultural market. Gibberellic acid (GA3) and benzyladenine (BA) play an important role in growth and developmental processes in floriculture. Combinational treatments of these two hormones have been used in floriculture to improve flower quality. We assessed the effects of combined GA3 and BA, as well as the individual effects of each hormone, on growth characteristics using soil drench application to eight R. asiaticus cultivars, ‘Giallo Millepetali’, ‘Bianco Millepetali’, ‘Arancio Millepetali’, ‘Rosa SC’, ‘Arancio Pratolino’, ‘Giallo Pratolino’, ‘Bianco Pratolino’, and ‘Rosa Ch Pratolino’. GA3 treatments increased plant height and first flower size of R. asiaticus cultivars. Moreover, about 5 to 9 days to flowering were averagely shortened by GA3 treatments compared to controls. On the other hand, the opposites, including first flower size and days to flowering, were observed for cultivars treated with BA, compared with controls. Treatments of GA3 + BA generally affected growth traits, such as plant height, flower size, and the timing of flowering on some R. asiaticus cultivars. In particular, about 5 to 6 days to flowering were reduced on average by Treatments of GA3 + BA. Our results showed positive growth effects, including plant height, days to flowering, first flower height, number of flowers from the application of individual and combined hormones to R. asiaticus cultivars and demonstrate a role for these hormones in future bulbous floriculture.

This paper seeks to present a multi-control method that can contribute to effective control of the production line with multiple bottleneck processes. The multi-control method is the production system that complements shortcomings of CONWIP and DBR, and it is designed to determine the raw material input according to the WIP level of two bottleneck processes and WIP level of total process. The effectiveness of the production system developed by applying the multi-control method was verified by the following three procedures. Raw material input conditions of the multi-control method are as follows. First, raw materials are go into the production line when the number of the total process WIP is lower than established number of WIP in total process and first process is idle. Second, raw materials are introduced when the number of WIP of two bottleneck processes is lower than the established number of WIP of each bottleneck process. Third, raw materials are introduced when the first process and in front of bottleneck process are idle even if the number of WIP in the total process is less than established number of WIP of the total process. The production line with two bottleneck processes was selected as the condition for production environment, and the production process modeling of CONWIP, DBR and multi-control production method was defined according to the production condition. And the optimum limited WIP level suitable for each system was obtained by applying a genetic algorithm to determine the total limited number of WIP of CONWIP, the limited number of WIP of DBR bottleneck process, the number of WIP in the total process of multi-control method and the limited number of WIP of bottleneck process. The limited number of WIP of CONWIP, DBR and multi-control method obtained by the genetic algorithm were applied to ARENA modeling, which is simulation software, and a simulation was conducted to derive result values on the basis of three criteria such as production volume, lead time and number of goods in-progress.

본 연구는 황소개구리의 성별 및 성숙도, 시기에 따른 먹이원 및 포식 습성을 확인하기 위해 2014년 4월부터 9월까지 경상남도 창녕군 가항늪에서 진행하였다. 황소개구리 먹이원은 위 절제술을 통해 위에서 직접 수집하였으며, 위 내용물을 종 수준까지 동정하였다. 연구결과, 황소개구리는 크고 무거운 개체일수록 많은 양의 먹이를 포식하는 것으로 나타났으나, 성별 및 성숙도에 따른 포식량은 통계적으로 유의한 차이를 보이지 않았다. 연구기간 동안 황소개구리의 먹이원은 곤충강(개체 수 평균 비율 65.5%)이 가장 높은 비중을 차지하였고, 그 다음으로는 갑각강(13.5%), 복족강(7.9%) 순으로 나타났다. 황소개구리는 곤충강의 물자라(Muljarus japonicus)를 가장 많이 포식한 것으로 확인되었으며, 박새(Parus major), 등줄쥐(Apodemus agrarius), 땃쥐(Crocidura lasiura) 등도 황소개구리의 먹이원으로 나타났다. 황소개구리는 습지생태계의 교란에 직접적인 영향을 미치며, 이러한 결과들은 환경부 생태교란 생물로 지정되어 있는 황소개구리가 습지생태계에 미치는 영향을 확인하는데 중요한 기초자료가 될 수 있을 것으로 기대된다.