메조포러스 공극구조를 갖는 광촉매 멤브레인은 다양한 환경기술에 적용될 수 있다. 본 연구에서는 TiO2 층을 형 성시킨 광촉매 반응기용 세라믹 멤브레인을 개발하고 이를 염색용액 처리에 적용하였다. 높은 공극률과 균질성을 지닌 TiO2 광촉매층을 그라프트 공중합체를 사용하여 제조하였다. 멤브레인은 광촉매 반응기와 멤브레인 여과를 결합시킨 하이브리드 광촉매 반응기에 성공적으로 적용하였다. 실험결과 정렬된 구조의 TiO2 층이 Al2O3 지지체에 형성되었다. TiO2 층 형성 후 제조된 세라믹 분리막의 순수 투과도는 형성된 광촉매 층 저항으로 감소하였다. 정렬된 구조의 TiO2 층은 UV 결합 시 5시간 안에 완벽한 염색용액 분해를 달성시킬 수 있었다. 광촉매 멤브레인의 염색용액 분해는 Langmuir-Hinshelwood 흡착 모델로 잘 설명할 수 있었다. 또한 TiO2 층이 고정화된 세라믹 멤브레인의 model Congo Red에 대한 1차 속도상수는 Al2O3 지지체 단독인 경우에 비해 약 6배 정도 큰 값을 나타내었다(0.0081 vs. 0.0013 min-1).

Lithium ion battery are one of representative rechargeable batteries with high energy density, tiny memory effect, and low self-discharge and composed of anode, cathode, electrolyte, and membrane separator. The importance of membrane separator has been improved further as electric vehicle market increases rapidly. The conventional membrane separators are based on polyolefin (e.g., polyethylene and/or polypropylene). In case of lithium ion battery with a high capacity, polyolefin membrane separators are suffering from low thermal resistance and easy short-circuit formation leading to overheating. For these reasons, in this study, gel polymers are in-situ synthesized in electrolytes used as solvent, which are located in pores of polyolefin separators to obtain gel polymer electrolyte-polyolefin reinforced membranes.

Porous HAp with three-dimensional network channels was prepared in a polymer foam process using a in-situ formation. HAp/polyol with various HAp solid contents was formed with an addition of isocyanate. Under all conditions, the obtained porous HAp had pore sizes ranging 50 μm to 250 μm. The influence of the HAp content on the physical and mechanical properties of porous HAp scaffolds was investigated. As the solid content increased, the porosity of the porous HAp decreased from 79.3% to 77.9%. On the other hand, the compressive strength of the porous HAp increased from 0.7 MPa to 3.7 MPa. With a HAp solid content of 15 g, the obtained porous HAp had physical properties that were more suitable for scaffolds compared to other conditions.

nanoparticle was synthesized by the flame method, which was controlled by varying the ratio and flow rate of gas mixtures consisting of oxygen (oxidizer), methane (fuel) and nitrogen (carrier gas). The crystalline phases of nanoparticle depended strongly on the temperature distribution in the flame, whereas the morphology was not sensitive. We proved that the anatase phase formed without the phase transformation in the flame and the rutile phase generated through several phase transformations.