In this paper, the goal is to produce a target wheel that integrates the plate and CPS wheel among the components of the drive plate mounted on an automobile engine. We attempted to develop a manufacturing process technology for incremental forming of a target wheel with the desired thickness by rotating a disk-shaped thin plate material and deforming the plate using a forming device and tools. Incremental forming system was set up by establishing a forming process and designing and manufacturing the device and parts required for processing. It consists of a total of 4 stages of molding process, and the optimal roll design that can properly collect materials to prevent cracks or reverse steps at each stage is primarily important. After manufacturing the prototype, a material test was performed to confirm whether the mechanical properties of the deformed part were sufficient to make gear teeth.

블루베리 재배시 토양 유기물 공급원으로 쓰이고 있는 피트모스가 전량 수입에 의존하고 있어 국내에서 생산되는 소나무잎, 왕겨, 톱밥 등 유기물을 블루베리 정식 전 피트모스와 혼합처리 한 후 토양 pH 변화와 생육 및 과실 특성에 미치는 영향을 구명하고자 본 시험을 수행하였다. 시험품종은 2년생 북부 하이부시 블루베리 ‘Duke’ 품종이었고 묘목 정식 전 피트모스를 근권에 20L 단용으로 처리하는 방법과 피트모스(10L)와 소나무잎, 왕겨, 톱밥을 각각 10L씩 혼합 처리하는 방법으로 실시하였다. 유기물의 화학성 분석 결과 pH는 피트모스가 4.3으로 가장 낮았고 소나무잎은 4.8, 왕겨는 7.3, 톱밥은 5.7이었다. 정식 직후 유기물을 투여한 토양의 pH는 5.3~5.9 로 나타났고 피트모스단용, 피트모스+소나무잎 처리가 왕겨, 톱밥 혼합처리에 비해 낮았다. 정식 후 3년차 토양 pH는 4.2~4.5로 피트모스단용, 피트모스+소나무잎 처리에서 낮게 유지되었다. 유기물 조성에 따른 생육 시기 별 토양수분 함량은 피트모스+소나무잎>피트모스단용> 피트모스+톱밥>피트모스+왕겨 순으로 높게 나타났다. 생육은 피트모스 단용과 피트모스+소나무잎 처리에서 양호하였고 꽃눈수가 많아 초기 수량이 많았다. 당도는 피트모스 단용 처리에서 11.3 oBrix로 높았고 경도는 피트 모스+소나무잎 처리에서 증가되었으나 과실 품질에 있어 처리별 유의차는 없었다.

A thin Cu seed layer for electroplating has been employed for decades in the miniaturization and integration of printed circuit board (PCB), however many problems are still caused by the thin Cu seed layer, e.g., open circuit faults in PCB, dimple defects, low conductivity, and etc. Here, we studied the effect of heat treatment of the thin Cu seed layer on the deposition rate of electroplated Cu. We investigated the heat-treatment effect on the crystallite size, morphology, electrical properties, and electrodeposition thickness by X-ray diffraction (XRD), atomic force microscope (AFM), four point probe (FPP), and scanning electron microscope (SEM) measurements, respectively. The results showed that post heat treatment of the thin Cu seed layer could improve surface roughness as well as electrical conductivity. Moreover, the deposition rate of electroplated Cu was improved about 148% by heat treatment of the Cu seed layer, indicating that the enhanced electrical conductivity and surface roughness accelerated the formation of Cu nuclei during electroplating. We also confirmed that the electrodeposition rate in the via filling process was also accelerated by heat-treating the Cu seed layer.

The human ELAV(embryonic lethal abnormal vision)-like protein HuR stabilizes a certain group of cellul ar mHNAs that contain AU- rich elements in their 3’ - untranslated region , To test the significance of HuR in carcinogenesis of head and neck squamous cell carcinomas(HNSCCs), we have investigated HuH expression from 32 benign epithelial lesions , 14 prema lignant epitheli al lesions and 80 HNSCCs, There were two different staining patterns of HuR in HNSCCs : nuclear expression was seen in 78 7% (63 of 80) 01' cases; and an additional cyto plasmic expression was seen in 28, 7%(23 of 80) 01 cases, Nuclear expression of HuR was s ignificantly increased in premalignant lesions and HNSCCs, whereas increased cytoplasπli c expression of HuR was only observed in HNSCCs Cytoplasmic HuR expression was significantly increased in pa tients of HNSCC younger than 60 yea rs , Al though there was no significant correlation between a natomic s ites of HNSCCs and HuR express ion , cyto plasmic HuR expression was highly increased in HNSCCs of larynx, There was no significant co rrela tion between HuR expression and other clinicopathological parameters such as histological type‘ tumor s ize‘ 0 1' n odal s tatus , ln conclusion, this study s uggests that overexpression of HuR in HNSCCs may be part of a regula tory pathway tha t co ntro ls the mHNA stability 0 1' several important targets in carcinogenesis of HNSCCs

Human saliva conta ins a la rge number of proteins and peptides whose composition may alter as a conseq uence of disease. '1'0 date‘ however. the proteins and peptides that routinely populate t his oral fluid are largely unknown, '1'0 provid e a ca ta logue 이， sali va protei ns. we have surveyed the unstimulated human whole saliva by using shotgun proteomics. F'or the shotgun a pproach‘ whole sali va proteins were digested into peptides with ChemDigestD and the res ulting pe ptide fragments were sepa rated by RP- HPLC, followed by each fraction was tryptic di gestion ChemDiges tD- Trypsin diges ted pe pt ides were analyzed by tandem mass spectrometry (MS!MS) using a nano-LC equi pped quadru po le-time of fli ght rnass spect rometer, and the obtained spectra were searched against human protein sequence da tabase us ing MASCOT Shotgun proteomics a llowed a total of 291 human proteins to be confidently assigned. The largest gro u p (17 , 2%) of the identifi ed proteins sorted into functional categories was included in the s ignal transducti on function except for the hypothet ical or unknown functio n, This work provides a valuable starting point for the ana lys is of human sa l i va ry protei ns a nd theil‘ biological functions and candidates from human whole saliva that may prove to be of diagn ost ic and t herapeutic s ignif‘ Ica nce

Nickel powders were synthesized by the hydrazine reduction of nickel chloride solution containing ammonia in DEA solutions. The size distribution of nickel powders were investigated as a function of ammonia concentration, hydrazine concentration and the mixed composition ratio of diethanolammine (DEA) and triethanolammine (TEA). Nickel powders with the size in submicron range were obtained at for 45 minutes by hydrazine reduction of nickel chloride solution in DEA solutions. The hydrazine concentrations showed significant effects on the particle size and shape distribution of nickel powders under molar ratio of 2.0 condition. As the mixed volume ratio of TEA and DEA increased, nickel powders with relatively larger particle size and low agglomeration were obtained. Nickel powders with particle size in the ranged from 0.4 to were obtained at the 50 of TEA.

이 연구는 상하단 철근의 영향에 따른 철근콘크리트 보의 비틀림 강도를 평가하고자 단면의 상하단 철근의 R값을 변수로 비틀림 실험을 수행하였다. 실험체는 선행연구와 동일한 캔틸레버 형태로 총 2체를 제작하였으며, 1000kN의 액추에이터 2대 를 이용하여 가력을 실시하였다. 실험결과, 상하단 철근의 영향에 따라 비틀림 내력의 차이를 확인하였다.

In this study, an experiment was conducted to evaluate the behavior of fiber reinforced concrete beam according to GFRP(Glass Fiber Reinforced Polymer)sheets and based on previous specimens and directly compare the fiber reinforcing effect. As a result, all specimens, regardless of the cross section shape, had an increase in torsional capacity and similar behavior compared to previous study.

In order to investigate the confinement behavior of reinforced concrete columns using high strength materials, we performed loading tests on the columns with different combinations of reinforcement strength. Base on the test results together with previous studies, the confinement capacity of high strength reinforced concrete column was evaluated and the adequacy of the confinement design equation in the KCI code was discussed. As a result, it is found that the energy dissipation capacity increases as the yield strength increases.

이 연구는 유공보강근의 형상에 따른 철근콘크리트 유공 보의 전단저항성능을 평가하기 위하여 4체의 실험체를 제작하여 전단실험을 수행하였다. 실험의 주요변수는 유공의 유무, 유공보강 유무, 유공 보강근의 형상으로 하였으며, 제안 유공 보강근은 시공성을 고려하여 사각형과 마름모형이 혼합된 나선형 형태이다. 실험결과, 이 연구에서 제안된 유공보강근은 유공 주변의 균열을 효과적으로 제어하여 실험체의 전단력 향상에 효과적임을 확인하였다. 또한 현행설계기준은 유공 보강근을 배근한 실험체의 실험결과를 과소평가하는 것으로 나타났다.

This paper presents the seismic performance of the steel damper under reversed cyclic loading. The U-shaped steel damper used in this study was designed to have energy dissipation zone with an external diameter of 120 mm, a width of 15 mm, and a thickness of 15 mm. The cyclic loading test was carried out using an uniaxial universal testing machine with a capacity of 2,000 kN. The test results indicated that no strength deterioration of the specimen was found as well as the equivalent damping ratio of the specimen was excellent.

Spiral reinforcement in a circular column plays an effective role in the ductile behavior of a column through position fixing and buckling restraining of the longitudinal reinforcement, and confining core-concrete. Each country has suggested the minimum volumetric ratio of spiral reinforcement in order to secure the ductility of concrete columns. The minimum volumetric ratio of spiral reinforcement suggested by ACI 318-14 and the national concrete structure design standard was developed based on the theory of Richard et al. (1928); furthermore it has been used until now. However, their theory cannot consider the effects of high strength concrete and high strength reinforcement, and arrangement condition of the spiral reinforcement. In this study, a modified minimum volumetric ratio equation is suggested, which is required to improve the ductility of reinforced concrete circular columns and to recover their stress. The modified minimum volumetric ratio equation suggested here considers the effect of the compressive strength of concrete, the yield strength of spiral reinforcement, the cross sectional area of columns, the pitch of spiral reinforcements and the diameter of spiral reinforcement. In this paper, the validity of the minimum volumetric ratios from ACI 318-14 and this study was investigated and compared based on the results of uniaxial compression experiment for specimens in which the material strength and the spiral reinforcements ratio were used as variables. In the end of the study, the modification method for the suggested equation was examined.

작약 정식후 1년생은 일반관리법으로 재배하고 2년생부터 3년생 및 4년생까지 1년에 4회씩 지상부 병해에 적용약제를 살포하여 정상생육한 작약과 6, 7, 8, 9월 하순에 2년 및 3년동안 연속 고사한 작약을 10월 상순에 수확하여 수량과 paeoniflorin 함량을 조사하여 다음과 같은 결과를 얻었다. 경장, 경직경 및 주당 줄기수는 고사시기가 빠를수록 정상생육에 비해 감소하는 경향이었다. 주당 화뢰수는 정상생육한 3, 4년생이 각각 11.5개, 16.2개인데 비해 6월 하순 고사구는 각각 5.2개, 4.6개로 현저히 적었고, 측화수도 6월, 7월 하순 고사구가 정상생육에 비해 현저히 감소하였다. 재배년수별 지상부 고사시기에 따른 주근장 및 주근경은 3년생의 경우 정상생육이 각각 44.2cm, 20.7mm 인데 비해 6 월 하순고사구가 각각 38.7cm, 18.2mm 로 가장 많이 감소하였다. 상품성이 우수한 뿌리 굵기 10mm 이상의 뿌리수는 3, 4년 정상생육한 작약이 26.0개, 40.0개인데 비해 고사시기가 빠를수록 점차 감소하여 2, 3 년 연속 6월 하순에 고사한 작약은 각각 21.1개 , 33.2개로 가장 적었다. 건근수량은 3년 연속 고사한 4년생 작약에서 6월 하순 고사가 1,007kg/10a로 가장 낮았고, 정상생육구에서는 1,603kg/10a으로 유의적으로 높았다. paeoniflorin 함량은 3년생과 4년생 간에는 차이가 없었고, 고사시기가 빠를수록 증가하여 6월 하순 고사구가 가장 높았다. 뿌리굵기별 paeoniflorin 함량은 뿌리가 굵을수록 감소하였다.