In order to respond to environmental pollution, developed countries, including Korea, have begun to conduct research to utilize hydrogen energy. For mass transfer of hydrogen energy, storage as liquid hydrogen is advantageous, and in this case, the volume can be reduced to 1/800. As such, the transportation technology of liquefied hydrogen for ships is expected to be needed in the near future, but there is no commercialized method yet. This study is a study on the technology to test the performance of the components constituting the membrane type storage container in a cryogenic environment as a preparation for the above. It is a study to find a way to respond by analyzing in advance the problems that may occur during the shear test of adhesives. Through this study, the limitations of ISO4587 were analyzed, and in order to cope with this, the specimen was supplemented so that fracture occurred in the adhesive, not the adhesive gripper, by using stainless steel, a low-temperature steel, to reinforce the thickness. Based on this, shear evaluation was performed under conditions lowered to minus 243℃, and it was confirmed that the breaking strength was higher at cryogenic temperatures.

Conversion to modern hydrogen energy is required, and research on liquefied hydrogen cargo containment systems is needed for large-capacity transport and storage. In this study, changes in the mechanical properties of the adhesive required for storage and transport in liquid hydrogen were confirmed. The lap shear test was performed by realizing cryogenic conditions in a small chamber using liquid nitrogen and liquid helium. There was an increase of 11.0% in the -180℃ condition compared to room temperature, and an increase of 1.8% in the -230℃ condition compared to the -180℃ condition was confirmed. In the case of shear strain, it is known that it decreases as the temperature goes down. As a result of the experiment, it was confirmed that the value at room temperature and the value at -180℃ reduced the shear strain by 5.0%, and -230˚ compared to the -180℃ condition. An increase of 1.5% was confirmed in the C condition. In the case of the specimen tested at -230℃, the deformation in the gripper part was larger than in other tests, and it is judged that the maximum shear strength and shear strain were affected. In addition, in this study, there is a limitation in the experiment at -230°C rather than 253°C, which is the boiling point of hydrogen

최근 국내 구조물들의 노후화가 진행됨에 따라 구조물 보강과 관련된 연구에 대한 관심이 높아지고 있다. FRP보강은 노후화가 진행되어 성능이 저하된 구조물을 보강하는데 사용되며 주로 유리섬유 및 탄소섬유를 사용한다. 그러나 이 두 가지의 섬유는 경제적으로나 환경적으로나 나쁜 점이 있다. 따라서 본 연구에서는 친환경적이고 내열성이 우수한 현무암 섬유를 구조 용 보강재로 제시하고자 하였다. 또한 본 연구에서는 현무암 섬유에 가장 적합한 수지를 찾기 위하여 에폭시, 폴리에스테르 및 비닐에스테르를 함침 하였다.그 결과, 에폭시 수지를 사용하였을 때 가장 높은 인장 강도 및 탄성계수를 보였으며 전단강도 및 전단탄성계수가 타 수지에 비하여 50%정도 높게 측정되었다. 현무암섬유와 탄소, 유리 섬유의 물성을 비교한 결과 인장강도는 CFRF의 약 60%정도이나 GFRP보다 30%정도 높게 나타내었다.

PURPOSES : A geo-grid pavement, e.g., a stress-absorbing membrane interlayer (SAMI), can be applied to an asphalt-overlay method on the existing surface-pavement layer for pavement maintenance related to reflection cracking. Reflection cracking can occur when a crack in the existing surface layer influences the overlay pavement. It can reduce the pavement life cycle and adversely affect traffic safety. Moreover, a failed overlay can reduce the economic value. In this regard, the objective of this study is to evaluate the bonding properties between the rigid pavement and a SAMI by using the direct shear test and the pull-off test. The predicted fractural energy functions with the shear stress were determined from a numerical analysis of the moving average method and the polynomial regression method. METHODS : In this research, the shear and pull-off tests were performed to evaluate the properties of mixtures constructed using no interlayer, a tack-coat, and SAMI with fabric and without fabric. The lower mixture parts (describing the existing pavement) were mixed using the 25-40-8 joint cement-concrete standard. The overlay layer was constructed especially using polymer-modified stone mastic asphalt (SMA) pavement. It was composed of an SMA aggregate gradation and applied as the modified agent. The sixth polynomial regression equation and the general moving average method were utilized to estimate the interlayer shear strength. These numerical analysis methods were also used to determine the predictive models for estimating the fracture energy. RESULTS: From the direct shear test and the pull-off test results, the mixture bonded using the tack-coat (applied as the interlayer between the overlay layer and the jointed cement concrete) had the strongest shear resistance and bonding strength. In contrast, the SAMI pavement without fiber has a strong need for fractural energy at failure. CONCLUSIONS : The effects of site-reflection cracking can be determined using the same tests on cored specimens. Further, an empiricalmechanical pavement-design analysis using the finite-element method (FEM) must be done to understand the appropriate SAMI application. In this regard, the FEM application analysis and bonding property tests using cored specimens from public roads will be conducted in further research.

In the present study, exfoliated graphite nanoplatelets (xGnP) with different particle sizes were coated onto polyacrylonitrile-based carbon fibers by a direct coating method. The flexural properties, interlaminar shear strength, and the morphology of the xGnP-coated carbon fiber/phenolic matrix composites were investigated in terms of their longitudinal flexural strength and modulus, interlaminar shear strength, and by optical and scanning electron microscopic observations. The results were compared with a phenolic matrix composite counterpart prepared without xGnP. The flexural properties and interlaminar shear strength of the xGnP-coated carbon fiber/phenolic matrix composites were found to be higher than those of the uncoated composite. The flexural and interlaminar shear strengths were affected by the particle size of the xGnP, while the particle size had no significant effect on the flexural modulus. It seems that the interfacial contacts between the xGnP-coated carbon fibers and the phenolic matrix play a role in enhancing the flexural strength as well as the interlaminar shear strength of the composites.

합성보의 쉬어코넥트로 널리 사용되고 있는 스터드볼트는 현재 학회규준에 강재의 재질은 용접성을 고려한 SS400이 규정되어 있으며, 그 전단내력의 산정식은 압축강도 300kgf/cm2 이하의 콘크리트를 대상으로 하고 있다. 한편 합성구조의 보급에 따라 합성보 뿐만 아니라 다른 구조부분에서도 강재과 콘크리트를 결합하는 쉬어코넥트 혹은 다른 용도의 접합재의 필요성과 함께 강재와 콘크리트의 고강도화, 프리캐스트화가 예상된다. 따라서 본 연구에서는 고강도 콘크리트와 강부재를 결합하기 위한 고강도 스터드의 개발을 목적으로 행하여진 일련의 실험결과를 보고하였다. 또한 스터드의 강성을 증대시키기 위한 강관을 이용한 쉬어콘넥트(이하, 파이프 스터드라고 한다)를 고안하였다. 본 논문에서는 고강도 스터드의 용접성, 역학특성에 관한 실험적 검토와 동시에 고강도․고강성 스터드인 파이프 스터드의 강성․내력을 종래의 스터드 볼트와의 비교실험을 하여 파이프 스터드의 유효성을 검증한다.

Multi-walled carbon nanotube reinforced epoxy composites were fabricated using shear mixing and sonication. The mechanical, viscoelastic, thermal, and electrical properties of the fabricated specimens were measured and evaluated. From the images and the results of the measurements of tensile strengths, the specimens having 0.6 wt% nanotube content showed better dispersion and higher strength than those of the other specimens. The Young's moduli of the specimens increased as the nanotube filler content was increased in the matrix. As the concentrations of nanotubes filler were increased in the composite specimens, their storage and loss moduli also tended to increase. The specimen having a nanotube filler content of 0.6 wt% showed higher thermal conductivity than that of the other specimens. On the other hand, in the measurement of thermal expansion, specimens having 0.4 and 0.6 wt% filler contents showed a lower value than that of the other specimens. The electrical conductivities also increased with increasing content of nanotube filler. Based on the measured and evaluated properties of the composites, it is believed that the simple and efficient fabrication process used in this study was sufficient to obtain improved properties in the specimens.

본 연구에서는 아스팔트 콘크리트의 전단 물성을 고려한 영구변형 예측 모델을 개발하였다. 아스팔트 콘크리트의 전단 물성과 영구변형과의 상관성을 고찰하기 위해서 세 가지 종류의 아스팔트 콘크리트에 대해서 반복재하삼축압축(RLTC) 시험 및 삼축압축강도 시험과 간접인장강도 시험을 다양한 하중과 온도 조건에서 시행하였다. 주어진 아스팔트 콘크리트에 대하여 온도가 증가함에 따라 점착력은 감소하였으나 온도가 40℃ 이상인 경우 마찰각은 온도 변화에 민감하지 않은 거동을 나타내었다. 축차응력, 구속압, 온도 및 하중 주파수가 영구변형에 미치는 영향이 크다는 것을 관측할 수 있었다. 이러한 실내 시험 결과로 부터 아스팔트 콘크리트의 전단물성과 하중재하시간에 기초한 영구변형 모델을 개발하였다. 또한 일반적인 포장 단면에서 실시한 포장가속시험 결과를 이용해서 영구변형 모델을 보정하였다. 본 연구에서 제안한 영구변형 모델을 이용하여 다양한 온도와 하중조건에서 아스팔트 콘크리트의 영구변형을 예측할 수 있었다.

The rheological properties of concrete vary during pumping. In this study, the tests were conducted to evaluate whether changes in rheological properties of concrete during pumping occur only by pressure, or by both pressure and shear flow. A high-strength concrete with a design strength of 50 MPa was used in the experiment. From the test results, it was confirmed that the change of rheological properties of concrete during pumping was affected by both pressure and shear flow.

In this study, Lead Rubber Bearing(LRB) characteristics calculated by the design of the seismic isolation system, according to the seismic isolation structure with the application of nuclear power plants. Experiments were carried out to analyze the compression characteristics of prototype LRB under variable shear displacement.