In this study we examine variations in the structure of perovskite compounds of LaBa2Cu2O9, LaBa2CaCu3O12 and LaBa2Ca2Cu5O15 synthesized using the solid state reaction method. The samples’ compositions were assessed using X-ray fluorescence (XRF) analysis. The La: Ba: Ca: Cu ratios for samples LaBa2Cu2O9, LaBa2CaCu3O12 and LaBa2Ca2Cu5O15 were found by XRF analysis to be around 1:2:0:2, 1:2:1:3, and 1:2:2:5, respectively. The samples’ well-known structures were then analyzed using X-ray diffraction. The three samples largely consist of phases 1202, 1213, and 1225, with a trace quantity of an unknown secondary phase, based on the intensities and locations of the diffraction peaks. According to the measured parameters a, b, and c, every sample has a tetragonal symmetry structure. Each sample’s mass density was observed to alter as the lead oxide content rose. Scanning electron microscope (SEM) images of the three phases revealed that different Ca-O and Cu-O layers can cause different grain sizes, characterized by elongated thin grains, without a preferred orientation.

BNKT Ceramics, one of the representative Pb free based piezoelectric ceramics, constitutes a perovskite(ABO3) structure. At this time, the perovskite structure (ABO3) is in the form where the corners of the octahedrons are connected, and in the unit cell, two ions, A and B, are cations, A ion is located at the body center, B ion is located at each corner, and an anion O is located at the center of each side. Since Bi, Na, and K sources constituting the A site are highly volatile at a sintering temperature of 1100℃ or higher, it is difficult to maintain uniformity of the composition. In order to solve this problem, there should be suppression of volatilization of the A site material or additional compensation of the volatilized. In this study, the basic composition of BNKT Ceramics was set to Bi0.5(Na0.78K0.22)0.5TiO3 (= BNKT), and volatile site (Bi, Na, and K sources) were coated in the form of a shell to compensate additionally for the A site ions. In addition, the physical and electrical properties of BNKT and its coated with shell additives(= @BNK) were compared and analyzed, respectively. As a result of analyzing the crystal structure through XRD, both BNKT(Core) and @BNK(Shell) had perovskite phases, and the crystallinity was almost similar. Although the Curie temperature of the two sintered bodies was almost the same (TC = 290 ~ 300 ℃), it was confirmed that the d33 (piezoelectric coefficient) and Pr (residual polarization) values were different. The experimental results indicated that the additional compensation for a shell additive causes the coarsening, resulting in a decrease in sintering density and Pr(remanent polarization). However, coating shell additives to compensate for A site ion is an effective way to suppress volatilization. Based on these experimental results, it would be the biggest advantage to develop an eco-friendly material (Lead-free) that replaced lead (Pb), which is harmful to the human body. This lead-free piezoelectric material can be applied to a biomedical device or products(ex. earphones (hearing aids), heart rate monitors, ultrasonic vibrators, etc.) and skin beauty improvement products (mask packs for whitening and wrinkle improvement).

This study examines the textual structure and speech acts within the inaugural addresses of the ministers in the Yoon Suk Yeol Government’s first cabinet. These addresses typically follow a three-part structure: introduction, development, and closing. The introduction features an opening greeting, while the development stage outlines the main service and missions, and presents requests to organizational members. The closing stage concludes the address. The introduction and closing are often simple enumerations of contents, whereas the development stage is logically and coherently structured. In terms of speech acts, the introductory stage predominantly features expressive acts. The development stage is marked by announcements and requests, while the closing e ncompasses various acts including statements, promises, and solicitations.

Recently, Free-Form and Irregular Shape high-rise buildings are constructed by IT technology development. Tilted shaped high-rise building which is one of Irregular shape high-rise buildings can cause lateral displacement by gravity load and lateral load due to tilted elevation shape. Therefore, it is necessary to review the behavior and structural aspects of the Tilted shape high-rise building by gravity load. In this paper, the dynamic characteristics of a tilted structure with a dual-core were analyzed with the core location as a design variable, and response behavior, vulnerable members, and vulnerable layers to earthquake loads were analyzed. As a result of the analysis, as the location of the core moved in an tilted direction, the eccentric distance and eccentric load decreased, reducing the axial force of the vertical members. However, the location of the core had little effect on the response.

Reliable, inexpensive, environment-friendly, and durable properties of carbon materials with unique and outstanding photoelectric performance is highly desired for myriad of applications such as catalysis and energy storage. Since lattice modulation is a vital method of surface modification of materials, which form by an external force during the synthesis process, causing the internal compression and stretching, leading to lattice sliding event. In this review, we present a summary of different methods to tailor the lattice modulation in 2D carbon-based materials, including grain/twin boundary, lattice strain, lattice distortion, and lattice defects. This overview highlights the implication control of the diverse morphologies of nanocrystals and how to tailor the materials properties without adding any polymers. The improvement in the performance of 2D carbon materials ranges from the enhancement of charge transport and conductivity, structural stability, high-performance of light absorption capacity, and efficient selectivity promote the future prospect of 2D carbon materials broaden their applications in terms of energy conversion and storage. Finally, some perspectives are proposed on the future developments and challenges on 2D carbon materials towards energy storage applications.

Cars using diesel have always had problems with reducing exhaust fumes, and have been studied steadily in this regard. There were studies on the remanufacturing effect of DOC catalyst deactivated by diesel vehicle smoke reduction device, analysis of vehicle fire accident cases caused by damage to diesel vehicle smoke reduction device, and related studies on the remanufacturing effect of diesel vehicle smoke reduction device DPF. This study is also to develop a burner structure in a smoke reduction device suitable for an exhaust engine to completely burn smoke generated by an engine using a diesel engine in a low-temperature exhaust gas. The main systems to be developed are high-performance heaters, burner structures that can maintain ignition in exhaust flows, and exhaust flow control units that reduce exhaust gas backflow effects caused by diesel engines.

최근 지구 온난화의 영향으로 태풍의 파괴력이 증가함에 따라 부유식 해상풍력발전기의 막대한 유실과 붕괴에 대한 우려가 깊어지고 있다. 부유식 해상풍력발전기의 안전한 운영을 위해 새로운 형태의 탈착형 계류 시스템 개발이 요구되고 있다. 본 연구에서 고 려한 새로운 반잠수식 계류 풀리는 기존의 탈착형 계류 장치에 비해 계류 라인으로 부유식 해상풍력 터빈을 보다 쉽게 탈부착할 수 있도 록 고안되었다. 8MW급 부유식 해상풍력발전기에 적용 가능한 반잠수식 계류 풀리의 초기 설계에 대한 구조적 안전성을 검토하기 위해 3D 프린터를 이용하여 축소구조모형을 제작하고, 이 모형에 대한 구조시험을 수행하였다. 축소 모형의 구조시험을 위해 3D 프린팅에 사 용된 ABS 소재의 인장 시편을 제작하고 인장시험을 수행하여 소재의 물성을 평가하였다. 인장시험에서 얻은 재료 특성과 축소모형 구조 시험과 동일한 하중 및 경계 조건을 적용하여 반잠수식 계류 풀리의 유한요소해석을 수행하였다. 유한요소해석을 통해 반잠수식 계류 풀 리의 구조적 취약 부분을 검토하였다. 반잠수식 계류 풀리의 주요 하중조건을 고려하여 구조모형시험을 수행하였으며, 재료의 최대인장 응력 이상이 발생하는 위치에 대해 유한요소해석과 시험 결과를 비교하였다. 유한요소해석과 모형시험의 결과로부터 작동조건에서는 Body와 Wheel의 연결부 구조가 취약한 것으로 파악되었고, 계류조건에서는 Body와 Chain stopper의 연결부 구조가 취약한 것으로 검토되었 다. 축소모형 구조시험에서 나타난 SMP의 구조 취약부는 구조해석의 결과와 일치하는 것으로 나타났다. 연구 결과를 통해 반잠수식 계류 풀리의 초기 설계에 대한 구조적 안전성을 실험적으로 검증할 수 있었다. 또한, 본 연구 결과는 상세설계 단계에서 반잠수식 계류 풀리의 구조 강도를 향상시키는데 유용하게 활용될 수 있을 것으로 판단된다.

Epoxy-based composites find extensive application in electronic packaging due to their excellent processability and insulation properties. However, conventional epoxy-based polymers exhibit limitations in terms of thermal properties and insulation performance. In this study, we develop epoxy-based siloxane/silica composites that enhance the thermal, mechanical, and insulating properties of epoxy resins. This is achieved by employing a sol–gelsynthesized siloxane hybrid and spherical fused silica particles. Herein, we fabricate two types of epoxy-based siloxane/ silica composites with different siloxane molecular structures (branched and linear siloxane networks) and investigate the changes in their properties for different compositions (with or without silica particles) and siloxane structures. The presence of a branched siloxane structure results in hardness and low insulating properties, while a linear siloxane structure yields softness and highly insulating properties. Both types of epoxy-based siloxane/silica composites exhibit high thermal stability and low thermal expansion. These properties are considerably improved by incorporating silica particles. We expect that our developed epoxy-based composites to hold significant potential as advanced electronic packaging materials, offering high-performance and robustness.

지리산 국립공원 내 구상나무림의 종조성과 식생구조를 파악하기 위하여 구상나무 자생지역에 약 400㎡ 면적의 조사구 49개소를 설정하여, 식물사회학적 방법에 따라 현장조사를 실시하고, 이원지표종분석(TWINSPAN)과 표조작법을 병용하여 군집 분류를 실시했다. 그 후 군집 유형별 중요치를 활용한 종조성 분석, 종다양도 분석, 흉고직경급 분석, 치수 분석 및 유사도 분석을 시행하였다. 군집 분류 결과, 지리산의 구상나무림은 A, B, C, D, E 등 총 5개의 군집으로 분류되었다. 관중-함박꽃나무-조릿대와 미역취-사스래나무-실새풀에 의하여 2개의 군집으로 구분되며, 전자는 층층나무-산수국에 의하여 A, B 유형으로 구분되었다. 후자는 마가목-진달래 군집과 전형군집인 E 유형으로 구분되고, 가문비나무-곰취와 단풍취에 의하여 C, D 유형으로 구분되었다. 식생 분석을 통해 지리산 구상나무림은 구상나무, 신갈나무, 당단풍나무, 쇠물푸레나무, 사스래나무 등의 중요치가 높게 나타났으며, 종다양도의 경우 선행 연구에서 나타난 지리산 구상나무림의 종다양도와 유사한 결과를 나타내었다. 흉고직경급 분석 결과 전 층위에서 구상나무가 우점하며 치수 생장도 양호하여 당분간 구상나무의 우점이 유지될 것으로 판단하나, 추후 증가할 것으로 예상되는 생물다양성의 가치와 기후변화로 인한 위협을 고려하였을 때, 지속적인 모니터링을 실시하여 각종 위협에 대응하는 체계적인 보전 및 관리가 요구된다.

Although the abundance of Metapenaeus joyneri resources with high commercial value was recently confirmed in the outer waters of Gomso Bay, located between Buan-gun and Gochang-gun, Jeollabuk-do, Metapenaeus joyneri resources have not been efficiently utilized due to the absence of fishing gears and methods for a selective Metapenaeus joyneri capture. Therefore, in this study, we adopted shrimp dredge as a trial fishing gear for the Metapenaeus joyneri capture, and analyzed the species composition and cluster community structure of aquatic organisms caught by the shrimp dredge, from May to September 2021 at the coastal waters of Gochang-gun, Jeollabuk-do. During the experimental period, 28 types of marine species of 29,190 individuals and 250,136 g of total biomass were caught. Among them, the population of Metapenaeus joyneri, the target species, dominated by 80.7%, followed by Thrysa chefuensis with 7.1%, and Leiognathus nuchalis with 6.0%, confirming that the fishing ratio of Metapenaeus joyneri was the highest among all species.

본 논문에서는 한국전통게임에 사용되는 접이식 종이구조물(이하 딱지)의 접이과정을 모델링하고 게임의 승리조건을 만족시키는 충돌조건을 유전알고리즘을 이용하여 산정하는 과정을 서술하였다. 딱지는 A4용지 2장으로 구성되는 것을 가정하였다. 접이과정은 강제경계조건을 부여하여 날개부분을 꼬임의 위치로 변형시키고 강체판의 강제경계조건을 이용하여 딱지를 압착하였다. 이후 복원 력에 의한 완화해석을 수행하여 게임에 사용된 딱지의 형상과 응력상태를 구성하였다. 얻어진 동일한 2개의 딱지 중 타격딱지를 주어 진 충돌위치로 강제변위에 의해서 이동시키고 주어진 충돌속력에 대한 충돌해석으로 게임의 진행과정을 해석하였다. 이 때 승리조건 인 피격딱지의 반전을 일으키는 충돌조건을 산정하기 위하여 유전알고리즘을 이용한 최적화해석을 수행하였다. 이 과정에서 효율적 인 해석을 위하여 충돌해석을 2단계로 나누고 1단계의 해석결과 피격딱지에 반전이 발생할 가능성이 있는 경우에만 2단계해석을 진 행하였다. 1단계 해석에서 유전알고리즘의 적합함수는 피격딱지의 방향코사인이었고 2단계해석에서는 속도의 역수로 하여 전체적 으로는 가장 낮은 충돌속력을 가지는 충돌조건을 찾아내고자 하였다. 해석수행결과 다양한 압착두께에 따른 최적의 충돌조건을 찾아 낼 수 있었다.

The application of mindfulness is increasing significantly in different areas of business studies. However, identifying how mindfulness research has evolved and the major research themes, specifically within the business studies domain, remains lacking. This study unveils the intellectual structure of mindfulness research in business studies. Using citation and co-citation analysis, the study identifies the most influential articles, annual growth, and three key research clusters constituting the intellectual foundation.

In this conceptual paper, we use the multiple agency theory to explain the governance issues in cross-sector partnerships. In doing so, we identify five typologies of cross-sector partnerships, each distinct from one another in terms of the governance structure. We also discuss three problems that occur in these relationships, mainly differences in institutional logic, temporal differences, and free-riding and opportunistic behavior, as well as how these problems affect each type of cross-sector partnership. These findings make several significant contributions to the literature and theories. First, this is one of the few studies to use agency theory to examine the governance structures and problems in cross-sector partnerships. Second, our study further contributes to solidifying our understanding of the agency problems arising in cross-sector collaborations. Lastly, our study confirms their presence in other types of cross-sector partnerships as well and we maintain that these problems do not affect each type of cross-sector partnership in the same way, leading us to offer more nuanced implications for researchers and practitioners.

As millennials are continuously growing; hence they are considered today's fine jewelry business treasure. Understanding why they buy fine jewelry using the means-end theory is the key objective of this study. Brand, function and beauty are means that lead to happiness and self-confidence, the end value of millennials mindset

In the fluid-structure interaction analysis, the finite element formulation is performed for the wave equation for dynamic fluid pressure, and the dynamic pressure is defined as a degree of freedom at the fluid nodes. Therefore, to connect the fluid to the structure, it is necessary to connect the degree of freedom of fluid dynamic pressure and the degree of freedom of structure displacement through an interface element derived from the relationship between dynamic pressure and displacement. The previously proposed fluid-structure interface elements use conformal finite element meshes in which the fluid and structure match. However, it is challenging to construct conformal meshes when complex models, such as water purification plants and wastewater treatment facilities, are models. Therefore, to increase modeling convenience, a method is required to model the fluid and structure domains by independent finite element meshes and then connect them. In this study, two fluid-structure interface elements, one based on constraints and the other based on the integration of nonsmooth functions, are proposed in nonconformal finite element meshes for structures and fluids, and their accuracy is verified.

Essential macleod program (EMP) was used to optimize the transmittance of the transparent conducting layers in an oxidemetal- oxide structure. For EMP simulation, the optical coefficient of the material was extracted using an ellipsometer. Following the simulation studies, oxide-metal-oxide samples were fabricated experimentally, and their optical and electrical properties were analyzed. Multilayer SiInZnO/Ag/Siinzno (S/A/S) structures were grown on glass substrates using radio frequency (RF) and direct current (DC) sputtering at room temperature. Due to the occurrence of destructive interference at the metal and oxide interface, the S/A/S structure exhibited excellent optical properties. As the thickness of the top and bottom oxide layers was increased, the transmittance spectrum was red-shifted due to partial wave interference at the Ag interface. Change in thickness of the top oxide layer had a greater effect on the transmittance than that of the bottom oxide layer. This was due to the difference in refractive index occurring at each interface. Change in Ag thickness shifted the absorption edge in the short wavelength region. Whereas electrical properties, such as sheet resistance and carrier concentration, were found to be dependent on thickness of the sandwiched metal layer. An excellent figure of merit of 63.20 ×10−3Ω−1 was obtained when the thickness of the Ag layer was 11 nm, and the top and bottom oxide layer thickness were 45 and 60 nm, respectively. These values suggest promising optoelectronic properties and are encouraging for future transparent electrode applications.