간행물
한국기계기술학회 학술대회논문집 Proceedings of KSMT Annual Meeting 學術大會論文集
- 발행기관 한국기계기술학회
- 자료유형 학술대회
- 간기 연간
- 수록기간 2000 ~ 2023
- 주제분류 공학 > 기계공학 공학 분류의 다른 간행물
- 십진분류KDC 550DDC 620
권호리스트/논문검색
2015년도 한국기계기술학회 추계학술발표회 논문집 (2015년 11월) 27건
21.
2015.11
구독 인증기관·개인회원 무료
This study investigates the mechanical behavior at the compression of bonded aluminum foam. Four kinds of specimen thicknesses are 25, 50, 75 and 100mm. These aluminum foams are compressed with the speed of 5mm/min. The reaction forces in cases of 25, 50, 75 and 100mm are 2510, 5080, 7700 and 10400N respectively. The equivalent stresses are 0.96, 1.00, 1.02 and 1.03MPa respectively. These analysis results are verified by comparing with the experimental results. The results of this study can be contributed to the safe design of structure.
22.
2015.11
구독 인증기관 무료, 개인회원 유료
In the present study, numerical analysis algorithm for the hull form optimization was taken into account using optimization algorithm. In this algorithm the sequential quadratic programming method was applied as an optimizer and the potential-based panel method was adopted to get the wave resistance coefficient as the objective function. The hull form was modified using the B-spline surface modeling technique during the whole optimization process. The developed numerical analysis algorithm was applied to a passenger ship and the optimized ship were compared with the original ship.
4,000원
23.
2015.11
구독 인증기관 무료, 개인회원 유료
The grid pattern electromagnetic interference(EMI) shielding sheet for the wireless charger has been designed using grid pattern metal sheet, PET & DST stacking and laminating technology. Also, an automatic manufacturing system of the grid pattern EMI shielding sheet for the wireless charger is developed. This metal sheet with grid pattern is an effective shield against EMI that can not shield completely by existing single metal sheet. And the developed automatic manufacturing system having a laminated productivity exceeds the 8m/min can stack and lamination thin metal sheets without any wrinkles.
4,000원
24.
2015.11
구독 인증기관·개인회원 무료
CFRP has the high strength and low weight. But it tends to be frail if it is applied with the mechanical bonding method using weld, rivet or bolt. So, the chemical bonding method using the special adhesive has been utilized. By applying the bonding method with the adhesive, this paper investigates the mechanical property of DCB specimen bonded with the type of mode 2 through the simulation analysis. Four kinds of specimen thicknesses are 25mm, 35mm, 45mm and 55mm in this study. The mechanical behaviors of specimens due to the forced displacements are investigated as the distributions of equivalent stresses. The reaction force becomes higher as the specimen thickness is increased. The result of this study about the fracture property of adhesive joint is thought to be contributed to the safe design of structure with CFRP.
25.
2015.11
구독 인증기관 무료, 개인회원 유료
Graphene could be damaged and contain impurities on its surface while several fabrications such as deposition, etching, and patterning because one needs photoresist masking operation to divide the section for deposition or not. In this paper, we investigated the effectiveness of selective atomic layer deposition for clean graphene surface. Atomic layer deposition (ALD) has strong point at very uniform conformity of 1 rms roughness. In this process, H2O is generally used by one of precursors. This H2O precursor make deposition of ALD on hydrophilic surface not hydrophobic. Therefore, we used this property at graphene which has hydrophobic surface. And then, we analyzed selective deposition of ALD on graphene which are grown on Cu foil and transferred by wet process not cleaved from HOPG.
3,000원
26.
2015.11
구독 인증기관 무료, 개인회원 유료
In this study, the horizontal automatic scum remover with buoyant type is developed to reduce the cost of facility and is suitable for unit-process automation. This system is consist of the scum collecting box, leveling device for scum collecting box, drive device for scum collecting box, water level sensor and indicator, departure prevention device of scum collecting box, setting monitor, main control panel, etc. Performance tests for the system such as the accuracy of the scum thickness measurement, horizontal degree of the scum collecting box, scum removal time, accuracy of an unmanned control have been performed. The performance of the prototype system satisfies all the objects of this study.
4,000원
27.
2015.11
구독 인증기관 무료, 개인회원 유료
Electric vehicles will be further increased with the development of technology and the increasing demand of customer in the near future. Thus, the stable supply of the core material used in an electric vehicle that can be required. In this paper, It explores the prospects on a material, as base metal like copper and rare metal like lithium , etc., for electric vehicles through the example of Japan.
3,000원
1
2
