This is a study on the distribution of acoustic emission parameters during a burst test for a type-II CNG vehicle fuel tank. A resonant AE sensor with a central frequency of 150 kHz was attached to the composite materials in the center of the fuel tank. The pressure was increased from 30 to 100% of the expected burst pressure and was maintained for 10 minutes at each level. Damage at 70% of expected burst pressure occurred by various damage mechanisms including fiber breakage and delamination, while that of below 60% only occurred by matrix crack initiation and growth. The count, duration and rise time of the AE signal at 60% of the expected burst pressure are distributed below 500, 5000 μs and 300 μs, respectively. Then, at above 70% they increased with pressure by superimposing of individual AE signal generated at a nearby place. These results confirmed that the analysis of the distribution of AE parameters is an effective tool for estimating damage of a CNG fuel tank.

최근 연구들에 따르면 경제에 대한 개인투자자들의 낙관적인 견해가 실제 투자에 상당한 영향을 준다는 점을 지적하고 있다. Zuckerman(2009)은 헤지펀드 매니저들조차도 집권정당에 따라 투자패턴을 달리한다고 주장하고 있다. 특히 최근 들어 미국경제의 불안정한 움직임에 따라 일부 헤지펀드 매니저들은 미국경제에 대한 회의감으로 주식시장에서 관망하는 자세를 보이고 있다. 이는 정부정책이 경제회복으로 이어질 수있을 지에 대한 확신이 없기 때문이다. 한편 이러한 비관론자 성향의 일부 헤지펀드 및 뮤추얼펀드 매니저들은 펀드매니저들 평균보다 못 미치는 성과를 나타내었다. 반면에 지지하는 정당이 집권하였을 때, 개인투자자들은 경제의 불확실성(uncertainty)이 줄어들고 주가도 상승할 것이라고 믿는 경향이 있다. 이러한 성향은 개인투자자들이 지지한 집권정부가 들어섰을 경우 실제로 주식투자 규모를 늘려가는 상황을 만들며, 소형주(small cap)를 비롯하여 가치주(value stocks), 경기민감주 등에 대한 투자규모를 늘리는 경우가 흔히 발생한다. 이러한 새로운 정부에 대한 기대감이 반영되어 새로운 정부의 집권 초기에는 이들 개인투자자들은 주식보유기간을 보다 길게 가져가려는 경향도 보인다. 반면에 개인투자자들의 경우 자신이 지지하지 않은 집권정부가 들어섰을 때 경제의 불확실성(uncertainty)이 증가한다고 판단하여 보유주식을 처분하려는 경향이 증대되고 있다. 이러한 연구에는 Hirshleifer(2001)과 Kumar(2009a) 등이 있으며, 국제 포트폴리오를 하는 미국의 개인투자자들은 불확실성의 증가에 따라 국외 주식들을 처분하고 안전자산 선호현상으로 인하여 미국 내의 주식시장에 대한 투자 비중을 늘려나가는 경향을 보이고 있다.

In this study, optical emission spectroscopy was used to monitor the plasma produced during the RF magnetron sputtering of a BaTiO3 target. The intensities of chemical species were measured by real time monitoring with various discharge parameters such as RF power, pressure, and discharge gas. The emission lines of elemental and ionized species from BaTiO3 and Ti targets were analyzed to evaluate the film composition and the optimized growth conditions for BaTiO3 films. The emissions from Ar(I, II), Ba(I, II) and Ti(I) were found during sputtering of the BaTiO3 target in Ar atmosphere. With increasing RF power, all the line intensities increased because the electron density increased with increasing RF power. When the Ar pressure increased, the Ba(II) and Ti(I) line intensity increased, but the Ar+ line intensity decreased with increasing pressure. This result shows that high pressure is of greater benefit for the ionization of Ba than for that of Ar. Oxygen depressed the intensity of the plasma more than Ar did. When the Ar/O2 ratio decreased, the intensity of Ba decreased more sharply than that of Ti. This result indicates that the plasma composition strongly depends on the discharge gas atmosphere. When the oxygen increased, the Ba/Ti ratio and the thickness of the films decreased. The emission spectra showed consistent variation with applied power to the Ti target during co-sputtering of the BaTiO3 and Ti targets. The co-sputtered films showed a Ba/Ti ratio of 1.05 to 0.73 with applied power to the Ti target. The films with different Ba/Ti ratios showed changes in grain size. Ti excess films annealed at 600˚C did not show the second phase such as BaTi2O5 and TiO2.

 ,  , Temperature-related parameters of Panonychus citri (McGregor) (Acarina: Tetranychidae) development were estimated and a stage-structured matrix model was developed. The lower threshold temperatures were estimated as 8.4℃ for eggs, 9.9℃ for larvae, 9.2℃ for protonymphs, and 10.9℃ for deutonymphs. Thermal constants were 113.6, 29.1, 29.8, and 33.4 degree days for eggs, larvae, protonymphs, and deutonymphs, respectively. Non-linear development models were established for each stage of P. citri. In addition, temperature-dependent total fecundity, age-specific oviposition rate, and age-specific survival rate models were developed for the construction of an oviposition model. P. citri age was categorized into five stages to construct a matrix model: eggs, larvae, protonymphs, deutonymphs and adults. For the elements in the projection matrix, transition probabilities from an age class to the next age class or the probabilities of remaining in an age class were obtained from development rate function of each stage (age classes). Also, the fecundity coefficients of adult population were expressed as the products of adult longevity completion rate (liiongevity) by temperature-dependent total fecundity. To evaluate the predictability of the matrix model, model outputs were compared with actual field data in a cool early season and hot mid to late season in 2004. The model outputs closely matched the actual field patterns within 30 d after the model was run in both the early and mid to late seasons. Therefore, the developed matrix model can be used to estimate the population density of P. citri for a period of 30 d in citrus orchards.

이 논문에서는 환경변수의 시계열 분포도 작성과 불확실성 모델링을 위해 시공간영역으로 확장된 다중 가우시안 크리깅을 제안하였다. 다중 가우시안 틀 안에서, 우선 정규점수변환된 환경변수를 결정론적 경향 성분과 확률론적 잔차 성분으로 분해하였다. 그리고 시간 경향 모델 계수의 내삽을 통해 경향 성분의 시계열 공간 분포도를 작성하였다. 정상성 잔차 성분의 시공간 상관 구조는 곱-합 시공간 베리오그램 모델을 이용하여 정량화하였고, 이 베리오그램 모델과 시공간 크리깅을 이용하여 국소적 누적 확률분포함수를 모델링하였다. 이 국소적 누적 확률분포함수로부터 평균값과 조건부 분산을 계산하여 공간분포도 작성과 불확실성 분석에 각각 이용하였다. 제안 기법의 적용성 평가를 위해 인천광역시에서 3년간 13개 관측소에서 측정된 월 평균 미세먼지(PM10) 농도 자료를 이용한 시계열 분포도 작성 사례 연구를 수행하였다. 사례연구 결과, 제안 기법을 통해 기존 공간 정규 크리깅에 비해 작은 편향과 높은 예측 능력을 가진 시계열 미세먼지(PM10) 농도 분포도 작성이 가능함을 확인할 수 있었다. 또한 조건부 분산과 특정 농도값을 초과할 확률값들은 해석을 위한 유용한 보조 정보를 제공하였다.

Predictive mathematical models were developed for predicting the kinetics of growth of Listeria monocytogenes in smoked salmon, which is the popular ready-to-eat foods in the world, as a function of temperature (4, 10, 20 and 30℃). At these storage temperature, the primary growth curve fit well (r² = 0.989~0.996) to a Gompertz equation to obtain specific growth rate (SGR) and lag time (LT). The Polynomial model for natural logarithm transformation of the SGR and LT as a function of temperature was obtained by nonlinear regression (Prism, version 4.0,GraphPad Software). Results indicate L. monocytogenes growth was affected by temperature mainly, and SGR model equation is 365.3-31.94*Temperature+0.6661*Temperature^2 and LT model equation is 0.1162-0.01674*Temperature+0.0009303*Temperature^2. As storage temperature decreased 30℃ to 4℃, SGR decreased and LT increased respectively. Polynomial model was identified as appropriate secondary model for SGR and LT on the basis of most statistical indices such as bias factor (1.01 by SGR, 1.55 by LT) and accuracy factor (1.03 by SGR, 1.58 by LT).

본 실험은 압출성형을 통한 저DE덱스트린 제조공정을 확립하기 위해서 수분함량 25, 35% 배럴온도 100, 120oC, 스크루 회전속도 150, 250 rpm에서 압출성형한 전분을 알파아밀라아제로 당화시켰을 때 당화특성을 연구하였다. 수분용해지수는 원료전분 수분함량이 25%로 감소할 경우 증가되었으며, 수분흡착지수도 수분의 감소와 함께 전체적으로 증가하였다. 환원당함량의 경우 수분함량이 낮고 배럴온도 높을수록 증가되었다. 120 분간 당화 후 DE 63.8로 높게 나타났다. 비기계적 에너지 투입량(SME)의 증가와 함께 수분용해도는 증가하는 경향이었다. 또한 수분함량의 감소와 함께 비기계적 에너지 투입량과 수분용해도는 증가하였다. 페이스트점도는 원료전분의 수분이 낮고, 스크루 회전 속도가 증가할수록 전분사슬의 절단에 따라 저온최고점도가 감소하는 경향을 보였다. 초기반응속도는 수분함량이 25%로 낮고 배럴온도 120oC, 스크루 회전수 250 rpm에서 2.26 × 10−3mmol/mL·min로 가장 높았다. 시중 호화전분 1.83 × 10−3mmol/mL·min에 비해서도 높은 결과를 보였다. 당화속도상수는 히구치모델을 응용하였으며, 수분함량이 낮고 배럴온도가 120oC일 때 전체적으로 높게 나타났다. 본 실험에서 초기반응속도, 당화속도상수, 당화수율 등을 고려할 때, 최적조건은 수분함량 25%, 배럴온도 120oC, 스크루 회전속도 250 rpm이었다.

The purpose of this study was to investigate the effect of high heeled shoes with the total contact insert (TCI) on the frontal plane of the joints for the lower extremity during the gait. Ten healthy females voluntarily participated in this study and the height of the high heeled shoes was 7 cm. A three-dimensional motion analysis system (VICON) and force plates were used to analyze the movements of the joints for the lower extremities. The results were as follows: There were no significant differences for the angle value on the event of the gait cycle in the maximum eversion and inversion of the ankle joint, the varus and valgus of the knee joint, and the adduction and abduction of the hip joint (p>.05). But, there was a significant difference or the range of motion in the ankle joint (p<.05). The value of ankle and knee moment with a TCI was less than the value for no TCI. And there were significant differences for the moment value of the maximum inversion and eversion on the ankle joint and for the maximum varus and valgus on the knee joint (p<.05). Therefore, a TCI would be effective in stabilizing the joints of the lower extremities and increasing the balance of a body to reduce the injure from a fall during the gait.

현재까지 축적된 많은 연구결과와 설계기준을 바탕으로 일반적인 중실단면을 갖는 철근콘크리트 교각의 경우 큰 어려움 없이 내진설계가 수행되고 있지만, 중공원형 철근 콘크리트 교각의 경우 실험 및 해석상의 어려움으로 인하여 국내 외적으로 심부구속철근 상세에 대한 명확한 설계기준과 함께 이에 대한 합리적인 구속 모델 및 내진 성능평가 방안 등은 아직까지 미비한 실정이다. 본 연구에서는 주요 설계변수에 따른 중공원형 철근콘크리트 교각의 내진거동 특성을 파악하고, 이를 신뢰성 있는 비선형 유한요소해석 프로그램(RCAHEST)을 통한 결과와의 비교 분석을 바탕으로 보다 경제적이고 합리적인 설계방안 마련을 위한 기초자료를 제시하고자 한다.

As the quality of a weld joint is strongly influenced by process parameters the welding process, an intelligent algorithms that can predict the bead geometry and shape to accomplish the desired mechanical properties of the weldment should be developed. In this study, prepared by Φ1.6mm GMA welding of metal wire nose Advice jowelui 350A 600A grade level inverter welder and DAIHEN SCR's were carried out using welding. Welding conditions were 5.5m/min wire feed rate the welding current is rapidly transmit approximately 260A, welding voltage was about 30V. CTWD a 22mm, shielding gas was Ar 20L/min and the welding speed was a 240mm/min. Using data collected during welding equipment welding current and welding voltage waveform was analyzed by measuring the volume of the transition mode. Addition of CaCO3 as a loss of the spread of the weld bead dilution rate decreased, suggesting that, GMA in the overlay welding bead shape control, dilution control and may be used as a welding flux is considered. Stabilizing effect of the arc by the Ca-containing CaF2, CaCO3, CaMg(CO3)2, respectively, welding flux 0.1wt.% added GMA welding and weld overlay were evaluated with dilution, CaF2, and CaMg(CO3)2 added to the dilution of Seemed to increase.

Poisson model and Gamma-Poisson model are popularly used to analyze statistical behavior from defective data. The methods are based on binary criteria, that is, good or failure. However, manufacturing industries prefer polytomous criteria for classifying

The purpose of this study was to select market variables that a foodservice company should consider when expanding overseas and to regional market analysis by variables. Twenty-three different variables were derived from 17 previous studies. These were: population, urbanization rate, women employed, enrollment in tertiary education, gross domestic product, value added by service, total number of mobile cellular telephone subscribers, number of internet users, total Asian highway, inward foreign direct investment, total service imports, inflation rate, international tourist arrivals, energy use by industry, growth rates of the food consumer price index, access to urban sanitation, per capita total expenditure on health, male life expectancy at birth, adult literacy rate, contributing women family workers, passenger car, and country risk assessment. The selected variables were collected as secondary data from the UN, Asian Development Bank, International Bank for Reconstruction and Development, and Michigan State University.

The purpose of this study was to investigate the variations in gait parameters in terms of the type of arm sling used in hemiplegic patients. Ten patients with hemiplegia and ten healthy adults participated in this study and walked at self-selected speeds on a GAITRite-instrumented carpet. The activities of the opposite shoulder girdle muscle including the latissimus dorsi, anterior deltoid, and posterior deltoid were simultaneously recorded using surface EMG during gait. They were randomly assigned a condition: without an arm sling, a single strap arm sling, a Harris hemi arm sling, a Rolyan humeral cuff arm sling, and a Bobath roll arm sling. The following gait variables were analyzed: the temporo-spatial parameters of velocity, step length, stride length, swing phase, stance phase, single support, step time and toe in/toe out. The statistical analysis was one-way ANOVA with repeated measures to compare the variation of each variable. In comparison of parameters in each trial in the hemiplegia group, the non-affected side stride length, single support, and toe in/toe out resulted in statistically significantly changes (p<.05). But without an arm sling group did not show any gait parameter differences with arm slings. This study found that several arm slings varied gait patterns in patients with hemiplegia and in healthy adults. In the EMG analysis, the Rolyan humeral cuff arm sling and the Bobath roll arm sling were higher muscle activity for the latissimus dorsi muscle than did the single strap ann sling. Further study should examine the problems that appeared in patients who worn arm slings by focusing on a larger number of subjects and by studying the variety of responses in more detail using an assessment tool that measures variation.

기존의 재래식 유탕팽화유과의 문제점을 개선하기 위하여 진공을 이용한 진공팽화기를 설계 제작하였다. 공정변수에 따른 진공팽화유과의 특성을 비교 분석하기 위하여 부피팽화율, 밀도, 절단강도, 색도, 미세구조를 측정하였다. 진공팽화기의 공정변수는 가열온도(100, 120, 140, 160, 180oC), 예열시간(0, 2, 4, 6, 8분), 진공팽화시간(5, 10, 15, 20분)이며, 가열온도 100oC, 예열시간 6분, 진공팽화시간 10분에서 진공팽화유과의 부피팽화율은 10.04로 가장 높게 측정되었고, 밀도는 0.15 g/cm3로 가장 낮게 측정되었지만, 부피팽화율 9.47, 밀도 0.16 g/cm3으로 측정된 가열온도 120oC, 예열시간 4분, 진공팽화시간 5분에서의 진공팽화유과가 유탕유과의 외관 및 조직과 가장 유사하였다. 절단강도는 가열온도 100oC, 예열시간 6분, 진공팽화시간 15분에서 140 g/cm2로 가장 낮게 측정되었다. 색도는 예열시간과 진공팽화시간이 증가함에 따라 백색도가 증가하는 경향을 보였고, 황색도는 감소하는 경향을 보였으며, 적색도는 유의적 차이가 없었다. 진공팽화유과의 백색도(L값)가 유탕팽화유과보다 25정도 높았으며, 적색도(a값)와 황색도(b값)는 유의적 차이는 보이지 않았으며, 진공팽화유과의 미세구조는 가열온도 120oC, 예열시간 4분, 진공팽화시간 5분에서 기공이 작고 균일하였다. 유탕팽화유과와 비교 시 절단강도는 유사하였으나, 부피팽화율은 낮았고, 밀도는 높았다. 셀이 균일하게 형성된 진공팽화의 미세구조와는 달리 유탕팽화유과의 미세구조는 표면과 내부층의 차이가 확인되었다. 진공팽화기의 최적 공정조건은 진공팽화유과의 품질을 고려 할 때, 가열온도 120oC, 예열시간 4분, 진공팽화시간 5분으로 판단되었다.

The purpose of this study was to identify the determinants of decision-making confidence of clothing. As determinants, this study examined consumer susceptibility to interpersonal influence, vanity, and clothing knowledge. Data were collected through surveying university students in Seoul metropolitan area using convenience sampling method. Out of 324 distributed, 300 useful questionnaires were returned. The results showed that identical conformity among consumer susceptibility to interpersonal influence factors significantly influences, both directly and indirectly, decision making confidence through vanity. Although normative conformity does not influence decision-making confidence directly, it does significantly influence decision-making confidence indirectly through influencing vanity and clothing knowledge. The results suggest clothing is a manifestation tool for managing public self, which finally leads to increased clothing knowledge and decision-making confidence of clothing. These findings may be used by marketers in developing strategies for product development and promotion.