According to the analysis of the Korean Radioactive Waste Society, saturation of nuclear power plant temporary storage is expected sequentially from 2031, and accordingly, the need for highlevel radioactive waste disposal facilities has emerged. In order to establish a repository for high-level radioactive waste, the performance and safety analysis of the repository must be conducted in compliance with regulatory requirements. For safety analysis, it needs a collection of arguments and evidence. and IAEA defined it as ‘Safety case’. The Systematic method, which derives scenarios by systematizing and combining possible phenomena around the repository, is widely used for developing Safety case. Systematic methods make use of the concept of Features, Events and Processes (FEP). FEP identifies features that affect repository performance, events that can affect a short period of time, and processes that can have an impact over a long period of time. Many countries, such as Finland, Sweden, Japan, United States, etc., are in process of licensing disposal facilities by using ‘Safety case’. And they then develop their own project-specified FEP lists and employ them for performing safety assessments. However, the systematic procedure for generating scenarios for safety evaluation is not clearly defined. According to the International Atomic Energy Agency (IAEA) Safety Standards Series (SSG- 23), the bottom-up method is an approach for conducting safety analysis using Features, Events, and Processes (FEPs). However, the process of how each FEP is utilized to establish a scenario for safety evaluation remains unclear. Additionally, there exists not only a bottom-up approach for generating scenarios using FEPs, but also a hybrid scenario development method that incorporates a top-down approach based on safety functions. Each country address scenario derivation in accordance with the adopted hybrid method. Nevertheless, a challenge arises in its application due to discrepancies between their approach and the hybrid approach specific which we are going on. Hence, this study introduces the FEP integration methodology for generating scenarios based on the hybrid scenario development method using the FEP list.

Raman characteristics of various minerals constituting natural rocks collected from uranium deposits in Okcheon metamorphic zone in Korea are presented. Micro-Raman spectra were measured using a confocal Raman microscope (Renishaw in Via Basis). The focal length of the spectrometer was 250 mm, and a 1800 lines/mm grating was installed. The outlet of the spectrometer was equipped with a CCD (1,024256 pixel) operating at -70°C. Three objective lenses were installed, and each magnification was 10, 50, and 100 times. The diameter of the laser beam passing through the objective lens and incident on the sample surface was approximately 2 m. The laser beam power at 532 nm was 1.6 mW on the sample surface. Raman signal scattered backward from the sample surface was transmitted to the spectrometer through the same objective lens. To accurately determine the Raman peak position of the sample, a Raman peak at 520.5 cm-1 measured on a silicon wafer was used as a reference position. Since quartz, calcite, and muscovite minerals are widely distributed throughout the rock, it is easy to observe with an optical microscope, so there is no difficulty in measuring the Raman spectrum. However, it is difficult to identify the uraninite scattered in micrometer sizes only with a Raman microscope. In this case, the location of uraninite was first confirmed using SEM-EDS, and then the sample was transferred to the Raman microscope to measure the Raman spectrum. In particular, a qualitative analysis of the oxidation and lattice conditions of natural uraninite was attempted by comparing the Raman properties of a micrometer-sized natural uraninite and a laboratory-synthesized UO2 pellet. Significantly different T2g/2LO Raman intensity ratio was observed in the two samples, which indicates that there are defects in the lattice structure of natural uraninite. In addition, no uranyl mineral phases were observed due to the deterioration of natural uraninite. This result suggests that the uranium deposit is maintained in a reduced state. Rutile is also scattered in micrometer-sizes, similar to uraninite. The Raman spectrum of rutile is similar in shape to that of uraninite, making them confused. The Raman spectral differences between these two minerals were compared in detail.

Long-term climate and surface environment changes can influence the geological subsurface environment evolution. In this context, a fluid flow pathway developing and connection possibility can be increased between the near-surface zone and deep depth underground. Thus, it is necessary to identify and prepare for the overall fluid flow at the entire geological system to minimize uncertainty on the spent nuclear fuel (SNF) disposal safety. The fluid flow outside the subsurface environment is initially penetrated through the surface and then the unsaturated area. Thus, the previously proved reports, POSIVA in Finland, suggested that sequential research about the fluid infiltration experiment (INEX) and the investigation is necessary. Characterizing the unsaturated zone can help predict changes and ensure the safety of SNFs according to geological long-term evolution. For example, the INEX test was conducted at the upper part of ONKALO, about 50 to 100 m depth, to understand the geochemical evolution of the groundwater through the unsaturated zone, to evaluate the main flow of groundwater that can approach the SNF disposal reservoir, and to estimate the decreasing progress of the buffering capacity along the pathway through the deep geological disposal. In the present study, a preliminary test was performed in the UNsaturated-zone In-situ Test (UNIT) facility near the KAERI underground research tunnel to design and establish a methodology for infiltration experiments consistent with the regional characteristics. The results represented the methodological application is possible for characterizing unsaturated-zone to perform infiltration experiments. The scale of the experiment will be expanded sequentially, and continuous research will be conducted for the next application.

The HADES (High-level rAdiowaste Disposal Evaluation Simulator) was developed by the Nuclear Fuel Cycle & Nonproliferation (NFC) laboratory at Seoul National University (SNU), based on the MOOSE Framework developed by the Idaho National Laboratory (INL). As an application of the MOOSE Framework, the HADES incorporates not only basic MOOSE functions, such as multi-physics analysis using Finite Element Method (FEM) and various solvers, but also additional functions for estimating the performance assessment of Deep Geological Repositories (DGR). However, since the MOOSE Framework does not have complex mesh generation and data analyzing capabilities, the HADES has been developed to incorporate these missing functions. In this study, although the Gmsh, finite element mesh generation software, and Paraview, finite element analysis software, were used, other applications can be utilized as well. The objectives of HADES are as follows: (i) assessment of the performance of a Spent Nuclear Fuel (SNF) disposal system concerning Thermal-Hydraulic-Mechanical-Chemical (THMC) aspects; (ii) Evaluation of the integrity of the Engineered Barrier System (EBS) of both general and high-efficiency design perspective; (iii) Collaboration with other researchers to evaluate the disposal system using an open-source approach. To achieve these objectives, performance assessments of the various disposal systems and BMTs (BenchMark Test), conducted as part of the DECOVALEX projects, were studied regarding TH behavior. Additionally, integrity assessments of various DGR systems based on thermal criteria were carried out. According to the results, HADES showed very reasonable results, such as evolutions and distributions of temperature and degree of saturation, when compared to validated code such as TOUGH-FLAC, ROCMAS, and OGS (OpenGeoSys). The calculated data are within the range of estimated results from existed code. Furthermore, the first version of the code, which can estimate the TH behavior, has been prepared to share the contents using Git software, a free and open-source distribution system.

Uranium (U) is a hazardous material that can lead to both chemical and radiological toxicity, including kidney damage and health issues associated with radiation exposure. In South Korea. In Korea, where shallow weathered granitic aquifers are widespread, several previous studies have reported high levels of radioactivity in shallow groundwater. This ultimately led to the closure of 60 out of 4,140 groundwater production wells in South Korea. In this study, we examined aquifers currently dedicated to drinking water supply and investigated a dataset of 11,225 records encompassing 103 environmental parameters, based on the random forest classifier. This dataset comprises 80 physical parameters associated with the hydraulic system and 23 chemical parameters linked to water-rock interactions. Among the hydraulic parameters, the presence of a coarse loamy texture in the subsoil displayed a notable positive relationship with the concentration of uranium, implying that it plays a significant role in forming redox conditions for the leaching of uranium from host rocks. Fluorine (F), a major product of water-rock interaction in granitic aquifers, exhibited a positive correlation with the distribution of uranium concentrations. The positive relationship between F concentration and uranium levels suggests that the dissolved uranium originates from groundwater interacting with granites. In conclusion, our findings indicate that two key factors, namely the infiltration capacity of soil layers and the aqueous speciation in groundwater resulting from interactions with local solids, play important roles in determining uranium concentrations in granitic aquifers.

The design and fabrication of suitable waste forms with high thermal and structural stability are essential for the safe management and disposal of radioactive wastes. In particular, the thermal properties and temperature distribution of waste form containing high heat-generating nuclides such as Cs and Sr can be used to evaluate its thermal stability, but also provide useful information for the design of canisters, storage systems, and repositories. In this study, a new program code-based thermal analysis framework has been developed to facilitate the characterization, design, and optimization of the waste form. Matlab was used as a software development platform because it provides powerful mathematical computation and visualization components such as the partial differential equation (PDE) toolbox for solving heat transfer problems using finite element method, the App Designer for graphical user interface (GUI), and the MATLAB Compiler for sharing MATLAB programs as standalone applications and web applications. The thermal analysis results such as temperature distribution, heat flux, maximum/ minimum temperature, and centerline/surface temperature profile are visualized with graphs and tables. To evaluate the effectiveness of the developed program, several design and optimization studies were carried out for the SrTiO3 waste form, selected as a stable form of strontium nuclide.

Recently, as carbon-neutral energy sources become increasingly important worldwide, SMRs (Small Modular Reactors), which offer significantly enhanced safety, versatility, and mobility compared to conventional nuclear reactors, are gaining attention as a viable alternative. SMR generally refers to small modular reactors with a power output of 300 MWe or less. Unlike conventional reactors, SMRs are characterized by an all-in-one design where peripheral systems and equipment are all integrated into the reactor itself, leading to enhanced reliability and durability. Additionally, the nuclear fuel reloading cycle is significantly extended compared to traditional reactors, resulting in a substantial reduction in maintenance difficulty and costs. Researchers have taken note of these characteristics of SMRs, particularly the extended fuel reloading cycle. Therefore, we have initiated the initial design of an ultra-small Micro Modular Reactor with an electricity generation capacity of 10 MWe and a fuel cycle of up to 55 years, with the goal of using it as a propulsion power source for various transportation modes, especially ships. Our design of MMR, called ‘ARA,’ is primarily distinguished by its use of U233 and Th232 fuels instead of conventional UO2 fuel. Due to various features of ‘ARA,’ including different fuel compositions, ARA is predicted to exhibit several characteristic features compared to conventional PWRs. In this study, among these characteristics, we focused on predicting changes in material composition within the fuel rod during the extended cycle operation of high-enriched fuel, rather than short-cycle operation using low-enriched fuel, unlike conventional reactors. The primary goal of this research is to observe the behavior of the composition of the materials used in the fuel cycle of the MMR, which utilizes U233 and Th232 fuels instead of UO2. Considering the difficulties in the spent nuclear fuel disposal process, many different trials were made to minimize the fission products of ARA, which differs from conventional reactors in terms of fuel type, size, and fuel cycle, in relation to waste generation.

The objective of this study is development of graphite-boron composite material as a replacement for metal canisters to Improve the heat dissipation and radiation shielding performance of dry spent nuclear fuel storage system and reduce the volume of waste storage system. KEARI research team plan to use the graphite matrix manufacturing technology to pelletize the graphite matrix and adjust the content of phenolic resin binder to minimize pore formation. Specifically, we plan to adjust the ratio of natural and synthetic graphite powder and use uniaxial pressing technology to manufacture black graphite matrix with extremely high radial thermal conductivity. After optimizing the thermal conductivity of the graphite matrix, we plan to mix it with selected boron compounds, shape it, and perform sintering and purification heat treatments at high temperatures to manufacture standard composite materials.

The nuclide management process for reducing the environmental burden being developed by the Korea Atomic Energy Research Institute is performed in molten salts, resulting in contaminated salt wastes containing fission products such as Cs, Sr, Ba, and rare-earth nuclides. In addition, the spent fuel of a molten salt reactor (MSR) contains a variety of fission products, and a purification process may be required for the reuse of the salt and the separation and disposal of the fission products in the spent nuclear fuel. The melt-crystallization method is a technique used for the purification and separation of chemicals or metals based on the different melting points of the different substances. In a recent study, our group developed a reactive-crystallization method using Li2CO3 precipitation agent to precipitate metal corrosion from the reactor through a chlorination reaction by HCl and Cl2, which may occur in chloride molten salt, and successfully precipitated the metal precipitate and purified and recovered LiCl salt. In this study, reactive-crystallization method has been established for removing fission products and corrosive materials. Using the reactive crystallization method, white LiCl-KCl salt that was not discolored by metal corrosion was recovered through the crystallization plates, and fission products and metal elements were shown to be suppressed to several ppm in the purified salt. Consequently, high-purity salts were recovered with high nuclide and corrosive separation efficiencies. The reactive crystallization procedure can also be applied to other salt waste systems, such as MSR nuclear fuel treatment and molten salt chemistry for the elimination of corrosive substances.

For safe and economical spent fuel management, assessing the integrity of the cladding, which is the first barrier to the escape of radioactive material, is very important. For the sake of risk assessment, it is essential to calculate the probability of failure of the spent fuel rods loaded inside the cask during the transportation or storage. However, due to the large amounts of calculations required, it is not practical to analyze every detail of the spent fuel rods and assemblies. This study presents a methodology to perform a cask-level analysis by sequentially simplifying the fuel rods and spent fuel assemblies for the calculation of fuel rod failure probability. A simplified single fuel rod model was generated by considering the material properties of a high burnup fuel rod stored in dry storage for approximately 5 years and the interfacial bonding conditions of the cladding tube. The simplified model produces the same deflection as the detailed model at the critical moment that produces a fracture plastic strain of 1%. The developed single fuel rod simplified model is assembled in a CE 16×16 configuration, and a methodology is presented in which the CE 16×16 assembly model is once again replaced by a simplified model with a cuboidal shape. Compression analyses were performed on each part of the CE 16×16 model to obtain isotropic property data, and a simplified model was created based on those data and the cross-sectional second moment values of the parts. A cask drop analysis was performed to validate the similarity of the CE 16×16 model and the simplified model by comparing important structural responses such as impact acceleration. The 20 simplified fuel assembly models and one detailed model were loaded into a cask to perform the drop analysis. For the detailed model, the impact acceleration was extracted for different loading positions and the corresponding impact load and pinch load were derived. The spring force and contact force corresponding to the pinch load were extracted by applying a Python script technique to extract the maximum value of them exerted on each fuel rod. The vulnerability of spent fuel rods to bending loads and the failure criteria were considered during the simplification process of a single fuel rod. From the extracted impact and pinch loads, the probability of failure of the spent fuel rods as a function of impact acceleration can be calculated.

In the 3rd revision of NUREG-0800, which was revised in 2007, the calculation method for decay heat in the design of the Ultimate Heat Sink (UHS) for a pressurized water reactor is recommended to be based on the ANSI/ANS-5.1 method. This method employs a more complex decay heat calculation formula compared to the one introduced in Branch Technical Position ASB 9-2, which was presented in the 2nd revision. While most of the variables for decay heat calculation in ANSI/ANS-5.1 can be inferred from the methods outlined in the appendices, determining the fractions of fission products is not straightforward despite their significant impact on the results. When reviewing documents that evaluate decay heat using the ANSI/ANS-5.1 method, it is observed that they often adopt a conservative approach by assuming that the fraction of the most influential fission product is 100%. In this study, the fractions of each fission product presented in LLNL’s 2016 report were used to calculate decay heat, and the results were compared with the ASB 9-2 method and ORIGEN code results. The comparison showed that ANS 5.1 tends to yield higher decay heat values than ANS 9-2, particularly at the reference time of 1M seconds, while ORIGEN-ARP generally produced lower values. Therefore, it is concluded that even when using the ANSI/ANS-5.1 method with the fractions of each fission product for decay heat calculations in spent nuclear fuel wet or dry storage facility assessments, it provides a sufficiently conservative thermal evaluation.

Ring Tensile Test (RTT) is mainly performed for comparing tensile strength and total strain between nuclear fuel cladding specimens under various initial conditions. Through RTT, the loaddisplacement (F-D) curve obtained from the uniaxial tensile test can also be obtained. However, the Young’s modulus estimated from the gradient of the straight portion is much lower than general value of materials. The reasons include tensile machine compliance, slack in the fixtures, or elastic deformation of the fixtures and the tooling. Another reason is that the bending of the test part in the ring is stretched with two pieces of tools. Although the absolute value of the Young’s modulus is smaller than the actual value, it is applicable to calculate the ratio of the Young’s moduli of different materials, that is, the relative value. The Young’s modulus, or slope of the linear section, varies slightly depending on which location data is used and how much data is included. In order to obtain a more accurate ratio of Young’s moduli between materials using the RTT results, a post-processing method for the ring tensile test results that can prevent such human errors is proposed as follows. First, the slope of the linear section is obtained using the displacement and load when the load increase is the largest and the displacement and load of the position that is 95% of the maximum load increase. To replace the section where the ring-shaped specimen is stretched at the beginning of the F-D curve, a straight line equal to the slope of the linear section is drawn to the displacement axis from the position of maximum load increase and moved to the origin to obtain the final F-D curve for a RTT. Lastly, the yield stress uses the stress at the point where the 0.2% offset straight line and the F-D curve meet as suggested in the ASTM E8/E8M-11 “Standard test methods for tensile testing of metallic materials”. RTT results post-processing method was coded using FORTRAN language so that it could be performed automatically. In addition, sensitivity analysis of the included data range on the Young’s modulus was performed by using the included data range as 90%, 85%, and 80% of the maximum load increase.

Considering the domestic situation where all nuclear power plants are located on seaside, the interim storage site is also likely to be located on coastal site. Maritime transportation is inevitable and the its risk assessment is very important for safety. Currently, there is no independently developed maritime transportation risk assessment code in Korea, and no research has been conducted to evaluate the release of radioactive waste due to the immersion of transport cask. Previous studies show that the release rate of radionuclides contained in a submerged transport cask is significantly affected by the area of flow path generated at the breached containment boundary. Due to the robustness of a cask, the breach is the most likely generated between the lid and body of cask. CRIEPI investigated the effect of cask containment on the release rate of radioactive contents into the ocean and proposed a procedure to calculate the release rate considering the socalled barrier effect. However, the contribution of O-ring on the release rate was not considered in the work. In this study, test and analysis is performed to determine the equivalent flow path gap considering the influence of O-rings. These results will be implemented in the computational model to assess sea water flow through a breached containment boundary using CFD techniques to assess radionuclide release rates. To evaluate the release rate as a function of lid displacement, a small containment vessel is engineered and a metal O-ring of the Helicoflex HN type is installed, which is the most commonly used one in transport and storage casks. The lid of containment vessel is displaced in vertical and horizontal direction and the release rate of the vessel was quantified using the helium leak test and the pressure drop test. Through this work, the relationship between the vertical opening displacement and horizontal sliding displacement of the cask lid and the actual flow path area created is established. This will be implemented in the CFD model for flow rate calculation from a submerged transport cask in the deep sea. In addition, the compression of the O-ring causes very small gaps, such as capillaries. In these cases, Poiseuille’s law is used to calculate the capillary flow rate.

The solid-state chemistry of uranium is essential to the nuclear fuel cycle. Uranyl nitrate is a key compound that is produced at various stages of the nuclear fuel cycle, both in front-end and backend cycles. It is typically formed by dissolving spent nuclear fuel in nitric acid or through a wet conversion process for the preparation of UF6. Additionally, uranium oxides are a primary consideration in the nuclear fuel cycle because they are the most commonly used nuclear fuel in commercial nuclear reactors. Therefore, it is crucial to understand the oxidation and thermal behavior of uranium oxides and uranyl nitrates. Under the ‘2023 Nuclear Global Researcher Training Program for the Back-end Nuclear Fuel Cycle,’ supported by KONICOF, several experiments were conducted at IMRAM (Institute of Multidisciplinary Research for Advanced Materials) at Tohoku University. First, the recovery ratio of uranium was analyzed during the synthesis of uranyl nitrate by dissolving the actual radioisotope, U3O8, in a nitric acid solution. Second, thermogravimetric-differential thermal analysis (TG-DTA) of uranyl nitrate (UO2(NO3)2) and hyper-stoichiometric uranium dioxide (UO2+X) was performed. The enthalpy change was discussed to confirm the mechanism of thermal decomposition of uranyl nitrate under heating conditions and to determine the chemical hydrate form of uranyl nitrate. In the case of UO2+X, the value of ‘x’ was determined through the calculation of weight change data, and the initial form was verified using the phase diagram for the U-O system. Finally, the formation of a few UO2+X compounds was observed with heat treatment of uranyl nitrate and uranium dioxide at different temperature intervals (450°C-600°C). As a result of these studies, a deeper understanding of the thermal and chemical behavior of uranium compounds was achieved. This knowledge is vital for improving the efficiency and safety of nuclear fuel cycle processes and contributes to advancements in nuclear science and technology.

Since the Fukushima nuclear accident in 2011, the development of accident tolerant fuel (ATF) has been actively pursued as an alternative to improve the safety of nuclear power plants. In addition, nuclear power plants containing ATF have recently been included as green energy in the 2022 EU taxonomy bill, receiving a lot of attention. Many countries are considering increasing 235U enrichment from 5 to 10 235U % for higher burnup and long cycle operation with ATF improving safety. To utilize ATF, the applicability of fuel storage systems such as new fuel storage vault, Region 1, and Region 2 must be determined. The purpose of this paper is to confirm the applicability of applying ATF, which is being developed in Korea, to the nuclear fuel storage system of Korean nuclear power plants. The nuclear power plant model used in the analysis is APR-1400, a representative Korean nuclear power plant model, and ATF model used in the analysis is Mo microcell UO2 pellet with CrAl coating, which is being developed in Korea. MCNP 6.2 has been used for multiplication factor calculations, and the TRITON/NEWT and ORIGEN-S modules of the SCALE code have been used for depletion calculations. From the analysis results, solutions and additional analysis would be necessary to satisfy criticality regulatory requirements to utilize ATF with increased enrichment.

To address the pressing societal concern in Korea, characterized by the imminent saturation of spent nuclear fuel storage, this study was undertaken to validate the fundamental reprocessing process capable of substantially mitigating the accumulation of spent nuclear fuel. Reprocessing is divided into dry processing (pyro-processing) and wet reprocessing (PUREX). Within this context, the primary focus of this research is to elucidate the foundational principles of PUREX (Plutonium Uranium Redox Extraction). Specifically, the central objective is to elucidate the interaction between uranium (U) and plutonium (Pu) utilizing an organic phase consisting of tributyl phosphate (TBP) and dodecane. The objective was to comprehensively understand the role of HNO3 in the PUREX (Plutonium Uranium Redox Extraction) process by subjecting organic phases mixed with TBPdodecane to various HNO3 concentrations (0.1 M, 1.0 M, 5.0 M). Subsequently, the introduction of Strontium (Sr-85) and Europium (Eu-152) stock solutions was carried out to simulate the presence of fission products typically contented in the spent nuclear fuel. When the operation proceeds, the complex structure takes the following form. 􀜷􀜱􀬶 􀬶􀬾(􀜽􀝍) + 2􀜰􀜱􀬷 􀬿(􀜽􀝍) + 2􀜶􀜤􀜲(􀝋􀝎􀝃) ↔ 􀜷􀜱􀬶(􀜰􀜱􀬷)􀬶 ∙ 2􀜶􀜤􀜲(􀝋􀝎􀝃) Subsequently, separate samples were gathered from both the organic and aqueous phases for the quantification of gamma-rays and alpha particles. Alpha particle measurements were conducted utilizing the Liquid Scintillation Counter (LSC) system, while gamma-ray measurements were carried out using the High-Purity Germanium Detector (HPGe). The distribution ratio for U, Eu (Eu-152), and Sr (Sr-84) was ascertained by quantifying their activity through LSC and HPGe. Through the experiments conducted within this program, we have gained a comprehensive understanding of the selective solvent extraction of actinides. Specifically, uranium has been effectively separated from the aqueous phase into the organic phase using a combination of tributyl phosphate (TBP) and dodecane. Subsequently, samples containing U(VI), Eu(III), and Sr(II) underwent thorough analysis utilizing LSC and HPGe detectors. Our radiation measurements have firmly established that the concentration of nitric acid enhances the selective separation of uranium within the process.

The International Atomic Energy Agency (IAEA) Safety Fundamentals No. SF-1 Safety Principle 7 states that people and the environment, present and future, must be protected against radiation risk. Therefore, it is important to evaluate the safety of radioactive waste repositories on a longterm time scale to ensure future safety. However, IAEA-TECDOC-767 states that the long-term time scale of interest means that the risk or dose to future individuals cannot be reliably predicted because it relies on assumptions. Therefore, evaluating the safety of long-term time scales should use safety indicators that are less dependent on assumptions. Radiotoxicity is one of the safety indicators that represent an inherent risk from radioactive waste. It has been mainly used to show the time required until the hazard presented by waste decreases to that of natural uranium ore and is easy to use in communication with the public. There are several methods for calculating Radiotoxicity. Radioactivity is multiplied by a Dose Conversion Factor (DCF) to be expressed in Sv units, or radioactivity be divided into Maximum Permissible Concentration (MPC) to be expressed in m3 units as the amount of water needed to dilute the radionuclide to the permitted level. It is also often made dimensionless through comparison with reference materials like uranium ore. Radiotoxicity varies in size several times, even if it is a waste of similar origins and components, depending on the Radiological variable (e.g., Annual Limitation Intake (ALI), Dose Conversion Factor (DCF), Maximum Permissible Concentration (MPC), Activity). Therefore, this study was conducted to determine whether there was a significant difference when different radiological variables were substituted. This study compares and analyzes their differences using various MPCs or DCFs used in each country. In addition, this study analyzes radionuclides that influence radiotoxicity with several radiological variables. This study introduces the effects of substituting different radiological variables.

International Atomic Energy Agency defines the term “Poison” as a substance used to reduce reactivity, by virtue of its high neutron absorption cross-section, in IAEA glossary. Poison material is generally used in the reactor core, but it is also used in dry storage systems to maintain the subcriticality of spent fuel. Most neutron poison materials for dry storage systems are boron-based materials such as Al-B Carbide Cermet (e.g., Boral®), Al-B Carbide MMC (e.g., METAMIC), Borated Stainless Steel, Borated Al alloy. These materials help maintain subcriticality as a part of the basket. U.S.NRC report NUREG-2214 provides a general assessment of aging mechanisms that may impair the ability of SSCs of dry storage systems to perform their safety functions during longterm storage periods. Boron depletion is an aging mechanism of neutron poison evaluated in that report. Although that report concludes that boron depletion is not considered to be a credible aging mechanism, the report says analysis of boron depletion is needed in original design bases for providing long-term safety of DSS. Therefore, this study aimed to simulate the composition change of neutron poison material in the KORAD-21 system during cooling time considering spent fuel that can be stored. The neutron source term of spent fuel was calculated by ORIGEN-ARP. Using that source term, neutron transport calculation for counting neutrons that reach neutron poison material was carried out by MCNP®-6.2. Then, the composition change of neutron poison material by neutron-induced reaction was simulated by FISPACT-II. The boron-10 concentration change of neutron poison material was analyzed at the end. This study is expected to be the preliminary study for the aging analysis of neutron poison material about boron depletion.

In nuclear fuel development research, consideration of the back-end cycle is essential. In particular, a review of an in-reactor performance of nuclear fuel related to the various degradation phenomena that can occur during spent fuel dry storage is an important area. The important factors affecting the degradation of zirconium-based cladding during dry storage are the cladding’s hydrogen concentration and rod internal pressure after irradiation. In this study, a preliminary analysis of the in-reactor behavior of the HANA cladding, which has been developed and is currently undergoing licensing review, was performed, and based on this result, a comparative analysis between nuclear fuel with HANA cladding and current commercial fuel under storage conditions was performed. The results show that the rod internal pressure of nuclear fuel with HANA cladding is not significantly different from that of commercial cladding, and the hydrogen concentration in the cladding tends to reduce due to the increased corrosion resistance, so fuel integrity in a dry storage conditions is not expected to be a major problem. Although the lack of cladding creep data under dry storage conditions, the results from the Halden research reactor test comparing in-reactor creep behavior with Zircaloy-4 showed that there is sufficient margin for degradation due to creep during storage.

EU taxonomy requires to solve problems for safe management of radioactive waste and disposal of spent fuel, which is a precondition for growing demand for nuclear power plant. Currently, Korea manages about 18,000 tons of high-level radioactive waste at temporary storage facilities in nuclear power plant sites, but such temporary storage facilities are expected to become saturated sequentially from 2031. Therefore, it is necessary to secure a permanent disposal facility to safely treat high-level radioactive waste. In accordance with the second basic plan for high-level radioactive waste management in 2021, it is necessary to establish requirements for regulatory compliance for the site selection and site acquisition, investigation and evaluation, and construction for the establishment of a deep geological disposal facility. In this study, we analyzed the regulatory policies and cases of leading foreign countries related to deep geological disposal facilities for high-level radioactive waste disposal waste such as IAEA, USA, Sweden, and Finland using data analysis methodology. To analyze a large amount of textbased document data, text mining is applied as a major technology and a verification standard that secures validity and safety based on the regulatory laws described so far is developed to establish a regulatory base suitable for domestic deep geological disposal status. Based on the collected data, preprocessing and analysis with Python were performed. Keywords and their frequency were extracted from the data through keyword analysis. Through the measured frequency values, the contents of the objects and elements to be regulated in the statutory items were grasped. And through the frequency values of words co-occurring among different sections through the analysis of related words, the association was obtained, and the overall interpretation of the data was performed. The results of analyzing regulations of major foreign countries using text mining are visualized in charts and graphs. Word cloud can intuitively grasp the contents by extracting the main keywords of the contents of the regulations. Through the network connection graph, the relationship between related words can be visually structured to interpret data and identify the causal relationship between words. Based on the result data, it is possible to compare and analyze the factors to be supplemented by analyzing domestic nuclear safety case and regulations.