The most important thing in development of a process-based TSPA (Total System Performance Assessment) tool for large-scale disposal systems (like APro) is to use efficient numerical analysis methods for the large-scale problems. When analyzing the borehole in which the most diverse physical phenomena occur in connection with each other, the finest mesh in the system is applied to increase the analysis accuracy. Since thousands of such boreholes would be placed in the future disposal system, the numerical analysis for the system becomes significantly slower, or even impossible due to the memory problem in cases. In this study, we propose a tractable approach, so called global-local iterative analysis method, to solve the large-scale process-based TSPA problem numerically. The global-local iterative analysis method goes through the following process: 1) By applying a coarse mesh to the borehole area the size of the problem of global domain (entire disposal system) is reduced and the numerical analysis is performed for the global domain. 2) Solutions in previous step are used as a boundary condition of the problem of local domain (a unit space containing one borehole and little part of rock), the fine mesh is applied to the borehole area, and the numerical analysis is performed for each local domain. 3) Solutions in previous step are used as boundary conditions of boreholes in the problem of global domain and the numerical analysis is performed for the global domain. 4) steps 2) and 3) are repeated. The solution derived by the global-local iterative analysis method is expected to be closer to the solution derived by the numerical analysis of the global problem applying the fine mesh to boreholes. In addition, since local problems become independent problems the parallel computing can be introduced to increase calculation efficiency. This study analyzes the numerical error of the globallocal iterative analysis method and evaluates the number of iterations in which the solution satisfies the convergence criteria. And increasing computational efficiency from the parallel computing using HPC system is also analyzed.

The timescale of safety assessment for a geological disposal system is considered up to hundreds of thousands of years when the radionuclides in spent nuclear fuel decay to levels comparable to natural radioactivity. During this long period, a variety of climate changes are expected to occur, including variations in temperature and precipitation as well as long-term sea level changes and glacial cycles. These climate changes can either directly affect water balance components or indirectly affect water balance by altering terrain and vegetation that have an impact on water balance. Water balance is a significant element of safety assessment, because it affects the radionuclide transport via groundwater flow, which in turn affects the radiological risk to humans and other biotas. Therefore, it is important to understand the hydrologic response to climate changes for proving the long-term safety of the disposal system. To this end, this study performed hydrological simulations using the SWAT (Soil and Water Assessment Tool) for several climate change scenarios. SWAT is the watershed-scale hydrological model developed by the USDA-ARS (United States Department of Agriculture - Agricultural Research Service) and has been widely used to quantify the water balance in a watershed. It calculates the hydrologic cycle based on the water balance equation with different physical processes for water balance components such as evapotranspiration, surface runoff, and groundwater recharge. This study assumed several climate change scenarios (e.g., variations in temperature and precipitation, sea level change, and formation of permafrost) and analyzed how the components of the water balance would respond under different scenarios and which scenarios would have the greatest impact on the water balance. These findings can provide valuable insights for future long-term safety assessments on the Korean Peninsula and can also be used as input data for the biosphere module of APro (Adaptive process-based total system performance assessment framework).

Since high-level radioactive wastes contain long-lived nuclides and emit high energy, they should be disposed of permanently through a deep geological disposal system. In Korea, the first (2016.07) and the second (2021.12) basic plans for the management of high-level disposal systems were proposed to select sites for deep geological disposal facilities and to implement business strategies. Leading countries such as Finland, Sweden and France have developed and applied safety cases to verify the safety of deep geological disposal systems. By examining the regulatory status of foreign leading countries, we analyze the safety cases ranging from the site selection stage of the deep geological disposal system to the securing of the permanent disposal system to the investigation, analysis, evaluation, design, construction, operation, and closure. Based on this analysis, we will develop safety case elements for long-term safety of deep geological disposal systems suitable for domestic situation. To systemically analyze data based on safety cases, we have established a database of deep geological disposal system regulations in leading foreign countries. Artificial intelligence text mining and data visualization techniques are used to provide database in dashboard form rather than simple lists of data items, which is a limitation of existing methods. This allows regulatory developers to understand information more quickly and intuitively and provide a convenient interface so that anyone can easily access the analyzed data and create meaningful information. Furthermore, based on the accumulated bigdata, the artificial intelligence learns and analyzes the information in the database through deep learning, and aims to derive a more accurate safety case. Based on these technologies, this study analyzed the legal systems, regulatory standards, and cases of major international leading countries and international organizations such as the United States, Sweden, Finland, Canada, Switzerland, and the IAEA to establish a database management system. To establish a safety regulation base suitable for the domestic deep geological disposal environment, the database is provided as data to refer to and apply systematic information management on regulatory standards and regulatory cases of overseas leading countries, and it is expected that it will play a key role as a forum for understanding and discussing the level of safety of deep geological disposal system among stakeholders.

The engineered barrier system (EBS) is an indispensable element of a deep geological repository (DGR) designed to prevent the discharge of radioactive materials into the environment. The buffer material is a vital component of the EBS by creating a physical and chemical barrier that prevents the migration of radioactive materials. In the disposal environment, gases can be generated from the corrosion of the canister. When the gas generation rate exceeds the diffusion rate, the buffer material’s performance can deteriorate by the physical damage induced by the increase in pore pressure. Therefore, understanding the EBS’s behavior under gas generation conditions is crucial to guarantee the longterm safety and performance of the DGR. Lab-scale and field-scale experiments have been conducted to examine the stability of the buffer material concerning gas generation and movement by the previous researchers. To evaluate long-term stability for more than 100,000 years, it is essential to assess stability using a numerical model verified by these experiments. This study investigated the effect of interfacial characteristics on the numerical modeling accuracy of experimental simulation while verifying a numerical model through field-scale experimental results. The findings of this study are expected to furnish fundamental data for establishing numerical analysis guidelines for the longterm stability assessment of disposal systems.

To conduct numerical simulation of a disposal repository of the spent nuclear fuel, it is necessary to numerically simulate the entire domain, which is composed on numerous finite elements, for at least several tens of thousands of years. This approach presents a significant computational challenge, as obtaining solutions through the numerical simulation for entire domain is not a straightforward task. To overcome this challenge, this study presents the process of producing the training data set required for developing the machine learning based hybrid solver. The hybrid solver is designed to correct results of the numerical simulation composed of coarse elements to the finer elements which derive more accurate and precise results. When the machine learning based hybrid solver is used, it is expected to have a computational efficiency more than 10 times higher than the numerical simulation composed of fine elements with similar accuracy. This study aims to investigate the usefulness of generating the training data set required for the development of the hybrid solver for disposal repository. The development of the hybrid solver will provide a more efficient and effective approach for analyzing disposal repository, which will be of great importance for ensuring the safe and effective disposal of the spent nuclear fuel.

With the increasing demand for a repository to safely dispose of high-level radioactive waste (HLW), it is imperative to conduct a safety assessment for HLW disposal facilities for ensuring the permanent isolation of radionuclides. For this purpose, the Korea Atomic Energy Research Institute (KAERI) is currently developing the Adaptive Process-based total system performance assessment framework for a geological disposal system (APro). A far-field module, which specifically focuses on fluid flow and radionuclide transport in the host rock, is one of several modules comprising APro. In Korea, crystalline rock is considered the host rock for deep geological disposal facilities due to its high thermal conductivity and extremely low permeability. However, the presence of complex fracture system in crystalline rock poses a significant challenge for managing fluid flow and nuclide transport. To address this challenge, KAERI is participating in DECOVALEX-2023 Task F1, which seeks to compare and verify modeling results using various levels of performance assessment models developed by each country for reference disposal systems. Through the benchmark problems suggested by DECOVALEX-2023 Task F1, KAERI adopts the Discrete Fracture-Matrix (DFM) as the primary fracture modeling approach. In this study, the transport processes of reactive tracers in fractured rock, modeled with DFM, are simulated. Specifically, three different tracers (conservative, decaying, adsorbing) are introduced through the fracture under identical injecting conditions. Thereafter, the breakthrough curves of each tracer are compared to observe the impact of reactive tracers on nuclide transport. The results of this study will contribute to a better understanding of nuclide behavior in subsurface fractured rock under various conditions.

The development of Features, Events, and Processes (FEPs) and scenarios, which consider the longterm evolution of repository, is underway, along with the construction of input data and a model database for the adaptive process-based total system performance assessment framework, APro. PAPiRUS serves as an integrated information processing platform, enabling users to seamlessly access, search, and extract essential information. To enhance data usability, it is crucial to establish well-structured metadata for each dataset. Regarding FEPs, individual FEPs consist of extensive text-based data and sets of other short textual data. To enhance the searchability of these FEPs, precise keywords must be assigned to each FEP. For user convenience, the PAPiRUS FEP database contains several FEPs not only the long-term evolution FEPs developed by KAERI but also thousands of FEPs form the databases such as NEA PFEPs and Posiva FEPs. Generating keywords for thousands of FEPs proves to be a labor-intensive task. Consequently, this study explores natural language processing techniques for keyword analysis to boost the productivity of the keyword generation process. Specifically, we employ Generative Pretrained Transformer (GPT) models for keyword extraction. Our test results for keyword extraction demonstrate that, although not flawless, providing suitable prompts yields sufficiently useful keyword sets. We identified several optimal prompts and developed an Excel-based program to derive keywords from the existing FEP database using these prompts. By using the outcomes of this study, initial versions of keyword sets for thousands of FEPs can be rapidly produced and subsequently refined through expert review and editing. The generated keywords will serve as metadata within PAPiRUS.

The Korean Nuclear Safety and Security Commission has established a general guideline for the disposal of high-level waste, which requires that radiological effects from a disposal facility should not exceed the regulatory safety indicator, a radiological risk. The post-closure safety assessment of the disposal facility aims to evaluate the radiological dose against a representative person, taking into account nuclide transport and exposure pathways and their corresponding probabilities. The biosphere is a critical component of radiation protection in a disposal system, and the biosphere model is concerned with nuclide transport through the surface medium and the doses to human beings due to the contaminated surface environment. In past studies by the Korea Atomic Energy Research Institute (KAERI), the biosphere model was constructed using a representative illustration of surface topographies and groundwater conditions, assuming that the representative surface environment would not change in the future. Each topography was conceptualized as a single compartment, and distributed surface contamination over the geometrical domain was abstracted into 0D. As a result, the existing biosphere model had limitations, such as a lack of quantitative descriptions of various transport and exposure pathways, and an inability to consider the evolution of the surface environment over time. These limitations hinder the accurate evaluation of radiological dose in the safety assessment. To overcome these limitations, recent developments in biosphere modeling have incorporated the nuclide transport process over a 2D or 3D domain, integrating the time-dependent evolution of the surface environment. In this study, we reviewed the methodology for biosphere modeling to assess the radiological dose given by distributed surface contamination over a 2D domain. Based on this review, we discussed the model requirements for a numerical module for biosphere dose assessment that will be implemented in the APro platform, a performance assessment tool being developed by the KAERI. Finally, we proposed a conceptual model for the numerical module of dose assessment.

Since spent nuclear fuel (SNF) should be isolated from the human life zone for at least 106 years, deep geological disposal (DGD) is considered a strong candidate for SNF management in many countries. Therefore, a disposal canister should be nearly immune to corrosion in such a long-term storage environment. Even though copper has a low corrosion rate of a few millimeters per million years in geological environments, the corrosion resistance of the copper welds must be preferentially validated, which inevitably occurs during the sealing of the disposal canister after the SNF is loaded. This is because the weld zone is a discontinuous area of microstructure, which can accelerate uniform and localized corrosion. In this study, the microstructural characteristics of copper welds in different welding conditions such as friction stir welding, electron beam welding, cold spray, were analyzed, focusing on the formation of microstructure, which affects resistance to corrosion. In addition, the microstructure and corrosion properties of the copper weld zone manufactured by recent wire-based additive manufacturing (AM) technology were experimentally evaluated. From this preliminary test result, it was found that the corrosion characteristics of the welds produced by the AM process using wire are comparable to those of the conventional forged copper plate.

Geologic disposal at deep depth is an acceptable way to dispose of high-level radioactive waste and isolate it from the biosphere. The geological repository system comprises an engineered barrier system (EBS) and the host rock. The system aims to delay radionuclide migration through groundwater flow, and also, the flow affects the saturation of the bentonite in the EBS. The thermal conductivity of bentonite is a function of saturation, so the temperature in the EBS is directly related to the flow system. High-temperature results in the two-phase flow, and the two-phase flow system also affects the flow system. Therefore, comprehending the influencing parameters on the flow system is critical to ensure the safety of the disposal system. Various studies have been performed to figure out the complex two-phase flow characteristics, and numerical simulation is considered an effective way to predict the coupled behavior. DECOVALEX (DEvelopment of COupled models and their VALidation against EXperiments) is one of the most famous international cooperating projects to develop numerical methods for thermo-hydro-mechanicalchemical interaction, and Task C in the DECOVALEX-2023 has the purpose of simulating the Fullscale Emplacement (FE) experiment at the Mont-Terri underground research laboratory. We used OGS-FLAC, a self-developed numerical simulator combining OpenGeoSys and FLAC3D, for the simulation and targeted to analyze the effecting parameters on the two-phase flow system. We focused on the parameters of bentonite, a key component of the disposal system, and analyzed the effect of compressibility and air entry pressure on the flow system. Compressibility is a parameter included in the storage term, defining the fluid storage capacity of the medium. While air entry pressure is a crucial value of the water retention curve, defining the relation between saturation and capillary pressure. From a series of sensitivity analyses, low compressibility resulted in faster flow due to low storage term, while low air entry pressure slowed flow inflow into the bentonite. Low air entry pressure means the air easily enters the medium; hence the flow rate becomes lower based on the relativity permeability definition. Based on the sensitivity analysis, we further investigate the effect of shotcrete around the tunnel and excavation damaged zone. Also, long-term analysis considering heat decay of the radioactive waste will be considered in future studies.

Backfill is one of the key elements of deep geological disposal. The backfill material is used to fill disposal tunnels and is mainly composed of swellable clay, preventing the migration of nuclide and structurally supporting the tunnel. The selection and application of backfill material are critical for the stable and efficient disposal of spent fuel. Therefore, it is essential to secure various candidate materials for backfill and to comprehensively understand the properties and behavior of these materials. Recently, the Korea Atomic Energy Research Institute has selected a candidate material called Bentonil-WRK and is evaluating its applicability. To utilize this material as backfill, the safety function of a mixed backfill concept, consisting of sand and Bentonil-WRK, was assessed. The swelling pressure was measured as a function of dry density for a bentonite/silica sand mix ratio of 3/7. The results showed that the swelling pressure ranged from 0.15 to 0.273 MPa, depending on the dry density, with higher dry densities resulting in higher swelling pressures. The measured swelling pressure met the target performance criteria suggested by SKB and Posiva (i. e., 0.1 MPa), but did not meet the design requirement for swelling pressure (i. e., 1 MPa). This indicate the need for further research after increasing the mass fraction of bentonite (e. g., mix ratio 4/6 or more). The results of this study are expected to be used in the selection of candidate backfill materials and the establishment of design guidelines for engineered barrier backfill.

A methodology is under development to reconstruct and predict the long-term evolution of the natural barrier comprising the site of radioactive waste disposal. The natural barrier must protect the human zone from radionuclides for a long time. So for this, we need to be able to restore the evolution of the bedrock constituting the natural barrier from the past to the present and to predict from the present to the future. A methodology is being studied using surface outcrop, tunnel face of KURT (KAERI Underground Research Tunnel), and drill core at KAERI (Korea Atomic Energy Research Institute). Among them, drill core is an essential material for identifying deep geological properties, which could not be confirmed near the surface when considering the geological condition of the repository in the deep part. In this study, we selected several qualitative and quantitative analyses to construct a deep lithological model from the disposal perspective. These were applied to drill core samples around the KURT. There are the dikes presumed the Cretaceous were intruded by Jurassic granitoids in the study area. Analyzing trace elements of each rock type in the study area classified through geochemical characteristics and microstructure in previous studies made it possible to obtain qualitative information on the petrogenetic process. In addition, synthesizing the quantitative numerical age allows for grasping the evolution of bedrock, including intrusion and cutting relationships. LAICPMS was used for determining the age of zircons in plutonic rocks. The highly reliable 40Ar-39Ar method was selected for volcanic rocks because it can correct the loss of Ar gas and obtain the values of two types of Ar isotopes in a single sample. As a result, it was possible to infer the formation environment of rocks through anomalies in specific trace element content. And according to the numerical ages, it was possible to support the known separated rock type found in previous studies or to present a quantitative precedence relation for unclassified rocks. These methods could be applied to reconstruct the long-term evolution of bedrock within natural barriers.

In the engineered barrier system of deep geological disposal repository, complex physicochemical phenomena occur throughout the entire disposal time, consequently impacting the safety function. The bentonite buffer, a significant component of the engineered barrier system, can be geochemically altered due to the changes in host rock groundwater, temperature, and redox condition. Such changes may have direct or indirect effects on radionuclide migration in case of canister failure. Therefore, a modeling tool that accounts for coupled thermal-hydraulic-mechanical-chemical (THMC) processes is necessary for the safety assessment. To this end, the Korea Atomic Energy Research Institute (KAERI) has developed the APro, a modeling interface for conducting safety assessment of deep geological disposal repository. The APro considers coupled THMC processes that influence radionuclide migration. Here, the solute transport considering thermal and hydraulic processes are calculated using the COMSOL multi-physics, while geochemical reactions are carried out in PHREEQC. The two software are coupled using a sequential non-iterative operator splitting approach, and transport of non-water H, non-water O, and charge were additionally considered to enhance the coupling model stability. Finally, the applicability of APro to simulate long-term geochemical evolution of bentonite was demonstrated through benchmark studies to evaluate the effects of mineral precipitation/dissolution, temperature, redox, and seawater intrusion.

The purpose of this study was to examine whether galvanic corrosion of copper occurs by inserting a third barrier layer with a higher corrosion potential than copper between copper and cast iron when the copper layer is locally perforated by pitting or partial corrosion. A triple layer composed of copper, inserted metal, and carbon steel was manufactured by cold spray coating of inserting metal powders such as Ag, Ni, and Ti on carbon steel plate followed by Cu coating on it. First, the corrosion properties were evaluated electrochemically for each metal coating. As a result of Tafel plot anaylsis in KURT groundwater condition, the corrosion potential of Fe (-567 mV) was much lower than that of Cu (-91 mV), and the corrosion potential of Ni (-150 mV) was also lower than that of Cu. Therefore, Ni was likely to corrode before Cu. However, the corrosion current of Ni was lower than that of the Cu. In the galvanic specimen where the copper and inserting metal were exposed together, Cu-Fe was much lower corrosion potential of -446 mV, and the corrosion potential of Cu-Ti, Cu-Ni, and Cu-Ag were slightly higher than that of Cu. Therefore, it seemed that Ag, Ni, and Ti all might promote galvanic corrosion of surrounding copper when the copper layer was perforated to the inserted metal layer. If the metal insertion presented in this study operates properly, the disposal container does not need to worry about the partial corrosion or non-uniform corrosion of external copper layer.

IAEA safety standards document and international programs (such as BIOMASS) related to the assessment of the biosphere around High Level Radioactive Waste (including Spent Nuclear Fuel) repositories require the assessment of the biosphere to use the assumption that the current natural environment and human society will be maintained, and at the same time, the evolution of the distant future changes also need to be taken into account. In Korea, which has not designated candidate disposal sites, it is necessary to investigate and predict the current state and future changes of the natural environment throughout Korea and apply it practically to Biosphere assessment (for BDCF derivation) for candidate disposal sites suitability assessment and Safety Case (for performance assessment) preparation for design, construction, operation, and post-closure management. To this end, the natural environment in the fields of Topography, Geology, Soil, Ecology, Weather and Climate, Animals and Plants, Hydrology, Ocean, Land-use, etc. and human society in the fields of Population Distribution, Spatial-Planning, Urban Form, Industrial-Structure, Lifestyle etc. are being investigated in the context of current status, past change records, and future change potential in the Korean Peninsula. This paper summarizes those investigations to date. This study referred Biomass-6 [IAEA] and National Atlas I (2019)/II (2020)/III (2021) [National Geographic Information Institute of the Korea Ministry of Land, Infrastructure and Transport].

To obtain a license for a deep geological disposal repository for spent nuclear fuel, it is necessary to perform a safety assessment that quantifies the radiological impact on the environment and humans. One of the key steps in the safety assessment of a deep geological repository is the development of scenarios that describe how the repository evolves over the performance period and how events and processes affect performance. In the field of scenario development, demonstrating comprehensiveness is critical, which describes whether all factors that are expected to have a significant impact on the repository's performance have been considered. Mathematical proof of this is impossible. However, If the scenario development process is logical and systematic, it can support the claim that the scenario is comprehensive. Three primary approaches are being considered for scenario development: ‘Bottomup’, ‘Top-down’, and ‘Hybrid’. Hybrid approach provides a more systematic and structured process by considering both the FEPs (Features, Events, Processes) and safety functions utilized in the bottomup and top-down approaches. Many countries that develop recent scenarios prefer demonstrating scenario comprehensiveness using a hybrid approach. In this study, a systematic and structured scenario development process of a hybrid approach was formulated. Based on this, sub-scenarios were extracted that describe the phenomena occurring in the repository over the performance period, categorized by period. By integrating and screening the extracted sub-scenarios, a scenario describing the phenomena occurring over the entire period of disposal was developed.

In Korea, borated stainless steel (BSS) is used as a storage rack in spent fuel pools (SFP) to maintain the nuclear criticality of spent fuels. As the number of nuclear power plants and the corresponding amount of spent fuels increased, the density in SFP storage rack also increased. In this regard, maintaining subcriticality of spent nuclear fuels became an issue and BSS was selected as the structural material and neutron absorber for high density storage rack. Since it is difficult to replace the storage rack, corrosion resistance and neutron absorbency are required for long period. BSS is based on stainless steel 304 and is specified in the ASTM A887-89 standard depending on the boron concentration from 304B (0.20-0.29% B) to 304B7 (1.75-2.25% B). Due to the low solubility of boron in austenitic stainless steel, metallic borides such as (Fe, Cr) 2B are formed as a secondary phase. Metallic borides could cause Cr depletion near it, which could decrease the corrosion resistance of the material. In this paper, the long-term corrosion behavior of BSS and its oxide microstructures are investigated through accelerated corrosion experiment in simulated SFP conditions. Because the corrosion rate of austenitic stainless steel is known to be dependent on the Arrhenius equation, a function of temperature, the corrosion experiment is conducted by increasing the experimental temperature. Detail microstructural analysis is conducted using a scanning electron microscope, transmission electron microscope and energy dispersive spectrometer. After oxidation, a hematite structure oxide film is formed, and pitting corrosion occurs on the surface of specimens. Most of the pitting corrosion is found at the substrate surface because the corrosion resistance of the substrate, which has low Cr content, is relatively low. Also, the oxidation reaction of B in the secondary phase has the lowest Gibbs free energy compared to other elements. Furthermore, oxidation of Cr has low Gibbs free energy, which means that oxidation of B and Cr could be faster than other elements. Thus, the long-term corrosion might affect the boron content and the neutron absorption ability of the material. Using boron’s high cross-section for neutrons, the neutron absorption performance of BSS was evaluated through neutron transmission tests. The effect of the corrosion behavior of BSS on its neutron absorption performance was investigated. Samples simulated to undergo up to 60 years of degradation before corrosion through accelerated corrosion testing did not show significant changes in the neutron shielding ability before and after corrosion. This can be explained in relation to the corrosion behavior of BSS. Boron was only leached out from the secondary phase exposed on the surface, and this oxidized secondary phase corresponds to about 0.17% of the volume of the total secondary phase. This can be seen as a very small proportion compared to the total boron content and is not expected to have a significant impact on neutron absorption performance.

South Korea has been storing UNF in spent fuel pool dry storage facility within Nuclear Power Plants. The dry storage facility of used nuclear fuel (UNF) is essential to sustain safety and sustain stable operation of a nuclear power plant. Most abroad countries have attempted to develop a variety of dry storage facility for used nuclear fuel in order to retain the safe restoration. Many studies have been conducting to safety evaluation for the dry storage facility. However, there is not a ventilation evaluation in the wake of fire event that could influence of the thermal effect on the dry storage facility, even though it will likely to occur fire events such as wildfire, air craft crash. In practice, it happened to catastrophic disaster due to the wild fire adjacent to ul-jin mountain. Also, it happened to fire accident near to the Japonia NPP in Ukraine territory caused of military air plane missile. It has not mostly been studied on the ventilation evaluation considered to thermal safety in the dry storage facility excepted for some researches. It could need the mechanical ventilation systems such as HVAC system in the dry storage system, so that thermal effect can be reduced. In this study, we conducted to the ventilation control modelling by using fire modelling tool (Fire Dynamic Simulator v.6.7). The ventilation scenarios made up for 3 case that can compare flowrate variation with ventilation control. As a result of modelling, there is no differentiation between ventilation control using performance curve with not using performance curve even though the pressure fluctuation would be increased, compared with the case of considering performance curve. Second, it evaluated that the mode for fraction control would occur to pressure rise in the state of controlling the ventilation system flowrate. However, sensitivity of flowrate control was more decreased below less than 5 seconds. Third, in the case of on/off control system revealed more higher resolution than other cases caused by flowrate variation. These results could be considered as the design guidelines for the development dry storage facility to improve the thermal performance that can reduce thermal risk. Furthermore, the study results would expect HVAC system installed in dry storage to help automatic ventilation control relevant to dry storage safety increased.

Korea Atomic Energy Research Institute (KAERI) has been operating the Post Irradiation Examination Facility (PIEF) for spent fuel. The facility has pools and hot cells for handling and examining fuel assemblies and rods. In the first hot cell, non-destructive tests such as visual inspection, defect detection, oxide layer thickness measurement, and gamma scanning are performed on a full-length fuel rod. Then, the fuel rod is transported to the next hot cell for measuring the rod internal pressure (RIP). After the RIP measurement, the fuel rod is cut by a cutting machine to make samples for destructive tests. Currently, the existing cutting machine is broken, so a new machine needed to be designed and manufactured. The major considerations for designing the cutting machine were convenience of remote handling and decontamination. The machine was modularized and its handling parts were designed to be easily controlled by manipulators. The cover was designed to prevent radioactive contamination of the surrounding area.

Korean MMTT project has been launched in order to clarify the vibration and shock loads under normal condition and transportation (NCT) in Korean geological and transportation conditions and to evaluate the integrity of SNF under such a transportation load. To evaluate the integrity of the SNF during normal land and sea transport tests, a representative SNF that represents the entirety of the different types of SNFs stored in the spent fuel pool of the power plant should be selected. And, it is necessary to make the test assembly to have a statically and dynamically similar behavior with the actual SNF. Therefore, in this project, we selected two types of fuel assembly that are expected to exhibit relatively conservative behavior under NCT, and these assemblies are being fabricated into surrogate test assemblies to have a similar characteristic as actual SNF based on the accumulated data from the poolside examination and the hot cell test so far. Tests were conducted for NCT conditions. In addition, a fatigue test was performed to integrity of the nuclear fuel rods under NCT conditions. Nuclear fuel assemblies are transported while being laid inside the cask under NCT, and are exposed to external shocks and vibrations. At this time, the fuel rod between the grid and grid is exposed to bending motion by this external force. For this simulation, a fixture was developed and used for static bending tests and bending fatigue tests. To simulate spent nuclear fuel rod specimens, hydrogen reorientation Zry-4 cladding was used and simulated pellets made of stainless steel were applied. And also, it was bonded using epoxy to give bonding conditions between the inside and the pellet. As a result of the test, cracks occurred due to the concentrated load between the pellets, resulting in damage to the fuel rod. The fatigue results showed a similar trend compared to the results performed by ORNL, and the lower bound fatigue curve presented by NUREG-2224 was also satisfactory.