Zirconium(Zr) alloys are commonly used in the nuclear industry for applications such as fuel cladding and pressure tubes. To minimize the levels and volumes of radioactive waste, molten salts have been employed for decontaminating Zr alloys. Recently, a two-step Zr metal recovery process, combining electrolysis and thermal decomposition, has been proposed. In the electrolysis process, potentiostatic electrorefining is utilized to control the chemical form of electrodeposits(ZrCl). Although Zr metals are expected to dissolve into molten salts, reductive alloy elements can also be co-dissolved and deposited on the cathode. Therefore, a better understanding of the anodic side’s response during potentiostatic electrorefining is necessary to ensure the purity of recovered Zr and long-term process operation. As the first step, potentiodynamic polarization curves were obtained using Zr, Nb, and Zr-Nb alloy to investigate the anodic dissolution behavior in the molten salts. Nb, which has a redox potential close to Zr, and Zr exhibit active or passivation dissolution mechanisms depending on the potential range. It was confirmed that Zr-Nb alloy also has a passivation region between -0.223 to -0.092 V influenced by the major elements Zr and Nb. Secondly, active dissolution of Zr-Nb was performed in the range of -0.9 to -0.6 V. The dissolution mechanism can be explained by percolation theory, which is consistent with the observed microstructure of the alloy. Thirdly, passivation dissolution of Zr, Nb, and Zr-Nb alloy was investigated to identify the pure passivation products and additional products in the Zr-Nb alloy case. K2ZrCl6 and K3NbCl6 were identified as the pure passivation products of the major elements. In the Zr-Nb alloy case, additional products, such as Nb and NbZr, produced by the redox reaction of nanoparticles in the high viscous salt layer near the anode, were also confirmed. The anodic dissolution mechanism of Zr-Nb alloy can be summarized as follows. During active dissolution, only Zr metal dissolves into molten salts by percolation. Above the solubility near the anode, passivation products begin to form. The anode potential increases due to the disturbance of passivation products on ion flow, leading to co-dissolution of Nb. When the concentration of Nb ion exceeds the solubility, a passivation product of Nb also forms. In this scenario, a high viscous salt layer is formed, which traps nanoparticles of Zr metal, resulting in redox behavior between Zr metal and Nb ion. Some nanoparticles of Zr and Nb metal are also present in the form of NbZr.

A low- and intermediate-level radioactive waste repository contains different types of radionuclides and organic complexing agents. Their chemical interaction in the repository can result in the formation of radionuclide-ligand complexes, leading to their high transport behaviors in the engineered and natural rock barriers. Furthermore, the release of radionuclides from the repository can pose a significant risk to both human health and the environment. This study explores the impact of different experimental conditions on the transport behaviors of 99Tc, 137Cs, and 238U through three types of barrier samples: concrete, sedimentary rock, and granite. To assess the transport behavior of the samples, the geochemical characteristics were determined using X-ray diffraction (XRD), X-ray fluorescence (XRF), Fouriertransform infrared spectroscopy (FTIR), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDS), and Brunauer-Emmett-Teller (BET) analysis. The adsorption distribution coefficient (Kd) was used as an indicator of transport behavior, and it was determined in batch systems under different conditions such as solution pH (ranging from 7 to 13), temperature (ranging from 10 to 40°C), and with the presence of organic complexing agents such as ethylenediaminetetraacetic acid (EDTA), nitrilotriacetic acid (NTA), and isosaccharinic acid (ISA). A support vector machine (SVM) was used to develop a prediction model for the Kd values. It was found that, regardless of the experimental parameters, 99Tc may migrate easily due to its anionic property. Conversely, 137Cs showed low transport behaviors under all tested conditions. The transport behaviors of 238U were impacted by the order of EDTA > NTA> ISA, particularly with the concrete sample. The SVM models can also be used to predict the Kd values of the radionuclides in the event of an accidental release from the repository.

The organic complexing agents such as ethylenediaminetetraacetic acid (EDTA), nitrilotriacetic acid (NTA), and isosaccharinic acid (ISA) can enhance the radionuclides’ solubility and have the potential to induce the acceleration of radionuclides’ mobility to a far-field from the radioactive waste repository. Hence, it is essential to evaluate the effect of organic complexing agents on radionuclide solubility through experimental analysis under similar conditions to those at the radioactive waste disposal site. In this study, five radionuclides (cesium, cobalt, strontium, iodine, and uranium) and three organic complexing agents (EDTA, NTA, and ISA) were selected as model substances. To simulate environmental conditions, the groundwater was collected near the repository and applied for solubility experiments. The solubility experiments were carried out under various ranges of pHs (7, 9, 11, and 13), temperatures (10°C, 20°C, and 40°C), and concentrations of organic complexing agents (0, 10-5, 10-4, 10-3, and 10-2 M). Experimental results showed that the presence of organic complexing agents significantly increased the solubility of the radionuclides. Cobalt and strontium had high solubility enhancement factors, even at low concentrations of organic complexing agents. We also developed a support vector machine (SVM) model using some of the experimental data and validated it using the rest of the solubility data. The root mean square error (RMSE) in the training and validation sets was 0.012 and 0.016, respectively. The SVM model allowed us to estimate the solubility value under untested conditions (e.g., pH 12, temperature 30°C, ISA 5×10-4 M). Therefore, our experimental solubility data and the SVM model can be used to predict radionuclide solubility and solubility enhancement by organic complexing agents under various conditions.

In response to a regulatory mandate, all nuclear licensees are obligated to establish an information system that can provide essential information in the event of a radiation emergency by connecting the monitoring data of the Safety Parameter Display System (SPDS) or equivalent system to the Korea Institute of Nuclear Safety (KINS). Responding to this responsibility, the Korea Atomic Energy Research Institute (KAERI) has established the Safety Information Transmission System (SITS), which enables the collection and real-time monitoring of safety information. The KAERI monitors and collects safety information, which includes data from the HANARO Operation Work Station (OWS) and the HANARO & HANARO Fuel Fabrication Plant (HFFP) Radioactivity Monitoring System (RMS), and the Environmental Radiation Monitoring System (ERMS) & meteorological data. Currently, the transmission of this safety information to the AtomCARE server of the KINS takes place via the SITS server located in the Emergency Operations Facility (EOF). However, the multi-path of transmission through SITS has caused problems such as an increase in data transmission interruptions and errors, as well as delays in identifying the cause and implementing system recovery measures. To address these issues, a new VPN is currently being constructed on the servers of nuclear facilities that generate and manage safety information to establish a direct transmission system of safety information from each nuclear facility to the AtomCARE server. The establishment of a direct transmission system that eliminates unnecessary transit steps is expected to result in stable information transmission and minimize the frequency of data transmission interruptions. As of the improvement progress, a security review was conducted in the second and third quarters of 2022 to evaluate the security of newly introduced VPNs to the nuclear facility server, and based on the results of the review, security measures were strengthened. In the fourth quarter of 2022, the development of a direct transmission system for safety information began, and it is scheduled to be completed by the fourth quarter of 2023. The project includes the construction of the transmission system, system inspection, and comprehensive data stability testing. Afterward, the existing SITS located in the EOF will be renamed as the Safety Information Display System (SIDS), and there are plans to remove any unused servers and VPNs.

Aluminum’s exceptional properties, such as its high strength-to-weight ratio, excellent thermal conductivity, corrosion resistance, and low neutron absorption cross-section, make it an ideal material for diverse nuclear industry applications, including aluminum plating for the building envelope of nuclear power plants. However, plating aluminum presents challenges due to its high reactivity with oxygen and moisture, thus, complicating the process in the absence of controlled environments. Plating under an inert atmosphere is often used as an alternative. However, maintaining an inert atmosphere can be expensive and presents an economic challenge. To address these challenges, an innovative approach is introduced by using deep eutectic solvents (DES) as a substitute for traditional aqueous electrolytes due to the high solubility of metal salts, and wide electrochemical window. In addition, DESs offer the benefits of low toxicity, low flammability, and environmentally friendly, which makes DESs candidates for industrial-scale applications. In this study, we employed an AlCl3-Urea DES as the electrolyte and investigated its potential for producing aluminum coatings on copper substrates under controlled conditions, for example, current density, deposition duration, and temperature. A decane protective layer, non-polar molecular, has been used to shield the AlCl3-Urea electrolyte from the air during the electrodeposition process. The electrodeposition was successful after being left in the air for two weeks. This study presents a promising and innovative approach to optimizing aluminum electrodeposition using deep eutectic solvents, with potential applications in various areas of the nuclear industry, including fuel cladding, waste encapsulation, and radiation shielding.

The soils contaminated with radionuclides such as Cs-137 and Sr-90 should be solidified using a binder matrix, because radioactively contaminated soils pose environmental concerns and human health problems. Ordinary Portland cement has been widely used to solidify various radioactive wastes due to its low cost and simple process. In this study, simulant soil waste was solidified using cement waste form. The soils were collected around ‘Kori Nuclear Power Plant Unit 1’ and they were contaminated with the prepared simulant liquid waste containing Fe, Cr, Cs, Ni, Co, and Mn. The water-to-dry ingredients (W/D) ratio of cement waste form was 0.40. The cement paste was poured into a cubic mold (5×5×5 cm) and then cured for 28 days at room temperature. The 28-day compressive strength, water immersion, and EPA1311-toxicity characteristic leaching procedure (TCLP) tests were performed to evaluate the structural stability of cement waste form. The compressive strength was not proportional to soil waste loading, and the lowest compressive strength (4±0.1 MPa) was achieved in cement waste form containing 50wt% soil waste. After the water immersion test for 90 days, the compressive strength of cement waste form with 50wt% soil waste increased to 7.5±0.6 MPa, meeting the waste form acceptance criteria in the repository. It is believed that long-term water immersion test contributed to the additional curing and hydration reaction, resulting in the enhanced compressive strength. As a result of the TCLP test, the released amount of As, Ba, Cd, Cr, Pb, Se, Co, Cs, and Sr was less than the domestic and international standards. These results imply that cement waste form can be a promising candidate for the solidification of radioactive soil wastes.

Laser cutting has been recognized as one of key techniques in dismantling nuclear power plants as it has several advantages such as a remote operation and a reduced secondary waste. However, it generates a significant amount of aerosols that can pose a health risk to workers and further induce environmental pollution during the cutting operation. Thus, understanding the aerosol characteristics generated by the laser cutting is crucial for implementing an effective cutting operation and reducing the exposure to these hazardous particles. In this work, we established a methodology to collect the aerosols and investigate their properties in the laser cutting operation. We built an integrated laser cutting system for aerosol analyses, consisting of a high-power laser cutting module, a metal sample holder, an aerosol collector, and a closed chamber. We expect that this system will offer an opportunity for in-depth understanding of the aerosol properties, by connecting it with desired type of aerosol analysis platforms, and further safe dismantling operation of the nuclear power plants.

Laser cutting has many advantages, including high-speed cutting potential, no reaction forces, narrow kerf widths, ease of remote control, and more. This makes it the next generation cutting technology for nuclear decommissioning. For this reason, various groups in countries with nuclear power plants have been working on applying laser cutting to nuclear decommissioning. Our group has also been developing in-air and underwater laser cutting technologies. Previous research has focused on efficiently cutting thicker steels. To accomplish this, a cutting head with a long focusing element with a focal length of 600 mm was utilized. A long focusing head is advantageous for cutting thick objects at high speeds because it can maintain a high power density over a long distance. However, with such a long focused beam, the residual laser power that remains after passing through the target object can cut or damage other unwanted objects located behind the target. Utilizing a short focused element can solve this problem, but if the focal length is too short, the cutting capability will be reduced. In this work, we developed and applied a cutting head that utilizes a focused element with a short focal length of 300 mm. Cutting tests with this head allowed us to cut 10-60 mm thick stainless steel plates at a laser power of 6 kW. We also obtained the maximum cutting speed and kerf width for each thickness while increasing the laser power by 1 kW from 1 to 6 kW. The results obtained in this work are expected to be utilized for safe cutting in future nuclear decommissioning applications.

RUCAS (Recycling-Underlying Computational Dose Assessment System), a dose assessment program based on the RESRAD-RECYCLE framework, is designed to evaluate dose for recycling scenarios of radioactive waste in metals and concrete. To confirm the validity of the recycling scenarios provided by RUCAS, comparative evaluations will be conducted with RESRAD-RECYCLE for metal radioactive waste recycling scenarios and with MicroShield® for concrete radioactive waste recycling scenarios. In the evaluation of metal recycling scenarios without shielding, RUCAS showed similar results when compared to both MicroShield® and RESRAD-RECYCLE. This validates the function of dose assessments using RUCAS for metal recycling scenarios. However, when shielding was present, RUCAS produced results that were comparable to MicroShield®, but differed from those of RESRAD-RECYCLE. The underestimation of dose values up to 1.66E+08 times difference by RESRAD-RECYCLE could potentially decrease reliability and safety in evaluated doses, further emphasizing the importance of RUCAS. Because validation is also necessary for the expanded calculation capabilities resulting from methodological changes of RUCAS (i.e., various radiation source geometries), based on prior validations, it was determined that additional validations are required for different radiation source materials and shielding conditions. In case where the radiation source and shielding materials were identical, RUCAS and MicroShield® produced similar results according to both the Kalos et al. (1974) and Lin and Jiang (1996) methodologies. This demonstrates that the that differences in methodology are inconsequential when considering the same source and shielding materials. However, when the atomic number of the radiation source materials was larger than that of shielding material (HZ-LZ condition), RUCAS obtained results similar to MicroShield® only for the Kalos et al. (1974) methodology. While Lin and Jiang (1996) methodology yield higher results than MicroShield®. Lastly, in case where the atomic number of the radiation source material was smaller than that of the shielding material (LZ-HZ condition,) both methodologies yielded results comparable to MicroShield®. In conclusion, the validity of RUCAS’s shielding calculations has been verified, confirming improvements in dose assessment compared to RESRAD-RECYCLE. Additionally, we observed that shielding effectiveness calculations differ depending on the methodology of build-up effect. If the validity of these methodologies is confirmed, it is expected that selecting the most advantageous methodology for each condition will enable more rational dose assessments. Consequently, in future research, we plan to evaluate the validity of Lin and Jiang (1996) methodology using particle transport codes based on the Monte Carlo method, such as MCNP and Geant 4, rather than MicroShield®.

The homogeneity of radioactive spent ion exchange resins (IERs) distribution inside waste form is one of the important characteristics for acceptance of waste forms in long-term storage because heterogenous immobilization can lead to the poor structural stability of waste form. In this study, the homogeneity of metakaolin-based geopolymer waste form containing simulant IERs was evaluated using a laser-induced breakdown spectroscopy (LIBS) and statistical approach. The cation-anion mixed IERs (IRN150) were used to prepare the simulant spent IERs contaminated by non-radioactive Cs, Fe, Cr, Mn, Ni, Co, and Sr (0.44, 8.03, 6.22, 4.21, 4.66, 0.48, and 0.90 mg/g-dried IER, respectively). The K2SiO3 solution to metakaolin ratio was kept constant at 1.2 and spent IERs loading was 5wt%. For the synthesis of homogeneous geopolymer waste form, spent IERs were mixed with K2SiO3 solution and metakaolin first, and then the fresh mixture slurry was poured into plastic molds (diameter: 2.9 cm and height: 6.0 cm). The heterogeneous geopolymer waste form was also fabricated by stacking two kinds of mixtures (8wt% IERs loading in bottom and 2wt% in top) in one mold. Geopolymers were cured for 7d (1d at room temperature and 6d at 60°C). The hardened geopolymers were cut into top, middle, and bottom parts. The LIBS spectra and intensities for Cs were obtained from the top and bottom of each part. Cs was selected for target nuclide because of its good sensitivity for measurement. Shapiro-Wilk test was performed to determine the normality of LIBS data, and it revealed that data from the homogeneous sample is normal distribution (p-value = 0.9246, if p-value is higher than 0.05, it is considered as normal distribution). However, data from the heterogeneous sample showed abnormal distribution (p-value = 7.765×10-8). The coefficient of variation (CoV) was also calculated to examine the dispersion of data. It was 31.3% and 51.8% from homogeneous and heterogeneous samples, respectively. These results suggest that LIBS analysis and statistical approaches can be used to evaluate the homogeneity of waste forms for the acceptance criterion in repositories.

Level measurement of liquid radwaste is essential for inventory management of treatment system. Among various methods, level measurement based on differential pressure has many advantages. First, it is possible to measure the liquid level of the system regardless of liquid type. Second, as the instrument doesn’t need to be installed near the tank, there is no need to contact the tank when managing it. Therefore, workers’ radiation dose from the system can be decreased. Finally, although it depends on the accuracy, the price of the instrument is relatively low. With these advantages, in general, liquid radwaste level in a tank is measured using differential pressure in the treatment system. Not only the advantages described above, there are some disadvantages. As the liquid in the system is waste, it is not pure but has some suspended materials. These materials can be accumulated in tanks and pipes where the liquids move to come into direct contact with pneumatic pipes that are essential in differential pressure instruments. As a result, in case of a treatment using heat source, the accumulated materials may become sludge causing interference in pneumatic pipes. And this can change the pressure which also affects the level measured. In conclusion, in case of liquid storage tanks in which the situation cannot be checked, the proficiency of an operator becomes important.

The engineered barrier system (EBS) for deep geological disposal of high-level radioactive waste requires a buffer material that can prevent groundwater infiltration, protect the canister, dissipate decay heat effectively, and delay the transport of radioactive materials. To meet those stringent performance criteria, the buffer material is prepared as a compacted block with high-density using various press methods. However, crack and degradation induced by stress relaxation and moisture changes in the compacted bentonite blocks, which are manufactured according to the geometry of the disposal hole, can critically affect the performance of the buffer. Therefore, it is imperative to develop an adequate method for quality assessment of the compacted buffer block. Recently, several non-destructive testing methods, including elastic wave measurement technology, have been attempted to evaluate the quality and aging of various construction materials. In this study, we have evaluated the compressive wave velocity of compacted bentonite blocks via the ultrasonic velocity method (UVM) and free-free resonant column method (FFRC), and analyzed the relationship among compressive wave velocity, dry density, thermal conductivity, and strength parameter. We prepared compacted bentonite block specimens using the cold isostatic pressure (CIP) method under different water content and CIP pressure conditions. Based on multiple regression analysis, we suggest a prediction model for dry density in terms of manufacturing conditions. Additionally, we propose an empirical model to predict thermal conductivity and unconfined compressive strength based on compressive wave velocity. The database and suggested models in this study can contribute to the development of quality assessment and prediction techniques for compacted buffer blocks used in the construction of a disposal repository.

High level radioactive waste disposal repository is faced thermos-hydro-mechanical-radioactive condition. Factors according to these complex conditions are measured using multiple sensors installed in the disposal repository to check integrity of the structure. Wires of the sensors can be potential pathways of groundwater and nuclide flow and these pathways accelerates bentonite saturation. Therefore, it is worth to developing wireless sensors buried in the bentonite buffer which can communicate without wires. In start of the study, widely-utilized wireless communication methods including WiFi and LoRa are tested using compacted bentonite blocks to estimate the performance of them. Compacted bentonite blocks are prepaired using di-press method with metal molds and the dry density of them are about 1.6 g/cm3. All wireless communication methods are well communicated through the bentonite blocks over 50 cm. The further experimental tests will be conducted with different dry density and water contents. The results of these experimental tests give a possibility of wireless communications in compacted bentonite buffer and will be utilized for the design of wireless sensor systems for the repository monitoring.

For the performance analysis of deep geological repository systems, numerical simulation with multi-physics is required, which specifically covers Thermal (T), Hydraulic (H), and Mechanical (M) behaviors in the disposal environment. Numerous simulation models have been developed so far, each of which varies in the approach and methodology for solving THM problems. Fully-coupled THM simulation codes such as ROCMAS, THAMES, and CODE_BRIGHT were mainly developed in the initial stage of DEvelopment of COupled models and their VALidation against EXperiments (DECOVALEX), with the advantage of thorough calculations consisting of correlated several variables on different physics. Due to the difficulty of solving the complex Jacobian Matrix and the following burden for the computational calculation, weakly-coupled THM models have been suggested in recent researches: TOUGH2-MP with FLAC3D, TOUGH2 with UDEC and OpenGeoSys with FLAC3D. This methodology of loose coupling allows the practical use of computational code optimized for each physics, thereby increasing the efficiency in simulation. However, these suggested models require two different numerical codes to calculate THM behaviors, which leads to several inherent issues: compatibility during maintenance, updating and dependency between two codes. In this study, therefore, the authors build a unified code for simulating THM behaviors in the deep geological repository. The concept involves the iterative sequential coupling between TH and M for calculation efficiency. As having developed the simulation code, High-level rAdiowaste Disposal Evaluation System (HADES), to describe TH behavior based on Multi-physics Object-Oriented Simulation Environment (MOOSE) software, the authors make a milestone to develop and couple the MOOSE-based new code for M behavior as Sub-app, with the previous HADES set to be Main-app. New model for M behavior will be verified with the benchmark case of DECOVALEX-THMC Task D, comparing the mechanical simulation results: stress evolution over time, profiles of stress and vertical displacement. The existing simulation results from HADES will also be updated with the coupled calculations, with regard to temperature and saturation. Additionally, the effective stress evolution can be assessed in terms of repository’s stability with Spalling Strength and Mohr-Coulomb failure criterion. This concept for new simulation model has its meaning in that it aims to demonstrate the specific methodology of loosely coupling multi-physics in unified simulation code and analyze THM complex interactions with considering mutual influence on various physics. It is expected that HADES can be renewed as an integral simulation model for deep geological repository systems by possessing the capacity for analyzing and assessing mechanical behavior.

Backfill is one of the key elements of deep geological disposal. The backfill material is used to fill disposal tunnels and is mainly composed of swellable clay, preventing the migration of nuclide and structurally supporting the tunnel. The selection and application of backfill material are critical for the stable and efficient disposal of spent fuel. Therefore, it is essential to secure various candidate materials for backfill and to comprehensively understand the properties and behavior of these materials. Recently, the Korea Atomic Energy Research Institute has selected a candidate material called Bentonil-WRK and is evaluating its applicability. To utilize this material as backfill, the safety function of a mixed backfill concept, consisting of sand and Bentonil-WRK, was assessed. The swelling pressure was measured as a function of dry density for a bentonite/silica sand mix ratio of 3/7. The results showed that the swelling pressure ranged from 0.15 to 0.273 MPa, depending on the dry density, with higher dry densities resulting in higher swelling pressures. The measured swelling pressure met the target performance criteria suggested by SKB and Posiva (i. e., 0.1 MPa), but did not meet the design requirement for swelling pressure (i. e., 1 MPa). This indicate the need for further research after increasing the mass fraction of bentonite (e. g., mix ratio 4/6 or more). The results of this study are expected to be used in the selection of candidate backfill materials and the establishment of design guidelines for engineered barrier backfill.

A methodology is under development to reconstruct and predict the long-term evolution of the natural barrier comprising the site of radioactive waste disposal. The natural barrier must protect the human zone from radionuclides for a long time. So for this, we need to be able to restore the evolution of the bedrock constituting the natural barrier from the past to the present and to predict from the present to the future. A methodology is being studied using surface outcrop, tunnel face of KURT (KAERI Underground Research Tunnel), and drill core at KAERI (Korea Atomic Energy Research Institute). Among them, drill core is an essential material for identifying deep geological properties, which could not be confirmed near the surface when considering the geological condition of the repository in the deep part. In this study, we selected several qualitative and quantitative analyses to construct a deep lithological model from the disposal perspective. These were applied to drill core samples around the KURT. There are the dikes presumed the Cretaceous were intruded by Jurassic granitoids in the study area. Analyzing trace elements of each rock type in the study area classified through geochemical characteristics and microstructure in previous studies made it possible to obtain qualitative information on the petrogenetic process. In addition, synthesizing the quantitative numerical age allows for grasping the evolution of bedrock, including intrusion and cutting relationships. LAICPMS was used for determining the age of zircons in plutonic rocks. The highly reliable 40Ar-39Ar method was selected for volcanic rocks because it can correct the loss of Ar gas and obtain the values of two types of Ar isotopes in a single sample. As a result, it was possible to infer the formation environment of rocks through anomalies in specific trace element content. And according to the numerical ages, it was possible to support the known separated rock type found in previous studies or to present a quantitative precedence relation for unclassified rocks. These methods could be applied to reconstruct the long-term evolution of bedrock within natural barriers.

The acoustic emission (AE) method as a passive non-destructive monitoring technique is proposed for real-time monitoring of mechanical degradation in underground structures, such as deep geological disposal of high-level nuclear waste (HLW). This study investigates the low-frequency characteristics of AE signals emitted during the fracturing of meter-scale concrete specimens; uniaxial compression tests (UCT) in a lab scale and Goodman jack (GJ) tests in a 1.3 m-long concrete block were conducted while acquiring the AE signals using low-frequency AE sensors. The results indicate a sharp increase in AE energy emission at approximately 60% and 80% of the yield stresses in the UCT and GJ tests, respectively. The collected AE signals were primarily found in two frequency bands: the 4-28 kHz range and the 56-80 kHz range. High-frequency AE signals were captured more as the stress increased in the GJ tests, which was in contrast to the UCT tests. Furthermore, the AE signals obtained from the Goodman jack tests tended to lower RA values than the UCT results. This study presents unique experimental data with low-frequency AE sensors under different loading conditions, which provides insights into field-scale AE monitoring practices.

The stabilization technology for the damaged spent fuel is being developed to process the damaged fuel into sound pellet suitable for dry re-fabrication. It requires several treatments including oxidative decladding followed by reduction treatment for oxidized powder closely related to the quality of oxidized powders for pellet fabrication. For the development of operating condition for the reduction treatment, in this study, we evaluated the effect of air-cylinder based vertical shaking previously applied to oxidative decladding on powder reduction. For U3O8 of 50-100 g, the reduction test were applied with and without vertical shaking at 700°C under reduction atmosphere (Ar + 4%H2) and the concentration of hydrogen in effluent was measured to evaluate the reduction reaction. It was found that the vertical shaking system has allowed the reaction time of 50 g and 100 g U3O8 reduced by 33% compared to the test in static mode. Based on XRD analysis, the better crystallinity of the products was also achieved.

According to the “Law on protection and response measures for nuclear facilities and radiation”, Nuclear Power Plant (NPP) licensees should conduct periodic exercises based on hypothetical cyberattack scenarios, and there is a need to select significant and probable ones in a systematic manner. Since cyber-attacks are carried out intentionally, it is difficult to statistically specify the sequences, and it is not easy to systematically establish exercise scenarios because existing engineering safety facilities can be forcibly disabled. To deal with the above situation, this paper suggests a procedure using the Probabilistic Safety Assessment (PSA) model to develop a cybersecurity exercise scenario. The process for creating cyber security exercise scenarios consists of (i) selecting cyber-attack-causing initiating events, (ii) identifying digital systems, (iii) assigning cyber-attack vectors to a digital system, (iv) determining and adding type for operator’s response, (v) modifying a baseline PSA model, and (vi) extracting top-ranked minimal cut sets, and (vii) selecting a representative scenario. This procedure is described in detail through a case study, an expected cyber-attack scenario General Transient-Anticipated Transient Without Scram (GTRN-ATWS). It refers to an accident scenario for ATWS induced by GTRN. Since ATWS is targeted for cyber training in some NPPs, and GTRN is one of the most common accidents occurring in NPPs, GTRN-ATWS was chosen as an example. As for the cyber-attack vector, portable media and mobile devices were selected as examples based on expert judgment. In this paper, only brief examples of GTRN-ATWS events have been presented, but future studies will be conducted on an analysis of all initiating events in which cyber-attacks can occur.

Background: The gluteus maximus (GM) muscle comprise the lumbo-pelvic complex and is an important stabilizing muscle during leg extension. In patients with low back pain (LBP) with weakness of the GM, spine leads to compensatory muscle activities such as instantaneous increase of the erector spinae (ES) muscle activity. Four-point kneeling arm and leg lift (FKALL) is most common types of lumbopelvic and GM muscles strengthening exercise. We assumed that altered hip position during FKALL may increase thoraco-lumbar stabilizer like GM activity more effectively method. Objects: The purpose of this study was investigated that effects of the three exercise postures on the right-sided GM, internal oblique (IO), external oblique (EO), and multifidus (MF) muscle activities and pelvic kinematic during FKALL. Methods: Twenty eight healthy individuals participated in this study. The exercises were performed three conditions of FKALL (pure FKALL, FKALL with 120° hip flexion of the supporting leg, FKALL with 30° hip abduction of the lifted leg). Participants performed FKALL exercises three times each condition, and motion sensor used to measure pelvic tilt and rotation angle. Results: This study demonstrated that no significant change in pelvic angle during hip movement in the FKALL (p > 0.05). However, the MF and GM muscle activities in FKALL with hip flexion and hip abduction is greater than pure FKALL position (p < 0.001). Conclusion: Our finding suggests that change the posture of the hip joint to facilitate GM muscle activation during trunk stabilization exercises such as the FKALL.