본 연구는 햄프씨드오일 (Cannabis sativa L. seed oil, CSO)와 햄프씨드오일 복합물 (Cannabis sativa L. seed oil complex, CSOC)의 비교분석을 통해 항염증 소재로서의 가능성을 평가하였다. CSO와 CSOC의 항염증 효과는 lipopolysaccharide (LPS)-induced RAW264.7 모델을 통해 확인하였다. Lipoxygenase inhibition activity를 통해 지질산화억제를 확인한 결과, CSO는 억제되지 않았지만 COSC는 70% 이상 억제되었다. MTT assay를 통해 세포독성을 확인해본 결과, CSO는 세포독성을 보이지 않았지 만 CSOC는 200 μg/ml 이상 농도에서 세포독성을 보였다. LPS로 유도된 RAW264.7에서 inducible nitric oxide synthase (iNOS)의 발현과 nitric oxide (NO)의 생산은 CSOC가 CSO보다 현저하게 억제하였다. 또한, cyclooxygenas (COX)-2의 발현과 prostraglandin E2 (PGE2)의 생성을 확인해본 결과에서도 CSOC 가 CSO보다 현저하게 억제하였다. 본 연구를 통해, CSOC가 CSO보다 우수한 항염증 효과를 가지며, 항 염증 소재로 활용 가능성이 있음을 확인했다.

호장근, 적하수오, 대황, 알로에 등과 같은 생약재의 주요 약리 활성 성분인 emodin은 항산 화, 항균, 항염, 항암, 간보호 등에 효능이 있는 것으로 보고되었다. 본 연구에서는 emodin의 피부 질 환 및 기능성 소재로서의 활용 가능성을 알아보기 위해 염증 개선과 피부장벽기능 개선 관련 활성을 확 인하였다. human keratinocyte인 HaCaT 세포에 대하여 항염효과를 관찰하기 위해 cytokine억제능은 ELISA kit로, 단백질 발현은 western blot으로 확인하였다. TNF-α (10 ng/mL)/IFN-γ (10 ng/mL)로 활성화된 HaCaT 세포에서 emodin을 농도별(5, 10, 20, 40) μM로 처리한 결과 TNF-α, IL-1β 및 IL-6의 생성량은 emodin의 농도가 증가함에 따라 감소됨을 확인하였다. 염증관련 단백질인 iNOS, COX-2 발현량에 대한 실험결과에서도 emodin 20 μM 농도에서 control 대비 iNOS는 48%, COX-2 는 29%가 저해됨을 확인하였다. 피부장벽기능 개선의 지표로써 filaggrin, involucrin, loricirn의 mRNA 발현 정도와 filaggrin, involucrin, loricirn의 생성량을 확인한 결과 에모딘 농도에 의존적으로 증가하는 우수한 결과가 얻어졌다. 특히 20 μM 농도에서 대조군 대비 2배의 생성량 증가를 보인 filaggrin은 천 연보습인자인 NMF의 형성에 관계되는 단백질로 각질층의 보습에 중요한 역할을 하는 것으로 알려져 있다. 결론적으로 emodin의 피부 질환 및 기능성 소재로서의 활용 가능성 중 염증 개선 및 피부장벽기 능 개선 소재로 활용될 수 있음을 확인하였으며 향후 추가적인 연구가 수행되면 그 활용 범위가 더 넓 어질 수 있을 것으로 사료된다.

In this study, acoustic and viscosity data are collected in real time during the ball milling process and analyzed for correlation. After fast Fourier transformation (FFT) of the acoustic data, changes in the signals are observed as a function of the milling time. To analyze this quantitatively, the frequency band is divided into 1 kHz ranges to obtain an integral value. The integrated values in the 2–3 kHz range of the frequency band decrease linearly, confirming that they have a high correlation with changes in viscosity. The experiment is repeated four times to ensure the reproducibility of the data. The results of this study show that it is possible to estimate changes in slurry properties, such as viscosity and particle size, during the ball milling process using an acoustic signal.

Macro-porous carbon foams are fabricated using cured spherical phenolic resin particles as a matrix and furfuryl alcohol as a binder through a simple casting molding. Different sizes of the phenolic resin particles from 100– 450 μm are used to control the pore size and structure. Ethylene glycol is additionally added as a pore-forming agent and oxalic acid is used as an initiator for polymerization of furfuryl alcohol. The polymerization is performed in two steps; at 80oC and 200oC in an ambient atmosphere. The carbonization of the cured body is performed under Nitrogen gas flow (0.8 L/min) at 800oC for 1 h. Shrinkage rate and residual carbon content are measured by size and weight change after carbonization. The pore structures are observed by both electron and optical microscope and compared with the porosity results achieved by the Archimedes method. The porosity is similar regardless of the size of the phenolic resin particles. On the other hand, the pore size increases in proportion to the phenol resin size, which indicates that the pore structure can be controlled by changing the raw material particle size.

Ni(OH)2 hollow spheres have been prepared by solvent displacement crystallization using a micro-injection device, and the effect of process parameters such as concentration and the relative ratio of the injection speed of the precursor solution, which is an aqueous solution of NiSO4·6H2O, to isopropyl alcohol of displacement solvent have been investigated. The crystal phases after NaOH treatment are in the β-phase for all process parameters. A higher concentration of NiSO4·6H2O aqueous solution is injected by a micro-injection device and bigger Ni(OH)2 hollow spheres with a narrower particle size distribution are formed. The crystallinity and hardness of the as-obtained powder are so poor that hydrothermal treatment of the as-obtained Ni(OH)2 at 120oC for 24 h in distilled water is performed in order to greatly improve the crystallinity. It is thought that a relative ratio of the injection speed of NiSO4·6H2O to that of isopropyl alcohol of at least more than 1 is preferable to synthesize Ni(OH)2 hollow spheres. It is confirmed that this solution- based process is very effective in synthesizing ceramic hollow spheres by simple adjustment of the process parameters such as the concentration and the injection speed.

We have examined the co-doping effects of 1/2mol% NiO and 1/4mol% Cr2O3 (Ni:Cr=1:1) on the reaction,microstructure, and electrical properties, such as the bulk defects and the grain boundary properties, of ZnO-Bi2O3-Sb2O3 (ZBS;Sb/Bi=0.5, 1.0, and 2.0) varistors. The sintering and electrical properties of Ni,Cr-doped ZBS, ZBS(NiCr) varistors werecontrolled using the Sb/Bi ratio. Pyrochlore (Zn2Bi3Sb3O14), α-spinel (Zn7Sb2O12), and δ-Bi2O3 were detected for all ofcompositions. For the sample with Sb/Bi=1.0, the Pyrochlore was decomposed and promoted densification at lowertemperature by Ni rather than by Cr. A homogeneous microstructure was obtained for all of the samples affected by α-spinel.The varistor characteristics were not dramatically improved (non-linear coefficient, α=5~24), and seemed to formZni..(0.17eV) and Vo.(0.33eV) as dominant defects. From impedance and modulus spectroscopy, the grain boundaries werefound to have been divided into two types, i.e., one is tentatively assigned to ZnO/Bi2O3 (Ni,Cr)/ZnO (0.98eV) and the otheris assigned to a ZnO/ZnO (~1.5eV) homojunction.

In this study we aimed to examine the co-doping effects of 1/6mol% Co3O4 and 1/4mol% Cr2O3 (Co:Cr=1:1)on the reaction, microstructure, and electrical properties, such as the bulk defects and the grain boundary properties, of ZnO-Bi2O3-Sb2O3 (ZBS; Sb/Bi=0.5, 1.0, and 2.0) varistors. The sintering and electrical properties of Co,Cr-doped ZBS, ZBS(CoCr)varistors were controlled using the Sb/Bi ratio. Pyrochlore (Zn2Bi3Sb3O14), α-spinel (Zn7Sb2O12), and δ-Bi2O3 were formed inall systems. Pyrochlore was decomposed and promoted densification at lower temperature on heating in Sb/Bi=1.0 by Cr ratherthan Co. A more homogeneous microstructure was obtained in all systems affected by α-spinel. In ZBS(CoCr), the varistorcharacteristics were improved (non-linear coefficient, α=20~63), and seemed to form Zni..(0.20eV) and Vo.(0.33eV) asdominant defects. From impedance and modulus spectroscopy, the grain boundaries were found to be composed of anelectrically single barrier (0.94~1.1eV) that is, however, somewhat sensitive to ambient oxygen with temperature. The phasedevelopment, densification, and microstructure were controlled by Cr rather than by Co but the electrical and grain boundaryproperties were controlled by Co rather than by Cr.

We aimed to examine the co-doping effects of 1/6mol% Mn3O4 and 1/4mol% Cr2O3 (Mn:Cr=1:1) on the reaction,microstructure, and electrical properties, such as the bulk defects and grain boundary properties, of ZnO-Bi2O3-Sb2O3 (ZBS;Sb/Bi=0.5, 1.0, and 2.0) varistors. The sintering and electrical properties of Mn,Cr-doped ZBS, ZBS(MnCr) varistors werecontrolled using the Sb/Bi ratio. Pyrochlore (Zn2Bi3Sb3O14), α-spinel (Zn7Sb2O12), and δ-Bi2O3 (also β-Bi2O3 at Sb/Bi≤1.0)were detected for all of the systems. Mn and Cr are involved in the development of each phase. Pyrochlore was decomposedand promoted densification at lower temperature on heating in Sb/Bi=1.0 system by Mn rather than Cr doping. A morehomogeneous microstructure was obtained in all systems affected by α-spinel. In ZBS(MnCr), the varistor characteristics wereimproved dramatically (non-linear coefficient, α=40~78), and seemed to form Vo.(0.33eV) as a dominant defect. Fromimpedance and modulus spectroscopy, the grain boundaries can be seen to have divided into two types, i.e. one is tentativelyassigned to ZnO/Bi2O3 (Mn,Cr)/ZnO (0.64~1.1eV) and the other is assigned to the ZnO/ZnO (1.0~1.3eV) homojunction.

TiO2 thin films consisting of positively charged poly(diallyldimethylammonium chloride)(PDDA) and negatively charged titanium(IV) bis(ammonium lactato) dihydroxide(TALH) were successfully fabricated on glass beads by a layer-by-layer(LBL) self-assembly method. The glass beads used here showed a positive charge in an acid range and negative charge in an alkaline range. The glass beads coated with the coating sequence of(PDDA/TALH)n showed a change in the surface morphology as a function of the number of bilayers. When the number of bilayers(n) of the(PDDA/TALH) thin film was 20, Ti element was observed on the surface of the coated glass beads. The thin films coated onto the glass beads had a main peak of the (101) crystal face and were highly crystallized with XRD diffraction peaks of anatase-type TiO2 according to an XRD analysis. In addition, the TiO2 thin films showed photocatalytic properties such that they could decompose a methyl orange solution under illumination with UV light. As the number of bilayers of the(PDDA/TALH) thin film increased, the photocatalytic property of the TiO2-coated glass beads increased with the increase in the thin film thickness. The surface morphologies and optical properties of glass beads coated with TiO2 thin films with different coating numbers were measured by field emission scanning electron microscopy(FE-SEM), X-ray diffraction(XRD) and by UV-Vis spectrophotometry(UV-vis).

Insoluble catalytic electrodes were fabricated by RF magnetron sputtering of Pt on Ti substrates and the performance of seawater electrolysis was compared in these electrodes to that is DSA electrodes. The Pt-sputtered insoluble catalytic electrodes were nearly 150 nm-thick with a roughness of 0.18μm, which is 1/660 and 1/12 of these values for the DSA (dimensionally stable anodes) electrodes. The seawater electrolysis performance levels were determined through measurements of the NaOCl concentration, which was the main reaction product after electrolysis using artificial seawater. The NaOCl concentration after 2 h of electrolysis with artificial seawater, which has 3.5% NaCl normally, at current densities of 50, 80 and 140 mA/cm2 were 0.76%, 1.06%, and 2.03%, respectively. A higher current density applied through the electrodes led to higher electrolysis efficiency. The efficiency reached nearly 58% in the Pt-sputtered samples after 2 h of electrolysis. The reaction efficiency of DSA showed higher values than that of the Pt-sputtered insoluble catalytic electrodes. One plausible reason for this is the higher specific surface area of the DSA electrodes; the surface cracks of the DSAs resulted in a higher specific surface area and higher reaction sites. Upon the electrolysis process, some Mg- and Ca-hydroxides, which were minor components in the artificial seawater, were deposited onto the surface of the electrodes, resulting in an increase in the electrical resistances of the electrodes. However, the extent of the increase ranged from 4% to 7% within an electrolysis time of 720 h.

Most TCOs such as ITO, AZO(Al-doped ZnO), FTO(F-doped SnO2) etc., which have been widely used in LCD,touch panel, solar cell, and organic LEDs etc. as transparent electrode material reveal n-type conductivity. But in order to realizetransparent circuit, transparent p-n junction, and introduction of transparent p-type materials are prerequisite. Additionalprerequisite condition is optical transparency in visible spectral region. Oxide based materials usually have a wide optical band-gap more than ~3.0eV. In this study, single-phase transparent semiconductor of SrCu2O2, which shows p-type conductivity, havebeen synthesized by 2-step solid state reaction at 950oC under N2 atmosphere, and single-phase SrCu2O2 thin films of p-typeTCOs have been deposited by RF magnetron sputtering on alkali-free glass substrate from single-phase target at 500oC, 1%H2/(Ar+H2) atmosphere. 3% H2/(Ar+H2) resulted in formation of second phases. Hall measurements confirmed the p-typenature of the fabricated SrCu2O2 thin films. The electrical conductivity, mobility of carrier and carrier density 5.27×10−2S/cm,2.2cm2/Vs, 1.53×1017/cm3 a room temperature, respectively. Transmittance and optical band-gap of the SrCu2O2 thin filmsrevealed 62% at 550nm and 3.28eV. The electrical and optical properties of the obtained SrCu2O2 thin films deposited by RFmagnetron sputtering were compared with those deposited by PLD and e-beam.

The influences of Na and K content on the crystal phase, the microstructure and the electrical property of BaTiO3-based thermistors was found to show typical PTC effects. The crystal phase of powder calcined at 1000˚C for 4hrs showed a single phase with BaTiO3, and the crystal structure was transformed from tetragonal to cubic phase according to added amounts of Na and K. In XRD results at 43˚~47˚, the (Ba0.858Na0.071K0.071)(Ti0.9985Nb0.0015)O3-δ showed (002) and (200) peaks but the (Ba0.762Na0.119K0.119)(Ti0.9975Nb0.0025)O3-δ showed (002), (020) and (200) peaks. In sintered bodies, those calcined at 600˚C rather than at 1000˚C were dense, and for certain amounts of Na and K showed rapid decreases in grain size. In relative permittivity, the curie temperature due to the transformation of ferroelectric phase rose with added Na and K but decreased in terms of relative permittivity. In the result of the R-T curve, the sintered bodies have curie temperatures of about 140˚C and the resistivity of sintered bodies have scores of Ω·cm; the jump order of sintered bodies was shown to be more than 104 in powder calcined at 1000˚C.

본 연구에서는 백산차추출물의 항산화 활성을 알아보기 위해 추출방법을 달리한 4가지 추출물인 열수추출물 (LPW), 고온가압추출물(LPA), 초음파추출물(LPU), 70% 에탄올 추출물추출(LPE)과 LPE에 대한 4가지 용매 층 분획 물인 n-hexane 층(LPE/H), ethyl acetate 층(LPE/E), n-butanol 층(LPE/B), water 층(LPE/W) 분획물의 DPPH와 ABTS 라디 칼 소거 활성을 측정하였다. 또한 백산차 추출물의 항염 활성을 알아보기 위해 LPS로 자극된 Raw 264.7 대식세포에서 LPE와 LPE/H, LPE/E, LPE/B, LPE/W의 NO, PGE2, TNF- α, IL-1β, IL-6의 생성 저해 활성을 측정하였다. 그 결과, DPPH와 ABTS 라디칼 소거 활성에서 LPE가 1,000 μg/mL 의 농도에서 각각 82.3%와 99.8%의 소거 활성을 나타내었으며, LPE/E의 경우 1,000 μg/mL의 농도에서 각각 91.8%와 99.6%의 높은 소거 활성을 나타내었다. 항염 활성 확인을 위하여 먼저 MTT assay를 수행하였으며 25 μg/mL 농도에서 LPE와 LPE/E 모두 90% 이상의 세포 생존율이 확인 되었다. NO와 PGE2의 생성 저해 활성을 분석한 결과, LPE 와 LPE/E에서 높은 NO와 PGE2 저해 활성을 확인 하였다. LPE는 25 μg/mL의 농도에서 각각 50%와 70%의 저해 활성 을 나타내었고 LPE/E는 같은 농도에서 각각 57%와 73%의 저해 활성을 나타내었다. 마지막으로 TNF-α, IL-1β, IL-6의 생성 저해 활성을 측정한 결과 LPE 및 LPE/E의 농도의존적인 저해 활성을 확인 하였으며 LPE가 25 μg/mL의 농도에서 각각 24%, 47%, 40%의 저해 활성을 나타내었다. 특히 LPE/E는 같은 농도에서 각각 51%, 57%, 62%의 높은 저해 활성을 보였다. 이러한 결과들로부터 1,000 μg/mL 농도의 LPE 및 LPE/E는 비타민C와 유사한 DPPH 및 ABTS 라디칼 소거능을 가지며 비교적 낮은 농도인, 25 μg/mL 농도에서 도 높은 항염증 활성을 가지고 있는 것으로 결론을 내릴 수 있다. 따라서 추후 항노화, 항균, 미백 활성 등에 대한 더 많은 연구 진행이 이루어진다면 백산차추출물은 염증성 질환의 예방 및 치료와 기능성 식품, 화장품 분야 등에서 효과적인 소재로 활용될 수 있을 것으로 사료된다.

지모를 70% methanol로 침지 추출하여 얻어진 추출물에 대해 n-hexane, EtOAc 및 n-BuOH로 순차 용매 분획하였고, 얻어진 결과물에 대하여 DPPH 및 ABTS+ radical 소거능 및 pancreatic lipase 저해활성을 평가하였다. DPPH 라디칼소거능은 페놀성 화합물의 함량이 상대적으로 높은 n-BuOH 층의 1000 mg/ml의 시험농도에서는 91.2%의 라디칼 소거능을 확인하였고, 지모 추출물에 존재하는 페놀성화합물이 라디칼 소거능과의 연관성을 시사하였다. 또한 ABTS+ 라디칼 소거능은 EtOAc층이 IC50 = 20.5±1.7 mg/ml, n-BuOH 층이 IC50 = 50.7±07 mg/ml의 활성이 확인 되었고, 강한 활성물질의 존재가 시사되었다. 또한, pancreatic lipase 저해활성을 측정한 결과, 강한 ABTS+ 라디칼 소거능을 나타낸 EtOAc 층의 IC50은 31.3±0.1 mg/ml의 저해율을 나타내었으며 이는 대조군인 orlistat에 비해 약하나 단일물질로 정제할 경우 더욱 강한 효능의 화합물이 존재할 가능성이 있음을 보여준다. 오일의 형태로 얻어진 n-hexane 분획층은 항산화 활성 및 pancreatic lipase 저해 활성을 거의 나타내지않았다. 향후 이들 활성물질 동정을 통한 활성 기작에 대한 연구가 필요하며 본 연구결과는 보다 우수한 라디칼 소거능 및 pancreatic lipase 저해능을 가지는 새로운 선도화합물발굴을 위한 기초자료로 활용가능하리라 사료된다.