본 논문은 새 정부의 사회통합 노력이 실질적인 성과를 내기 위해, 예 수 시대의 통치 이념이었던 팍스-로마나를 비판적으로 분석하고 현대적 대안을 모색한다. 팍스-로마나는 군사력과 경제적 착취에 기반한 지배층 만의 ‘위장된 평화’였으며, 본고는 이를 사회적 성서해석을 통해 피지배 층인 ‘아래로부터의 관점’에서 재평가한다. 팍스-로마나에 대해 예수는 억압적 지배체제라고 비판하며, 섬김, 평등, 연대성에 기초한 ‘횡적 공동 체’라는 대안적 현실을 제시했다. 그는 사회적 약자와의 연대, 착취 없는 경제 정의, 그리고 억압으로 목소리를 잃은 이들의 인격 회복을 통해 진 정한 평화체제를 추구했다. 결론적으로, 오늘날 진정한 사회통합을 위해 다음을 제안한다. 첫째, 누가 이 정책의 피해자인지 끊임없이 질문하며 약자를 우선해야 한다. 둘째, 소외를 낳는 경제 구조를 극복해야 한다. 셋째, 약자의 목소리가 보장되는 소통 구조를 만들어야 한다. 넷째, 연대 의 리더십으로 폭력의 순환을 끊어야 한다. 다섯째, 희생자가 주도권을 갖고 개혁해야 한다.

Organic-inorganic hybrid coating films have been used to increase the transmittance and enhance the physical properties of plastic substrates. Sol-gel organic-inorganic thin films were fabricated on polymethylmethacrylate (PMMA) substrates using a dip coater. Metal alkoxide precursor tetraethylsilicate (TEOS) and alkoxy silanes including decyltrimethoxysilane (DTMS), 3-glycidoxypropyltrimethoxysilane (GPTMS), phenyltrimethoxysilane (PTMS), 3-(trimethoxysilyl)propyl methacrylate (TMSPM) and vinyltrimethoxysilane (VTMS) were used to synthesize sol-gel hybrid coating solutions. Sol-gel synthesis was confirmed by the results of FT-IR. Cross-linking of the Si-O-Si network during synthesis of the sol-gel reaction was confirmed. The effects of each alkoxy silane on the coating film properties were investigated. All of the organicinorganic hybrid coatings showed improved transmittance of over 90 %. The surface hardness of all coating films on the PMMA substrate was measured to be 4H or higher and the average thickness of the coating films was measured to be about 500 nm. Notably, the TEOS/DTMS coating film showed excellent hydrophobic properties, of about 97°.

This study conducted the experiment for the development of the low pressure type SCR system. The experimental equipment of SCR system was installed, which was widely used as the nitrogen oxides abatement system, and the demonstration experiment was conducted to see that it met the Tier III regulation according to the IMO NOx Technical Code. The SCR system demonstration experiment was divided into three stages: SCR system component operation test, engine parameter test by engine load, and NOx abatement performance and ammonia slip verification test. The final performance of the SCR system was verified through analysis of NOx abatement performance and ammonia slip test results for each load variation.

General D-glass(Dielectric glass) fibers are adaptable to PCBs(Printed circuit boards) because they have a low dielectric constant of about 3.5~4.5. However, very few papers have appeared on the physical characteristics of D-glass fibers. D-glass fibers were fabricated via continuous spinning process using bulk D-glass. In order to fabricate the D-glass, raw materials were put into a Pt crucible, melted at 1650℃ for 2 hrs, and then annealed at 521 ± 10℃ for 2 hrs. We obtained transparent clear glass. The transmittance and adaptable temperature for spinning of the bulk marble glass were characterized using a UV-visible spectrometer and a viscometer. Continuous spinning was carried out using direct melting spinning equipment as a function of the fiberizing temperature in the range of 1368℃ to 1460℃, while the winder speed was between 100 rpm and 200 rpm. We investigated the physical properties of the D-glass fibers. The average diameters of the glass fibers were measured by optical microscope and FE-SEM. The average diameters of the D-glass fibers were 21.36 um at 100 rpm and 34.06 um at 200 rpm. The mechanical properties of the fibers were confirmed using a UTM(Universal materials testing machine). The average tensile strengths of the D-glass fibers were 467.03 MPa at 100 rpm and 522.60 MPa at 200 rpm.

E-glass (electrical glass) fiber is the widely used as a reinforced composite material of PCBs (printed circuit boards). However, E-glass fiber is not stable because it has a dielectric constant of 6~7. On the other hand, D-glass (dielectric glass) fiber has a low dielectric constant of 3~4.5. Thus, it is adaptable for use as a reinforcing material of PCBs. In this study, we fabricated D-glass compositions with low dielectric constant, and measured the electrical and optical properties. In the glass composition, the boron content was changed from 9 to 31 wt%. To confirm the dependence of the dielectric constant on melting properties, D-glass with 22 wt% boron was melted at 1550 oC and 1650 oC for 2hrs. The glass melted at 1650 oC had a lower dielectric constant than the glass melted at 1550 oC. Therefore, the D-glass with boron of 9~31 wt% was fabricated by melting at 1650 oC for 2hrs, and transparent clear glass was obtained. We identified the non-crystalline nature of the glass using an XRD (x-ray diffractometer) graph. The visible light transmittance values depending on the boron contents were measured and found to be 88.6%~ 82.5%. Finally, the dielectric constant of the D-glass with 31 wt% boron was found to have decreased from 4.18 to 3.93.

The effect of titanium dioxide (TiO2) on the properties of color conversion glasses was examined for glasses based on BaO-ZnO-B2O3-SiO2. One glass sample, containing 25 mol% of each component, was used as a reference; the other three glass samples contained 1, 3, and 5 mol% TiO2, respectively. The four color conversion glass samples were prepared by sintering a mixture of glass frits and a YAG:Ce+ phosphor. The characteristics of the color conversion glass samples, such as luminous efficacy, luminance, CIE (Commission International de I'Eclairage) chromaticity, CCT (Correlated Color Temperature), and CRI (Color Rendering Index) were analyzed according to the PL spectrum. The refractive index of the glass samples was found to increase with the titanium dioxide content. In conclusion, luminous efficacy of color conversion glasses increased as the content of TiO2 was raised in the glass matrix.

For the purpose of improving the durability problem, translucent opal glass was fabricated as a substitute for the polycarbonate diffuser of LED lighting. Calcium phosphate was used as an opacifier of opal glass and melted in an electric furnace. The opaque effect was identified according to the change of the cooling procedure. As results, translucent opal glass was obtained by the melting of a batch with a composition of 3.8% calcium phosphate at 1550˚C for 2 hrs and then the cooling of the material in the furnace. For the cooling condition of the glass sample, HTCG (High Temperature Cooled Glass) was found to have better optical properties than LTAG (Low Temperature Annealed Glass). It had excellent optical properties for a diffuser of LED lighting, with no dazzling from direct light due to its high haze value of over 99% and low parallel transmittance value of under 1%. For the thermal properties, it had an expressed thermal expansion coefficient of 5.7×10-6/˚C and a softening point of 876˚C; it also had good thermal properties such as good thermal shock resistance and was easy to apply to the general manufacturing process in the forming of glass tubes and bulbs. Therefore, it is concluded that this translucent opal glass can be used as a glass diffuser material for LED lighting with high heat resistance and high durability; this material is suitable as a substitute for polycarbonate diffusers.

The quartz glasses were prepared by sintering of fumed silica powders and the effect of OH concentration on their surface on sintering was studied. Through the firing process, the fumed silica was crystallized from 1180 to region. The amount of hydroxyl group decreased with increase in calcination temperature and consequently the crystallization was prevented. A transparent quartz glass was obtained from fumed silica, previously calcined at , by the sintering at for 1 h.