Domestic commercial low- and intermediate-level radioactive waste storage containers are manufactured using 1.2 mm thick cold-rolled steel sheets, and the outer surface is coated with a thin layer of primer of 10~36 μm. However, the outer surface of the primer of the container may be damaged due to physical friction, such as acceleration, resonance, and vibration during transportation. As a result, exposed steel surfaces undergo accelerated corrosion, reducing the overall durability of the container. The integrity of storage containers is directly related to the safety of workers. Therefore, the development of storage containers with enhanced durability is necessary. This paper provides an analysis of mechanical properties related to the durability of WC (tungsten carbide)-based coating materials for developing low- and intermediate-level radioactive waste storage containers. Three different WC-based coating specimens with varied composition ratios were prepared using HVOF (high-velocity oxy-fuel) technique. These different specimens (namely WC-85, WC-73, and WC-66) were uniformly deposited on cold-rolled steel surfaces ensuring a constant thickness of 250 μm. In this work, the mechanical properties of the three different WCbased coaitng materials evaluated from the viewpoints of microstructure, hardness, adheision force between substrate and coating material, and wear resistance. The cross-sectional SEM-EDS (Scanning Electron Microscope-Energy Dispersive X-ray Spectroscopy) images revealed that elements W (tungsten), C (carbon), Ni (nickel), and Cr (chromium) were uniformly distributed within the each coating layers which was approximately 250 μm thick. The average hardness values of HWC-85 and HWC-73 were found to be 1,091 Hv (Vickers Hardness) and 1,083 Hv, respectively, while the HWC-66 exhibited relatively lower hardness value of 883 Hv. This indicates that a higher WC content results in increased hardness. Adhesion force between and substrates and coating materials exceeded 60 MPa for all specimens, however, there were no significant differences observed based on the tungsten carbide content. Furthermore, a taber-type abrasion tester was used for conducting abrasion resistance tests under specific conditions including an H-18 load weight at 1,000 g with rotational speed set at 60 RPM. The abrasion resistance tests were performed under ambient temperatures (RT: 23±2°C) as well as relative humidity levels (RH: 50±10%). Currently, the ongoing abrasion resistance tests will include some results in this study.

This study focuses on the development of coatings designed for storage containers used in the management of radioactive waste. The primary objective is to enhance the shielding performance of these containers against either gamma or neutron radiation. Shielding against these types of radiation is essential to ensure the safety of personnel and the environment. In this study, tungsten and boron cabide coating specimens were manufactured using the HVOF (High-Velocity Oxy Fuel) technuqe. These coatings act as an additional layer of protection for the storage containers, effectively absorbing and attenuating gamma and neutron radiation. The fabricated tungsten and boron carbide coating specimens were evaluated using two different testing methods. The first experiment evaluates the effectiveness of a radiation shielding coating on cold-rolled steel surfaces, achieved by applying a mixture of WC (Tungsten Carbide) powders. WC-based coating specimens, featuring different ratios, were prepared and preliminarily assessed for their radiation shielding capabilities. In the gamma-ray shielding test, Cs-137 was utilized as the radiation source. The coating thickness remained constant at 250 μm. Based on the test results, the attenuation ratio and shielding rate for each coated specimen were calculated. It was observed that the gammaray shielding rate exhibited relatively higher shielding performance as the WC content increased. This observation aligns with our findings from the gamma-ray shielding test and underscores the potential benefits of increasing the tungsten content in the coating. In the second experiment, a neutron shielding material was created by applying a 100 μm-thick layer of B4C (Boron Carbide) onto 316SS. The thermal neutron (AmBe) shielding test results demonstrated an approximate shielding rate of 27%. The thermal neutron shielding rate was confirmed to exceed 99.9% in the 1.5 cm thick SiC+B4C bulk plate. This indicates a significant reduction in required volume. This study establishes that these coatings enhance the gamma-ray and neutron shielding effectiveness of storage containers designed for managing radioactive waste. In the future, we plan to conduct a comparative evaluation of the radiation shielding properties to optimize the coating conditions and ensure optimal shielding effectiveness.

There are many types of foam molding methods. The most commonly used methods are the pressure foaming method, in which foam resin is mixed with a foaming agent at high temperature and high pressure, and the normal pressure foaming method, which foams at high temperature without pressure. The polymer resins used for foaming have different viscosities. For foaming under normal pressure, they need to be designed and analyzed for optimal foaming conditions, to obtain resins with low melt-viscosity or a narrow optimal viscosity range. This study investigated how changes in viscosity, molding temperature, and cross-link foaming conditions affected the characteristics of the molded foam, prepared by blending rubber polymer with biodegradable resin. The morphologies of cross sections and the cell structures of the normal pressure foam were investigated by SEM analysis. Properties were also studied according to cross-link/foaming conditions and torque. Also, the correlation between foaming characteristics was studied by analyzing tensile strength and elongation, which are mechanical properties of foaming composites.

Natural radionuclides-containing substances (NORM) contain natural radionuclides and cause radiation exposure. In Korea, safety management measures were needed to deal with and dispose of radon mattresses containing monazite in relation to such NORM. However, there is no clear safety management system related to NORM waste in Korea. In order to manage this reasonably and systematically, it is necessary to investigate and analyze standards and management measures related to the treatment and disposal of NORM waste. Therefore, this study investigated and analyzed the exemption and clearance level of NORM waste regulations in international organizations and foreign countries. IAEA GSR Part 3, 2013/59/Euratom, ANSI/HPS N13.53, CRCPD SSRCR Part N, and ARPANSA Publications 15 safety management regulations were analyzed to investigate safety management standards for NORM waste. The exemption and clearance level in international organizations and foreign countries were compared and analyzed based on radioactive concentration and dose. In addition, the management measures proposed for each literature were also investigated. As a result of the analysis, IAEA GSR Part 3 applied 1 mSv as a regulatory exemption level, 1 Bq/g for uranium and thorium series as a clearance level, and 10 Bq/g for K-40 nuclides. The IAEA recommends a differential approach to the potential and scale of exposure. The EU applied 1 Bq/g to uranium and thorium families and 10 Bq/g to K-40 nuclides for both regulatory exemption and clearance levels. The EU recommended that it be managed in proportion to the scale and likelihood of exposure as a result of the action. It is analyzed that this is similar to the IAEA’s management plan. In the United States, there was no single federal government radioactive concentration and dose for NORM management. The management plan differed in management status and level from state to state, and K-40 was excluded from regulation unless it was intentionally enriched. In the case of Australia, the radioactive concentration of uranium and thorium was 1 Bq/g as a standard for regulatory exemption and 1 mSv as a dose. As a management plan, it was suggested to dispose of waste by means of accumulation, dilution/dispersion, and reclamation. It was also suggested that the scale of exposure, like international organizations, take into account the possibility. The results of this study are believed to be used as basic data for presenting domestic NORM waste treatment and disposal methods in the future.

In this study, radioactivity of Cs-134, Cs-137, and Eu-154, which are gamma-emitting nuclides among fission products of spent fuel, was analyzed as a tool to measure the burnup of spent fuel nondestructively. This nuclide has a unique gamma-ray energy, allowing the amount of the isotope to be estimated based on the intensity of the gamma-ray at a specific energy. The SCALE 6.2 ORIGAMI (ORIGen AsseMbly Isotopics) module and the latest ORIGEN-arp library were used for computational analysis. The spent fuel samples were selected as WH14×14 with an enrichment of 1.5~5.0wt%, a burnup of 10~60 GWD/MTU, and a cooling time of 0~40 years. The analysis results were benchmarked using SFCOMPO experimental data provided by OECD/ NEA, including isotope inventory and uncertainty measured by destructive radiochemical analysis, fuel assembly design data required for benchmark model development, reactor design information, and operating history information. 16 similar spent fuels were selected from SFCOMPO data and the calculation results of Cs-134, Cs-137, and Eu-154 were compared. The average error of the Cs-134 radioactivity calculation result was 2.81%, and the maximum error was 6.70%. The average errors of Cs-137 and Eu-154 were 2.42% and 4.95%, respectively, and the maximum errors were 5.40% and 14.91%, respectively.

Acacetin, which is present in damiana (Turnera diffusa ) and black locust (Robinia pseudoacacia ), has several pharmacologic activities such as antioxidant, anti-inflammatory, and anti-proliferative effects on cancer cells. However, the effect of acacetin on head and neck cancers has not been clearly established. This study aimed to examine the effects of acacetin on cell growth and apoptosis induction in FaDu human pharyngeal carcinoma cells. These were investigated by 3-[4,5-dimethylthiazol-2-yl]-2,5-diphenyltetrazolium bromide assay, Live/Dead cell assay, 4′,6-diamidino-2-phenylindole dihydrochloride staining, caspase-3 and caspase-7 activation assay, and immunoblotting in FaDu cells. Acacetin induced FaDu cell death in a dose-dependent manner, with an estimated IC50 value of 41.9 µM, without affecting the viability of L-929 mouse fibroblasts as normal cells. Acacetin treatment resulted in nuclear condensation in the FaDu cells. It promoted the proteolytic cleavage of procaspase-3, -7, -8, and -9 with increasing amounts of the cleaved caspase isoforms in FaDu cells. Acacetin-induced apoptosis in FaDu cells was mediated by the expression of Fas and activation of caspase-8, caspase-3, and poly (ADP-ribose) polymerase. Immunoblotting showed downregulation of the anti-apoptotic mitochondrial proteins Bcl-2 and Bcl-xL, but upregulation of the mitochondria-dependent pro-apoptotic proteins Bax and Badin FaDu cells after acacetin treatment. These findings indicate that acacetin inhibits cell proliferation and induces apoptotic cell death in FaDu human pharyngeal carcinoma cells via both the death receptor-mediated extrinsic apoptotic pathway and the mitochondria-mediated intrinsic apoptotic pathway.

Resveratrol (3,4',5,-trihydroxystilbene), a phytoalexin present in grapes, exerts a variety of actions to reduce superoxides, prevents diabetes mellitus, and inhibits inflammation. Resveratrol acts as a chemo-preventive agent and induces apoptotic cell death in various cancer cells. However, the role of resveratrol in odontoblastic cell differentiation is unclear. In this study, the effect of resveratrol on regulating odontoblast differentiation was examined in MDPC-23 mouse odontoblastic cells derived from mouse dental papilla cells. Resveratrol significantly accelerated mineralization as compared with the control culture in differentiation of MDPC-23 cells. Resveratrol significantly increased expression of ALP mRNA as compared with the control in differentiation of MDPC-23 cells. Resveratrol significantly accelerated expression of ColⅠmRNA as compared with the control in differentiation of MDPC-23 cells. Resveratrol significantly increased expressions of DSPP and DMP-1 mRNAs as compared with the control in differentiation of MDPC-23 cells. Treatment of resveratrol did not significantly affect cell proliferation in MDPC-23 cells. Results suggest resveratrol facilitates odontoblast differentiation and mineralization in differentiation of MDPC-23 cells, and may have potential properties for development and clinical application of dentin regeneration materials.

We demonstrated an effective way of preparing melt spinnable mesophase pitches via catalytic hydrogenation of petroleum residue (fluidized catalytic cracking-decant oil) and their subsequent thermal soaking. The mesophase pitches thus obtained were analyzed in terms of their viscosity, elemental composition, solubility, molecular weight, softening point and optical texture. We found that zeolite-induced catalytic hydrogenation under high hydrogen pressure contributed to a large variation in the properties of the pitches. As the hydrogen pressure increased, the C/H ratio decreased, and the solubility in n-hexane increased. The mesophase pitch with entirely anisotropic domains of flow texture exhibited good meltspinnability. The mesophase carbon fibers obtained from the catalytically hydrogenated petroleum residue showed moderate mechanical properties.

Fe-6.5 wt.% Si alloys are widely known to have excellent soft magnetic properties such as high magnetic flux density, low coercivity, and low core loss at high frequency. In this work, disc-shaped preforms are prepared by spark plasma sintering at 1223 K after inert gas atomization of Fe-6.5 wt.% Si powders. Fe-6.5 wt.% Si sheets are rolled by a powder hot-rolling process without cracking, and their microstructure and soft magnetic properties are investigated. The microstructure and magnetic properties (saturation magnetization and core loss) of the hot-rolled Fe-6.5 wt.% Si sheets are examined by scanning electron microscopy, electron backscatter diffraction, vibration sample magnetometry, and AC B–H analysis. The Fe-6.5 wt.% Si sheet rolled at a total reduction ratio of 80% exhibits good soft magnetic properties such as a saturation magnetization of 1.74 T and core loss (W5/1000) of 30.7 W/kg. This result is caused by an increase in the electrical resistivity resulting from an increased particle boundary density and the oxide layers between the primary particle boundaries.

Ski protein is a nuclear transcription factor that does not bind DNA directly. Due to its unique binding properties with multiple factors, Ski could perform various roles in the regulation of both cellular proliferation and differentiation. We had previously reported that Ski protein is present in granulosa cells of atretic follicles, but not in preovulatory follicles, suggesting that Ski has a role in apoptosis of granulosa cells. The alternative fate of granulosa cells other than apoptosis is to differentiate to luteal cells; however, it is unknown whether Ski is expressed and has a role in granulosa cells undergoing luteinization. Thus, the aim of the present study was to examine whether the initiation of luteinization with luteinizing hormone (LH) directly regulates expression of Ski in the luteinized granulosa and luteal cells after ovulation by in vitro models. RT-PCR and real time PCR analysis respectively revealed that LH had no effect on c-Ski mRNA expression in the cultured granulosa cells regardless of LH treatment. Though Ski protein isabsent in granulosa cells of preovulatory follicle, its mRNA(c-Ski) was expressed and the level was unchanged even after LH surge. Taken together, these results demonstrated that Ski protein expression is induced in granulosa cells upon luteinization, and suggested that its expression is regulated post-transcriptionally. Moreover, expression of mRNA of Arkadia, an E3 ubiquitin ligases, in luteinizing granulosa cells in vivo was assessed by real time-PCR. The levels of Arkadia mRNA expression were unchanged during follicular growth and post ovulatory luteinization. These findings suggest that Ski protein level may be regulated during luteinization at translational and/or post-translational level but not by Arkadia.

Sloan-Kettering virus gene product of a cellular pro-oncogene c-Ski is an unique nuclear pro-onco protein and belongs to the Ski/Sno proto-oncogene family. Ski plays multiple roles in a variety of cell types, it can induce both oncogenic transformation and terminal muscle differentiation when expressed at high levels. Ski protein is implicated in proliferation/differentiation in a variety of cells. The alternative fate of granulosa cells other than apoptosis is to differentiate to luteal cells, however, it is unknown whether Ski is expressed and has a role in granulosa cells undergoing luteinization. Thus, the aim of this study was, by means of immunohistochemical methods, to locate Ski protein in the rat ovaries during ovulation and corpora lutea(CL) formation to predict the possible involvement of Ski in luteinization. In addition, to examine whether the initiation of luteinization with luteinizing hormone(LH) directly regulates expression of Ski in the luteinized granulosa and luteal cells after ovulation by in vivo models. In order to examine the expression pattern of Ski protein along with the progress of luteinization, follicular growth was induced by administration of equine chorionic gonadtropin to immature female rat, and luteinization was induced by human chorionic gonadtropin treatment to mimic luteinizing hormone(LH) surge. While no Ski-positive granulosa cells were present in preovulatory follicle, Ski protein expression was induced in response to LH surge, and was maintained after the formation of corpus luteum(CL). These results indicate that Ski is profoundly expressed in the luteinized granulosa cells and luteal cells of CL during luteinization, and suggest that Ski may play a role in luteinization of granulosa cells.

For reconstituting genetic resource(Korean Native Chicken: KNC) with grem-line chimeric chicken made with cryopreserved biastdermal cells, the experiments were carried out to optimize cryopreservating conditions. Stage X biastdemal cells were collected from KNC embryos and dissociated. Cells were susupended in medium containing cyopretectant and fetal bovine serum(FBS), and distributed into plastic ampules. Cell susupensions were seeded to induce ice formation at — 7℃ to — 35℃ at in the experiments, the effect of modification of dissociation way, concentration of FBS and cell density on the vaibility of frezen-thawed cells were investigated by trypan blue exclusion. Then change the way of cell dissociation from pipetting to short time vortexing, viability of frozen- thawed cell tended to be increaced from 29 % to 52 %. Increase concentraition of FBS in frozen medium from 20 % to 80 % made viability of thawed cell from 28 % to 35 %. The viability of thawed cells were 33.9% frozen at 2 embryos/ 0.5 ml, and 43.6 % frozen at 20embryos/0.5 ml. Furthermore, combination of three modifications make big improvement. The viability of frozen-thawed cell was 60 % for combinated method, and 41 % for general method. This result means the advance to practical cryoreservation of blastdermal cell of the KNC(Ogolgye breed).

For reconstituting genetic resource(Korean Native Chicken: KNC) with grem-line chimeric chicken made with cryopreserved biastdermal cells, the experiments were carried out to optimize cryopreservating conditions. Stage X biastdemal cells were collected from KNC embryos and dissociated. Cells were susupended in medium containing cyopretectant and fetal bovine serum(FBS), and distributed into plastic ampules. Cell susupensions were seeded to induce ice formation at —7 ℃ to —35 ℃ at in the experiments, the effect of modification of dissociation way, concentration of FBS and cell density on the vaibility of frezen-thawed cells were investigated by trypan blue exclusion. Then change the way of cell dissociation from pipetting to short time vortexing, viability of frozen-thawed cell tended to be increaced from 29 % to 52 %. Increase concentraition of FBS in frozen medium from 20 % to 80 % made viability of thawed cell from 28 % to 35 %. The viability of thawed cells were 33.9% frozen at 2 embryos/ 0.5ml, and 43.6 % frozen at 20 embryos/0.5 ml. Furthermore, combination of three modifications make big improvement. The viability of frozen-thawed cell was 60 % for combinated method, and 41 % for general method. This result means the advance to practical cryoreservation of blastdermal cell of the KNC(Ogolgye breed).

This study is intended to examine the motor skill learning and treadmill exercise on motor performance and synaptic plasticity in the cerebellar injured rats by harmaline. Experiment groups were divided into four groups and assigned 15 rats to each group. GroupⅠ was a normal control group(induced by saline); GroupⅡ was a experimental control group(cerebellar injured by harmaline); GroupⅢ was a group of motor skill learning after cerebellar injured by harmaline; GroupⅣ was a group of treadmill exercise after cerebellar injured by harmaline. In motor performance test, the outcome of groupⅡ was significantly lower than the groupⅢ, Ⅳ(especially groupⅢ)(p<.001). In histological finding, the experimental groups were destroy of dendrities and nucleus of cerebellar neurons. GroupⅢ, Ⅳ were decreased in degeneration of cerebellar neurons(especially groupⅢ). In immunohistochemistric response of synaptophysin in cerebellar cortex, experimental groups were decreased than groupⅠ. GroupⅢ's expression of synaptophysin was more increased than groupⅡ, Ⅳ. In electron microscopy finding, the experimental groups were degenerated of Purkinje cell. These result suggest that improved motor performance by motor skill learning after harmaline induced is associated with dynamically altered expression of synaptophysin in cerebellar cortex and that is related with synaptic plasticity.

치과 콘빔 전산화단층 검사 시 갑상선 부위의 방사선 피폭선량을 최소화하기 위하여 보루스 (Bolus)를 이용한 차폐체를 제작하고, 방사선 차폐 효과와 영상의 적정성을 평가하였다. 치과용 콘빔 전산화단층검사 장비를 사용하여 치과방사선 두부 팬텀을 대상으로 갑상선의 좌, 우측 부위에 유리선량계를 부착시켜 방사선량을 측정하였다. 차폐체의 두께를 각각 10 mm, 20 mm, 30 mm로 다르게 하여 각 차폐체별로 흡수선량을 측정하여 차폐체를 사용하지 않았을 경우와 비교하였다. 8명의 평가자가 진료영상의 적정성을 여부를 평가하였다. 왼쪽 갑상선 부위에 30 mm Bolus 차폐체를 사용한 경우에는 결과값이 평균 342.67 μ㏉로 Bolu s 차폐체를 사용하지 않고 측정한 결과값의 평균 431.22 μ㏉보다 20.7% 감소하였고, 오른쪽 갑상선 부위에 30 mm Bolus 차폐체를 사용한 경우에는 평균 424.56 μ㏉로 21.9%의 선량감소효과를 보였다. 진료 영상의 적정성은 평가자 모두 사용 가능하다 판단하였다. 결론적으로, 치과 콘빔 전산화단층검사 시 갑상선 부위의 방사선 피폭선량을 최소화하기 위해 제작된 Bolus 차폐체는 장해음영 없이 적정한 진단 영상 처리가 가능하고, 방사선차폐 효과가 있어 유용한 차폐체로 적용 가능할 것으로 사료된다.

Advanced multidetector CT (MDCT) technology provides 2-dimensional (2D) images with 3-dimensional (3D) images. These 3D images (volume rendered, VR images) demonstrates the surface of the body and cutaneous neurofibromas in pa-tients with neurofibromatosis (NF) are well visualized. MDCT is a very useful imaging modality that represents various findings of neurofibromatosis such as cutaneous neurofibromas, central nervous tumors, skeletal anomalies including verte-bral scalloping and dural ectasia, mediastinal masses, lung parenchymal diseases, vascular anomalies, and complicated dis-eases related with NF. Herein, we report three cases with NF presenting cutaneous neurofibromas diagnosed by MDCT; One is NF patient with dural ectasis and meningocele, second case is a patient with NF and horseshoe kidney, third case is a pa-tient with cutaneous and subcutaneous neurofibromas.

Atrial fibrillation (AF) is a common, benign, and transient type of supraventricular arrhythmia encountered during the early postoperative period after a pulmonary resection. However, it sometimes might result in hemodynamic deterioration. We report on a case of new-onset atrial fibrillation in a 74-year-old male patient after right lower lobectomy, which was not controlled with intermittent bolus injection of esmolol and diltiazem. Successful pharmacological cardioversion was achieved with intravenous (6 mg/hr for 2 hours) followed by oral (90 mg q day) diltiazem 20 hours after this treatment. The literature on the risk factors and management of atrial fibrillation after pulmonary resection is reviewed.

We report on a rare case of a 26-year-old man with neurofibromatosis type I who presented with cramping abdominal pain caused by stones within a horseshoe kidney. He also showed extensive neurofibromas in his neck, thorax, and abdominopel-vic cavity. He had undergone excision of a subcutaneous neurofibroma from his left flank a few years prior. Treatment by extracorporeal shock wave lithotripsy (ESWL) was administered twice. Stones were removed completely and his symptoms were resolved.