During decommissioning and site remediation of nuclear power plant, large amount of wastes (including radioactive waste) with various type will be generated within very short time. Among those wastes, soil and concrete wastes is known to account for more than 70% of total waste generated. So, efficient management of these wastes is very essential for effective NPP decommissioning. Recently, BNS (Best System) developed a system for evaluation and classification of soil and concrete wastes from the generation. The system is composed of various modules for container loading, weight measurement, contamination evaluation, waste classification, stacking, storage and control. By adopting modular type, the system is good for dealing with variable situation where system capacity needs to be expanded or contracted depending on the decommissioning schedule, good for minimizing secondary waste generated during maintenance of failed part and also good for disassemble, transfer and assemble. The contamination evaluation module of the system has two sub module. One is for quick measurement with NaI(Tl) detector and the other is for accurate measurement with HPGe detector. For waste transfer, the system adopts LTS (Linear Transfer System) conveyor system showing low vibration and noise during operation. This will be helpful for minimizing scattering of dust from the waste container. And for real time positioning of waste container, wireless tag was adopted. The tag also used for information management of waste history from the generation. Once a container with about 100 kg of soil or concrete is loaded, it is moved to the weight measurement module and then it transfers to quick measurement module. When measured value for radioactivity concentration of Co- 60 and Cs-137 is more than 1.0 Bq/g, then the container is classified as waste for disposal and directly transferred to stacking and storage rack. Otherwise, the container is transferred to accurate measurement module. At the accurate module, the container is classified as waste for disposal or waste for regulatory clearance depending on the measurement result of 0.1 Bq/g. As the storage rack has a sections for disposal and regulatory clearance respectively, the classified containers will be positioned at one of the sections depending on the results from the contamination evaluation module. The system can control the movement of lots of container at the same time. So, the system will be helpful for the effective nuclear power plant decommissioning in view of time and budget.

In this study, four technologies were selected to treat river water, lake water, and groundwater that may be contaminated by tritium contaminated water and tritium outflow from nuclear power plants, performance evaluation was performed with a lab-scale device, and then a pilot-scale hybrid removal facility was designed. In the case of hybrid removal facilities, it consists of a pretreatment unit, a main treatment unit, and a post-treatment unit. After removing some ionic, particulate pollutants and tritium from the pretreatment unit consisting of UF, RO, EDI, and CDI, pure water (2 μS/cm) tritium contaminated water is sent to the main treatment process. In this treatment process, which is operated by combining four single process technologies using an inorganic adsorbent, a zeolite membrane, an electrochemical module and aluminumsupported ion exchange resin, the concentration of tritium can be reduced. At this time, the tritium treatment efficiency of this treatment process can be increased by improving the operation order of four single processes and the performance of inorganic adsorbents, zeolite membrane, electrochemical modules, and aluminum- supported ion exchange resins used in a single process. Therefore, in this study, as part of a study to increase the processing efficiency of the main treatment facility, the tritium removal efficiency according to the type of inorganic adsorbent was compared, and considerations were considered when operating the complex process.

Radioactive waste generated during decommissioning of nuclear power plants is classified according to the degree of radioactivity, of which concrete and soil are reclassified, some are discharged, and the rest is recycled. However, the management cost of large amounts of concrete and soil accounts for about 40% of the total waste management cost. In this study, a material that absorbs methyl iodine, a radioactive gas generated from nuclear power plants, was developed by materializing these concrete and soil, and performance evaluation was conducted. A ceramic filter was manufactured by forming and sintering mixed materials using waste concrete, waste soil, and by-products generated in steel mills, and TEDA was attached to the ceramic filter by 5wt% to 20wt% before adsorption performance test. During the deposition process, TEDA was vaporized at 95°C and attached to a ceramic filter, and the amount of TEDA deposition was analyzed using ICP-MS. The adsorption performance test device set experimental conditions based on ASTM-D3808. High purity nitrogen gas, nitrogen gas and methyl iodine mixed gas were used, the supply amount of methyl iodine was 1.75 ppm, the flow rate of gas was 12 m/min, and the supply of water was determined using the vapor pressure value of 30°C and the ideal gas equation to maintain 95%. Gas from the gas collector was sampled to analyze the removal efficiency of methyl iodine, and the amount of methyl iodine detected was measured using a methyl iodine detection tube.

During the operation of the nuclear power plant, various radioactive waste are generated. The spent resin, boron concentrates, and DAW are classified as a generic radioactive waste. They are treated and stored at radioactive waste building. In the reactor vessel, different types of radioactive waste are generated. Since the materials used in reactor core region exposed to high concentration of neutrons, they exhibit higher level of surface dose rate and specific activity. And they are usually stored in spent fuel pool with spent fuel. Various non-fuel radioactive wastes are stored in spent fuel pool, which are skeleton, control rod assembly, burnable neutron absorber, neutron source, in core detector, etc. The skeleton is composed of stainless 304 and Inconel-718. There are two types of control rod assembly, that are WH type and OPR type. The WH type control rod is composed of Ag-In-Cd composites. The OPR type control rod is composed of B4C and Inconel-625. In this paper, the characteristics and storage status of the non-fuel radioactive waste will be reported. Also, the management strategy for the various non-fuel radioactive waste will be discussed.

The removal of cesium (Cs) from contaminated clay minerals is still a challenge due to the limited efficiency of the process. Thus, this study aimed to enhance the removal for Cs+ ions during the conventional acid washing process by incorporating a bead-type adsorbent. Polyacrylonitrile-based nickel potassium hexacyanoferrate (NiFC-PAN) was utilized as the Cs adsorbent to selectively adsorb Cs+ ions in a strongly acidic solution that contained competing ions. To enable easy separation of clay particles and protect the adsorbent from harsh environmental conditions, PAN was deliberately constructed as large beads. The synthesized adsorbent (NiFC/PAN in a 2:1 ratio) displayed high selectivity for Cs+ ions and had a maximum capacity of 162.78 mg/g for Cs+ adsorption in 0.5 M HNO3 solution. Since NiFC-PAN exhibited greater Cs selectivity than the clay mineral (hydrobiotite, HBT), adding NiFC-PAN during the acid washing substantially increased Cs desorption (73.3%) by preventing the re-adsorption for Cs+ ions on the HBT. The acid treatment in the presence of NiFCPAN also significantly decreased the radioactivity of 137Cs-HBT from 209 to 27 Bq/g, resulting in a desorption efficiency of 87.1%. Therefore, these findings suggest that the proposed technique is a potentially useful and effective method for decontaminating radioactive clay.

Metakaolin-based geopolymers have shown promise as suitable candidates for 14C immobilization and final disposal. It has been shown that the physicochemical properties of metakaolin wasteforms meet, and often far exceeding, the strict compression strength and leaching acceptance criteria of the South Korea radioactive waste disposal site. However, it is not possible to analyze and characterize the internal structure of the geopolymer wasteform by conventional characterization techniques such as microscopy without destruction of the wasteform; an impractical solution for inspecting wasteforms destined for final disposal. Internal inspection is important for ensuring wastes are homogenously mixed throughout the wasteform and that the wasteform itself does not pose any significant defects that may have formed either during formulation and curing or as a result of testing prior to final disposal. X-ray Computed Tomography (XCT) enables Non-Destructive Evaluation (NDE) of objects, such as final wasteforms, allowing for both their internal and external, characterization without destruction. However, for accurate quantification of an objects dimensions the spatial resolution (length and volume measures) must be know to a high degree of precision and accuracy. This often requires extensive knowledge of the equipment being used, its precise set-up, maintenance and calibration, as well as expert operation to yield the best results. A spatial resolution target consists of manufactured defects of uniformed dimensions and geometries which can be measured to a high degree of accuracy. Implementing the use of a spatial resolution target, the dimensions of which are known and certified independently, would allow for rapid dimensional calibration of XCT systems for the purpose of object metrology. However, for a spatial resolution target to be practical it should be made of the same material as the intended specimen, or at least exhibit comparable X-ray attenuation. In this study, attempts have been made to manufacture spatial resolution targets using geopolymer, silica glass, and alumina rods, as well as 3D printed materials with varying degrees of success. The metakaolin was activated by an alkaline activator KOH to from a geopolymer paste that was moulded into a cylinder (Diameter approx. 25 mm). The solidified geopolymer cylinder as well as both the silica glass rod and alumina rod (Diameter approx. 25 mm) we cut to approximately 4 mm ± 0.5 mm height with additional end caps cut measuring 17.5 mm ± 2.5 mm height. All parts were then polished to a high finish and visually inspected for their suitability as spatial resolution targets.

The decommissioning of Korea Research Reactor Units 1 and 2 (KRR-1&2), the first research reactors in South Korea, began in 1997. Approximately 5,000 tons of waste will be generated when the contaminated buildings are demolished. Various types of radioactive waste are generated in large quantities during the operation and decommissioning of nuclear facilities, and in order to dispose of them in a disposal facility, it is necessary to physico-chemically characterize the radioactive waste. The need to transparently and clearly conduct and manage radioactive waste characterization methods and results in accordance with relevant laws, regulations, acceptance standards is emerging. For radioactive waste characterization information, all information must be provided to the disposal facility by measuring and testing the physical, chemical, and radiological characteristics and inputting related documents. At this time, field workers have the inconvenience of performing computerized work after manually inputting radioactive waste characterization information, and there is always a possibility that human errors may occur during manual input. Furthermore, when disposing of radioactive waste, the production of the documents necessary for disposal is also done manually, resulting in the aforementioned human error and very low production efficiency of numerous documents. In addition, as quality control is applied to the entire process from generation to treatment and disposal of radioactive waste, it is necessary to physically protect data and investigate data quality in order to manage the history information of radioactive waste produced in computerized work. In this study, we develop a system that can directly compute the radioactive waste characterization information at the field site where the test and measurement are performed, protect the stored radioactive waste characterization data, and provide a system that can secure reliability.

Most of the spent nuclear fuel generated by domestic nuclear power plants (NPPs) is temporarily stored in wet storage which is spent fuel pool (SFP) at each site. Currently, in case of Kori Unit 2, about 93.6% of spent nuclear fuel is stored in SFP. Without clear disposal policy determined for spent nuclear fuel, the storage capacity in each nuclear power plant is expected to reach saturation within 2030. Currently, the SFP stores not only spent fuel but also various non-fuel assembly (NFA). NFA apply to all device and structures except for fuel rods inserted in nuclear fuel assembly. The representative NFA is control element driving mechanism (CEDM), in-core instrument (ICI), burnable poison, and neutral resources. Although these components are irradiated in the reactor, they do not emit high-temperature heat and high radiation like nuclear fuel, so if they are classified as intermediate level waste (ILW) and low level waste (LLW) and moved outside the SFP, positive effects such as securing spent fuel storage space and delaying saturation points can be obtained. Therefore, this study analyzes the status of spent fuel and Non Fuel Assembly (NFA) storage in SFP of domestic nuclear power plants. In addition, this study predict the amount of spent fuel and NFA that occur in the future. For example, this study predicts the percentage of current and future ICIs and control rods in the SFP when stored in the spent fuel storage rack. In addition, the positive effects of moving NFA outside the SFP is analyzed. In addition, NFA withdrawn from SFP is classified as ILW & LLW according to the classification criteria, and the treatment, storage, and disposal methods of NFA will be considered. The study on the treatment, storage, and disposal methods of NFA is planned to be conducted by applying the existing KN-12 & KN-18 containers and ILW & LLW containers being developed for decommissioning waste.

It is important to make a strategy for clearance-level radioactive waste. Sampling and disposal plans should be drawn up with characteristics of target waste. In this paper, a target clearance-level radioactive waste is used in a laboratory for experiments with Cs-137 and Co-60, unsealed radioactive sources with gamma radiation isotopes. Therefore, it is enough to analyze with HPGe to check the contaminant level. The laboratory fume hood combined multiple materials, which means some are volume contamination and others are surface contamination. The wood, plastic, and drywall boards, which are absorbent volume contaminated parts and make up PVC pipes, base cabinet doors, backside baffles, etc., will be sampled with coring methods. The metals and glasses, which are unabsorbent, surface-contaminated parts, are sampled with smear methods. The work surface, baffles, exhaust plenum, and glass sash inside parts have a high possibility of being contaminated. The hood body, flame, base cabinet, PVC pipe (the rare end of the filter), and blower transition case have a low possibility of becoming contaminated. When we checked with HPGe, except for the work surface (which was below clearance level), other parts were less than MDA. The highest radionuclide concentration was in PVC pipe: Cs-137C 3.91E-02 (Bq/g), Co-60 4.54E- 03 (Bq/g). It is less than clearance level. Therefore, the waste was applied for the clearance level radioactive wastes and got permission from the regulatory body.

Level measurement of liquid radwaste is essential for inventory management of treatment system. Among various methods, level measurement based on differential pressure has many advantages. First, it is possible to measure the liquid level of the system regardless of liquid type. Second, as the instrument doesn’t need to be installed near the tank, there is no need to contact the tank when managing it. Therefore, workers’ radiation dose from the system can be decreased. Finally, although it depends on the accuracy, the price of the instrument is relatively low. With these advantages, in general, liquid radwaste level in a tank is measured using differential pressure in the treatment system. Not only the advantages described above, there are some disadvantages. As the liquid in the system is waste, it is not pure but has some suspended materials. These materials can be accumulated in tanks and pipes where the liquids move to come into direct contact with pneumatic pipes that are essential in differential pressure instruments. As a result, in case of a treatment using heat source, the accumulated materials may become sludge causing interference in pneumatic pipes. And this can change the pressure which also affects the level measured. In conclusion, in case of liquid storage tanks in which the situation cannot be checked, the proficiency of an operator becomes important.

Surface water temperature of a bay (from the south to the north) increases in spring and summer, but decreases in autumn and winter. Due to shallow water depth, freshwater outflow, and weak current, the water temperature in the central to northern part of the bay is greatly affected by the land coast and air temperature, with large fluctuations. Water temperature variations are large in the north-east coast of the bay, but small in the south-west coast. The difference between water temperature and air temperature is greater in winter and in the south-central part of the bay than that in the north to the eastern coast of the bay where sea dykes are located. As the bay goes from south to north, the range of water temperature fluctuation and the phase show increases. When fresh water is released from the sea dike, the surrounding water temperature decreases and then rises, or rises and then falls. The first mode of empirical orthogonal function (EOF) represents seasonal variation of water temperature. The second mode represents the variability of water temperature gradient in east-west and north-south directions of the bay. In the first mode, the maximum and the minimum are shown in autumn and summer, respectively, consistent with seasonal distribution of surface water temperature variance. In the second mode, phases of the coast of Seosan~Boryeong and the east coast of Anmyeon Island are opposite to each other, bordering the center of the deep bay. Periodic fluctuation of the first mode time coefficient dominates in the one-day and half-day cycle. Its daily fluctuation pattern is similar to air temperature variation. Sea conditions and topographical characteristics excluding air temperature are factors contributing to the variation of the second mode time coefficient.

Some of the metal waste generated from KEPCO NF is being disposed of in the form of ingots. An ingot is a metal that is melted once and then poured into a mold to harden, and it is characterized by a uniform distribution of radioactive material. When measuring the uranium radioactivity in metal ingot with HPGe detector, 185.7 keV of U-235 is used typically because most gamma rays emitted at U-235 are distributed in low-energy regions below 200 keV. To analyze radioactivity concentration of U-235 with HPGe detector more accurately, self-attenuation due to geometrical differences between the calibration source and the sample must be corrected. In this study, the MCNP code was used to simulate the HPGe gamma spectroscopy system, and various processes were performed to prove the correlation with the actual values. First an metal ingottype standard source was manufactured for efficiency calibration, and the GEB coefficient was derived using Origin program. And through the comparison of actual measurements and simulations, the thickness of the detector’s dead layers were defined in all directions of Ge crystal. Additionally instead of making an metal ingot-type standard source every time, we analyzed the measurement tendency between commercially available HPGe calibration source (Marinelli beaker type) and the sample (metal ingot type), and derived the correction factor for geometry differences. Lastly the correction factor was taken into consideration when obtaining the uranium radioactivity concentration in the metal ingot with HPGe gamma spectroscopy. In conclusion, the U-235 radioactivity in metal ingot was underestimated about 25% of content due to the self-attenuation. Therefore it is reasonable to reflect this correction factor in the calculation of U-235 radioactivity concentration.

The engineered barrier system (EBS) for deep geological disposal of high-level radioactive waste requires a buffer material that can prevent groundwater infiltration, protect the canister, dissipate decay heat effectively, and delay the transport of radioactive materials. To meet those stringent performance criteria, the buffer material is prepared as a compacted block with high-density using various press methods. However, crack and degradation induced by stress relaxation and moisture changes in the compacted bentonite blocks, which are manufactured according to the geometry of the disposal hole, can critically affect the performance of the buffer. Therefore, it is imperative to develop an adequate method for quality assessment of the compacted buffer block. Recently, several non-destructive testing methods, including elastic wave measurement technology, have been attempted to evaluate the quality and aging of various construction materials. In this study, we have evaluated the compressive wave velocity of compacted bentonite blocks via the ultrasonic velocity method (UVM) and free-free resonant column method (FFRC), and analyzed the relationship among compressive wave velocity, dry density, thermal conductivity, and strength parameter. We prepared compacted bentonite block specimens using the cold isostatic pressure (CIP) method under different water content and CIP pressure conditions. Based on multiple regression analysis, we suggest a prediction model for dry density in terms of manufacturing conditions. Additionally, we propose an empirical model to predict thermal conductivity and unconfined compressive strength based on compressive wave velocity. The database and suggested models in this study can contribute to the development of quality assessment and prediction techniques for compacted buffer blocks used in the construction of a disposal repository.

The most important thing in development of a process-based TSPA (Total System Performance Assessment) tool for large-scale disposal systems (like APro) is to use efficient numerical analysis methods for the large-scale problems. When analyzing the borehole in which the most diverse physical phenomena occur in connection with each other, the finest mesh in the system is applied to increase the analysis accuracy. Since thousands of such boreholes would be placed in the future disposal system, the numerical analysis for the system becomes significantly slower, or even impossible due to the memory problem in cases. In this study, we propose a tractable approach, so called global-local iterative analysis method, to solve the large-scale process-based TSPA problem numerically. The global-local iterative analysis method goes through the following process: 1) By applying a coarse mesh to the borehole area the size of the problem of global domain (entire disposal system) is reduced and the numerical analysis is performed for the global domain. 2) Solutions in previous step are used as a boundary condition of the problem of local domain (a unit space containing one borehole and little part of rock), the fine mesh is applied to the borehole area, and the numerical analysis is performed for each local domain. 3) Solutions in previous step are used as boundary conditions of boreholes in the problem of global domain and the numerical analysis is performed for the global domain. 4) steps 2) and 3) are repeated. The solution derived by the global-local iterative analysis method is expected to be closer to the solution derived by the numerical analysis of the global problem applying the fine mesh to boreholes. In addition, since local problems become independent problems the parallel computing can be introduced to increase calculation efficiency. This study analyzes the numerical error of the globallocal iterative analysis method and evaluates the number of iterations in which the solution satisfies the convergence criteria. And increasing computational efficiency from the parallel computing using HPC system is also analyzed.

To conduct numerical simulation of a disposal repository of the spent nuclear fuel, it is necessary to numerically simulate the entire domain, which is composed on numerous finite elements, for at least several tens of thousands of years. This approach presents a significant computational challenge, as obtaining solutions through the numerical simulation for entire domain is not a straightforward task. To overcome this challenge, this study presents the process of producing the training data set required for developing the machine learning based hybrid solver. The hybrid solver is designed to correct results of the numerical simulation composed of coarse elements to the finer elements which derive more accurate and precise results. When the machine learning based hybrid solver is used, it is expected to have a computational efficiency more than 10 times higher than the numerical simulation composed of fine elements with similar accuracy. This study aims to investigate the usefulness of generating the training data set required for the development of the hybrid solver for disposal repository. The development of the hybrid solver will provide a more efficient and effective approach for analyzing disposal repository, which will be of great importance for ensuring the safe and effective disposal of the spent nuclear fuel.

Since spent nuclear fuel (SNF) should be isolated from the human life zone for at least 106 years, deep geological disposal (DGD) is considered a strong candidate for SNF management in many countries. Therefore, a disposal canister should be nearly immune to corrosion in such a long-term storage environment. Even though copper has a low corrosion rate of a few millimeters per million years in geological environments, the corrosion resistance of the copper welds must be preferentially validated, which inevitably occurs during the sealing of the disposal canister after the SNF is loaded. This is because the weld zone is a discontinuous area of microstructure, which can accelerate uniform and localized corrosion. In this study, the microstructural characteristics of copper welds in different welding conditions such as friction stir welding, electron beam welding, cold spray, were analyzed, focusing on the formation of microstructure, which affects resistance to corrosion. In addition, the microstructure and corrosion properties of the copper weld zone manufactured by recent wire-based additive manufacturing (AM) technology were experimentally evaluated. From this preliminary test result, it was found that the corrosion characteristics of the welds produced by the AM process using wire are comparable to those of the conventional forged copper plate.

A methodology is under development to reconstruct and predict the long-term evolution of the natural barrier comprising the site of radioactive waste disposal. The natural barrier must protect the human zone from radionuclides for a long time. So for this, we need to be able to restore the evolution of the bedrock constituting the natural barrier from the past to the present and to predict from the present to the future. A methodology is being studied using surface outcrop, tunnel face of KURT (KAERI Underground Research Tunnel), and drill core at KAERI (Korea Atomic Energy Research Institute). Among them, drill core is an essential material for identifying deep geological properties, which could not be confirmed near the surface when considering the geological condition of the repository in the deep part. In this study, we selected several qualitative and quantitative analyses to construct a deep lithological model from the disposal perspective. These were applied to drill core samples around the KURT. There are the dikes presumed the Cretaceous were intruded by Jurassic granitoids in the study area. Analyzing trace elements of each rock type in the study area classified through geochemical characteristics and microstructure in previous studies made it possible to obtain qualitative information on the petrogenetic process. In addition, synthesizing the quantitative numerical age allows for grasping the evolution of bedrock, including intrusion and cutting relationships. LAICPMS was used for determining the age of zircons in plutonic rocks. The highly reliable 40Ar-39Ar method was selected for volcanic rocks because it can correct the loss of Ar gas and obtain the values of two types of Ar isotopes in a single sample. As a result, it was possible to infer the formation environment of rocks through anomalies in specific trace element content. And according to the numerical ages, it was possible to support the known separated rock type found in previous studies or to present a quantitative precedence relation for unclassified rocks. These methods could be applied to reconstruct the long-term evolution of bedrock within natural barriers.

South Korea has been storing UNF in spent fuel pool dry storage facility within Nuclear Power Plants. The dry storage facility of used nuclear fuel (UNF) is essential to sustain safety and sustain stable operation of a nuclear power plant. Most abroad countries have attempted to develop a variety of dry storage facility for used nuclear fuel in order to retain the safe restoration. Many studies have been conducting to safety evaluation for the dry storage facility. However, there is not a ventilation evaluation in the wake of fire event that could influence of the thermal effect on the dry storage facility, even though it will likely to occur fire events such as wildfire, air craft crash. In practice, it happened to catastrophic disaster due to the wild fire adjacent to ul-jin mountain. Also, it happened to fire accident near to the Japonia NPP in Ukraine territory caused of military air plane missile. It has not mostly been studied on the ventilation evaluation considered to thermal safety in the dry storage facility excepted for some researches. It could need the mechanical ventilation systems such as HVAC system in the dry storage system, so that thermal effect can be reduced. In this study, we conducted to the ventilation control modelling by using fire modelling tool (Fire Dynamic Simulator v.6.7). The ventilation scenarios made up for 3 case that can compare flowrate variation with ventilation control. As a result of modelling, there is no differentiation between ventilation control using performance curve with not using performance curve even though the pressure fluctuation would be increased, compared with the case of considering performance curve. Second, it evaluated that the mode for fraction control would occur to pressure rise in the state of controlling the ventilation system flowrate. However, sensitivity of flowrate control was more decreased below less than 5 seconds. Third, in the case of on/off control system revealed more higher resolution than other cases caused by flowrate variation. These results could be considered as the design guidelines for the development dry storage facility to improve the thermal performance that can reduce thermal risk. Furthermore, the study results would expect HVAC system installed in dry storage to help automatic ventilation control relevant to dry storage safety increased.

Korean MMTT project has been launched in order to clarify the vibration and shock loads under normal condition and transportation (NCT) in Korean geological and transportation conditions and to evaluate the integrity of SNF under such a transportation load. To evaluate the integrity of the SNF during normal land and sea transport tests, a representative SNF that represents the entirety of the different types of SNFs stored in the spent fuel pool of the power plant should be selected. And, it is necessary to make the test assembly to have a statically and dynamically similar behavior with the actual SNF. Therefore, in this project, we selected two types of fuel assembly that are expected to exhibit relatively conservative behavior under NCT, and these assemblies are being fabricated into surrogate test assemblies to have a similar characteristic as actual SNF based on the accumulated data from the poolside examination and the hot cell test so far. Tests were conducted for NCT conditions. In addition, a fatigue test was performed to integrity of the nuclear fuel rods under NCT conditions. Nuclear fuel assemblies are transported while being laid inside the cask under NCT, and are exposed to external shocks and vibrations. At this time, the fuel rod between the grid and grid is exposed to bending motion by this external force. For this simulation, a fixture was developed and used for static bending tests and bending fatigue tests. To simulate spent nuclear fuel rod specimens, hydrogen reorientation Zry-4 cladding was used and simulated pellets made of stainless steel were applied. And also, it was bonded using epoxy to give bonding conditions between the inside and the pellet. As a result of the test, cracks occurred due to the concentrated load between the pellets, resulting in damage to the fuel rod. The fatigue results showed a similar trend compared to the results performed by ORNL, and the lower bound fatigue curve presented by NUREG-2224 was also satisfactory.

Spent Fuel Pool Island (SFPI) is a spent nuclear fuel storage pool that operates independently of existing nuclear facilities to safely manage SNF and minimize maintenance costs during the nuclear decommissioning process. Since the radiation controlled area can be dismantled before transporting SNF to a dry storage facility, the overall decommissioning period can be shortened, and the risk of occupational exposure during dismantling is reduced. In the US, various nuclear power plants have introduced SFPI for this reason. In this paper, to analyze the economic feasibility of application of SFPI to nuclear power plants to be decommissioned, several scenarios are established in consideration of the decommissioning plan and schedule, SFPI and dry storage facility application schedule. Cost and benefit list (SFPI application cost, SNF management cost, SNF dry storage cask cost, etc.) for each alternative were derived, and economic analysis was conducted by applying the Net Present Value (NPV). As a result of the analysis, it is found that the application of SFPI during decommissioning is economically effective as the NPV showed a positive number even when uncertainty was taken into account.