This study was conducted to develop a heat interception permeability aggregate pavement material that resists increase of air temperature and has permeability by decreasing pavement temperature of city in summer. For this study, a heat interception polymer binder mixed with heat interception material and polyurethane binder. And the study made heat interception permeability aggregate pavement material by mixing heat interception polymer binder. Using the materials, the study conducted flexural strength test and temperature reduction effect experiment. As the result, flexural strength was 5.43MPa average and the temperature reduction effect was effective up to maximum 16 degrees Celsius compared to current asphalt concrete.

일반적으로 지진취약도를 평가할 때 사용되는 해석방법 중 하나인 역량스펙트럼 방법은 증분동적해석에 비해 해석의 정확성이 떨어지는 제한점이 있다. 본 연구에서는 증분동적해석이 가장 정확도가 높은 해석기법이라는 점에 착안하여 증분동적해석을 이용한 지진취약도 곡선의 도출과정을 제안하였다. 타당성 비교를 위하여 역량스펙트럼 방법과 제안된 방법으로 도출한 취약도 곡선을 비교하여 두 해석기법에 의한 지진취약도 곡선의 경향을 분석하였다. 그 결과 Slight damage와 Moderate damage의 경우 두 해석방법이 유사한 곡선 경향을 보이나 Extensive damage와 Complete damage의 경우에는 IDA방법에 의한 곡선이 더 가파른 경향을 보였다. 이는 구조물의 거동을 이상화하여 극한점 이후 구조물의 저항 강도가 떨어지지 않는다고 가정하는 역량스펙트럼 방법의 영향을 받는 것으로 사료된다.

목적: 안경광학과 교과과정에 대한 만족도를 조사하여 효율적인 교과과정 개발에 기초자료로 활용하고자 하였다. 방법: 경기지역 안경광학과 재학생 183명과 서울, 경인지역 산업체 재직 안경사 123명을 대상으로 교과과정에 대한 만족도 설문조사를 실시하고 통계분석을 실시하였다. 결과: 안경광학과 교과과정을 5개 분야로 구분하여 5점 척도로 만족도를 조사한 결과, 두 집단의 교과과정 만족도는 유사한 경향을 보여주었는데(재학생: 16.44±2.66, 산업체: 16.47±3.38) 분야별로는 이론교육의 만족도가 가장 높게 나타났으며(재학생: 3.87±0.74, 산업체: 3.82±0.68) 외국어교육과 인성교육에 대한 만족도가 낮게 나타났다. 재학생의 경우에 이론교육(p

This study investigated the biomass content of fluff type SRF(Solid refuse fuel) operated in B city according to the physical composition. As a result of analyzing the physical composition of SRF, it was investigated that papers 25.2%, fiber 15.1%, vinyl‧plastics 42.6%, woods 9.4%, rubbers 1.5%, diapers 3.2% and incombustibles 3.0%. The average of ash and combustible content of SRF was 10.5% and 89.5%, and the higher the proportion of paper and wood, the lower proportion of ash. In addition, the biomass of SRF is 24.9%~58.0%, with an average of 42.6%.

This study explored measures to reduce noise applicable to Gimhae international airport centering on densely packed housing areas. Especially, as for measures to relieve noise damage on the densely packed housing areas in Gimhae-si, the noise reduction effect is expected to be doubled if the west runway (36L/18R) is used as the preferred runway for the 36 direction takeoff, as well as if the flight bypasses the densely packed housing areas by means of sophisticated navigation using the area navigation (RNAV) procedure based on performance-based navigation (PBN). Takeoff toward the south connects the flight path to the South Sea which has comparatively low noise impact, relieving noise damage on the densely packed housing areas (apartment complexes in Naeoe-dong of Gimhae-si, etc.) near the northern end of the runway. The operation of the runway displaced threshold is currently being implemented on the west runway (36L/18R) of Gimhae international airport. It has been found that swing landing in spring and summer when the wind blows from the south has a noise reduction effect on the noise sensitive areas at the side and end of the west runway (Gangdong-dong and Jukdong-dong of Gangseo-gu and Buram-dong of Gimhae-si, etc.).

In this study, we evaluated the effect of the type of sewage sludge (digested, non digested) on drying efficiency according to the polymer injection rate. The drying characteristics were shown using a near-infrared ray (NIR) and a microwave. As a result of the drying characteristics with NIR at a polymer dose ratio of 8%, the heating up period is up to 6 minutes after the start of the drying experiment. Afterwards, the constant rate drying period of the digested sludge (A, C and G sites) was 6 minute → 18 minute, showing a rapid decrease in moisture. On the other hand, non digested sludge (B, D, E, F, H, I, J and K sites) showed gradual drying characteristics compared to digested sludge until complete drying (10%). As the polymer dose ratio of 10% and 12%, the heating up period for digested sludge is up to 6 minute after the start of the experiment. Afterwards, the constant rate drying period of the digested sludge was 6 minute → 20 minute, showing a rapid decrease in moisture. On the other hand, the heating up period of non digested sludge was up to 10 minute after the start of the experiment, and the constant rate drying period was 10 minute → 22 minute, which was shorter than digested sludge. As a result of the drying characteristics with microwave at a polymer dose ratio of 8%, 10% and 12%, the constant rate drying period the digested sludge was 4 minute → 20~22 minute, showing a rapid decrease in moisture. On the other hand, non digested sludge of the constant rate drying period was 4 minute → 22~30 minute, which was longer than digested sludge.

This study executed evaluation of drying characteristics based on the polymer injection rate (8%, 10% and 12%) and the drying method[NIF(near-infrared ray). According to this study analyzed VS, VS/TS, and calorific value compared with ‘the auxiliary fuel standard of the thermoelectric power plant and the combined heat & power plant’. The results are as follows. In the case of NIR, the VS was slightly changed at the early stage of the material preheating period and the constant drying rate period with low moisture evaporation. But VS reduction was shown higher as moisture was dried. In the case of non-digested sludge with high VS content, the VS reduction rate by drying was shown lower than that of digested sludge. As the flocculant injection rate increased, the VS loss due th drying was found to be small. Also, the higher the flocculant injection rate was the longer the drying time. Especially, in the case of the NIR drying equipment, as the moisture content of sewage sludge decreased(moisture content 20∼40%), the loss of net VS also showed a tendency to increase sharply. It is shown that the high calorific value according to the drying time of the non-digested sludge was changed from 590 ㎉/㎏ to 3,005 ㎉/㎏ and from 539 ㎉/㎏ to 2,796 ㎉/㎏.

The purposes of this study were to evaluate the removal characteristics of COD, Ni, and P and to derive appropriate operating conditions for the plating wastewater according to NaOCl reaction time and pH operating conditions in the BPC unit process during the plating wastewater treatment process. As a results of evaluating the removal characteristics for raw wastewater by each BPC unit process, the removal efficiencies of COD, Ni and P in BPC 1-1 unit process were 72.8%, 99.1%, and 100.0%. Therefore, the proper reaction time of NaOCl was derived as 21.1 minutes. In order to maintain the +800 mV ORP and the reaction time of 20 minutes, the temporary injection and continuous injection of NaOCl in the BPC unit process were 13.7 mL and 18.7 mL, respectively. It was found that the temporary injection method of NaOCl reduced the chemical cost by 36.5% compared to the continuous injection method. Also, Ni showed the highest removal efficiency of 97.8% at pH 10.5. On the other hand, P showed a removal efficiency of 57.4% at pH 10.0.

In this research, heavy metals and T-P removal characteristics of plated wastewater are derived using BPC(Break Point Chlorination) process. AA sedimentation pond outflow(Influence) was evaluated for the removal efficiency of heavy metal(Ni) and T-P at a reaction time of 25 minutes by NaOCl input volume(9, 11, 13 and 15 mL). In the case, the higher the NaOCl input volumes, the higher the ORP values were maintained and the higher the removal efficiency tended to be. On the other hand, T-P was judged to have a low relationship between the ORP value and the removal efficiency. In addition, the efficiency of removal heavy metals and T-P in the plated wastewater by injecting 10 mL, 15 mL, 20 mL and 25 mL NaOCl, increased as the amount of NaOCl injected increased, the amount of NaOH input for pH increased. It was found that suspended solid in effluence also increased. It was also observed that the color of the plating wastewater changed from yellowish green to green to charcoal gray to black as the amount of NaOCl injected increased. Treatment characteristics of the reaction time, the longer the reaction time with the substance to be treated after the input of NaOCl, the more the heavy metal removal efficiency tended to increase. Through XRF analysis of the sludge, the constituents in the sludge such as NaCNO, CNCl, Na3PO4, CrO4, 2Na2CrO4 and 2NaNO3 will be analyzed in detail, and the mechanisms of the reaction between the plated wastewater and the complex compound will be elucidated.

Using the waste(sand wastr and boiler ash) in fluidized bed inciverator, lightweight aggregate concrete was produced and a recycling plan was prepated. The first, the result of the leaching test shows that the waste fluid sand and boiler ash did not exceed the effluent standard. This indicates that there is no harmful effect for recycling. The second, in the lightweight aggregate test using waste fluid sand and boiler ash, the sample that combined cement, waste fluid sand, and sand showed the highest compressive strength, and the mix proportion was 10: 7: 3. Lightweight aggregate concrete that combined cement, waste fluid sand, boiler ash, and sand had a low compressive strength by and large. The third, the same results were identified in the relation between the content of SiO2 and that of Na2O. As the SiO2 content is lowered, the overall viscosity and plasticity of the concrete also decrease, which is not a good condition to form concrete. As for Na2O, as the content increases, the viscosity of the sample and the viscosity of the cement are remarkably lowered, and the strength of the finished concrete is lowered. Therefore, it was concluded that the higher the content of SiO2 and the lower the content of Na2O, the more suitable it is to mix with cement to produce concrete. Fourth, from the fluidized bed incinerator currently operated by company A in city B, a total of 14,188 tons/year were discharged as of 2016, including 8,355 tons/year of bottom ash (including waste fluid sand) and 5,853 tons/year of boiler ash. The cost for landfill bottom ash and boiler ash discharged is 51,000 won/ton, and the total annual landfill cost is 723,588,000 won/ year. Assuming that the landfill tax to be applied from the year 2018 is about 10,000 won/ton, and if there is no reduction in waste disposal charge, an additional landfill tax of 141,880,000 won/year will be imposed. Consequently, the sum total of the annual landfill cost will be 865,468,000 won/year. Therefore, if the entire amount is used for recycling, the annual savings of about 8.7 billion won can be expected.

The Korean environmental impact assessment(EIA) system, and explored ways to improve it as a more efficient and viable institution relevant to the demand of our time and conditions in study. The first problem this study identified is found in the fact that the party to write up the assessment report is itself the business operator or the one who is planning to work out the business plan. This structure translates into placing an order with an agent for EIA report. The reporting job may br subcontracted to the agent at a cost far below the rate specified in the ‘Standard for Estimate of Agency Fee for Environmental Impact Assessment.’ This practice also causes the vicious circle of producing a report that is written to justify the project or business in question or it leads to rough-and ready and poor documentation to minimize the time required. Second, in order to achieve the goal of the plan or business, which is the target of EIA, the local residents tend to ve regarded as an obstacle. This means elimination of the local people from participating in the EIA or their opinion being frequently ignored. This is the seed of distrust and hostility that sometimes provoke disagreements or fierce conflicts. The first proposal to improve these problem is to improve the factors that cause poor documentation of the assessment report as well as improve the understanding of the EIA system. This study proposes the following measures for improvement. The agency cost for EIA should be paid by the business operator or a third party that can ensure faithful implementation of the payment. A system should be established to verify transparent estimation of the agency cost. In order to enhance the professional quality of EIA agents, there should be implementation of qualification test for industrial engineer of related engineers in addition to the current EIA Qualification Test. The second proposal for improvement is to improve the citizen participation process by instituting a legal framework to make clear the purpose of the briefing session for local residents, which is held as a procedure of EIA, and to ensure more positive publicity during the stage of listening to the opinion of the local community. For a smooth and rational communication process, a moderator and a communicator of opinion, as is the case in a public hearing, could be instituted to clearly get the purpose of the briefing session across to the residents and to help to carry out the explanation and Q & A sessions according to the categories of the opinion of the residents. At present, the notification of the public inspection of the draft of the assessment report and briefing session for the residents is made on the newspaper and internet network. But some people have difficulty with access to this method of announcement. A higher participation rate could be secured if a legal provision is added to specify putting up placards in specific places such as the entrance to the place for the briefing session for residents or the building of administrative agencies of the area concerned.

우리나라에서 폐기물을 처리하는 방법에는 크게 매립, 소각, 재활용이 있으며 일반적으로 폐기물을 수거하여 재활용 할 수 있는 부분을 제외한 나머지는 소각한 뒤 매립을 하는 방식을 택하고 있다. 매립은 계속적인 매립지 확보에 어려움을 겪고 있으며 폐기물의 배출량이 갈수록 증가됨에 따라 예상되는 매립지의 기대수명이 점점 감축되고 있다. 이러한 상황에서 우리나라에서는 폐기물을 짧은 시간 안에 매우 안정적으로 처리할 수 있는 소각기술로 시야를 넓혀야 한다. 소각은 대부분 재활용할 수 있는 폐열 및 고형화연료를 확보할 수 있을뿐더러 매립지의 수명도 효과적으로 늘릴 수 있다. 또한 소각이 완료된 후의 소각재는 수분까지도 거의 제거된 상태이기 때문에 바로 매립이 가능한 정도에 이르렀다. 환경부에서 발행한 ‘전국 폐기물 발생 및 처리 현황(2015년도 수정본)에 따르면 소각과정에서 발생된 연소재의 일일배출량은 점점 증가하는 추세이다. 따라서, 소각재를 매립하는 방법 외에 재활용할 수 있는 방안을 모색하여 매립지의 수명연장은 물론 효율적인 재활용자원으로 사용할 수 있게 만드는 것이 필요하다. 그러나 소각재는 현행 폐기물 관리법상 중금속 농도가 비교적 낮기 때문에 일반폐기물로 관리되고 있었으나 유해성 논란이 끊이질 않고 있다. 따라서, 소각재에 들어있는 유해중금속의 농도를 효과적으로 처리하여 낮추면 다른 분야에서 즉각 활용할 수 있는 좋은 재료로 사용할 수 있을 것이다. 본 연구에서는 소각재의 처리 실태를 알아보고 재활용되고 있는 방법들을 검토, 비교하고 현재 유동상식 소각로에서 배출되는 폐유동사의 재생골재로의 재활용 가능성에 대해 알아보았다. 추가적으로 유동상식 소각로에서 배출되는 보일러재와의 배합 가능성, 그리고 성분분석을 이용한 함유성분의 함량과 재활용 목표의 관계도 연구하였다. 이는 기존에 활용되고 있는 재활용 방법과 새롭게 이용할 수 있는 방법에서 원재료로 사용되고 있는 것들을 대체할 수 있는가에 대한 것이다. 기존에 사용되고 있는 원재료만큼의 효율이 나온다면 원가절감은 물론 폐기물 재활용, 나아가서는 자원재이용에 따른 환경문제 감소에 도움이 될 수 있을 것이라 판단된다.

This study carried out first a component survey on the domestic waste shipped into a waste disposal facility in B city, and then heavy metal analysis of each component according to the SRF standards. Based on this, this study explored the problems with domestic waste and measures to improve them. The results are as follows. The result of the survey of physical components show that paper accounted for the largest proportion with 20.5 %~59.9 %, metals (including batteries) among incombustibles accounted for 0.0~8.3 %, other inorganic substances, glass and ceramics accounted for 0.0~43.7 % and 0.0 %~19.6 % respectively. However, the proportion of coated viny and plastics, which have high lead and cadmium content, was rather high with 2.9 %~30.9 %. This suggests the possibility that actual concentration of lead and cadmium within SRF is likely to be higher. Among the 15 components contained in the waste brought into the waste disposal facility, 10 components (food waste, textiles, vinyl, plastics, wood, rubber and leather, paper, metals, electronic substrates, and nail polish) were analyzed according to assay samples (approximately 0.1 g and 0.3 g). The result of analysis shows that the amount of Cd and Pb detected in coated vinyl for 0.109 g of assay sample was 98.6 mg/kg and 20.6 mg/kg respectively; 117.0 mg/kg and 29.0 mg/kg respectively for 0.313 g of assay sample. This is high contents exceeding the Cd standard. As for wooden component, the amount of Pb was 480.0 mg/kg for 0.3 g of assay sample. This suggests that there always exists the possibility of exceeding the exposure level of heavy metals (Cd and Pb) in SRF as long as coated wood and vinyl·plastics with high contents of Pb and Cd are shipped into the waste disposal facility; and the local government and the residents need to work hard to improve the situation including development of the machine to sort electronic substrates and batteries for separate collection of the waste of coated vinyl and plastics within domestic waste.

Research was conducted on the characteristics of waste discharge in apartment houses with less than 200 households. Implementation of the meter-rate system of food waste for apartment houses was also investigated and an economic evaluation was carried out to reach the following conclusions. First, for the monthly characteristics of the overall amount of food waste in apartment houses with less than 200 households, December and January exhibited the maximum amount while February and March exhibited the minimum amount of discharge. The average amount of waste discharge per household was the lowest at 0.51 kg/day · household in apartment houses with 20 to 50 households, followed by 0.80 kg/day · household in apartment houses with less than 20 households and in apartment houses with 50 to 100 households. Apartment houses with 100 to less than 200 households had 0.71 kg/day · household of average waste discharge. The results showed that the amount of food waste discharge is dependent upon the economic conditions or environment of the regions concerned rather than upon the number of households. Second, two meter-rate systems of food waste were compared: the RFID system and the Chip system. When the comparison was made under the same conditions for the number of households in apartment houses in which meter-rate system was being implemented, the average reduction rate in the Chip system was 21.1% and that in the RFID system was 57.1%. A comparison of apartment houses under the meter-rate system and of apartment houses with less than 200 households with apartment houses with less than 20 households, 20 to 50 households, 50 to 100 households, and 100 to less than 200 households showed that the average reduction rates of the Chip system and the RFID system was 35.3% and 61.9%, respectively. Last, a comparison of the results of the field study and the rate of food waste reduction in regions where the meter-rate system was being implemented showed that the average reduction was 35.3% for the Chip system and 61.9% for the RFID system, with a difference in reduction of about 35.5%. In the case that the RFID system is adopted, the disposal cost of about 62.7 billion won per year would be reduced by about 19.4 billion won, which leads to a prediction of a reduction in disposal cost to about 43.3 billion won per year.

The objective of this research is to evaluate optimal conditions of permeability and selectivity on the polysulfone membrane for efficiency of separation of CH4 by checking four factors which are temperature, pressure, gas compositions and gas flow rates. When higher pressure was applied at the input, lower efficiency of recovery of CH4 and higher efficiency of separation of CH4 were shown. It has the tendency to show lower efficiency of recovery of CH4 and higher efficiency of separation of CH4 at the output as higher temperature at input. The lower flow rates make higher efficiency of recovery of CH4 and lower efficiency of separation of CH4. Finally, over 90% efficiency for CH4 separation and recovery conditions are temperature (-5℃), pressure (8 bar), gas composition rate (6:4) (CH4:CO2) and gas flow rate (5 ℓ/min). These conditions make higher separation and recovery efficiency such as 90.1% and 92.1%, respectively.

The objectives of this study were to investigate the seasonal characteristics of metallic and ion elements of PM10(Particulate matter with aerodynamic diameter ≤10 ㎛) and the effects of vessels exhaust emission from ships harboring in Busan City. The PM10 samples were collected from January 2010 to October 2010 at Dongsam-dong(coastal area), in Busan City. The particulate matters were analyzed for major water soluble ionic components and metals. The ranges of the PM10 mass concentrations were from 29.8 ㎍/㎥ to 47.0 ㎍/㎥ in Dongsam-dong. The PM10 mass concentrations in Dongsam-dong are very similar to Gwangbok-dong during same sampling periods. These results were understood by the effects of the shipping source emitted from ships anchoraging and running. The concentrations of water-soluble ions and metals in the PM10 had a level of as high as the order of SO4 2- >NO3 - >Cl - and NH4 + >Na + >Ca 2+ >K + >Mg 2+ , respectively. The correlation coefficients(R 2 ) for SO4 2- /PM10 and NH4 + /PM10 of were 0.7446 and 0.7784, respectively, and it showed the high correlation with each other.

In order to know the effect of autoclaving on the heavy metal removal using chitosan, lead removal capacities and removal rates by various chitosans in aqueous solution were compared according to the various autoclaving time. The lead removal efficiencies and removal rates by the autoclaved chitosan were found to be on the order of 15 min(98%) 〉10 min(95%) 〉30 min(83%) 〉5 min(53%) 〉60 min(47%) 〉0 min(22%) chitosan. The molecular weight of chitosan was decreased by the increase of autoclaving time. Therefore, the heavy metal removal capacity was not well correlated to the molecular weight. Langmuir isotherm was well fitted to experimental results of equilibrium adsorption on chitosan. In order to examine the process of lead removal by the autoclaved chitosan, TEMs, SEMs and FT-IR analyses were used. The surface of autoclaved chitosan was much more porous and the lead removal was mainly occurred on the surface of chitosan. The structure of autoclaved chitosan was same as that of controlled chitosan.