Y-type barium ferrite was prepared by the glass-ceramic method. Glasses with composition of were prepared, and the precipitation behavior of Y-type ferrite from the glass matrix was investigated by heating glass specimens at various temperature. which is a precursor of M-type ferrite was precipitated at about 813 K and an unknown compound, phase X, was precipitated at about 850 K. M-type ferrite and Y-type ferrite started to form at about 923 K and 1103 K, respectively. The formation of Y-type ferrite was int erpreted as the result of the reaction of M-type ferrite with a melt of phase X.

Y-type barium ferrite ( Me=Zn, Co, Cu) expected as an electromagnetic wave absorber were prepared by the glass-ceramic method. The glasses with composition of were prepared. Single-phase powders of Y type barium ferrite were obtained with the composition . The shape of Y-type crystals depended strongly on the heating temperature and changed from a plate-like hexagon to a complex polyhedron with increasing heating temperature. Correlation was recognized between saturation magnetization and crystal shape. Electromagnetic wave absorption characteristics was affected by the saturation magnetization and crystal shape.

TZM alloy having elongated coarse-grain structure was developed by three-step internal nitriding treatment at 1423 to 1873 K in and subsequent recrystallization treatment at 2173 K in vacuum. Some specimens were subjected to re-nitriding treatment at 1873 K for 16 h. After the recrystallization treatment, aspect ratio (L/W) of grains for rolling direction was about 50 at the maximum. Yield stress obtained at 1773 K after re-nitriding treatment was about 6 times as large as that of recrystallized specimen. Re-nitriding was very effective in the improvement in strength of TZM alloy having elongated coarse-grain structure.

In order to overcome the recrystallization embrittlement and irradiation embrittlement of Mo, which are major problems for its fusion applications, internally nitrided Mo alloys were prepared by a novel multi-step internal nitriding. Neutron irradiation was performed in the Japan Material Testing Reactor (JMTR). After irradiation, nitrided Mo alloys exhibited ower ductile-brittle transition temperature than irradiated TZM. These results suggested that multi-step internal nitriding was effective to the improvement in the embrittlement by irradiation. Transmission electron microscope observation revealed that TiN particles precipitated by nitriding acted as a sink for irradiation-induced defects.

For pure Molybdenum carburized in mixed gases of argon and carbon monoxide, microstructural observations were carried out. X-ray diffraction analysis for carburized specimens revealed that brittle - layer hardly formed in the case of low carbon monoxide concentration. Fracture strength of the specimen carburized at 1673 K for 16 h is about 550 MPa higher than that of the un-carburized specimen. SEM observation revealed that with increasing carburizing temperature, the region demonstrating a transgranular fracture mode progressed towards the center of specimen. This result means that the grain boundaries were strengthened by the grain boundary diffusion of carbon and the strength of grain boundaries exceeded that of grain itself.

Internally nitrided dilute W-Ti alloy specimens having a heavily deformed surface microstructure were prepared by a multi-step internal nitriding at 1573-2073 K. Primary nitriding below their recrystallization temperature induced a precipitation of ultrafine TiN particles. After secondary and tertiary nitriding, those precipitates grew into rod-like TiN with a length of 20-60 nm. The recrystallization temperature after nitriding was elevated above 2073 K. The yield strength at 1773 K obtained from nitrided W-0.5 mass% Ti alloy was about 5 times as large as that of the recrystallized specimen. DBTT of the nitrided alloys was about 373 K.

The coating of conductive polypyrrole (Ppy) on nonconductive ceramic substrates was performed by polymerization of pyrrole (Py) in an aqueous solution. The Ppy film was characterized by scanning electron microscopy and conductivity measurements. Electrophoretic deposition of bimodal alumina suspension prepared with a phosphate ester was performed using Ppy film as a cathode. Fabrication of alumina ceramics with irregular shapes or complicated patterns were also attempted by sintering the deposits together with the Ppy coated substrates in air.

The mechanical properties of ceramics materials can be tailored by designing their microstructures. We have reported that development of texture can be controlled by slip casting in a strong magnetic field followed by heating even for diamagnetic ceramics such as alumina. A strong magnetic field of 12T was applied to the suspension indcuding alumina powder to rotate each particle during slip casting. The sintering was conducted at the desired temperature in air without a magnetic field. C-axis of alumina was parallel to the magnetic field. Bending strength of textured alumina depended on the direction of oriented microstructure.

This work will report a highly textured β-Si3N4 ceramic by aqueous slip casting in a magnetic field and subsequent pressureless sintering, Effects of the sintering aids, polymer dispersant, pH and stirring time on the stability of the Si3N4 slurries were studied. The textured β-Si3N4 with 97 % relative density could be obtained by slip casting in a magnetic field of 12 T and subsequent sintering at 1800 oC for 1 h. The textured microstructure is featured by the alignment of c-axis of β-Si3N4 crystals perpendicular to the magnetic field, and the Lotgering orientation factor, f, is determined to be 0.8.

The deformation behavior under three-point bend test was found to depend on the loading uniformity and the macrostructure for SiC reticulated porous ceramics (RPCs). However, this dependence of loading uniformity is alleviated by improved macrostructure with fewer flaws and clogged pores. Even, this dependence becomes less important as the struts become thicker and stronger. The bend result of RPCs with highly uniform macrostructure is in excellent agreement with the GA (Gibson and Ashby) model, but the one with un-uniform macrostructure deviates from the GA model, suggesting that the macrostructure plays an important role in deformation behavior of RPCs under bend.

Recently the Marangoni convention is supposed to be an important phenomenon that significantly affects the solidification. For understanding the Marangoni convection mechanism, visualizing the convention phenomenon of molten tin with ultrasonic has been conducted. This paper reports developing a tracer material of micro metal balloon that is used in the molten system. We have succeeded in coating the surface of Shirasu-ballons with nickel by plating process. The obtained metal balloon is spherical and some characterizations were conducted.

We have demonstrated that textured nanocomposites can be fabricated by slip casting followed by partial oxidation. reaction sintering of mixed suspensions of and SiC powders in a high magnetic field. The sintered density was changed by the degree of oxidation at 1200C and 1300C. The degree of orientation of alumina in the nanocomposite was examined on the basis of the X-ray diffraction patterns and scanning electron micrographs. It is confirmed that aluminaoriented nanocomposites were fabricated. The three-point bending strength at room temperature was observed for the nanocomposites.

We have demonstrated that textured nanocomposites can be fabricated by slip casting followed by partial oxidation - reaction sintering of mixed suspensions of and SiC powders in a high magnetic field. The sintered density was changed by the degree of oxidation at 1200C and 1300C. The degree of orientation of alumina in the nanocomposite was examined on the basis of the X-ray diffraction patterns and scanning electron micrographs. It is confirmed that alumina-oriented nanocomposites were fabricated. The three-point bending strength at room temperature was observed for the nanocomposites.

We demonstrate the methodology of engineering the multi-component ceramic nanopowder with precise morphology by nanoblast calcinations decomposition of preliminary engineered nanoreactors. Multiple explosions of just melted embedded into preliminary engineered nanoreactors break apart the agglomerates due to the highly energetic impacts of the blast waves. Also, the solid-solubility of one component into the other is enhanced by the extremely high local temperature generated during each nano-explosion in surrounding area. This methodology was applied for production of agglomeratefree nano-aggregates of with an average size of 42 nm and nanopowder with an average aggregate size of 83 nm.