ber reinforced polymer (FRP) reinforcing bars for concrete structure have been extensively investigated and a number of FRP bars are commercially available. However, major shortcoming of the existing FRP bars is low elastic modulus compared to conventional steel bars. Because of these reasons, FRP Hybrid Bar which have the concept of material hybridization(synthetic resins, deformed bar, glass fiber etc) for concrete structures have been developed. One of main features of this bar is corrosion resistance and this is important to confirm this anti-corrosion capacity of FRP Hybrid Bar. In this study, galvanic corrosion current behavior of 3 types of specimens, including two types of FRP Hybrid Bars and one conventional steel rebar, was investigated under the 0%, 1.5%, 3% and 6% salt water ratio condition. The result of this study can be used to evaluate the applicability of FRP Hybrid Bar to concrete structures.

The structural formation of inorganic nanoparticles dispersed in polymer matrices is a key technology for producing advanced nanocomposites with a unique combination of optical, electrical, and mechanical properties. Barium titanate (BaTiO3) nanoparticles are attractive for increasing the refractive index and dielectric constant of polymer nanocomposites. Current synthesis processes for BaTiO3 nanoparticles require expensive precursors or organic solvents, complicated steps, and long reaction times. In this study, we demonstrate a simple and continuous approach for synthesizing BaTiO3 nanoparticles based on a salt-assisted ultrasonic spray pyrolysis method. This process allows the synthesis of BaTiO3 nanoparticles with diameters of 20-50 nm and a highly crystalline tetragonal structure. The optical properties and photocatalytic activities of the nanoparticles show that they are suitable for use as fillers in various nanocomposites.

Salt, as food, is the most essential element for human survival due to its significant physiological functions. Here, we report the simultaneous detection of Pb and Cd in sea salt by square wave anodic stripping voltammetry (SWASV). Stripping voltammetric measurements were conducted using a manufactured rotating disk electrode system (MRDES). The detection limit was 3.6±0.18 μgL−1 for Pb and 3.9±0.37 μgL−1 Cd in NaCl solution. When the pH increased from 5.5 to 8.5, the peak currents of Pb and Cd decreased. At a pH of 8.3, the ratio of the current drop compared with that at a pH of 5.5 was 0.6 for Pb and 0.73 for Cd. The concentrations corrected by the current drop are in agreement with the concentrations obtained with ICP (inductively coupled plasma). This system demonstrates the reliable detection of heavy metals in aqueous media and, at a high Na + concentration, the successful application for the determination of Pb and Cd in sea salts.

Salt, as food, is the most essential element for human survival due to its significant physiological functions. Here, we report the simultaneous detection of Pb and Cd in sea salt by square wave anodic stripping voltammetry (SWASV). Stripping voltammetric measurements were conducted using a manufactured rotating disk electrode system (MRDES). The detection limit was 3.6±0.18 µgL− 1 for Pb and 3.9±0.37 µgL− 1 Cd in NaCl solution. When the pH increased from 5.5 to 8.5, the peak currents of Pb and Cd decreased. At a pH of 8.3, the ratio of the current drop compared with that at a pH of 5.5 was 0.6 for Pb and 0.73 for Cd. The concentrations corrected by the current drop are in agreement with the concentrations obtained with ICP (inductively coupled plasma). This system demonstrates the reliable detection of heavy metals in aqueous media and, at a high Na + concentration, the successful application for the determination of Pb and Cd in sea salts.

Densities of molten salt mixtures of eutectic LiCl-KCl with UCl3, CeCl3, or LaCl3 at various concentrations (up to 13 wt%) were measured using a liquid surface displacement probe. Linear relationships between the mixture density and the concentration of the added salt were observed. For LaCl3 and CeCl3, the measured densities were significantly higher than those previously reported from Archimedes’ method. In the case of LiCl-KCl-UCl3, the data fit the ideal mixture density model very well. For the other salts, the measured densities exceeded the ideal model prediction by about 2%.

in vitro studies on salt torerance was carried out with Salix gracilistyla. Shoot growth of plants treated with NaCl showed statistically significances among different levels of concentration(0~200 mM) on 1/2MS medium. Plant growth was not grown at in higher concentration than 75 mM and plants were dead over 150 mM Nacl Browned leaf was observed from 14 days at higher concentration than then 75 mM NaCl, and chlorophyll content was dramatically decreased. Main roots and rootlet in same concentrates(75 mM) or high NaCl treatment were changed the color to black. The proline and sugar contents were dramatically increased in the higher than 75 mM NaCl treatments after 14 - 15 days. To determine NaCl and minerals in salt stressed plants, leaf, stem and root of in vitro plant were subjected to ICP analysis. Na content was increased with culture days in all three parts. These results suggest that S. gracilistyla can be used vegetative restoration in coastal wetlands reclaimed.

Inorganic phosphors based on ZrO2:Eu3+ nanoparticles were synthesized by a salt-assisted ultrasonic spray pyrolysis process that is suitable for industrially-scalable production because of its continuous nature and because it does not require expensive precursors, long reaction time, physical templates or surfactant. This facile process results in the formation of tiny, highly crystalline spherical nanoparticles without hard agglomeration. The powder X-ray diffraction patterns of the ZrO2:Eu3+ (1-20 mol%) confirmed the body centered tetragonal phase. The average particle size, estimated from the Scherrer equation and from TEM images, was found to be approximately 11 nm. Photoluminescence (PL) emission was recorded under 266 nm excitation and shows an intense emission peak at 607 nm, along with other emission peaks at 580, 592 and 632 nm which are indicated in red.

The straight nanopores in cellulose acetate (CA) polymers for battery gel separators were generated by utilizing both Ni(NO3)2·6H2O and water pressure. When polymer film was exposed to water pressure, the continuous nanopores were generated after complexing with Ni(NO3)2·6H2O. These results could be explained by that polymer chains were weakened because of the plasticization effect of the Ni(NO3)2·6H2O incorporated into the CA. The well controlled CA membrane after water pressure treatment enabled fabrication of highly reliable cell by utilizing 2032-type coin cell structure. The resulting cell performance exhibited both the effect of the physical morphology of CA separator and the chemical interaction of electrolyte with CA polymer which facilitates the Li-ion in the cell.

Differences in sugar and salt penetrarion rates of radish depending on size and concentration of solution were examined. 2x2x2 and 4x4x4 cm cube-shaped radish examined in different pickling condition (salt 2, 4, 6, 8% and sugar 5, 10, 15, 20% brix). After 12hr storage, Salt penetration rate of radish cut into 2x2x2 cm was faster than that of 4x4x4 cm in all salt solution. Size dependent sugar penetration showed same tendency with size dependent salt penetration. Also, increase in salt and sugar concentration led to increase in salt and sugar permeation rate.

양이온 계면활성제는 살균력을 가지고 있으며 이를 개발하기 위한 연구는 다양한 산업분야에 서 계속 진행되고 있다. 단순히 우수한 성능을 가질 뿐만 아니라 생분해성이 우수한 계면활성제를 개발 하기 위한 연구는 증가되고 있다. 본 연구에서는 Michael addition 반응을 통하여 ester-type의 양이온 계면활성제를 합성하였다. 실온에서 촉매없이 alkyl acrylate와 1차 아민을 가지는 화합물을 합성한 뒤 dimethyl sulfate 로 4차화시킨다. 2개의 소수기와 한 개의 친수기를 갖는 HQ21과 2개의 소수기와 2개 의 친수기를 갖는 HQ22를 합성하였다. 이들 합성화합물은 1H-NMR, HR-MS 와 FT-IR로 구조를 확인하였으며 생분해성을 측정하였다.

사용후핵연료 파이로프로세싱에서는 방사성 희토류 염화물(RECl3)을 함유한 LiCl-KCl 공융염폐기물이 발생되며, 핫셀시설에서 운영을 목적으로 단순한 형태의 공융염폐기물 처리공정을 개발하는 것이 필요하다. 본 연구에서는, LiCl-KCl 공융염폐기물 내 희토류 핵종 분리/고화공정의 단순화를 목적으로 Li2O-Al2O3-SiO2-B2O3계의 무기합성매질을 이용하여 LiCl-KCl 공융 염 내 희토류 핵종(Nd)을 분리한 후 분리생성물을 바로 고화하는 시험을 실시하였다. 공융염 내 희토류 염화물(NdCl3) 대비 0.67의 무게비에 해당하는 무기합성매질의 양으로도 Nd 핵종을 98wt% 이상 분리할 수 있었고, 이 때 얻은 희토류 핵종 포집생성물은 약 50wt% 수준의 희토류 산화물 함량을 보유하고 있었으며, 이 포집생성물을 화학적 내구성이 우수한 단일상의 균질한 유리고화체로 제조할 수 있었다. 이 결과들은 LiCl-KCl 공융염폐기물 내 희토류 핵종의 분리/고화공정을 단순화하기 위한 방안수립에 활용될 수 있을 것이다.

본 연구에서는 고염/고방사성 폐액 내 함유된 주요 고방사성핵종인 Cs 제거를 목적으로 고효율의 복합 흡착제(potassium cobalt ferrocyanide (PCFC)-loaded chabazite (CHA)) 합성 및 이의 적용성을 평가하였다. 복합 흡착제는 Cs을 비롯한 다 른 입자를 수용할 수 있는 CHA를 지지체로 선정하였으며, CoCl2 및 K4Fe(CN)6 용액의 단계적인 함침/침전을 통해 PCFC를 CHA 세공 내에 고정화함으로써 합성하였다. 복합 흡착제의 합성 시 평균 입자크기가 10 ㎛ 이상의 CHA를 지지체로 사용할 경우, PCFC 입자는 안정적인 형태로 고정화되었다. 또한, 합성 시 복합 흡착제의 정제를 증가시키는 세척 방법을 최적화함으로써, 복합 흡착제의 물리적 안정성이 향상되었다. 최적의 합성법을 통해 얻은 복합 흡착제에 의한 Cs 흡착 시, 담수(무염 조건) 및 해수(고염 조건)에서 모두 빠른 흡착 속도를 보였으며, 염 농도와 무관하게 비교적 높은 분배계수 값(104 mL·g-1 이상)을 나타내었다. 그러므로, 본 연구에서 합성한 복합 흡착제는 CHA 및 PCFC가 각각 가지고 있는 물리적 안정성과 Cs 에 높은 선택성 등을 고려하여 촤적화한 소재이며, 고염/고방사성폐액에 함유되어 있는 Cs을 고효율로 신속하게 제거할 수 있음을 알 수 있다.

The feasibility of reduction of sodium intake using sun-dried salt and monosodium glutamate (MSG) was studied. Preference test was performed to evaluate the sensory properties of bean-sprout soup and vegetable rice porridge soup. Sun-dried salt and MSG might be a partial substitute for refined salt. There was a significant difference in salt taste strength between sun-dried salt and refined salt. Sun-dried salts 0.45% with MSG 0.07% resulted in the highest taste preference compared to that of sun-dried salts 0.60% without MSG in bean-sprout soup, which resulted in 23.9% reduction of sodium intake. Sun-dried salts 0.38% with MSG 0.04% resulted in the highest taste preference compared to sun-dried salts 0.53% without MSG in vegetable rice porridge soup, which resulted in 25.4% reduction of sodium intake. There seemed to be a synergistic effect on reduced usage of sodium salt when MSG was used in vegetable rice porridge and bean-sprout soup with sun-dried salt.

Effect of salt concentration (10, 20 and 30%, respectively) and fermentation temperature (10 and 20oC, respectively) on changes in quality index (VBN, Histamine, Amino nitrogen, Total viable cell counts, Coliform bacteria and E. coli counts) of culinary salted and fermented anchovy during fermentation were investigated to suggestion of fundamental documents for industrial objectives. Our results show that the effect of salt concentration on changes in quality index was not high compared with fermentation temperature in salted and fermented anchovy with below 20% of salt concentration however effect of salt concentration and fermentation temperature on quality index was not significant with 30% salt concentration. And all most whole changes of quality index were rapidly increased or decreased for 30 days of fermentation.

Zirconium(Zr) nuclear fuel cladding tubes are made using a three-time pilgering and annealing process. In order to remove the oxidized layer and impurities on the surface of the tube, a pickling process is required. Zr is dissolved in HF and HNO3 mixed acid during the process and pickling waste acid, including dissolved Zr, is totally discarded after being neutralized. In this study, the waste acid was recycled by adding BaF2, which reacted with the Zr ion involved in the waste acid; Ba2ZrF8 was subsequently precipitated due to its low solubility in water. It is very difficult to extract zirconium from the as-recovered Ba2ZrF8 because its melting temperature is 1031 oC. Hence, we tried to recover Zr using an electrowinning process with a low temperature molten salt compound that was fabricated by adding ZrF4 to Ba2ZrF8 to decrease the melting point. Change of the Zr redox potential was observed using cyclic voltammetry; the voltage change of the cell was observed by polarization and chronopotentiometry. The structure of the electrodeposited Zr was analyzed and the electrodeposition characteristics were also evaluated.