In this study, we selected a DC servo motor as an actuator of the marine diesel engine governor and constructed the position control system of the DC servo motor using the algorithm proposed by authors. Next, we proposed an another method to construct an adaptive control system for marine diesel engine by regarding the controlled system including the DC servo motor as a second order controlled system and verified the validity of this method through the real time control responses. Finally, the results have shown a good response characteristic

This paper is an experimental study to investigate utility of ultrasonic treatment of fuel oil in diesel engine. Experiment was carrid out to clarify the effect of ultrsonic vibration on the characteristics of maximum pressure, fuel consumption ratio, smoke, BMEP and torque. The result obtained are as follows: 1. In the case of given ultrsonic vibration, the maximum pressure is increased in all experimental conditions. 2. In the case of given ultrsonic vibration, the decrease effect of fuel consumption rate is increased at low rpm. 3. The generation quantity of soots is increased according to load. In the case of given ultrsonic vibration, the decreased quantity of soots does not very according to load. 4. In the case of given ultrsonic vibration, the BMEP and torque are increased at low load.

In this paper, combustion characteristics and engine performance varying with blending rate of fish oil using five test fuels, e.g.pure diesel oil and four types of sardine-oil-blended diesel oils, their blending rates by weight being 20%, 40%, 60% and 80% respectively, and operating condition of engine, were investigated experimentally both in the constant volume combustion bomb and in the engine. The results are summarized as follows: 1) In the bomb, the influence of temperature on ignition delay of sardine-oil-blended diesel oils was larger than that of pure diesel oil, and it tended to increase as the blending rate of fish oil increase sardine-oil-blended diesel oils. As far as the influence of pressure on ignition delay concerns, there was no significant difference with all the test fuels. 2) In the engine, the ignition delay of fish-oil- blended diesel oils was longer than that of pure diesel oil, and it tended to increase as the blending rate increases. In the bomb, the ignition delay in high temperature showed no significant difference between with pure diesel oil and with fish-oil-blended diesel oils, and it was especially short with 60% fish-oil-blended diesel oil. In low temperature, however, the delay became longer as the blending rate increase. 3) The combustion duration was shorter with fish-oil-blended diesel oils than with pure diesel oil and it became a little shorter as the blending rate increases. 4) The rate of fuel consumption showed no significant difference between with fish-oil-blended diesel oils and with prue diesel oil, although calorific value of fish oil was lower than that of diesel oil. 5) Smoke density in exhaust gas was lower with fish-oil-blended diesel oils than with pure diesel oil and the higher the blending rate was, the lower the smoke density became

열선유속계를 이용하여 디이젤 기관 연소실내의 한점에서 유속을 측정한 결과는 다음과 같은 결론을 얻었다. 1. 연소실내의 유동은 cylinder의 원주방향의 속도 성분이 크며, 유속변화는 밸브 timing과 피스톤 속도등에 밀접한 관계가 있다. 2. 유속은 흡입시부터 증가하여 압축행정중 흡입밸브가 닫히는 60˚ABDC에서 최대치를 갖고 이후 피스톤의 속도가 감소함에 따라 유속도 감소하여 팽창행정중 배기 밸브가 열리는 120˚ATDC에서 다시 증가하였다. 3. 평균유속은 shroud 밸브 사용시가 no shroud 밸브 사용시보다 낮지만 shroud 밸브 사용시 흡입행정에서 난류강도가 가장 크게 나타났다. 4. 90˚shroud 밸브 사용시가 120˚shroud 밸브 사용시보다 난류강도는 더 크고, 90˚shroud의 180˚위치에서 난류강도가 제일 크게 나타났다.(이 논문의 결론부분임)

국산 소형어선용 예연소실식 디이젤기관에 혼합연료유(정유+중유)를 사용할 경우 혼합연료유의 성질, 연소특성 및 기관성능에 관하여 실험한 결과를 요약하면 다음과 같다. 1) 혼합연료유의 혼합비율(중량비율)이 증가함에 따라 비중은 선형적으로 증가하였고, 점도-온도 곡선은 Walther-ASTM 식과 일치하였으며, 착화성지수인 CCAI의 값은 기울기 1.0에 가까운 직선으로 증가하였다. 2) 동일운전조건에서 착화지연은 CCAI의 값이 810(혼합비율 60%)까지는 미소하게 증가하였으나, 그 이상의 값에서는 현저하게 증가하였다. 따라서, 혼합연료유의 착화성을 나타내는 CCAI의 값은 810 이상에서 적용하는 것이 타당하다. 3) 연소최고압력은 혼합비율 40%까지 증가하다가 감소하였으며, 그을음농도는 60%부터 현저하게 증가하였으므로, 본 실험에서 무그을음 연료비절감의 안전운전 혼합비율은 50%가 적당하다

Ifis recommended that the injection rate should be accurate and reliable in the input data of the performance simulation in diesel engine. Matsuoka Sin improved W. Bosch's injection ratio measurement system. Matsuoka Sin reduced length of the test pipe and set the orifice. However, it was not measured accurately to measure the injection ratio due to reflection wave. In the present thesis, the improved measurement system with combination of the conventional W. Bosch type injection ratio measurement system and Matsuoka Sin type corrected W. Bosch type was practically made. The location of orifice and throttle valve was modified and set one more back pressure valve in order to reduce the effect of reflection wave. The results according to injection condition of multi-hole nozzle are following: 1. Measurement error of injection ratio measurement system in this thesis was ± 1 %, therefore, its reliability was good. 2. The form of injetion ratio is changed from trapezoidal shape to triangle shape with increase of revolution per minute when injection amount is constant. 3. In the case of constant rpm, the initial injection ratio is almost constant regardless of the amount, meanwhile the injection period becomes longer with increase of the amount. 4. The injection pressure of nozzle isn't largely influenced with injection ratio in the case of constant injection amount and rpm, otherwise the initial injection amount is increased by 3-4% when the injection pressure is low. 5. The injection ratio isn't nearly influenced with back pressure.

(1) 디이젤기관용 대체연료로서 혼합유가 디이젤유의 연료에 대한 특성을 검토하였다. (2) 혼합유로서 디이젤기관을 운전할 경우 배기가스량은 디이젤유보다 평균 8% 정도 많음을 나타내었다. (3) 혼합유로서 디이젤기관을 운전할 경우 디이젤유에 비하여 연료소비량이 약 3% 정도 증가하였다. (4) 정미열효율에 있어서는 디이젤유와 혼합유는 거의 비슷한 상태를 나타내었다.

전자식전발분사노즐로 급속압축장치 내에서 실현한 축대칭 자유분무.화염에 고속도 사진의 화상해석을 적용하여 다음과 같은 결론을 얻었다. 1. 고속도 사진의 화상해석에 의해 구한 디이젤분무의 축방향의 연료농도분포는 분무의 선단부를 제외하면 준정상이론에 의한 분포와 정성적으로 일치한다. 2. 화염중심축방향의 그을음 농도는 연과의 농도가 비교적 낮은 분무의 선단부에서 높은 농도를 나타내며, 그 농도는 거의 분사종료시에 최대로 되어, 그 후 시간경과에 따라 저하한다. 3. 양파모델을 축대칭 분무.화염에 적용하여 분무.화염내부의 반경방향의 그을음 농도와 연료농도분포를 비교해 보면 그을음 농도의 가장 높은 부분은 연료농도가 가장 높은 중심부보다 화염반경의 2/3의 위치에서 최대로 되었다

To investigate the relation of NOx emission and consumption rate in a direct injection diesel engine with a multihole nozzle under same fuel consumption and rpm, a naphthyl ethylenediaming method on NO, emission and Tektronix oscilloscop on the indicator diagrams have been used. Comparisons of the NOx emission and fuel consumption rate made on various conditions have led to the fllowing results. 1. The higher the injection pressure in the later injection time the lower NOx emission and the fuel consumption rate have been attained. 2. By the change of nozzle hole diameter under the same injection pressure, the NOx emission was much more lowered in the small diameter than large one, but fuel consumption rate was in inverse proption to the NOx emission. 3. The effect of injection spray angle, 1ndn on NOx emission, fuel consumption rate under same injection time and injection pressure was neglectable.

This paper examines the effect of COVID-19 pandemic on the Philippine stock exchange, peso-dollar rate and retail price of diesel using robust least squares regression and vector autoregression (VAR). The robust least squares regression using MM-estimation method concluded that COVID-19 daily infection has negative and statistically significant effect on the Philippine stock exchange index, pesodollar exchange rate and retail pump price of diesel. This is consistent with the results of correlation diagnostics. As for the VAR model, the lag values of the independent variable disclose significance in explaining the Philippine stock exchange index, peso-dollar exchange rate and retail pump price of diesel. Moreover, in the short run, the impulse response function confirmed relative effect of COVID-19 daily infections and the variance decomposition divulge that COVID-19 daily infections have accounted for only minor portion in explaining fluctuations of the Philippine stock exchange index, peso-dollar exchange and retail pump price of diesel. In the long term, the influence levels off. The Granger causality test suggests that COVID-19 daily infections cause changes in the Philippine stock exchange index and peso-dollar exchange rate in the short run. However, COVID-19 infection has no causal link with retail pump price of diesel.

DeNOx experiments for the effects of hydrocarbon additives on diesel SNCR process were conducted under oxidizing diesel exhaust conditions. A diesel-fueled combustion system was set up to simulate the actual cylinder and head, exhaust pipe and combustion products, where the reducing agent NH3 and C2H6/diesel fuel additives were separately or simultaneously injected into the exhaust pipe, used as the SNCR flow reactor. A wide range of air/fuel ratios (A/F=20~40) were maintained, based on engine speeds where an initial NOx level was 530 ppm and the molar ratios (β=NH3/NOx) ranged between 1.0~2.0, together with adjusting the amounts of hydrocarbon additives. Temperature windows were normally formed in the range of 1200~1350K, which were shifted downwards by 50~100K with injecting C2H6/diesel fuel additives. About 50~68% NOx reduction was possible with the above molar ratios (β) at the optimum flow #1 (Tin=1260K). Injecting a small amount of C2H6 or diesel fuel (γ=hydrocarbon/NOx) gave the promising results, particularly in the lower exhaust temperatures, by contributing to the sufficient production of active radicals (OH/O/HO2/H) for NOx reduction. Unfortunately, the addition of hydrocarbons increased the concentrations of byproducts such as CO, UHC, N2O and NO2, and their emission levels are discussed. Among them, Injecting diesel fuel together with the primary reductant seems to be more encouraging for practical reason and could be suggested as an alternative SNCR DeNOx strategy under diesel exhaust systems, following further optimization of chemicals used for lower emission levels of byproducts.

Due to the increasing sewage sludge generation from wastewater treatment facilities, sewage sludge has been reconsidered as a renewable energy source in various ways. Lipid extraction from sewage sludge is an applicable method for biodiesel production. Higher biodiesel production yields can be achieved through the improvement of lipid recovery efficiency. Although sewage sludge has different features due to its types and steps in treatment plants, lipid content of sewage sludge generally ranges from 10 to 15%. Among solvent extraction methods, the highest lipid recovery efficiencies were observed for chloroform-methanol extraction: 13.6-14.6% for primary sludge, 10.6-12.1% for waste-activated sludge, and 2.9-4.2% for digested sludge. The extraction residue of sludge can be used as biosolid refuse fuel (bio-SRF). After lipid extraction, the residue had decreased volatile matter and carbon content. Consequently, the calorific value of the residue decreased by 3,000 kcal/kg. The level of calorific value can be available to use bio-SRF.

2016년부터 배출통제지역(ECA : Emission Control Atea)을 운항하는 선박에 대하여 배출되는 NOx(질소산화물) 및 SOx(황산화 물)의 배기량 감소규제가 강화되었다. 상기의 규제 물질 중 NOx를 제거하는 탈질장비 중 선택적 촉매 환원(SCR : Selectivity Catalytic Reduction) 시스템은 효율이 높고 상업적으로 많이 활용되고 있으나, 높은 온도에서 요소수가 활성화되는 단점이 있다. 이에 초미세기포를 이 용하여 낮은 온도에서도 반응할 수 있는 요소수 및 요소수 활성화 기기를 개발하여 상기의 문제점들을 최소화 할 수 있도록 하였다. 또한 SCR 시스템의 효율성을 향상시키는 방안을 마련하기 위하여, ANSYS-CFX package를 이용한 전산유체역학(CFD : Computational fluid dynamics)기법을 사용하였다. Navier-Stokes 방정식을 해석의 지배방정식으로 적용하여 SCR 시스템의 점성유동해석 시뮬레이션을 수행하였 다. SCR 시스템의 형상은 CATIA V5를 사용하여 3D 모델링을 하였고, SCR 시스템의 효율성을 비교하기 위해 요소수 분사 노즐의 위치를 요소수 분사 노즐은 배기관의 입구로부터 1/3, 1/2, 2/3로 변경하며 확인하였다. 또한, 노즐의 분사구 수가 SCR 시스템의 효율에 미치는 영향 을 확인하기 위하여 분사구 수가 4, 6, 8개일 경우를 시뮬레이션 하여 비교․분석하였다. 시뮬레이션 결과 배기관 입구에 가까울수록, 분사구 수가 많을수록 효율이 향상됨을 확인하였다.

Subcritical hydrolysis followed by methyl estrification was used to produce bio-diesel from low valued waste cooking oil at mild reaction conditions in this study. More than 90% fatty acid methyl esther (FAME) conversion was achieved by subcritical hydrolysis without using catalysts at 275℃ for 45 minutes. The highest conversion to linoleic acid (C18:2) was obtained at this condition. The higher content of free fatty acid (FFA) in waste cooking oil resulted in higher conversion to FAME. It was also observed more prominent at high temperature due to auto catalytic behavior of FFA. FAME yield found about 92% without using catalyst; whereas 98% yield was obtained using 80% TiO2 loading S-TiO2/MCM-41 catalyst at 220℃ and 20 minutes. The amount of FAME increased may be due to trans-esterification of un-reacted TG, DG, and MG with methanol remained during the hydrolysis stage. The higher FAME conversion means the better quality bio-diesel.

We are now currently facing serious climate changes such as super typhoon, flood, intense heat, severe cold, super hurricane, drought, desertification, destruction of ecosystem, marine pollution, reduction of food production, destruction of tropical forests, exhaustion of water resources, climate refugees, etc. All of the above mainly derive from greenhouse gas exhaustion. Such harmful consequence might directly affect mankind’s sustainable development. If we keep using resources that emits greenhouse gases, the global temperature will rise about 3.2℃ by year 2050. In case of 3℃ rise in temperature, it will result in abnormal climate which will bring about severe property damage. Moreover, 20~50% of the ecosystem will become extinct. As Korea’s economy increasingly expands, so do our energy consumption rises. And because of the consequences that can be driven by increasing rate of resource use, not just Korea itself, but also the whole world should seriously concern about greenhouse gases. Although agricultural division only takes up about 3.2% of total greenhouse gas emission, the ministry of Agriculture, Food and Rural Affairs are taking voluntary actions to gradually reduce CO2 and so does each and every related organizations. In order to reduce CO2, introduction of new and renewable energy in farm house warming is crucial. In other words, implementing wood-pellet boiler and geothermal heat boiler can largly reduce CO2 emission compared to diesel boiler. More importantly, not only wood-pellet and geothermal heat is pollution-free but they also have economic advantages somewhat. In this thesis, the economic advantage and sustainablity will be introduced and proved through comparing practical analysis of surveyed farm house under structure employing wood-pellet boiler and geothermal heat boiler with Agriculture-Economic Statistic of 2012 who uses diesel boiler.

Ce(1-x)Zr(x)O2 catalysts were investigated for bio-diesel production from oleic acid using catalytic deoxygenation. In this study, deoxygenation reaction has been carried out at 300 oC under 1 bar of 20% H2/N2 pressure in batch mode. Ce(1-x)Zr(x)O2 catalysts were prepared by co-precipitation method. Ce0.6Zr0.4O2 catalyst showed the highest oleic acid conversion and C9~C17 selectivity. It has been found that the deoxygenation reaction depends strongly on the reduction property and depends partly on the crystallite size of Ce(1-x)Zr(x)O2. Thus, Ce0.6Zr0.4O2 can be selected as the most promising catalyst for deoxygenation reaction.

Diesel DeNOx experiments using the SNCR process were performed by directly injecting NH3 into a simulated engine cylinder (966 cm3) for which a diesel fuelled combustion-driven flow reactor was designed by simulating diesel engine geometry, temperature profiles, aerodynamics and combustion products. A wide range of air/fuel mixtures (A/F=20∼45) were combusted for oxidizing diesel flue gas conditions where an initial NOx levels were 250~900 ppm and molar ratios (β=NH3/NOx) ranged from 0.5∼2.0 for NOx reduction tests. Effective NOx reduction occurred over a temperature range of 1100∼1350 K at cylinder injections where about 34% NOx reduction was achieved with β=1.5 and cylinder cooling at optimum flow conditions. The effects of simulated engine cylinder and exhaust parts, initial NOx levels, molar ratios and engine speeds on NOx reduction potential are discussed following temperature gradients and diesel engine environments. A staged injection by NH3 and diesel fuel additive is tested for further NOx reduction, and more discussed for practical implication.

The feature of asthma are airway inflammation (AI), reversible airway obstruction, and an increased sensitivity to bronchoconstricting agents, elevated airway hyperresponsiveness (AHR), excess production of Th2 cytokines, and eosinophil accumulation in the lungs. This study was performed to investigate if oral administration of Scutellaria baicalensis Georgi water extracts (SBG) have the antiasthmatic potential for the treatment of asthma. Asthmatic HI and AHR were induced by systemic sensitization to ovalbumin (OVA) with intratracheal instillation with 0.1 mg/mL of diesel exhaust particles (DEP) suspension once a week for 10 weeks in BALB/c mice. SBG was orally administered with the concentraion of 200 mg/kg 5 days a week for 10 weeks. Long-term SBG treatment suppressed the eosinophil infiltration into airways from blood, the asthmatic AI and AHR by attenuating the production of cytokine IL-4, IL-5 and IL-13, histamine and OVA-specific IgE. Our data suggest that SBG has inhibitory effects on AI and AHR in a mouse model of asthma, may act as a potential Th2 cytokine antagonist, and may have a therapeutic effect on allergic asthma.

The emissions of several air pollutants (NOx, CO, VOCs, etc.) for the replacement of all diesel buses by Compressed Natural Gas (CNG) buses were estimated in the Busan Metropolitan Area (BMA). These emissions were calculated from emission factors considering the different driving speeds with bus routes, distance traveled, and deterioration factors. For the purpose of this study, three categories of fuel type were selected: (1) the combination of diesel (65%) and CNG buses (35%) (DSL+CNG case), (2) all diesel buses (DSL case), and (3) all CNG buses (CNG case). The emissions of NOx and CO in the CNG case were estimated to be significant decreases (by about 50% and 98%, respectively) relative to the DSL case. Conversely, the emission of VOCs (980.7 ton/year) in the CNG case were a factor of 3.3 higher than that (299.8 ton/year) in the DSL case. In addition, the diurnal variations of emissions between two city buses (e.g. diesel and CNG) and all other vehicles were distinctly different because the two city buses operate at a regular time interval. Our overall results suggest the possibility that the pollutant emissions from the CNG buses can exert less influence on air quality in the target area than those from the diesel buses.