In relation to the development of automatic discharging and grinding system producing eco-friendly composite fertilizer raw materials, the performance test was proceeded. and We had obtained the following results. 1. Of the evaluation items set as performance indicators for this technology development, the “grinding capacity” of the composite fertilizer roll mill is higher than the current market-sufficient performance (1500kg/hr) of 1800kg/hr.For “grind particle size”, results of less than 1.8 mm on average were obtained, which is smaller than market-sufficient performance (average less than 2 mm). 2. As a result of the evaluation of “1batch 400kg discharge time”, the results of less than 10min/1bach were obtained, which is shorter than the market satisfaction performance (15min/1bach).

Natural gas is the most realistic fuel among eco-friendly fuels. Natural gas production is limited, and in Korea, it is supplied and utilized in the form of liquefied natural gas (LNG). In the case of LNG, the vaporization point is 163 degrees below zero, so ordinary metal cannot be used due to its brittleness. The International Maritime Organization (IMO) defines metals that can be used in the IGC Code, and is used for storage containers, transportation containers, etc. based on the metals. Welding is essential in the manufacture of large structures such as LNG storage tanks. In this study, weldability studies related to cryogenic materials were conducted. In Part I of this study, high-manganese steel and part II were studied for two types of stainless steel (STS304L, STS316L), and in Part III, aluminum (AL5083). During laser welding, the shape of the Bead on Plate (BOP) was analyzed, and a total of nine cases were analyzed using laser power and welding speed as variables. It was confirmed that the penetration and the width of the welding width were linearly proportional to the amount of heat input. Based on this study, it is possible to conduct a follow-up study to find the optimal welding conditions for butt welding and fillet welding.

As the part of efforts to respond to the environmental pollution, the demand for clean energy is increasing. Natural gas is one of the most realistic alternatives, and interest in the storage and transportation containers to utilize the natural gas is growing. The production area of ​​natural gas is limited, and in Korea, it is imported in the form of liquefied natural gas. LNG is a cryogenic state with a vaporization point of -163°C, so the ordinary metal cannot be used due to its brittleness. The international maritime organization (IMO) defines the metals that can handle LNG in the IGC Code, and the research is ongoing. This study was a preliminary study to check the weldability of related metals and confirmed the shape of bead on plate (BOP) during the laser welding for each material. In part I, a study was conducted on the high manganese steel, and in part II, a study was conducted on the materials of STS304L and STS316L among the stainless steel. Based on this study, it can be used as an optimal welding condition for the butt and fillet welding.

As demand for eco-friendly energy increases, demand for natural gas and Liquefied natural gas (LNG) storage technologies continues to increase. LNG is a cryogenic environment with a temperature of -163°C, so ordinary metals cannot be used due to brittleness. Accordingly, IGC Code designates the cryogenic materials such as Invar, STS304L, Al5083-0, and High Manganese Steel. For fabricating those materials, research on welding possibility is the most important. Thus this study focused on the possibility of laser welding of the cryogenic materials. The weldability of High Manganese Steel was researched in this paper, the shape and the dimensions of the beads after bead on plate (BOP) welding were observed. The experiment was conducted on a total of 25 cases with laser power and welding speed of 5 cases each, and the width, height, and penetration of the beads were confirmed. It was confirmed that the paramenter of bead increased linearly with the laser power, and the paramenters of bead increased linearly with decreasing welding speed. Based on this study, high manganese steel can be applied in various industries by applying it to butt welding.

본 연구에서는 국내 유통중인 가정간편식 샤브샤브 밀키트를 원료별(쇠고기, 숙주, 쌈추, 새송이버섯, 배추, 단호 박)로 구분하여 미생물 오염도를 알아보기 위해 일반세균수(total aerobic bacteria), 대장균군(coliform)/대장균(E. coli), 효모 및 진균류(fungi), 황색포도상구균(S. aureus), 및 바실러스세레우스(B. cereus)에 대한 정량적 분석을 실시하였다. 아울러, 살모넬라(Salmonella spp.)와 리스테리아 모노사이토제네스(L. monocytogenes)에 대한 정성적 분석을 실시하였다. 샤브샤브 밀키트 원료의 일반세균수(총균 수)는 3.98-6.50 log CFU/g로 검출되었다. 특히, 쇠고기의 경우 6 log CFU/g 이상의 균이 검출되었으며 숙주, 단호박, 배추의 경우 5 log CFU/g 이상의 균이 검출되었다. 진균류 (곰팡이/효모)의 오염도는 2.78-3.52 log CFU/g 수준으로 검출되었다. 대장균군은 일반세균수와 마찬가지로 쇠고기에서 3.28 log CFU/g으로 가장 높게 검출되었으며 기타 신선야채류의 경우 2 log CFU/g 수준으로 검출되었다. 대장균은 6가지 원료 모두에서 검출되지 않았다. S. aureus 는 쇠고기와 쌈추를 제외한 숙주, 배추, 새송이버섯, 단호박에서 1.33-1.71 log CFU/g의 수준으로 검출되었다. B. cereus는 쌈추를 제외한 모든 원료에서 1.15-2.01 log CFU/g 의 수준으로 검출되었다. L. monocytogenes는 새송이버섯을 제외하곤 모든 원료에서 25-50%의 양성검출을 보였고 Salmonella는 모든 원료에서 음성으로 나타났다. 본 연구 결과의 종합적 분석시, 쇠고기 원료에서 일반세균수와 대장균군 기준치를 초과하였고 황색포도상구균과 바실러스 세레우스는 대부분의 원료에서 식품안전을 위협할만한 위험한 수준은 아니었으나 검출되었고 저온성식중독균인 리스테리아모노사이토제네스 역시 일부 원료에서 양성을 보였기 때문에 본 제품의 원료별 생산단계에서의 살균·소독의 적절한 공정과 섭취시 충분한 열처리를 통해 잔존미 생물을 사멸하는 것이 긴요하다. 또한 조리기구 및 조리 종사원 손에 의해 최종 식품을 공정하면서 미생물이 전 파될 가능성이 있으므로 최종 식품의 안전성을 확보하기 위해 오염된 접촉면에 의한 교차오염을 최소화하며, 개인위생수준의 개선, 조리기기의 분리사용과 세척 및 소독을 통한 조리기기의 청결유지가 무엇보다도 중요하다. 아울러 본 연구의 미생물오염수준 자료는 가정간편식밀키트의 미생물위해평가(Microbial Risk Assessment) 의 기초자료로 활용될 수 있을 것으로 사료된다.

In this study, air scouring cleaning was selected and applied among 5 small blocks (S1~S5) in domestic S cities to analyze the cleaning effect of particles causing discoloration. In order to identify the cleaning effect, 10 locations were selected as water quality investigation point, such as the stagnant or water mains ends. Removal of solids, variation of particle components, weight and concentration were analyzed. And the level of the cleanness of the surface inside water mains using endoscope was investigated. As a result of analysis, the solids discharged after cleaning were mainly sand and gravel, pieces related to pipe materials, and corrosion products. As a result of analyzing the concentrated particles of the filter before and after cleaning, it was found that the change in discoloration on the filter was large. In addition, as a result of comparing the weight and the concentration of the particles, it was found that the particles causing discoloration were significantly removed after cleaning. From the results of the endoscopy, it was confirmed that most of the precipitated and accumulated dark yellow discoloration matters inside water mains were removed through cleaning. Therefore, it seems that the particles causing discoloration in water decreased after cleaning. Therefore, it is expected that, if properly cleaning was applied, matters that cause discoloration can be removed from the water mains, and customer's complaints can also be reduced through water quality improvement.

초음파 탐상은 다양한 콘크리트 구조물의 비파괴검사에서 활용된다. 본 연구에서는 골재형상을 고려한 골재-모르타르 모델 생성과 초음파 전파 해석을 수행하였다. 실제 골재형상을 반영하기 위해 이미지처리를 통한 골재-모르타르 단면으로부터 모르타르와 골재 영역을 파악하고, 영역 경계형상을 보존하면서 격자를 생성하는 기법을 개발하였다. 개발된 기법에서는 모든 격자가 4각형으로 생성된다. 골재-모르타르 모델을 통해 초음파 전파 해석을 수행하였고 모델을 반무한체로 간주하기 위해 CALM 기반 경계흡수 조건을 적용하였다. 골재 및 결함을 포함한 이미지로부터 격자를 생성한 뒤, 결함 영역에 포함된 격자를 제거하여 공극결함을 모사하였다. 본격적인 결함탐지 전 선행 해석을 통해 모델 동특성을 고려한 적절한 가진 주파수를 결정 및 가진 신호형상을 설계하였다. 이후 case 별 초음파 전파 해석을 통해 신호를 획득하고 신호 에너지 맵핑 작업을 통해 내부 결함을 가시화 하였다. 가시화 결과, 골재에 의한 다수 반사 및 산란현상이 관찰되지만 결함부에서 신호 에너지는 가장 높게 나타났으며 모든 해석 case에서 결함위치 추정이 가능하였다. 또한 균열의 경우 형상파악도 가능하였다.

Various electronic control parts and devices installed in electric vehicles have greatly improved the convenience of occupants, but electromagnetic waves emitted from electronic devices have greatly increased concerns about malfunctions, deterioration of performance, safety accidents, etc. There are two models of analysis. Case A is symmetrical about one axis of rotation. Case B has two axes of rotation. In this study, a flow analysis was conducted to find excellent flow conditions in the mixing process to develop a paint with excellent electromagnetic shielding and thermal insulation performance. The results of the flow analysis are reflected in manufacturing specifications and are intended to be used to develop high-quality systems.

Defects in most structures can be generated not only on outside but also on inside or on the back-side during the manufacturing or construction process. Also they cause the growth of defects due to operation of various complex environments and structures will be destroyed eventually. In order to improve the reliability of the structure, the detection and size-estimation of defects should be investigated. In this paper, as an extension of previous studies on surface defects, two-dimensional artificial backside cracks (blind cracks) into paramagnetic material were evaluated by using the same aluminum probe. The potential drop at the defect position is distributed in the n-shape in the case of the back defect, which is different from results of the surface defect (u-shape). The potential drops at the defect position are measured with the largest value. The potential drop ratio (Vcmax/Vs) for the defective position is used as a parameter to predict the thickness (l) of defect position.