검색결과

검색조건
좁혀보기
검색필터
결과 내 재검색

간행물

    분야

      발행연도

      -

        검색결과 1,435

        301.
        2019.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Carboxylated multi-wall carbon nanotubes (MWCNTs-COOH) was functionalized with 3-amino-5-phenylpyrazole (MWCNTs- f) and characterized by FTIR, EDX, SEM, XRD and TGA. The MWCNTs-COOH and MWCNTs-f were used for the adsorption of Cd(II), Hg(II), and As(III) ions from aqueous solutions. Additionally, to study the influence of pH, adsorbent dose, and initial ions concentration on the adsorption process, the central composite design (CCD) was applied. The quadratic model was used for analysis of variance and indicated that adsorption of metal ions strongly depends on pH. Timedependent adsorption can be described by the pseudo-second-order kinetic model, and adsorption process was modeled by Langmuir isotherm for the adsorbents. Thermodynamic analysis showed that the adsorption of Cd(II), Hg(II) and As(III) ions were spontaneous and endothermic. Moreover, the competitive adsorption capacities of the heavy metal ions were slightly lower than noncompetitive ones. The same affinity order was observed under noncompetitive and competitive adsorption: As(III) > Cd(II) > Hg(II) in the case of MWCNTs-f. Desorption study revealed the favorable regeneration ability of adsorbents powders, even after three adsorption–desorption cycles.
        5,500원
        302.
        2019.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The blood preparation is important for management and classification. Because the work bench for sorting blood is not produced domestically, we have developed a work bench to classify blood through this study. Single coil system was developed to control cooling efficiency and temperature distribution. And evaporator and heater were used to reduce condensate discharge. This allow us to maintain a constant temperature and the condensation remainder below 1L. This study is expected to expand to other bio-equipment development.
        4,000원
        303.
        2019.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        β-mannanase from Trichoderma reesei was purified by DEAE Sephadex A-50 ion exchange chromatography and Sephadex G-100 gel chromatography. The molecular weight was determined to be 54 kDa by tricine SDS-PAGE. Trigonella foenum-graecum galactomannan was hydrolyzed by the purified β-mannanase, and then the hydrolysates were separated by Bio-Gel P2 chromatography. The main hydrolysates were composed of D.P. (degree of polymerization) 2, 3, and 4, 6 galactomanno-oligosaccharides. To investigate the effects of Trigonella foenum-graecum galactomanno- oligosaccharides on in vitro growth of L. plantarum, were cultivated individually on a modified-MRS medium containing carbon sources such as low- and high-molecular-weight galactomanno-oligosaccharide. Lactobacillus plantarum grew 1.8-fold after treatment with high- and low-molecular-weight galactomanno-oligosaccharides, compared to 1.3-fold for those with standard MRS medium. Bacteriocin was purified by Sephadex G-100 gel chromatography and determined to be 122 kDa by tricine SDS-PAGE. The bacteriocin activated doubly more effectively after treatment with galactosmanno-oligosaccharides compared to those with standard MRS medium. Bacteriocin showed antimicrobial activity against Staphylococcus aureus. The inhibitory compound lost activity when heated to temperatures greater than 30oC and when inhibited to pH changes that lowered the pH below 4 or raised it above 5. Furthermore, its effects were inhibited by treatment with proteolytic enzymes.
        4,000원
        304.
        2018.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this study, 2-hedroxyethyl methacrylate (2-HEMA) was graft synthesized on water-dispersed polyurethane using polytetramethylene ether glycoll (PTMG), and then the film of resin was prepared and the physical properties of polyurethane resin were measured. The mechanical properties of the synthesized polyurethane resin were measured by using FT-IR, UTM, adhesion performance measuring instrument. As a result of tensile strength measurement, the tensile strength of HPUD4 with high 2-HEMA content was increased to 5.05 kgf / ㎟, the elongation was measured as 285% of the HPUD1 sample not containing 2-HEMA and adhesive strength of HPUD4 sample was measured at 9.1 sec to 635 psi.
        4,000원
        305.
        2018.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        A novel, unique, and effective method for carbon nanotube (CNT) dispersion by the free arc stimulation is proposed. CNTs are introduced as an aerogel into the air space via the dispersion method and can be utilized as a solution by adding it to solvents. The volume of the original generated CNT aerogel with a high-volume expansion ratio displays a performance two orders of magnitudes better than that of raw CNTs, which is considered a powerful characterization of the dispersion effect. The CNT aerogel, which was observed by scanning electron microscopy also showed a satisfactory dispersion morphology. Its structure and properties were tested before and after dispersion by Raman spectroscopy and great consistency was observed, which proved that the CNTs were undamaged. This approach may greatly promote the large-scale application of CNTs.
        4,000원
        306.
        2018.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        자외선차단 화장품은 기능성 화장품 중의 하나로서, 유·무기 자외선차단물질이 함유되어 있다. 무기계 자외선차단제는 주로 산화아연, 이산화티탄 등이 있다. 무기계 자외선차단제는 입자의 지름이 60 ~ 100 nm로 자외선 A, B의 차단능이 좋은 것으로 알려져 있다. 또한 자외선을 포함한 태양광선에 대해 비활성이 크고 안전성이 우수하다. 그리고 유기계 자외선차단제처럼 피부에 흡수 또는 축적되지 않으므로 피부 자극이나 알레르기를 유발하지 않는다. 본 연구에서는 판상 무기안료인 마이카, 자외선차단 효과를 갖는 이산화티탄 나노입자, 소수성 실리카를 각각 계면활성제로 표면처리 하였고, 각 물질의 전하 차이에 따른 비화학적인 상호 인력 작용에 의해 마이카에 이산화티탄 나노입자, 실리카를 물리적으로 흡착시켰다. 이후, 소수성 표면처리제인 실란을 표면처리 하여 소수성을 갖는 자외선 차단 판상 마이카 복합체를 제조하였다. 자외선 차단 판상 마이카 복합체는 일반적인 나노입자 이산화티탄의 응집성을 개선하고 균일한 분산에 따른 자외선차단 효과가 증대되었으며, 소수성으로 표면처리를 하여 화장품 제형에서의 분산안정성을 크게 개선할 수 있었다. 안료의 표면전하는 제타전위로 평가하였으며, 제조된 자외선차단 마이카 복합체의 특성 평가는 FE-SEM, XRD, FT-IR, UV-VIS 등으로 확인하였다.
        4,000원
        307.
        2018.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        연구에서 Poly(ethylene-co-vinylalcohol) EVOH 중공사막은 열유도상분리(TIPS)법을 이용하여 제조하였다. 다양한 조건에서 제조된 모든 분리막에서 액-액 상분리에 의해 기공이 서로 연결되어 있는 스폰지 구조가 관찰되었다. 글리세롤과 PEG200은 TIPS 방법에서 희석제로 사용하였고, 냉각조에 글리세롤을 혼합한 냉매를 사용하여 중공사 외표면의 기공을 조절하였다. 또한 혼합냉매의 온도를 높여 큰 기공의 형성을 유도하였다. 본 연구에서는 고분자의 농도, 희석제, 냉각조의 영향에 따른 분리막의 구조, 투과도, 기계적 강도에 대해 실험을 통해 알아보고 상호관계에 대해 심도 있게 연구하였다.
        4,200원
        308.
        2018.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        본 연구에서는 한외여과 polysulfone (PSf) 중공사막에 첨가제를 섞는 방법을 통해 친수성 증가에 따른 분리막 특성 및 성능을 향상하고자 하였다. 15 nm 크기의 fumed silica (FS)를 0.1, 0.3, 0.5 wt%로 방사 용액에 분산시켜 혼합 매트릭스 분리막을 제조하였다. 단면 및 표면상태를 확인하기 위해 SEM 분석을 진행하였으며, FS가 함유될수록 중공사막의 평균 기공 반경이 4 nm 이상 증가하는 것을 확인하였다. 또한, 분리막의 친수성 분석을 위해 접촉각 측정을 진행하였으며, FS 함유로 분리막의 친수성이 높아진 것을 확인하였다. 수투과도의 경우 FS가 섞인 분리막은 91~96 LMH 수준을 보였으며 PSf 분리막보다 5~11%의 증가율을 보였다. 내오염성 평가에서도 친수도가 상승한 FS 혼합 중공사막 표면에 소수성을 띄는 BSA가 흡착되지 못하여 상대 유량 감소율이 PSf 단일막 보다 낮아졌음을 확인하였다.
        4,000원
        311.
        2018.11 구독 인증기관·개인회원 무료
        Although thin-film nanocomposite membranes (TFNs) have paved the way to develop high-performance reverse osmosis (RO) membranes, scale-up production of TFNs is still challenging issue. Herein, we introduced a novel preparation method for TFNs using spray-assisted nanofiller pre-deposition (Spray method) to circumvent the limitations in conventional method. The precise control of nanofiller (ZIF-8) loading was possible by simply varying the spraying ZIF-8 concentration. Most importantly, TFNs prepared by both Spray and conventional method showed similar RO performances, while Spray method only requires ~100 times minimized amount of ZIF-8 with an unprecedentedly short deposition time (< 1 min) ever reported. Our results revealed that Spray method would be promising for the scale-up of TFNs in terms of cost, time, and controllability.
        312.
        2018.11 구독 인증기관·개인회원 무료
        Commercial polystyrene-based ion exchange membranes have simple manufacturing processes, they also possess the poor durability due to their brittleness. Poly(ethylene glycol)methyl ether methacrylate with hydrophilic side chain of poly(ethylene glycol) (PEG) was used as a co-monomer to make the membranes have improved flexibility. Hydrophilicity of the anion exchange membrane was able to be adjusted by varying the chain lengths of the PEG polymers. For the preparation of the anion exchange membranes, a porous PE substrate was immersed into monomer solutions and thermally polymerized and crosslinked. The prepared membranes were then subsequently post-aminated using trimethylamine(TMA). The prepared pore-filled anion exchange membranes were evaluated in terms of ion exchange capacity(IEC), electric resistance(ER) and water uptake.
        313.
        2018.11 구독 인증기관·개인회원 무료
        다양한 산업 부생가스에 포함되어 있는 CO를 고순도로 정제하면 고부가가치의 화학원료 및 신재생 연료로 사용되어 경제적인 효과를 기대할 수 있다. CO를 정제하기 위해서는 주로 CO2가 포함된 혼합기체로부터 CO를 분리해야 하지만 CO만을 선택적으로 투과시킬 수 있는 CO/CO2 선택성 분리막에 대한 연구는 전 세계적으로 미미한 상태이다. 본 연구에서는 CO2친화성을 갖는 성질을 도입하여 CO2의 투과를 방해하고 상대적으로 CO를 선택적으로 투과할 수 있는 분리막을 개발하고자 하였다. 유기 졸-겔 법을 이용하여 Network former(TAPM)의 아민 그룹과 network linker(HDI)의 이소시아네이트 그룹으로부터 우레아 결합이 포함된 다공성 네트워크 구조를 제조하였다. 다양한 기체에 대한 순수가스 투과테스트를 통해 투과도를 확인하였고, 분리 메커니즘을 규명하기 위해 CO, CO2,N2에 대한 흡착 등온선을 측정하였다.
        314.
        2018.11 구독 인증기관·개인회원 무료
        Carbon molecular sieve (CMS) membrane surpasses the upper-bound trade-off and plasticization phenomenon of polymer membrane. Recently, supported CMS membranes have been investigated to provide both high performance and mechanical strength. Herein, we have investigated the supported CMS hollow fiber membranes on low-cost alumina hollow fiber. To prepare the thin and uniform layers, the dip-coating parameters for intermediate and polymeric layers were varied in terms of the withdrawal rate and solution viscosity, respectively. Then, in order to confirm its feasibility in real industry, mixture gas was permeated through prepared CMS membranes. Moreover, the property of long-term stability was characterized in harsh conditions and further modified.
        315.
        2018.11 구독 인증기관·개인회원 무료
        In the epoxy resin manufacturing process, carcinogenic ECH (epichlorohydrin), IPA (isopropanol) and Biphenol-A materials has been generally used. After the reaction, byproducts containing ECH/IPA/Water is remained along with final product. But, in the recovery process, ECH and IPA forming an azeotropic mixture with water containing feed solution at any temperature condition, the recovery of high purity ECH is difficult only by distillation. Therefore, pervaporation process could be suitable countermeasure due to its mild operation condition for separation of azeotropic mixtures at the point of energy and cost saving. In this study, Alumina-PVA composite membrane was prepared for pervaporation dehydration of ECH/IPA/Water feed mixtures and pervaporation performance and stability of the prepared composite membrane was identified.
        316.
        2018.11 구독 인증기관·개인회원 무료
        반도체 제조공정 중 포토리소그래피는 반도체 제조 중 핵심 기술이며 웨이퍼위에 나노급의 패턴을 제조하는 공정이다. 웨이퍼상의 패턴이 나노급으로 작아지면서 더욱 정밀한 공정을 위하여 photo-resist 용액의 정제 기술이 매우 중요하다. photo-resist 용액 내 soft particle은 포토리소그래피 공정 중 불량을 유발하는데, 현재 개발되어진 멤브레인은 soft particle 제거 성능이 낮다. 따라서 photo-resist 용액 내 soft particle을 제거하기 위하여 PE 지지체 위에 Nylon 고분자를 함침하여 soft particle 정제 특성을 살펴보았다. 또한 팔라듐 나노입자를 합성하여 투과 특성실험에 사용하였다.
        317.
        2018.11 구독 인증기관·개인회원 무료
        Recently developed crosslinked TR (XTR) membranes as an advanced TR material exhibit high permeability and high selectivity stemming from higher rigidity due to a simultaneous and synergetic reaction of crosslinking and thermal rearrangement. The precursor crosslinkable co-HPI precursor can be dissolved in a wide range of commercial solvents indicative of an excellent processibility. Herein, a systematic spinning process, using a newly designed crosslinkable co-HPI precursor to fabricate defect-free XTR-PBOI hollow fiber membranes with inner skin layer will be discussed based on the phase inversion kinetics of nonsolvent-induced phase separation (NIPS) method.
        318.
        2018.11 구독 인증기관·개인회원 무료
        본 연구에서는 고분자인 polyacrylonitrile (PAN) 고분자에 산화 그래핀(Graphene Oxide, GO)을 첨가하여 전기방사법을 통해 나노섬유 복합막(GO-PAN)을 제조하였으며, 과량의 GO를 첨가하기 위해 표면개질 전략을 사용하였다. 계면활성제를 사용하여 GO의 표면을 간단히 변형하면 GO의 안정성 및 분산도 증가로 인해 최종적으로 분리막에 필러의 함량을 3wt%까지 증가시켰다. 이렇게 변형된 GO(mGO)의 PAN 나노섬유막으로의 도입은 원래의 PAN 나노섬유막과 GO-PAN 막에 비해 향상된 친수성과 기계적 강도를 가진다. 따라서 나노필러의 표면 개질은 최종 복합막의 성능에 영향을 미치며 이는 GO의 분산도와 상관관계가 있는 것으로 보인다.
        319.
        2018.11 구독 인증기관·개인회원 무료
        제련 산업의 공정수(15wt% 폐산용액)에는 다양한 희소 및 유가금속이 함유되어 있지만, 회수 처리기술 부족으로 폐기되고 있다. 이에 나노분리막을 적용하여 폐산용액에 잔존하는 금속들을 경제적으로 분리하고자 한다. 본 연구에서는 폐산에 적용 가능한 내산, 내열성을 가지는 나노분리막을 PSf 지지막 위에 수용액상으로 aliphatic amine과 유기상으로 trimesoyl chloride, diisocyanate계를 계면중합하여 제조하였다. 제조막의 2가 이온 플럭스는 15 GFD, 98%의 제거율, 1가 이온은 20% 이하의 제거율을 나타내었다. 내산성 평가는 황산 용액에 일별 노출한 후 투과평가를 진행하였으며, 그 결과 4주 이상 초기 성능을 유지하였다. 내산성 특성은 FTIR, XPS, FE-SEM등의 분석을 통해 확인하였다.