To remove SO2 from flue gas, a thin film nanocomposite (TFN) hollow fiber membrane was decorated with Nafion/TiO2 nanoparticles. Morphological and structural analyses of the TFN membranes were performed using FTIR, SEM, EDX, TEM, and AFM. The gas permeation experiments were performed with pure gases and a mixed gas within a pressure range of 1-3 bar and feed gas flow rate of 0.03-0.15 L/min. The obtained experimental results suggest that the addition of Nf/TiO2 nanoparticles improved the membrane performance by introducing sulfonate and hydroxyl functional groups to the membrane, and thus increased SO2 permeability and selectivity. The SO2 permeability was found to be 411-1671 GPU, while the ideal selectivities achieved for SO2/N2 and SO2/CO2 were 2928 and 72, respectively. Overall, an SO2 removal efficiency of 93% was achieved by using the Nf/TiO2 incorporated TFN membrane.

친수성을 띄는 silica 나노입자(7, 11, 15 nm)를 0.1, 0.2, 0.3 wt%의 비율로 고분자(Polysulfone)에 섞은 후, 상전이 공정에 의하여 중공사막을 제조하였다. 용매로는 N-Methyl-2-pyrrolidone (NMP)을 사용하였다. 또한 중공사막 제조 시내부 응고제는 NMP/증류수(1:1) 혼합용액을 사용하였으며 외부 응고제로는 증류수를 사용하였다. 본 연구는 Silica 나노입자의 크기 및 함량이 분리막 구조에 미치는 영향과 그에 따른 특성을 살펴보았다.

It is a well known that concrete is strong for compression and weak for tension. For reinforcing the weakness and improving the performance about concrete, various methods are used. Fiber reinforced concrete that is one of them has been investigated in this study. The function of fiber in concrete is to improve the stress strain relation and toughness, crack control. It’s applied from normal strength concrete to ultra-high performance concrete. But it is essential to disperse fiber uniformly and to prevent aggregation of fiber in concrete, in order that fiber reinforced concrete show the sufficient performance. The various properties of fiber affect the essential properties, for instance, length and diameter of fiber, source, etc. So, this study evaluated the ultra-high performance concrete with mixed in composite fiber.

PURPOSES: This study develops eco-friendly asphalt reinforcement materials applicable to bridge deck pavement. The main purpose is to ensure highly reliable quality applicable to structures and the possibility of practical application. The main target of the study is to develop materials that are environmentally friendly and capable of improving performanceMETHODS: The application of double-reinforcement fiber improves the performance of the road pavement. 1. We use recycled film for application of sheet-typed reinforcement. 2. We use preprocessing fibers to reinforce the properties of composite pavement materials.RESULTS : The developed products may produce materials that fit the purpose of achieving stability and environmental friendliness. Sheettyped reinforcements use more than 50% recycled resin. The most important type of damage to the asphalt layer is deflection (plastic deformation). These products have a very high deflection resistance of not less than 6,000 cycles/mm. In addition, all performance is excellent. Thus, it will be easier to access the field in the future.CONCLUSIONS: Fiber-reinforced asphalt pavement showed excellent performance. Sheet-typed reinforcements containing 50% recycling resin produced good performance in terms of functionality as well as environmental friendliness. Thus, enhancing the field applicability will enhance the usability of the reinforcements.

본 연구에서는 Polyvinylidene Fluoride(PVDF)와 Polyacrylonitrile(PAN)의 중공 사막 표면에 계면중합하여 복합막을 제조하였다. 지지체 중공사 막은 기존에 상 용화된 제품을 사용하였고, Poly(4-styrene sulfonic acid)(PSSA)와 Polyetherimide 의 농도변화, 이온세기의 변화, 코팅시간의 변화에 따라 막을 제조하였다. 제조한 막의 특성평가를 위해 NaCl, MgCl2, CaSO4 100ppm의 공급액을 이용하여 일정 가동압력과 공급유량에서 막의 투과도와 배제율을 측정하였다.

Multiwall carbon nanotubes (MWCNT) with two different (L/D) aspect ratios (7±2 μm/140±30 nm and 0.5–2 μm/8–15 nm) were surface treated using nitric acid (HNO3) and polyethyleneimine (PEI) prior to their deposition on carbon fibers (CF). Before the hierarchical reinforcement with CF-MWCNT, the CFs were treated with 3-glycidoxypropyltrimethoxysilane, a coupling agent (Z6040) and with poly(amidoamine) (PAMAM) a dendrimer containing an ethylenediamine core and amine surface groups. The MWCNT were deposited on the CF using two methods, by electrostatic attraction and by chemical reactions. The changes in the CF surface morphology after the MWCNT deposition were analyzed using SEM, which revealed a higher density and uniform coverage for the PAMAM-treated CF and the short MWCNTs. The interfacial adhesion of the composite materials was evaluated using the single fiber fragmentation technique. The results indicated an improvement in the interfacial shear strength with the addition of the short-MWCNTs treated with acid solutions and grafted onto the surface of the CF fiber using electrostatic attraction.

The pultruded fiber reinforced polymer plastic (PFRP) is one of the most actively studied composite materials for the structural member in construction industries. In domestic design process, the PFRP member is designed as an isotropic material having only longitudinal material properties for simplicity, because it is too complex to consider orthotrophy of PFRP perfectly. In this study, three cases of buckling analysis of PFRP plate is conducted theoretically and numerically. First, the PFRP plate is considered as an orthotropic material. Second, the PFRP plate is considered as an isotropic plate having only longitudinal material properties. Third, the PFRP plate is considered as an isotropic plate having geometric mean of longitudinal and transverse material properties. As a result of buckling analysis, a buckling strength of PFRP plate as an isotropic plate having only longitudinal material properties is about 2.21 times larger than that of PFRP plate analyzed as an orthotropic plate. On the other hand, a buckling strength of PFRP plate as an isotropic plate having geometric mean material properties is about 1.19 times larger than that of PFRP plate analyzed as an orthotropic plate. In conclusion, the safety factor of 3 used in domestic design process of PFRP member is no longer applicable due to overestimation of buckling strength of PFRP member which leads to nonconservative design.

증류에 의한 올레핀/파라핀 분리는 끓는점이 유사하여 에너지 소모가 높기 때문에, 분리막을 이용한 연구가 많이 진행 중이다. 특히 CMS 분리막은 sieving separation에 의한 투과/분리 성능이 우수하다. 따라서 본 연구에서는 중공사형 α-alumina 지지체에 γ-alumina 중간층을 형성한 후 Matrimid로 코팅하여 열분해함으로써 높은 기계적 강도와 충진 밀도를 갖는 중공사형 CMS 복합막을 제조하였다. 제조된 CMS 분리막은 20 - 35 GPU 프로필렌 투과도와 10 이상의 프로필렌/프로판 분리도를 보였다. 이 연구는 2014년 정부(미래창조과학부)의 재원으로 국가과학 기술연구회 융합연구단 사업(No. CRC-14-01-KRICT)의 지원을 받아 수행된 연구입니다.

본 연구에서는 다공성 PAN(Polyacrylonitrile) 중공사 분리막을 지지체로 이용하여 계면중합반응을 통해 나노여과막을 제조하였다. 지지체로는 PAN을 사용하였으며 수용상으로는 피페라진으로 중공사 분리막 내부에 코팅한 후 유기상인 TMC와 반응하여 계면중합이 일어나도록 진행하였다. 지지체로 사용된 UF 중공사 분리막은 분획분자량 10,000, 30,000, 100,000Da를 각각 사용하였으며 피페라진(Piperazine) 농도를 0.1%, 02%, 0.3%, TMC(Trimesoyl Chloride)의 농도를 0.05%, 0.1%, 0.2%로 변화시켜 제조 하여 5bar에서의 수투과도(LMH)와 MgSO4 2000ppm, Na2SO4 2000ppm, NaCl 500ppm 수용액으로부터 염배제율(Rejection, %)을 확인하였다.

A salinity gradient power (SGP) system holds a great potential to generate continuous and clean electricity for 24 hours. Recently, incorporating with seawater reverse osmosis, SGP has been recognized as a alternative to solve the brine issue as well as energy saving. For commercialization, many scientists would sympathize that one of main hurdles is the limited performance of each membrane to extract the high power. In case of pressure retarded osmosis (PRO) closer to commercialization, the membrane must have the high water permeability and salt rejection. There are two type of modules; hollow fiber membranes and spiral type. Toray Chem. (Korea) already shows that 4th generation PRO module, but there is no still large size PRO hollow fiber modules. Therefore, this study presents 2 and 3 inch size of PRO hollow fiber membrane prepared by inside interfacial polymerization techniques.

Isroaniso matrix precursor synthesized from commercially available petroleum pitch was stabilized in air. The influence of oxygen mass gain during stabilization on the yield of matrix precursor was studied. Additionally, the influence of pressure on the yield of the stabilized matrix precursor in a real system was studied. The fourier transform infrared spectrometry (FTIR), thermogravimetric analysis (TGA), yield, yield rate, and yield impact were used to check the effect of stabilization and pressure on the yield of the matrix precursor and the end properties of the composite thereafter. The results showed that the yield increased with stabilization duration up to 20 h whereas it decreased for stabilization duration beyond 20 h. Further results showed that the stabilized matrix precursor for a duration of 5 h could withstand almost two-fold greater hot-pressing pressure without resulting in exudation as compared to that of a 1 h stabilized matrix precursor. The enhanced hot-pressing pressure significantly improved the yield of the matrix precursor. As a consequence, the densification and mechanical properties were increased significantly. Further, the matrix precursor stabilized for a duration of 20 h or more failed to provide proper and uniform binding of the reinforcement.

This study performed an inverse detection of fiber stiffness degradation that occurs due to damages in free vibrating composite structures. Five unknown parameters are considered to determine the fiber stiffness which is a modified form of the bivariate Gaussian distribution function. The proposed approach is more feasible than the conventional element-based damage detection method from the computational efficiency because a finite element analysis coupled with a genetic algorithm using a small number of unknown parameters is performed. The numerical examples show that the proposed technique is a feasible and practical method, which can prove the location of a damaged region as well as inspect the distribution of deteriorated fiber stiffness although there is a small difference in dynamic characteristics between damaged and undamaged structures.

본 연구에서는 P E I 중공사막 표면에 고무상 고분자인 PDMS를 코팅한 모듈을 이용해 물-Butanol 혼합액의 분리특성을 향상시키는데 중점을 두었다. 먼저 A사에서 개발한 막 면적 890㎠ 모듈을 실험실 테스트 규모로 온도를 변화시키면서 농도 1wt.%의 1-Butanol - Water 혼합액에 대하여 투과증발 실험을 실시하였다. 반응온도 30℃에서 투과도는 58.6g/㎡hr을 나타내었고, 선택도는 9.2%를 나타내었다. 반응온도 40℃에서 투과도는 109.5g/㎡hr을 나타내었고, 선택도는 5.6%를 나타내었다. 반응온도 50℃에서 투과도는 206.9g/㎡hr을 나타내었고, 선택도는 3.0%를 나타내었다. 같은 방법으로 A사에서 개발한 막 면적 1㎡의 모듈을 파일롯 테스트에 적용하여 실험하여 본 결과 비슷한 경향을 보였다.

Impact damages induced by a low-velocity impact load on carbon fiber reinforced polymer (CFRP) composite plates fabricated with various stacking sequences were studied experimentally. The impact responses of the CFRP composite plates were significantly affected by the laminate stacking sequences. Three types of specimens, specifically quasi-isotropic, unidirectional, and cross-ply, were tested by a constant impact carrying the same impact energy level. An impact load of 3.44 kg, corresponding to 23.62 J, was applied to the center of each plate supported at the boundaries. The unidirectional composite plate showed the worst impact resistance and broke completely into two parts; this was followed by the quasi-isotropic lay-up plate that was perforated by the impact. The cross-ply composite plate exhibited the best resistance to the low-velocity impact load; in this case, the impactor bounced back. Impact parameters such as the peak impact force and absorbed energy were evaluated and compared for the impact resistant characterization of the composites made by different stacking sequences.

Shear wall systems behave as individual wall because of openings like window and elevator cage. When coupling beams are installed in shear walls, they will have high strength and stiffness so that be less damaged by lateral loads like earthquake. However, coupling beam is difficult construction method. And arranging reinforcement of slender coupling beams are especially hard. It is because the details of coupling beam provided by ACI 318 are complex. In this paper, experiments were conducted using coupling beams with 3.5 aspect ratio to improve the details of slender coupling beams provided by ACI 318. Two specimens were proposed for this study. One specimen applied with bundled diagonally reinforcement only. Another specimen applied both bundled diagonally reinforcement and High-Performance Fiber Reinforced Cementitious Composite (HPFRCC) so that coupling beams have half of transverse reinforcement. All specimen were compared with a coupling beam designed according to ACI 318 and were evaluated with hysteretic behaviors. Test results showed that the performance of two specimen suggested in this study were similar to that of coupling beam designed according to current criteria. And it was considered that simplification of the details of reinforcement would be available if transverse reinforcement was reduced by using bundled diagonally reinforcement and HPFRCC.

The prime objective of this research was to study the influence of hot-pressing pressure and matrix-to-reinforcement ratio on the densification of short-carbon-fiber-reinforced, randomly oriented carbon/carbon-composite. Secondary objectives included determination of the physical and mechanical properties of the resulting composite. The ‘hybrid carbon-fiberreinforced mesophase-pitch-derived carbon-matrix’ composite was fabricated by hot pressing. During hot pressing, pressure was varied from 5 to 20 MPa, and reinforcement wt% from 30 to 70. Densification of all the compacts was carried at low impregnation pressure with phenolic resin. The effect of the impregnation cycles was determined using measurements of microstructure and density. The results showed that effective densification strongly depended on the hot-pressing pressure and reinforcement wt%. Furthermore, results showed that compacts processed at lower hot-pressing pressure, and at higher reinforcement wt%, gained density gradually during three densification cycles and showed the symptoms of further gains with additional densification cycles. In contrast, samples that were hot-pressed at moderate pressure and at moderate reinforcement wt%, achieved maximum density within three densification cycles. Furthermore, examination of microstructure revealed the formation of cracks in samples processed at lower pressure and with low reinforcement wt%.