검색결과

검색조건
좁혀보기
검색필터
결과 내 재검색

간행물

    분야

      발행연도

      -

        검색결과 374

        41.
        2021.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        This study explores reducing the oxygen content of a commercial Ti-48Al-2Cr-2Nb powder to less than 400 ppm by deoxidation in the solid state (DOSS) using Ca vapor, and investigates the effect of Ca vapor on the surface chemical state. As the deoxidation temperature increases, the oxygen concentration of the Ti-48Al-2Cr-2Nb powder decreases, achieving a low value of 745 ppm at 1100oC. When the deoxidation time is increased to 2 h, the oxygen concentration decreases to 320pp m at 1100oC, and the oxygen reduction rate is approximately 78% compared to that of the raw material. The deoxidized Ti-48Al-2Cr-2nb powder maintains a spherical shape, but the surface shape changes slightly owing to the reaction of Ca and Al. The oxidation state of Ti and Al on the surface of the Ti-48Al-2Cr-2Nb powder corresponds to a mixture of TiO2 and Al2O3. As a result, the peaks of metallic Ti and Ti suboxide intensify as TiO2 and Al2O3 in the surface oxide layer are reduced by Ca vapor deposition
        4,000원
        42.
        2020.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The oxygen-rich activated carbon (AC) was facilely developed using petroleum coke as a raw material by KOH activation under the rapid heating rate. The porosity and surface chemistry of ACs prepared under different heating rates were characterized and their adsorption properties for methylene blue (MB) were investigated. The results showed that the AC5 prepared under the heating rate of 5 °C min−1 had the highest surface area compared with the AC10, AC15 or AC20, while the AC20 prepared under the heating rate of 20 °C min−1 consisted of the highest oxygen content and most –OH functional group compares with the other ACs. These indicated that rapid heating rate was against the formation of more developed porosity, however, it was beneficial to producing more oxygen functional groups. As to MB adsorption, AC15 exhibited the maximum adsorption capacity for MB of 884 mg g−1 due to high surface area of 2803 m2 g−1 and high oxygen content of 23.27%. Moreover, despite the fact that AC20 had much lower surface area than the AC5, the AC20 showed higher MB adsorption capacity than the AC5. This was because the AC20 has the highest content of –OH, which was a positive impetus for MB adsorption. Therefore, rapid heating rate was an effective and simple approach to preparing the oxygen-rich ACs for improving the adsorption capacity of MB.
        4,000원
        43.
        2020.11 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Mass mortality of mariculture fish due to high summer temperatures is a major issue in the mariculture industry in many coastal waters of Korea, yet measures to mitigate the impact are generally limited. We injected a micro-bubble of liquefied oxygen into the bottom of rockfish cages (about 6-8 m deep) in order to maximize the dispersal of micro-bubbled seawater and reduce fish mortality. The injection of low-temperature oxygen in micro-bubbles lowered the water temperature at the injection area by as much as 1℃ and increased dissolved oxygen concentration by 0.5 ppm. In early August, following a week with persistent high water temperature (above 28.5℃), there was an increase in fish mortality despite the micro-bubble system, which resulted in approximately 7% death of the total introduced fish population. However, this mortality appeared to be much lower than mortality reported in a neighboring mariculture facility (approximately 50% mortality). We also estimated the volume that can be recirculated with pumped seawater using a micro-bubble system. We suggest that this approach of injecting liquefied oxygen through a micro-bubble system may reduce fish mortality during high temperature periods.
        4,300원
        44.
        2020.10 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Oxygen evolution reaction (OER) is an essential step at an anode in electrochemical water-splitting process and requires efficient electrocatalysts to reduce overpotentials. Although precious metal-based materials, such as RuO2, IrO2 and their hybrids with other components, performed excellently as OER electrocatalysts, their high cost has limited practical applications. Consequently, earth-abundant metal components including Fe, Co, and Ni have been investigated as alternatives. In this work, the hybridization of Ni-containing species with conductive carbon-based materials was used to prevent aggregation of active species and improve electrochemical catalytic performance. A new hybrid material composed of NiO nanoparticles and N-doped carbon materials was prepared. The NiO particles with a narrow size distribution were well dispersed on the surface of carbon-based materials. The hybrid showed improved electrocatalytic performance for OER than single components of NiO and N-doped carbon materials.
        4,000원
        46.
        2020.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        본 연구에서는 인공지능기법을 이용하여 진동만의 용존산소량 예측을 하였다. 관측자료에 존재하는 결측 구간을 보간하기 위해 양방향재귀신경망(BRITS, Bidirectional Recurrent Imputation for Time Series) 딥러닝 알고리즘을 이용하였고, 대표적 시계열 예측 선형모델인 ARIMA(Auto-Regressive Integrated Moving Average)과 비선형모델 중 가장 많이 이용되고 있는 LSTM(Long Short-Term Memory) 모델을 이용 하여 진동만의 용존산소량을 예측하고 그 성능을 평가했다. 결측 구간 보정 실험은 표층에서 높은 정확도로 보정이 가능했으나, 저층에서는 그 정확도가 낮았으며, 중층에서는 실험조건에 따라 정확도가 불안정하게 나타났다. 실험조건에 따라 정확도가 불안정하게 나타났다. 결과로부터 LSTM 모델이 중층과 저층에서 ARIMA 모델보다 우세한 정확도를 보였으나, 표층에서는 ARIMA모델의 정확도가 약간 높은 것으로 나타났다.
        4,000원
        47.
        2020.05 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        The design and fabrication of catalysts with low-cost and high electrocatalytic activity for the oxygen evolution reaction (OER) have remained challenging because of the sluggish kinetics of this reaction. The key to the pursuit of efficient electrocatalysts is to design them with high surface area and more active sites. In this work, we have successfully synthesized a highly stable and active NiCo2S4 nanowire array on a Ni-foam substrate (NiCo2S4 NW/NF) via a two-step hydrothermal synthesis approach. This NiCo2S4 NW/NF exhibits overpotential as low as 275 mV, delivering a current density of 20 mA cm-2 (versus reversible hydrogen electrode) with a low Tafel slope of 89 mV dec-1 and superior long-term stability for 20 h in 1M KOH electrolyte. The outstanding performance is ascribed to the inherent activity of the binder-free deposited, vertically aligned nanowire structure, which provides a large number of electrochemically active surface sites, accelerating electron transfer, and simultaneously enhancing the diffusion of electrolyte.
        4,000원
        48.
        2019.10 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Amine-functionalized graphene was synthesized via a one-step solvothermal method and used as a metal-free cathode for non-aqueous lithium–oxygen batteries. The material delivered an outstanding specific capacity of 19,789 mAh/g at a current density of 200 mA/g as well as better cycling stability than graphene without the amine functional group. This improvement was attributed to the electron-donating effect of the amine groups and appropriate mesopore volume, which can promote the penetration of oxygen, electrons, and lithium ions, as well as accommodate more discharge products, Li2O2 in Li–O2 batteries. Amine-functionalized graphene has an amine functional group on the carbon surface, which improves the electrical conductivity of carbon and provides electrochemical active sites for oxygen absorption reactions.
        4,000원
        49.
        2019.10 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In this study, the formation, microstructure, and wear properties of Colmonoy 88 (Ni-17W-15Cr-3B-4Si wt.%) + Stellite 1 (Co-32Cr-17W wt.%) coating layers fabricated by high-velocity oxygen fuel (HVOF) spraying are investigated. Colmonoy 88 and Stellite 1 powders were mixed at a ratio of 1:0 and 5:5 vol.%. HVOF sprayed selffluxing composite coating layers were fabricated using the mixed powder feedstocks. The microstructures and wear properties of the composite coating layers are controlled via a high-frequency heat treatment. The two coating layers are composed of γ-Ni, Ni3B, W2B, and Cr23C6 phases. Co peaks are detected after the addition of Stellite 1 powder. Moreover, the WCrB2 hard phase is detected in all coating layers after the high-frequency heat treatment. Porosities were changed from 0.44% (Colmonoy 88) to 3.89% (Colmonoy 88 + ST#1) as the content of Stellite 1 powder increased. And porosity is denoted as 0.3% or less by inducing high-frequency heat treatment. The wear results confirm that the wear property significantly improves after the high-frequency heat treatment, because of the presence of wellcontrolled defects in the coating layers. The wear surfaces of the coated layers are observed and a wear mechanism for the Ni-based self-fluxing composite coating layers is proposed.
        4,200원
        50.
        2019.10 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In order to determine the location of average concentration and distribution status of dissolved oxygen in the rectangular aeration tank of the sewage treatment plant was analyzed and the difference of dissolved oxygen concentration was remarkable at each location. Compared with the computational fluid dynamics analysis, it was found that the results were consistent with the measurement results by showing the difference of dissolved oxygen concentration between the locations. Based on the measured data, the representative location of dissolved oxygen in aeration tank was selected by using statistical analysis method and the representative location was expressed in three-dimensional coordinates(LWH : 25%, 50%, 33%) from flow direction and left wall. Also the difference between the dissolved oxygen concentration at the actual measurement location and the average concentration value of the entire aeration tank was founded, and the equations for calibrating the automatic measurement data considering the actual measurement location were calculated.
        4,000원
        53.
        2019.07 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        ZnO thin-films are grown on a p-Si(111) substrate by RF sputtering. The effects of growth temperature and O2 mixture ratio on the ZnO films are investigated by scanning electron microscopy (SEM), X-ray diffraction (XRD), and roomtemperature photoluminescence (PL) measurements. All the grown ZnO thin films show a strong preferred orientation along the c-axis, with an intense ultraviolet emission centered at 377 nm. However, when O2 is mixed with the sputtering gas, the half width at half maximum (FWHM) of the XRD peak increases and the deep-level defect-related emission PL band becomes pronounced. In addition, an n-ZnO/p-Si heterojunction diode is fabricated by photolithographic processes and characterized using its current-voltage (I-V) characteristic curve and photoresponsivity. The fabricated n-ZnO/p-Si heterojunction diode exhibits typical rectifying I-V characteristics, with turn-on voltage of about 1.1 V and ideality factor of 1.7. The ratio of current density at ± 3 V of the reverse and forward bias voltage is about 5.8 × 103, which demonstrates the switching performance of the fabricated diode. The photoresponse of the diode under illumination of chopped with 40 Hz white light source shows fast response time and recovery time of 0.5 msec and 0.4 msec, respectively.
        4,000원
        54.
        2019.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        High-level heteroatom, N and S, dual-doped graphene with an improved mesoporous structure was fabricated via facile in situ carbonization and used as metal-free cathode for non-aqueous lithium oxygen batteries. The prepared cathode delivered an ultrahigh specific capacity of 22,252 mAh/g at a current density of 200 mA/g as well as better cycling reversibility because of the larger and copious mesopores, which can promote the penetration of oxygen, electrons, and lithium ions and the ability to accommodate more discharge products, e.g., Li2O2, in Li–O2 batteries. The material had a high level of heteroatom co-doping in the carbon lattice, which enhanced the electrical conductivity and served as active sites for the oxygen reduction reaction.
        4,000원
        55.
        2019.06 KCI 등재 구독 인증기관 무료, 개인회원 유료
        To prepare activated carbon with a high specific surface area, oxygen functional groups (OFGs) that can serve as useful electron donors during KOH activation were treated with nitric acid and incorporated into activated carbon. OFGs are incorporated differently according to the surface characteristics of starting materials. Up to 22.46% OFGs are incorporated into wood-based activated carbons (WACs), the C=O, COOH contents was 1.90, 17.05%, respectively. Whereas up to 12.82% OFGs are incorporated into coconut shell-based activated carbons, the C=O, COOH contents was 4.12, 6.15%, respectively. The OFGs used for increasing the specific surface area are the carbonyl group, and as the content of the functional group increases, the carbonyl group spreads to the carboxyl group. The specific surface area of activated carbons increased by 10–68% with an increase in the carbonyl group up to 6% (maximum point of carbonyl group). On the other hand, the specific surface area for WACs increased when the carboxyl group was 10% or below, but decreased by 6–15% when it increased to 10% or excess.
        4,000원
        56.
        2019.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        This paper presents a literature review on the active technologies to regulate the levels of carbon dioxide and oxygen in Kimchi packaging. In this study, laser-etched pouches and O2 scavengers were used for Kimchi packaging, and the efficiency of each packaging technique to regulate the CO2 and O2 levels inside Kimchi packages was investigated. When Kimchi was packaged with a laser-etched pouch, the CO2 concentration in the sample with a high gas transmission rate was less than that in other pouches (p<0.05), and a low CO2 level had little effect on the expansion of the package volume. Kimchi treated with an O2 absorber exhibited a significantly lower (p<0.05) O2 concentration inside the packages relative to the control. A low O2 concentration inside the Kimchi package effectively inhibited the growth of total aerobic bacteria and lactic acid bacteria, as well as yeasts and molds on Kimchi. These results suggest that O2 absorbers have a positive effect on the microbial quality of Kimchi. Therefore, packaging in a laser-etched pouch and the use of an O2 scavenger could provide a novel packaging material for regulating the CO2 and O2 levels during Kimchi packaging.
        4,000원
        57.
        2019.04 구독 인증기관·개인회원 무료
        The Ryanodine Receptor in wild type Drosophila melanogaster has an amino acid substitution which is known to cause Chlorantraniliprole resistance in Pluteall xylostella. Even though we have reported that two Chlorantraniliprole resistant Drosophila strains have elevated total esterase activities, our report does not fully explain the significantly increased resistant ratios in two Chlorantraniliprole resistant Drosophila strains. Thus, we further analyzed alteration of reactive oxygen species and mitochondria activities in two Chlorantraniliprole resistant Drosophila strains. Our result suggested that Chlorantraniliprole resistance development in Drosophila requires alteration of various signal transduction pathways.
        58.
        2019.03 KCI 등재 구독 인증기관 무료, 개인회원 유료
        스트레스는 자율신경계 반응의 변화를 수반하며, 특히 심박변이도 지표는 스트레스에 의한 자율신경계의 활동을 반영하는 양적 지표로 사용된다. 본 연구에서는 스트레스 완화를 위한 산소와 색채 조명의 복합 자극이 제시되는 동안 자율신경계 반응의 변화를 확인하였다. 42명의 실험참가자는 지난 2주 동안 경험한 스트레스에 대한 증상들을 스트레스 반응 척도에 평가하였다. 스트레스 평가 후, 실험참가자는 복합 자극을 제시받았고, 자극 제시 전과 후, 그리고 자극이 제시되는 동안 심전도 신호가 기록되었다. 자극 조건은 30% 농도의 산소와 백색 조명, 산소와 주황색 조명과 산소와 파란색 조명의 조합의 세 가지로 구성되었다. 심박률(HR), R-R간격의 표준편차(SDNN), 연속한 R-R 간격 차이 값의 평균제곱근(RMSSD)과 심박변이도의 저주파 성분(LF), 고주파 성분(HF), 그리고 LF와 HF의 비율을 심박변이도 지표로 추출하였다. 이들 지표는 자극 제시 전과 후의 평균을 비교하는데 활용되었다. 결과는 자극 조건이 제시되고 난 후, HR과 LF/HF ratio의 유의한 감소를 보여주었다. 특히, 산소와 파란색 조명이 제시된 조건에서 다른 두 조건보다 유의하게 큰 RMSSD와 HF의 증가 및 LF/HF ratio의 감소가 나타났다. 이는 30% 농도의 산소와 파란색 조명의 조건이 부교감신경 의 활성화에 의한 자율신경의 균형을 유발하여 스트레스 이완에 가장 효과적임을 보여주었다.
        4,000원
        59.
        2019.02 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        Transition metal oxide is widely used as a water electrolysis catalyst to substitute for a noble metal catalyst such as IrO2 and RuO2. In this study, the sol-gel method is used to synthesize the CuxCo3-xO4 catalyst for the oxygen evolution reaction (OER),. The CuxCo3-xO4 is synthesized at various calcination temperatures from 250 ℃ to 400 ℃ for 4 h. The CuxCo3- xO4 synthesized at 300 ℃ has a perfect spinel structure without residues of the precursor and secondary phases, such as CuO. The particle size of CuxCo3-xO4 increases with an increase in calcination temperature. Amongst all the samples studied, CuxCo3- xO4, which is synthesized at 300?, has the highest activity for the OER. Its onset potential for the OER is 370 mV and the overpotential at 10 mA/cm2 is 438 mV. The tafel slope of CuxCo3-xO4 synthesized at 300 ℃ has a low value of 58 mV/dec. These results are mainly explained by the increase in the available active surface area of the CuxCo3-xO4 catalyst.
        4,000원
        60.
        2018.12 구독 인증기관 무료, 개인회원 유료
        Reactive oxygen species (ROS) and nitrogen species (RNS) are involved in cellular signaling processes as a cause of oxidative stress. According to recent studies, ROS and RNS are important signaling molecules involved in pain transmission through spinal mechanisms. In this study, a patch clamp recording was used in spinal slices of rats to investigate the action mechanisms of O2 ⦁- and NO on the excitability of substantia gelatinosa (SG) neuron. The application of xanthine and xanthine oxidase (X/XO) compound, a ROS donor, induced inward currents and increased the frequency of spontaneous excitatory postsynaptic currents (sEPSC) in slice preparation. The application of S-nitroso-N-acetyl-DLpenicillamine (SNAP), a RNS donor, also induced inward currents and increased the frequency of sEPSC. In a single cell preparation, X/XO and SNAP had no effect on the inward currents, revealing the involvement of presynaptic action. X/XO and SNAP induced a membrane depolarization in current clamp conditions which was significantly decreased by the addition of thapsigargin to an external calcium free solution for blocking synaptic transmission. Furthermore, X/XO and SNAP increased the frequency of action potentials evoked by depolarizing current pulses, suggesting the involvement of postsynaptic action. According to these results, it was estblished that elevated ROS and RNS in the spinal cord can sensitize the dorsal horn neurons via pre- and postsynaptic mechanisms. Therefore, ROS and RNS play similar roles in the regulation of the membrane excitability of SG neurons.
        4,000원
        1 2 3 4 5