회전익 항공기 중 군에서 운용하는 기동헬기는 전장상황에서 운용되기 때문에 연료셀 피탄 상황에 직면할 가능성이 높다. 연료셀 피탄에 따른 내부압력 증가로 내부폭발이나 화재가 발생할 수 있으며, 이는 승무원의 생존 가능성에 치명적인 영향을 주게 된다. 따라서, 승무원의 생존성을 극대화하기 위해서는 연료셀이 직면 가능한 극한 상황을 예측하여 설계에 반영해야 한다. 항공기 연료셀 설계시 고려해야 하는 데이타는 피탄에 의한 연료셀 내부압력, 수압램 영향에 의한 연료셀 자체 및 금속피팅부 응력, 탄환의 운동에너지 등이 포함될 수 있다. 이러한 설계 데이터 확보를 위해서는 실물 시험을 수행하는 것이 가장 바람직하지만, 시간과 비용의 부담과 더불어 시험실패와 같은 시행착오 위험성으로 많은 제약이 따른다. 따라서, 사전에 다양한 설계 데이터 예측과 시행착오의 최소화를 위해서는 피탄 상황에 대한 수치해석이 필요하다. 본 연구에서는 입자법을 사용하여 연료셀 피탄 조건에 대한 유체-구조 연성 수치해석을 수행하였다. 수치해석은 전용 충돌해석 프로그램인 LS-DYNA를 사용하였고, 결과로 얻어진 탄의 거동과 에너지, 연료셀 내부압력과 등가응력의 평가를 통해 연료셀 설계와 관련한 데이터 확보 가능성을 타진하였다.
A numerical analysis was performed to study PEMFC performance characteristics depending on the flow direction of cathode reactant gas, cathode relative humidity, and porosity of gas diffusion layer. As cathode relative humidity decreases and porosity increases, current density increases due to better diffusion of reactant gas to cathode surface. As current density increases, power density increases initially and then decreases with its maximum located around current density value of 2.2 Amperes per square centimeter. From the analysis of current density distribution inside membrane, the counter-flow cases show more uniform profile across the membrane than the co-flow cases due to more uniform reactant gas supply.
Microstructural and mechanical properties of Ni-YSZ fabricated using SPS processing have been investigated at various sintering temperatures. Our study shows samples to be applied as a SOFC anode have the proper porosity of 40% and high hardness when processed at 1100ºC. These results are comparable to the values obtained at 100- 200ºC higher sintering temperature reported by others. This result is important because when the fabrication processes are performed above 1100ºC, the mechanical property starts to decrease drastically. This is caused by the fast grain coarsening at the higher temperature, which initiates a mismatch between thermal expansion coefficients of Ni and YSZ and induces cracks as well.
항공기 연료셀은 추락 상황에서 승무원의 생존성과 직결되는 중요 구성품으로 회전익 항공기에 적용되고 있는 내충격성 연료셀은 추락시 승무원의 생존성 향상에 큰 역할을 하고 있다. 미육군은 항공기가 처할수 있는 다양한 상황에서 연료셀이제 기능을 발휘할 수 있도록 1960년대 초부터 MIL-DTL-27422 이라는 연료셀 개발규격을 제정하여 현재까지 적용해 오고있다. 해당 개발규격에 규정된 시험 중에서 충돌충격시험은 연료셀의 내충격 성능을 검증하는 시험으로써, 해당 시험을 통과하는 연료셀은 생존가능 충돌환경에서 화재가 발생하지 않아 승무원의 생존성이 대폭 향상될 수 있음을 의미한다. 그러나 충돌충격시험은 작용하는 하중 수준이 너무 높기 때문에 실패 위험성이 가장 큰 시험이기도 하다. 연료셀이 해당 시험을 통과하지 못하는 경우에는 재시험을 위한 비용과 준비기간이 상당히 소요되어 항공기 개발일정에 심각한 지장을 초래할 가능성도 높다. 따라서, 연료셀 설계 초기부터 내충격성능 만족여부에 대한 예측을 위해 충돌충격시험의 수치해석을 통한 실물시험에서의 실패 가능성을 최소화해야 한다는 필요성이 제기되어 왔다. 본 연구에서는 충돌모사 프로그램인 LS-DYNA에서 지원하는 유체-구조 연성해석 방법인 SPH 방법을 사용하여 연료셀 충돌충격시험 수치 모사를 수행하였다. 수치해석 조건으로 MIL-DTL-27422에서 요구하는 시험조건을 고려하였고, 실물 연료셀의 시편시험을 통해 확보한 물성데이타를 해석에 반영하였다. 그 결과로 연료셀 자체의 응력수준을 평가하고 취약부위에 대한 고찰을 수행하였다.
In the segmented-in-series solid-oxide fuel cells (SIS-SOFCs), fabrication techniques which use decalcomania paper have many advantages, i.e., an increased active area of the electrode; better interfacial adhesion property between the anode, electrolyte and cathode; and improved layer thickness uniformity. In this work, a cell-stack was fabricated on porous ceramic flattened tube supports using decalcomania paper, which consists of an anode, electrolyte, and a cathode. The anode layer was 40μm thick, and was porous. The electrolyte layers exhibited a uniform thickness of about 20μm with a dense structure. Interfacial adhesion was improved due to the dense structure. The cathode layers was 30μm thick with porous structure, good adhesion to the electrolyte. The ohmic resistance levels at 800, 750 and 700˚C were measured, showing values of 1.49, 1.58 and 1.65Ω·cm2, respectively. The polarization resistances at 800, 750 and 700˚C were measured to be 1.63, 2.61 and 4.17cm2, respectively. These lower resistance values originated from the excellent interfacial adhesion between the anode, electrolyte and cathode. In a two-cell-stack SOFC, open-circuit voltages(OCVs) of 1.915, 1.942 and 1.957 V and maximum power densities(MPD) of 289.9, 276.1 and 220.4mW/cm2 were measured at 800, 750 and 700˚C, respectively. The proposed fabrication technique using decalcomania paper was shown to be feasible for the easy fabrication of segmented-in-series flattened tube SOFCs.
회전익항공기의 연료셀 내부는 연료보관 및 연료를 엔진으로 공급하기 위한 배관과 구성품들이 배치되어 있다. 특히, 기 동헬기는 전장에서 사용되는 헬기로써, 수 km 고도에서 비행하는 고정익기보다 비행고도가 낮기 때문에 피탄될 가능성이 높다. 따라서, 항공기의 생존성을 극대화하기 위해서는 피탄시 유체내부 상승압력에 의한 내부 구성품들이 받는 영향성을 검토하여 설계되어야 함은 주지의 사실이다. 그러나 내탄시험은 연료셀 자체의 제작비용 및 준비기간이 상당히 소요되고, 실탄 사용에 따른 시험수행의 제약 때문에 수치모사를 통한 관련 데이터의 확보가 필요하다. 이를 위해 본 연구에서는 유 체-구조 수치모사 프로그램인 Autodyn을 이용하여 회전익항공기 연료셀의 내탄 수치모사를 수행하여, 피탄 후 연료셀 내 부에서의 탄 거동을 분석하고 유체내부의 압력과 연료 셀 자체의 등가응력을 평가하였다.
La1-xSrxMnO3(LSM,0≤x≤0.5) powders as the air electrode for solid oxide fuel cell were synthesized by a glycine-nitrate combustion process. The powders were then examined by X-ray diffraction(XRD) and scanning electron microscopy (SEM). The as-formed powders were composed of very fine ash particles linked together in chains. X-ray maps of the LSM powders milled for 1.5 h showed that the metallic elements are homogeneously distributed inside each grain and in the different grains. The powder XRD patterns of the LSM with x< 0.3 showed a rhombohedral phase; the phase changes to the cubic phase at higher compositions(x≥0.3) calcined in air at 1200˚C for 4 h. Also, the SEM micrographs showed that the average grain size decreases as Sr content increases. Composite air electrodes made of 50/50 vol% of the resulting LSM powders and yttria stabilized zirconia(YSZ) powders were prepared by colloidal deposition technique. The electrodes were studied by ac impedance spectroscopy in order to improve the performance of a solid oxide fuel cell(SOFC). Reproducible impedance spectra were confirmed using the improved cell, which consisted of LSM-YSZ/YSZ. The composite electrode of LSM and YSZ was found to yield a lower cathodic resistivity than that of the non-composite one. Also, the addition of YSZ to the La1-xSrxMnO3 (0.1≤x≤0.2) electrode led to a pronounced, large decrease in the cathodic resistivity of the LSM-YSZ composite electrodes.
Two types of Pt nanoparticle electrocatalysts were composited on Pt nanowires by a combination of an electrospinning method and an impregnation method with NaBH4 as a reducing agent. The structural properties and electrocatalytic activities for methanol electro-oxidation in direct methanol fuel cells were investigated by means of scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and cyclic voltammetry. In particular, SEM, HRTEM, XRD, and XPS results indicate that the metallic Pt nanoparticles with polycrystalline property are uniformly decorated on the electro-spun Pt nanowires. In order to investigate the catalytic activity of the Pt nanoparticles decorated on the electro-spun Pt nanowires, two types of 20 wt% Pt nanoparticles and 40 wt% Pt nanoparticles decorated on the electro-spun Pt nanowires were fabricated. In addition, for comparison, single Pt nanowires were fabricated via an electrospinning method without an impregnation method. As a result, the cyclic voltammetry and chronoamperometry results demonstrate that the electrode containing 40 wt% Pt nanoparticles exhibits the best catalytic activity for methanol electro-oxidation and the highest electrochemical stability among the single Pt nanowires, the 20 wt% Pt nanoparticles decorated with Pt nanowires, and the 40 wt% Pt nanoparticles decorated with Pt nanowires studied for use in direct methanol fuel cells.
불소관능기인 perfluorocyclobutane (PFCB)기를 포함하는 후술폰화 poly (arylene ether sulfone) 랜덤 공중합체를 다공성 Polytetrafluoroethylene (PTFE) 막에 함침시켜 새로운 복합막을 제조하였다. 후술폰화 랜덤 공중합체는 trifluorovinyloxy 그룹을 양말단에 포함하는 biphenyl계와 sulfonyl계 단량체로부터 제조되었는데, biphenyl계와 sulfonyl계의 비율을 6 : 4와 4 : 6으로 조절 후 중부가반응 형태의 열중합과 chlorosulfonic acid (CSA)를 이용한 후술폰화 반응을 통하여 얻어졌다. 이렇게 제조된 랜덤 공중합체의 농도를 달리하면서(5~20 wt%) 다공성 PTFE 막에 함침시켜 복합막을 제조하였고, 이온 교환 능력(IEC), 함수율, 이온전도도를 측정하여 강화되지 않은 랜덤공중합체 및 Nafion과 비교하였다. 제조된 단량체 및 고분자의 구조와 순도는 각각 1H-NMR, 19F-NMR와 FT-IR를 통하여 확인하였으며, 제조된 복합막의 형태는 SEM으로 관찰하였다.
연료전지는 석유엔진과 비교하여 높은 전류밀도와 효율성, 그리고 친환경적이기 때문에 21세기 들어 대체 발전시스템으로서 각광받아왔다. 연료전지 시스템에서 고분자 전해질 막은 핵심부품으로써 현재 Nafion막이 연료전지시스템에서 사용 중이지만 높은 제조단가와 고온에서 낮은 전도도를 가지는 단점을 가지고 있다. 그러므로 많은 학자들이 낮은 제조단가, 높은 물리적 특성들을 달성하기 위한 연구를 진행하여 왔으며 연료전지의 상용화와 동시에 고성능의 연료전지의 개발을 위하여 많은 방법들이 개발되어 왔다. 그중, 유무기 복합막은 유기물과 무기물의 물성을 균일하게 조합할 수 있으므로 잠재성을 가지고 있는 제조방법이다. 본고에서는 다양한 무기물이 사용되어 제조된 유무기 복합막의 연구동향에 대하여 조사하였다.
The air blowers for fuel cell electric vehicle usually have big difference between inlet and outlet pressure. When the casing of the air blowers is designed, the stress analysis is required. (Approximately Inlet pressure is 0.5bar and outlet pressure is 2bar.) Gap distance between the casing and the impeller is 0.3mm. Therefore, if the amount of maximum deformation of casing is larger than 0.3mm, impeller crashed the casing. In order to avoid crashing, both the thickness and number of rims are changed and carried out simulations on each cases.
Joining of NiO-YSZ to 316 stainless steel was carried out with B-Ni2 brazing alloy (3 wt% Fe, 4.5 wt% Si, 3.2 wt% B, 7 wt% Cr, Ni-balance, m.p. 971-) to seal the NiO-YSZ anode/316 stainless steel interconnect structure in a SOFC. In the present research, interfacial (chemical) reactions during brazing at the NiO-YSZ/316 stainless steel interconnect were enhanced by the two processing methods, a) addition of an electroless nickel plate to NiO-YSZ as a coating or b) deposition of titanium layer onto NiO-YSZ by magnetron plasma sputtering method, with process variables and procedures optimized during the pre-processing. Brazing was performed in a cold-wall vacuum furnace at . Post-brazing interfacial morphologies between NiO-YSZ and 316 stainless steel were examined by SEM and EDS methods. The results indicate that B-Ni2 brazing filler alloy was fused fully during brazing and continuous interfacial layer formation depended on the method of pre-coating NiO-YSZ. The inter-diffusion of elements was promoted by titanium-deposition: the diffusion reaction thickness of the interfacial area was reduced to less than 5 compared to 100 for electroless nickel-deposited NiO-YSZ cermet.
본 연구는 고내구성을 가진 고분자 전해질 막을 제조하는 것으로 연료전지에 적용하기 위하여 poly(vinyl alcohol)를 주쇄부로 하여 poly(styrene sulfonic acid-co-maleic acid) (PSSA-MA)와 3-(trihydroxysilyl)-1-propanesulfonic acid (THS-PSA)를 polyethylene막에 함침시켜 막을 제조하였다. 제조된 막을 함수율, 접촉각, FT-IR, 수소이온전도도, 탄성계수 등의 측정을 통해 친수성 고분자가 함침된 막의 특성평가를 실시하였다. FT-IR 분석과 접촉각 측정을 통해 PE막에 함친된 막에서 친수성기의 유무를 확인하였다. 수소이온전도도를 측정한 결과 30% THS-PSA의 막이 55℃에서 1.27×10 1S/㎝의 값을 나타내어 우수한 수소이온전도도를 나타내었으며, 탄성계수의 측정을 통해 polyethylene막에 비하여 THS-PSA가 함침된 막의 기계적 강도가 15%까지는 최대 7배까지 향상되어 막의 내구성이 향상되었음을 확인하였다.
기질 고분자인 sulfonated PEEK (sPEEK)와 가교제(cross-linking reagent) 4,4'-ethyldianiline (EdAn), 그래프트제(grafting reagent) 2-phenylethylamine (PEA)을 용매 dimethylacetamide (DMAc)에 녹여 용매증발법을 이용하여 제막하였다. 이민화 반응(imination)과 술폰화(sulfonation) 과정을 거쳐 최종 이온교환막인 cross-linked and grafted sPEEK (CG-sPEEK)막을 제조하였다. FT-IR 분석을 통해 술폰화 및 이민화 반응여부를 확인할 수 있었다. Proton conductivity와 water uptake, volume change를 측정하여 상용화된 Nafion115와 비교함으로써 이온교환막으로서의 활용가능성을 평가하였다. 제조된 CG-sPEEK막의 proton conductivity (0.17 S/cm) 값이 Nafion115 (0.10 S/cm) 보다 우수하게 나타나 이온교환막으로서의 적용가능성을 보여주었다. 다만 높은 water uptake (130%)는 CG-sPEEK의 치수안정성을 위해서 저감시킬 필요가 있다.
Nanosized Pt, Pt-Ru and Pt-CeO2 electrocatalysts supported on acid-treated carbon nanotube (CNT) were synthesized by microwave-assisted heating of polyol process using H2Cl6Pt·6H2O, RuCl3, CeCl3 precursors, respectively, and were characterized by XRD and TEM. And then the electrochemical activity of methanol oxidation for catalyst/CNT nanocomposite electrodes was investigated. The microwave assisted polyol process produced the nano-sized crystalline catalysts particles on CNT. The size of Pt supported on CNT was 7~12 nm but it decreased to 3~5 nm in which 10wt% sodium acetate was added as a stabilizer during the polyol process. This fine Pt catalyst particles resulted in a higher current density for Pt/CNT electrode. It was also found that 10 nm size of PtRu alloys were formed by polyol process and the onset potential decreased with Ru addition. Cyclic voltammetry analysis revealed that the Pt75Ru25/CNT electrode had the highest electrochemical activity owing to a higher ratio of the forward to reverse anodic peak current. And the chronoamperemetry test showed that Pt75Ru25 catalyst had a good catalyst stability. The activity of Pt was also found to be improved with the addition of CeO2.
Ground source heat pumps are clean, energy-efficient and environment-friendly systems. Although the initial cost of ground source heat pump system is higher than that of air source heat pump, it is now widely accepted as an economical system since the installation cost can be returned within an short period of time due to its high efficiency. In the present study, performances of ground source compound hybrid heat pump system applied to a resort building are simulated. The system design and operation process appropriate for the surrounding circumstance guarantee the high benefit of the heat pump system applied to a resort building. If among several renewable energy sources, ground, river, sea, waste water source are chosen as available alternative energies are combined, COP of the system can be increased largely and hybrid heat pump system can reduced the fuel cost.
Different oxidation treatments on CNTs using diluted 4.0 M H2SO4 solution at room temperature and or at 90℃ reflux conditions were investigated to elucidate the physical and chemical changes occurring on the treated CNTs, which might have significant effects on their performance as catalyst supports in PEM fuel cells. Raman spectroscopy, X-ray diffraction and transmission electron microscope analyses were made for the acid treated CNTs to determine the particle size and distribution of the CNT-supported Pt-Ru nanoparticles. These CNT-supported Pt-based nanoparticles were then employed as anode catalysts in PEMFC to investigate their catalytic activity and single-cell performance towards H2 oxidation. Based on PEMFC performance results, refluxed Pt-Ru/CNT catalysts prepared using CNTs treated at 90℃ for 0.5 h as anode have shown better catalytic activity and PEMFC polarization performance than those of the commercially available Pt-Ru/C catalyst from ETEK and other Pt-Ru/CNT catalysts developed using raw CNT, thus demonstrating the importance of acid treatment in improving and optimizing the surface properties of catalyst support.