친수성 및 소수성 나노실리카를 tetraethyl orthosilicate(TEOS)를 커플링제로 사용하여 유리 표면에 거친 스파이크 구조 형성과 반응성 hydroxyl기를 동시에 도입한 후 불소를 함유한 실란으로 2차 코팅처리하여 궁극적으로 발수성 유리 표면 형성의 최적 조건을 확립하는 연구를 수행하였다. 소수 성 나노실리카인 실리카 에어로졸을 이용한 초소수 도막의 형성은 나노실리카 표면에 반응성인 -OH기가 존재하지 않아 내구성이 있는 소수성 도막을 형성할 수 없었다. 이에 반하여 친수성기를 가진 나노 실리카와 가수분해된 TEOS를 포함하는 코팅액 이용하여 유리 표면을 1차 코팅한 후 2차로 trichloro-(1H,1H,2H,2H)perfluorooctylsilane(TPFOS) 용액으로 코팅하여 150o 이상의 수접촉각을 가지는 초소수 표면을 제조하였으며, 1o 이하의 물 슬라이딩각을 보여 초발수성도 동시에 가지고 있었다. 이에 덧붙여 친수성 나노실리카의 함량이 증가할수록 광투과도가 감소하였으며, TPFOS 용액에 의해서도 광투과도가 감소하였다. 코팅된 유리시편의 내구성 50회 문지름까지는 초소수성을 유지하였으나, 200회 문지름에서는 단지 소수성만을 유지하였다. 결론적으로 최적의 코팅액의 조건은 친수성 나노실리카의 함량이 0.3 g인 HP3 코팅액을 2회 코팅한 후 2차로 TPFOS 용액으로 코팅하는 것이었다. 이렇게 제조된 코팅액은 광투과도가 중요한 솔라셀의 표면 처리제로 사용이 가능할 것으로 판단된다.

Glass wool is widely used as a typical soundproofing material because it has superior characteristics as a soundproofing material as well as excellent marketability. However, moisture penetration through condensation and cleaning up causes deterioration of insulation and soundproofing performance. In this study, we evaluate the wettability and sound absorption performance when the metal is deposited on the surface of glass wool. The performance is examined based on parameters such as the angle test, drying speed, the absorbency, the moisture content, the wettability. The wettability data shows that Cu coated glass wool is the best performance compaed to Ti coated one. The sound insulation characteristics are also compared by using the impedance tube. At the low frequency range, there is no difference among the test specimens, however, at the frequency above the 250 Hz range, Cu coating shows 10 % better in th sound asorption. Ti coating has almost same to the existing glasss wool performance. It turns out that metal coating on the glass wool seems to be very promising: the metal deposition reveals strong water repellency and sound absorption performance is equivalent to the existing glass wool.

목적: ITO 박막과 발수 박막의 두께에 따른 안경렌즈 투과율 변화를 관찰하고자 한다. 방법: Electron beam evaporation 와 dipping장비로 ITO 코팅, 발수 코팅, SiO2, ZrO2, 하드 코팅 막 을 제작하고 분광광도계와 ellipsomter를 이용하여 파장에 따른 광학상수를 구했다. 이러한 데이터를 이용 하여 Macleod 프로그램으로 ITO 박막과 발수 박막의 두께에 따른 안경렌즈 투과율의 변화를 관찰하였다. 박막설계는 [air / repellent film / ITO / SiO2-ZrO2-SiO2-ZrO2 / AR coating / hard coating(1.553) / lens(1.56)] 와 같다. 결과: ITO 박막과 발수 박막이 없을 시 최적 투과율은 400nm에서 700nm 까지의 평균 투과율은 약 99.5%이다. 안경렌즈 전 후면에서의 반사율이 비슷하므로 안경렌즈 전체 투과율은 약 99%이다. 발수 박막 의 두께를 고정시키고 ITO 박막의 두께를 증가시키면 가시광선의 단파장 영역의 투과율이 장파장에 비해 많 이 감소된다. ITO 박막을 고정시키고 발수 박막의 두께를 증가시킬 경우 장파장의 투과율이 감소하고 단파 장의 투과율은 발수 박막의 두께가 50nm 까지 감소하다가 그 이후에서는 투과율이 증가한다. 결론: ITO 박막의 두께를 증가시키면 가시광선의 단파장 영역의 투과율이 장파장에 비해 많이 떨어지고, 발수 박막의 두께를 증가시킬 경우 장파장의 투과율이 감소하고 단파장의 투과율은 발수 박막의 두께가 50nm 까지 감소하다가 그 이후에서는 투과율이 증가한다.

본 연구에서는 심한 소음으로 불쾌감을 주는 스포츠웨어용 PTFE 라미네이팅 투습발수 직물 8종을 대상으로 직물 마찰음의 심리음향학적 특성을 고찰하고, 심리음향학적 특성에 영향을 미치는 직물의 기본 특성과 역학적 특성 간의 관계를 파악함으로써, 직물의 심리음향학적 마찰음을 낮출 수 있는 변인을 찾아내고자 하였다. 직물 마찰음 시뮬레이터를 이용하여 녹음한 직물의 소리에서 Zwicker의 파라미터인 심리음향학적 크기(loudness(Z)), 날카로움(sharpness(Z)), 거칠기(roughness(Z)), 그리고 변동강도(fluctuation strength(Z))를 계산한 뒤, 소리특성에 대한 사후검정 결과에 따라 시료를 덜 시끄러운 PTFE 필름 그룹과 더 시끄러운 PTFE 필름 그룹으로 나누어 마찰음의 심리음향학적 특성과 직물의 역학적 특성, 기본특성간의 관계를 고찰하였다. 심리음향학적 특성 중 loudness(Z)만이 시료의 마찰음과 유의한 관계에 있는 것으로 나타났으며, 분석 결과 직물의 기본 특성에서는 layer가 얇고 필라멘트사를 사용한 직물의 마찰음이 덜 시끄럽게 인지되는 것으로 나타났으며, 직물 마찰음의 심리음향학적 크기에 영향을 미치는 주요변수로는 layer로 것으로 나타났다. 마찰음이 작은 PTFE 필름 그룹의 경우 전단 방향으로의 변형이 어려울수록 마찰음이 시끄나타났다. 시끄러운 마찰음을 갖는 PTFE 필름 그룹의 경우 심리음향학적 크기에 영향을 미치는 주요 변수로 전단이력이 설명 변인으로 포함되었다.

The static and dynamic hydrophobicities of the water droplets placed on a hydrophobic surface coated using a fluoroalkylsilanes monolayer with different molecular chain lengths were investigated through direct observation of the actual droplet motion during the sliding process. The surface roughness of both was found to be less than 1 nm. The static contact angles of the coated FAS-3 and FAS-17 were respectively 80˚ and 108˚ at 150˚C, 1 h. The slope of sliding acceleration against the water droplet mass exhibited an inflection point, thus suggesting the switching of the dominant sliding mode from slipping to rolling. While their sliding angles were similar in value, notable differences were exhibited in terms of their sliding behavior. This can be understood as being due to the contribution of the shear stress difference at the interface between the solid surface and water during the sliding process. These results show that the sliding acceleration of the water droplets depends strongly on the balance between gravitational and retentive forces on the hydrophobic surface.

Durable softening water repellents such as PODCW, PDDCW, and PEDCW were prepared by blending cationized polymers, fatty carbamide, waxes, and emulsifiers. The cationized polymers included poly (octadecyl methacrylate-co-2-diethylaminoethyl methacrylate) [PODC], poly (n-dodecyl methacrylate-co-2-diethylaminoethyl methacrylate) [PDDC]and poly (2-ethylhexyl methacrylate-co-2-diethylaminoethyl methacrylate) [PEDC]. After the PET fabrics were treated with these water repellents, water repellency, softness, and durability of the PET fabrics were examined by various methods : water repellency by the hydrostatic pressure and the contact angle methods, softness by crease recovery and tearing strength, and durability by washability, respectively. Rating of water repellency of PET fabrics treated with PODCW was 80+, but those treated with PDDCW and PEDCW were not high enough to be used in industry.

The procedure to prepare an acrylic emulsion water repellents by blending of arcylic copolymer, activated polyethylene, wax, and emulsifiers was published in the previous paper. After the treatment of the prepared water repellents on a cotton fabrics with and without textile finishing resin, washability, contact angle, tearing strength, and crease recovery were tested. As the result, there were remarkable improvements in physical properties. Proper curing temperature of the synthesized water repellents impellents was 150℃ : proper using concentration was 5wt% : sodium acetate was the best catalyst for water repellents among the used, and proper concentration was 1.0wt%.

Durable softening water-repellenting agent such as PODCW, PDDCW and PEDCW were prepared by blending cationized compound such as poly(octadecyl methacrylate-co-2-diethylaminoethyl methacrylate)[PODC], poly(2-dodecyl methacrylate-co-2-diethyl-aminoethyl methacrylate)[PDDC] and poly(2-ethylhexyl methacrylate-co-2-diethyl-aminoethyl methacrylate)[PEDC], and cationized compound of fatty carbamide, of which synthetic methods were reported in the previous paper, waxes, and emulsifiers. The results of physical tests of the P/C blended fabrics treated with PODCW, PDDCW and PEDCW with and without textile finishing resin, showed a remarkable improvement of the physical properties. The prepared water-repellenting agents, PODCW-6 and PDDCW-1, were treated on P/C blended fabrics with and without resin. For any cases, there are a little changes between initial water repellency and repellency after 3 times washing of the fabrics. Therefore, the water-repellenting agents proved to be a durable agents, and initial water 100+ and 90+ point, respectively.

Durable softening water repellents such as PODCWs were prepared by blending cationized compound of poly(octadecyl methacrylate-co-2-diethylaminoethyl methacrylate), of which synthetic methods were reported in the previous paper, activated polythylene, waxes, and emulsifiers. Water repellency of prepared PODCWs was measured by performing water repellent finish to various fabrics, PODCWs showed a good water repellency for P/C blended fabrics and their repelling tendency was in the order of P/C blended fabrics〉cotton fabrics〉nylon taffeta. The initial water repellencies of PODCW-1 and PODCW-2 were 100 and 100- points, respectively, for P/C blended fabrics. And also, PODCW-1 and PODCW-2 were confirmed as durable water repellents with the results of making little difference of water repellency as ±5 point after and before washing.

To prepare a durable softening water repellent, quaternized octadecyl methacrylate-2-diethyl-aminoethyl methacrylate as a mother resin and quaternized 1, 3-dioctadecyl-2, 7-dioxy-6, 8-di(2-hydroxyethyl)-1, 3, 6, 8-tetraazacyclodecane which increase the softening effect and the hydrostatic pressure blended with waxes and their emulsifier in various proportions to give water repellent PADWC. As the results of the measurement of water repellency, washable, tear strength and crease recovery to polyestercotton(P/C) blended fabrics treated with PADWC only or addition of textile finishing resin, the physical properties were increased. There was no significant lowering effect in water repellency when PADWC was treated the antistatic agent by the one-bath method, and the effect of water repellency by the adding the catalyst was studied. PADWC was confirmed as durable water repellent with the results of making little difference of water repellency as ±5 point after and before washing.

Durable softening water repellents for nylon fiber were synthesized, using two compounds: quaternized octadecyl methacrylate-2-diethylaminoethyl methacrylate copolymer as a mother resin of water repellent and quaternized fatty carbamide for improving softness and hydrostatic pressure, of which syntheses were studied in the previous papers. They were blended with waxes and emulsifiers in a variety of ratios and synthesized into water repellent PADWC, and it was nylon taffeta treated with and without textile finishing resin. The synthesized water repellents can be used either or without resin. The optimum curing temperature was 150 to 160℃ and the optimum concentration was 3 to 5wt%. In the independent and conjunct treatment, the water repellency of nylon taffeta samples have no remarkable changes between initial value and that after three times washing, so these prove that the synthesized compounds are durable water repellent. The water repellency of PADWC-3 and -4 were around 90. Also, comparison of crease recovery and tear strength after repelling treatment showed that the synthesized water repellents have a very high softening effect.

In the preparation of acrylic water repellent(EDLWC). quaternized 2-diethylarrunoethylmethacrylate-stearylmethacrylate copolymer (DSACC) and quaternized 1-Iaurovlbis(aminoethyl)-2-dodecylimidazoline(LDDIC) were selected as a basic resin and the improving agent such as softening effect and hydrostatic pressure of the water repellent. EDLWC was prepared by blending waxes and emulsifier for waxes with various ratio to DSACC and LDDIC. As the results of the measurement of water repellency, washable, tear strength and crease recovery to polyester-cotton(P/C) blended fabrics treated with EDLWC only or addition of textile finishing resin, the physical properties were increased. Sodium acetate was the most effective catalyst in the water repellency among the various kinds of catalyst. and the reasonable concentration of the catalyst was 1. 4 wt%. EDLWC was confirmed as durable water repellent with the results of making little difference of water repellency as ±5 point after and before washing. The reaction mechanism between P/C blended fabrics and EDLWC in the presence of catalyst was proposed. And also, the longitudinal view of the P/C blended fabrics treated with water repellent was observed with scanning electron microscope.

The quaternized compound of the copolymer between 2-diethylaminoethyl methacrylate and stearyl methacrylate (DSACC) was chosen as the mother resin for the water repellent of acrylics. The quaternized compound of 1-lauroyl dis (amino ethyl)-2-dodecyl imidazoline (LDDIC) was used to promote softening effect and hydrostatic pressure for the water repellent. The water repellent (EDUWC) obtained from the DSACC and LDDIC blended with waxes and emulsifiers improved the properties such as the water repellency, washable, tear strength and crease recovery when it was treated on the nylon fabrics with and without the resin. The reaction mechanism between the Nylon fiber and EDLWC was examined, and EDLWC was confirmed as the durable water repellent.

콘크리트는 외부로부터 침투하는 열화 인자들의 침투에 의해 철근이 부식하고 구조재료로써의 성능이 저하된다. 발수제를 직접 도포하거나 혼입하는 방법이 연구되고 있고, 본 연구에서는 발수제의 뭉침 및 떠오름을 방지하기 위하여 다공성 재료인 제올라이트를 혼입한 발수콘크리트 개발을 위한 기초연구를 수행하였다. 제올라이트 치환율에 따른 시험체를 제작하였으며, 접촉각 측정결과 치환량과 접촉각의 크기는 비례하여 증가하는 것을 확인하였다.