In this study, non-destructive technologies that can be applied to evaluate the integrity of valve materials, safety against internal pressure caused by corrosion, and the blocking function of large-diameter water valves during operation without requiring specimen collection or manpower entering the inside of the valve were tested to assess the reliability of the technologies and their suitability for field application. The results showed that the condition of the graphite structure inside the valve body can be evaluated directly through the optical microscope in the field without specimen collection for large-diameter water butterfly valves, and the depth of corrosion inside the valve body can be determined by array ultrasound and the tensile strength can be measured by instrumented indentation test. The reliability of each of these non-destructive techniques is high, and they can be widely used to evaluate the condition of steel or cast iron pipes that are significantly smaller in thickness than valves. Evaluation of blocking function of the valves with mixed gas showed that it can be detected even when a very low flow rate of mixed gas passes through the disk along with the water flow. Finally, as a result of evaluating the field applicability of non-destructive technologies for three old butterfly valves installed in the US industrial water pipeline, it was found that it is possible to check the material and determine the suitability of large-diameter water valves without taking samples, and to determine the corrosion state and mechanical strength. In addition, it was possible to evaluate safety through the measurement results, and it is judged that the evaluation of the blocking function using mixed gas will help strengthen preventive response in the event of an accident.

PURPOSES: Spalling is one of the primary problems that lead to the damage of concrete pavements. The purpose of the study is to analyze the impact range of spalling that occurred in an area of concrete pavement by applying a variety of nondestructive and destructive testing methods. METHODS: Spalling of the concrete pavement was categorized into four different sizes, 0 cm, 7.5 cm, 15 cm, and 30 cm. Nondestructive and destructive tests were performed at the point of spalling and 1 m away, respectively, and the obtained results were compared. The nondestructive tests included the electrical resistance test and the ultrasonic velocity test as well as strength tests by Schmidt hammer and concrete tester. The destructive tests included the direct compressive strength test and the chloride content test using field cored specimens. The test results helped in the analysis of the correlation between the current spalling damage condition and the expected damage acceleration. RESULTS: Based on the present study, the repair area and depth of spalling for a partial depth repair was suggested. It was also shown that the size of the spalling is highly correlated with the chloride content and the electrical resistance of the concrete pavement. CONCLUSIONS: The degree of spalling deterioration was found to be highly correlated with the chloride content and electrical resistance of the concrete pavement and based on the results, the extent of repair could be determined more quantitatively.

PURPOSES: This study is to estimate nondestructive strength equation based on probability for bridges using field test data. METHODS: In this study, a series of the field inspection and the test have been performed on 297 existing bridges, in order to evaluate the bridges, based on the test results of the in-depth inspection, and the estimated strengths by means of the nondestructive strength equations are analyzed and compared with results of the core specimen strengths. RESULTS: According to results of analyses, In case of standard design compressive strength of concrete is 18MPa, 21MPa, similar reliability of RILEM equation were 0.89~0.90, but in case of standard design compressive strength of concrete is 35MPa, 40MPa were 0.4~0.56. According to standard design compressive strength of concrete is 40MPa, similar reliability of ultrasonic pulse velocity method equation were 0.56. CONCLUSIONS: RILEM equation had high similar reliability than other equation in case of standard design compressive strength of concrete is 18MPa, 21MPa, but had low similar reliability than other equation in case of standard design compressive strength of concrete is 35MPa, 40MPa. and ultrasonic pulse velocity method equation had low similar reliability than other equation in case of standard design compressive strength of concrete is 40MPa.

Plant physiological indices for Euryale ferox Salisb. an endangered aquatic plant from Gyeongsan Province, were analyzed in this study. The NDVI (Normalized Difference Vegetation Index) was highest at 0.820 in Dongguji and lowest at 0.592 in Dongjaji; the SR (Simple Ratio) index was highest at 10.240 in Dongguji and lowest at 4.312 in Dongjaji; and the PRI (Photochemical Reflectance Index) was highest at 0.039 in Dongguji and lowest at −0.036 in Dongjaji. The CRI1 (Carotenoid Reflectance Index 1) index was in Sahwaji and Waji at 8.881 and 12.988, respectively, and the CRI2 (Carotenoid Reflectance Index 2) index was highest at 7.889 in Sahwaji and lowest at 11.889 in Dongjaji.

Thermographic imaging based non-destructive evaluation proceeds measuring the defect or internal condition of civil structures. To demonstrate the feasibility of the method, the infrared camera system is applied to various specimens. The technique described in this paper may allow us to find their numbers, locations, and the extent of damaged steels from the measurement in the long distance. In addition, a reinforced concrete specimens with different penetration depths is tested using the active thermography method, and to study the influence on the detecting internal rebar in cooled and heated conditions. The experimental results demonstrate that thermographic imaging method is useful for detecting the damage of steel structures and the unknown rebar in the concrete.

PURPOSES: It is theoretically well known all over the world, that porous hot mixed asphalt (HMA) with hydrated Lime improves moisture and rutting resistance, and reduces pothole occurrence frequency, as well as the life cycle cost (LCC). METHODS : Addictive in the two different formations of the liquid anti-stripping Agent and powder Hydrated-Lime was applied in this investigation in order to obtain relatively clear results according to their types and conditions. Firstly, the moisture conditions were set, and applied to the porous HMA mixtures with hydrated lime (anti-stripping agent). Next, it was followed by a non-destructive test with the application of three freeze-thaw cycles, which were individually carried out thrice to compare the results of the dynamic moduli. Lastly, the hydrated lime effect related to moisture sensibility to porous HMA has been verified through the analysis of the modulus results regarding the change rate of dynamic modulus per n-cycle. RESULTS: It is clear from this investigation, that the dynamic modulus is inversely proportional to the change in temperature, as the graph representing the rigidity of the thermorheologically simple (TRS) material showed gradual decline of the dynamic modulus with the increase in temperature. CONCLUSIONS: The porous HMA mixture with the anti-stripping agent (hydrated Lime) has been found to be more moisture resistant to freezing and thawing than the normal porous HMA mixture. It is clear that the hydrated lime helps the HMA mixture to improve its fatigue resistance.

PURPOSES: The dynamic modulus for a specimen can be determined by using either the non-destructed or destructed testing method. The Impact Resonance Testing (IRT) is the one of the non-destructed testing methods. The MTS has proved the source credibility and has the disadvantages which indicate the expensive equipment to operate and need a lot of manpower to manufacture the specimens because of the low repeatability with an experiment. To overcome these shortcomings from MTS, the objective of this paper is to compare the dynamic modulus obtained from IRT with MTS result and prove the source credibility. METHODS: The dynamic modulus obtained from IRT could be determined by using the Resonance Frequency (RF) from the Frequency Response Function (FRF) that derived from the Fourier Transform based on the Frequency Analysis of the Digital Signal Processing (DSP)(S. O. Oyadigi; 1985). The RF values are verified from the Coherence Function (CF). To estimate the error, the Root Mean Squared Error (RMSE) method could be used. RESULTS : The dynamic modulus data obtained from IRT have the maximum error of 8%, and RMSE of 2,000MPa compared to the dynamic modulus measured by the Dynamic Modulus Testing (DMT) of MTS testing machine.. CONCLUSIONS: The IRT testing method needs the prediction model of the dynamic modulus for a Linear Visco-Elastic (LVE) specimen to improve the suitability.

세계는 계속해서 발전해 가고 있다. 따라서 우리나라 또한 비약적인 발전을 이루고 있다. 도심지가 개발 되고, 도로가 계획·건설 됨으로써 불투수 면적은 급속도로 증가하였다. 최근 서울의 불투수 면적은 1962년 7.8%에서 2010년 47.7%로 급증하였다. 심한 곳은 불투수 면적이 90% 이상인 곳도 있다. 불투수 면적이 증가하면서 열섬현상을 심화시키고 강우에 따른 지하수의 유입이 감소되어 지하수는 고갈되어 가고 있다. 시간이 지남에 따라 상황은 지금보다 악화될 것이다. 우리는 이에 따른 대책을 강구해야 한다. 불투수 면적의 급격한 증가로 인하여 발생하는 이러한 현상들에 대응할 수 있는 대책은 여러 가지가 있다. 그중 하나로 대두되고 있는 것이 투수성 포장이다. 투수성 포장에 대한 관심과 연구는 계속되고 있고 일부 도 시나 주차장 같은 고압력이 가해지지 않는 곳에서는 사용이 되고 있다. 하지만 현재 투수성 포장의 가장 큰 취약점은 일반 아스팔트 포장보다 내구성이 크게 떨어진다는 것이다. 현재 투수성 포장의 가장 큰 과제는 내구성의 증대이다. 본 연구에서는 투수성 포장의 취약점인 내구성을 증가시키기 위하여 소석회를 첨가한 공극률 10%, 15%, 20%의 투수성 아스팔트 공시체를 제작하였다. 그리고 내구성을 파악하기 위해 수분 민감성을 평가 하였다. 각기 다른 공극률을 지닌 소석회 공시체 중에서 공극률이 15%인 소석회가 가장 좋은 내구성을 보였다. 공시체는 온도의 변화에 가장 크게 반응을 하였고 수분의 민감도에 따라서도 변화가 있었다. 이번 실험의 연구 방법으로는 새롭게 고안한 비파괴 충격파를 사용하였고 포장 재료의 동적 탄성 계수를 측정하여 재료의 물성치를 평가하였다.

PURPOSES : This study is to evaluate moisture susceptibility of asphalt mixtures by using non-destructive impact wave and to determine durability so as to decrease the gap between before and after freezing in the future. METHODS : Using non-destructive impact wave, this study is to determine the dynamic modulus of asphalt specimen. Furthermore, the results obtained from two experiment accelerometers are used for the dynamic modulus determination. The dynamic moduli of specimens are compared with those of the freezing-thawing specimens. RESULTS : Test results showed that the dynamic modulus before freezing and thawing environment loads at each temperature dropped about 3.7% after the environmental loads. Furthermore, correlation analysis indicates that transition of dynamic modulus at each point is about 89.59%. CONCLUSIONS: Evaluation of asphalt mixtures using non-destructive impact wave has excellent repeatability and simple equipment for the test. Consequently, the method in the study will be useful for evaluating the characteristics of a various asphalt mixtures.

Nondestructive instrumented indentation test is the method to evaluate the mechanical properties by analyzing load - displacement curve when forming indentation on the surface of the specimen within hundreds of micro-indentation depth. Resistance spot welded samples are known to difficult to measure the local mechanical properties due to the combination of microstructural changes with heat input. Particularly, more difficulties arise to evaluate local mechanical properties of resistance spot welds because of having narrow HAZ, as well as dramatic changed in microstructure and hardness properties across the welds. In this study, evaluation of the local mechanical properties of resistance spot welds was carried out using the characterization of Instrumented Indentation testing. Resistance spot welding were performed for 590MPa DP (Dual Phase) steels and 780MPa TRIP (Transformation Induced Plasticity) steels following ISO 18278-2 condition. Mechanical properties of base metal using tensile test and Instrumented Indentation test showed similar results. Also it is possible to measure local mechanical properties of the center of fusion zone, edge of fusion zone, HAZ and base metal regions by using instrumented indentation test. Therefore, measurement of local mechanical properties using instrumented indentation test is efficient, reliable and relatively simple technique to evaluate the tensile strength, yield strength and hardening exponent.

원전 부지에 저장중인 방사성폐기물을 처분장에 인도하기 전에 폐기물의 물리·화학적 특성이 인수기준에 적합한지를 검사해야 한다. 검사하는 방법 중 비파괴 검사방법에 대해 조사하였는데, 조사결과 X-ray를 이용한 비파괴 방법을 적용하면 인수검사 항목 중‘드럼내 내용물 검사’,‘ 유리수 및 채움율 정량검사’를 할 수 있는 것으로 나타났다. 본 논문에서는 먼저 X-ray 장비의 원리와 시스템 선정 시 고려해야 할 사항들에 대해 간략하게 살펴 본 후 X-ray 장비를 이용하여 검사해야 할 드럼들의 특성을 분석하였다. 분석한 특성들은 드럼의 종류, 드럼의 규격, 드럼내 내용물의 종류 등이었고 이들 특성자료를 이용하여 검사에 필요한 X-ray 소요에너지를 계산하였다. 계산 결과 드럼 크기가 320 ℓ 이하인 드럼을 검사하기 위한 소요에너지는 3 MeV 이하로 나타났으며 경제성 및 실현가능성 측면에서 450 keV 장비와 3 MeV 장비를 조합하거나 단독으로 사용하는 것이 바람직하고 이 때 450 keV 장비를 이용하여 검사가 가능한 저밀도 드럼수는 2006년 12월 저장기준으로 42,327 드럼, 3 MeV 장비를 이용하여 검사가 가능한 드럼 수는 18,105 드럼으로 나타났다. 검사를 수행하는 주체, 장비 구매 방안 등에 따라 4가지 검사 시나리오를 수립하고 이에 대해 경제성 및 적용 가능성을 분석한 결과 최적의 검사시나리오는 인수기준, 처리 및 처분장 인도에 대한 폐기물 발생자의 정책 등에 영향을 받는 것으로 나타났다. 예를들어,‘ 유리수’,‘ 채움율’에 대한 정량분석과‘내용물 확인’을 모두 해야 할 경우에는 밀도가 상대적으로 낮은 폐기물이 담겨있는‘저밀도 드럼’의 검사를 위해 450 keV 이동형 장비 2대를 구입하여 자체 검사하고‘고밀도 드럼’은 외주로 검사하는 것이 바람직할 수 있다. 반면‘내용물 확인’만을 비파괴 검사항목으로 할 경우에는 450 keV 급 이동형 장비 1대면 연간 13,000 드럼을 검사할 수 있는 것으로 나타났다.