PURPOSES : The purpose of this study is to confirm the thermal expansion characteristics of concrete mixed with 1% waste glass fine aggregates, which is the amount stipulated for recycled aggregates in the current quality standard. METHODS : The coefficient of thermal expansion was measured by applying AASHTOT 336-10 using a LVDT. The results measured were used as physical properties in a finite element analysis to confirm the change in tensile stress and the displacement of the right angle section of the upper slab of a concrete pavement due to admixture substitution. RESULTS : The thermal expansion coefficients of concrete based on the replacement rate of the admixture when the waste glass fine aggregates are replaced are within the range of the thermal expansion coefficients of concrete specified in the Federal Highway Administration report. As the replacement rate of the admixture increases, the thermal expansion coefficient of concrete decreases. As the thermal expansion coefficient decreases, the slab pavement curling displacement and the tensile stress of the center of the upper slab of concrete decrease. CONCLUSIONS : In the short term, the presence or absence of waste glass fine aggregates does not significantly affect the thermal expansion coefficient of concrete. However, in the long term, waste glass fine aggregates are reactive aggregates that causes ASR, which creates an expandable gel around the aggregates and results in concrete expansion. Therefore, the relationship between ASR and the thermal expansion coefficient must be analyzed in future studies.

PURPOSES : The objective of this study is to evaluate the mechanical properties of ternary blended cement concrete incorporated with pulverized reject ash (PRA) or pulverized fuel ash (PFA) based on a comparison with those of ordinary Portland cement (OPC) concrete. METHODS : To produce the concretes, the level of OPC replacement is set at 60%, which comprises 30%~45% ground granulate blast furnace slag and 15%~25% of fly ash (FA). The FA can be categorized into PFA, 4PRA (fineness 3,930 cm2/g3), and 8PRA (fineness 7,840 cm2/g3). The compressive strength, surface electric resistivity, initial absorption coefficient, and chloride ion penetrability of OPC and the ternary blended cement concrete are measured at predetermined periods after water curing. RESULTS : It is discovered that the mechanical properties of concrete with 8PRA are better than those of OPC concrete. The performance of 4PRA concrete is worse than that of 8PRA concrete, indicating that the fineness of the PRA can affect the mechanical properties of the ternary blended cement concrete. CONCLUSIONS : The use of PRA is feasible for the production of ternary blended cement concrete, provided that the appropriate mix design and grinding technology are used.

PURPOSES : The objective of this study is to quantitatively evaluate the visibility of a mixed-color asphalt pavement. METHODS : The visibility was compared and evaluated using a color pavement specimen, i.e., a pigment was added to the asphalt binder, which was used to fabricate a color pavement specimen, with red aggregate as the coarse aggregate, and the resultant difference in visibility was quantitively evaluated. The color asphalt mixture to which the pigment was added was prepared by varying the amount of pigment added — i.e., 3 %, 5 %, and 7 % of the total weight of the mixture — to confirm the change in visibility according to the amount of pigment added. For the color asphalt mixture with color aggregates, red-colored mudstone coarse aggregates(13mm and 10mm) were used. It is assumed that the surface of the produced specimen simulates the initial performance periods and the cut section of the specimen simulates the state of completion of the performance periods. RESULTS : The initial ΔE for the colored pavement exhibited the best visibility of WC-2-R. However, when considering the value of a in the red color pavement, the visibility of SMA13-R and WC-2-R was assessed as best; this is because SMA13-R exhibits a lower color difference than WC-2-R at the beginning of the performance periods but the red color is better. Upon completion of the colored pavement performance periods, the ΔE of each specimen using the SMA13-0C specimen as the reference specimen was high in SMA13-RC and ΔE using the WC-2-0C specimen as the reference specimen was also high in SMA13-RC. In addition, the a value is also higher than that of other mixtures so it is judged that the visibility of SMA13-RC is best when the performance periods are completed. CONCLUSIONS : The a value tended to increase with the increasing amount of pigment added at the beginning of the performance; however, it was found to decrease rapidly as the performance was completed. However, in the case of using SMA13-RC as the colored aggregate, since the color of the aggregate itself is red, it exhibits a constant value of 5.67 from the performance start to completion. Therefore, it is judged that a constant red color can be expressed during the performance period when the colored pavement using red colored aggregate is applied to the exclusive bus lane.

Sewerage age more rapidly than other facilities, leading to the destruction of the pipeline. Therefore, the replacement of old sewer pipes through long-term construction is costly. In order to solve this problem, this study investigated the ferronickel based sewer pipe with improved chemichal resistance and durability from concrete rigidity pipe. ABAQUS was used as the finite element analysis program and the load was calculated by the method given in the sewage facility standard. Therefore, the results of this study can be referenced in the design and construction of sewer pipes.

PURPOSES : Recently, bonded concrete overlay has been used as an alternative solution in concrete pavement rehabilitation since its material properties are similar to those of the existing concrete pavements. Deteriorated concrete pavements need rapid rehabilitation in order to prevent traffic jams on Korean expressways. Moreover, speedy and effective repair methods are required. Therefore, the use of bonded concrete overlay with ultra-rapid hardening cement has increased in an effort to reopen promptly the expressways in Korea. However, mobile mixer is required for ultra-rapid hardening cement concrete mixing in the construction site. The use of mobile mixer causes various disadvantages aforementioned such as limitation of the construction supply, open-air storage of mixing materials, increase in construction cost, and etc. In this study, therefore, hydration accelerator in-situ mixing on polymer modified concrete produced in concrete plant is attempted in order to avoid the disadvantages of existing bonded concrete overlay method using ultra-rapid hardening cement. METHODS: Bonded concrete overlay materials using ultra-rapid hardening cement should be meet all the requirements including structural characteristics, compatibility, durability for field application. Therefore, This study aimed to evaluate the application of hydration accelerator in-situ mixing on polymer modified concrete by evaluating structural characteristics, compatibility, durability and economic efficiency for bonded concrete overlay. RESULTS : Test results of structural characteristics showed that the compressive, flexural strength and bond strength were exceed 21MPa, 3.15MPa and 1.4MPa, respectively, which are the target strengths of four hours age for the purpose of prompt traffic reopening. In addition, tests of compatibility, such as drying shrinkage, coefficient of thermal expansion and modulus of elasticity, and durability (chloride ions penetration resistance, freezing-thawing resistance, scaling resistance, abrasion resistance and crack resistance), showed that the hydration accelerator in-situ mixing on polymer modified concrete were satisfied the required criteria. CONCLUSIONS: It was known that the hydration accelerator in-situ mixing on polymer modified concrete overlay method was applicable for bonded concrete overlay and was a good alternative method to substitute the existing bonded concrete overlay method since structural characteristics, compatibility, durability were satisfied the criteria and its economic efficiency was excellent compare to the existing bonded concrete overlay methods.

PURPOSES : In this study, wasted vinyl aggregate, which possesses better thermal properties than natural aggregate, was used in cement concrete mixture to develop more economical concrete with thermal insulation and freeze prevention effects. METHODS : Slump and air content of the fresh concrete, which substituted its 0%, 5%, and 10% of coarse aggregate with wasted vinyl aggregate, were measured. Compressive strength, Poisson’s ratio, elastic modulus, and splitting tensile strength of hardened concrete were measured by laboratory tests. Thermal properties of concrete such as coefficient of thermal expansion, thermal conductivity, and specific heat were also measured according to replacement ratio of wasted vinyl aggregate. Finally, the thermal insulation and freeze prevention effectiveness of the concrete mixed with wasted vinyl aggregate was confirmed through finite element analysis of road pavement crossing above concrete box culvert made from wasted vinyl aggregate. RESULTS: Even though the physical properties of wasted-vinyl-aggregate concrete such as compressive strength, Poisson°Øs ratio, elastic modulus, and splitting tensile strength were inferior to those of ordinary concrete, they met requirements for structural concrete. The thermal properties of concrete were improved by wasted vinyl aggregate because it decreased thermal conductivity and increased specific heat of the concrete. According to the result of finite element analysis, temperature variation in pavement subgrade was mitigated by box culvert made from wasted-vinyl-aggregate concrete. CONCLUSIONS: Through the laboratory test and finite element analysis of this study, it was concluded that the concrete structures made from wasted vinyl aggregate showed thermal insulation and freeze prevention effects.

This study is to find out if it can be recycled for making better concrete. Therefore, waste paper as of newspaper and newspaper are added into concrete to see if waste paper-mixing concrete can have any particular characteristic. The test result of paper concrete was compared and analyzed through four kinds of tests such as compressive strength as of a fundamental one of concrete resistant capacity against heat. 200℃, 400℃ and 600℃ heated concrete were compressively tested in order to find out concrete strength resistant to high temperature. heat capacity was also tested, based on the expectancy of its low conductivity. finally flexural strength test using four reinforced concrete beams with size of 20cm×30cm×160cm was made. And concrete property exposed to the temperature showed that there are almost not effect for the strength up to 400℃, but it was decreased down to 50% of the original condition. volume of paper mixed with concrete without relation to paper kinds of new and waste one.

Ordinary concrete uses aggregate sufficiently soaked with water, and is weighed, mixed with other materials and placed in accord with performances required in the construction field. Recently special concrete with high fluidity and durability is required but it is difficult to use top-quality concrete due to lack of high-quality aggregate, delayed transportation because of traffic jam, etc. In addition, sometimes the use of a remicon is inevitable just for small-sized concrete constructions or it is difficult for a remicon to reach remote construction places such as mountainous areas. To solve these problems, this study attempted to pack concrete materials. In other words, it is to instantize concrete. This study dried aggregate, a material of concrete, and compared the change of absorption phase of the aggregate in water and in paste in order to examine the effect of the dryness of aggregate on its absorption rate and, based on the absorption rate, decided water addition ratio necessary for the reduction of unit quantity caused by the use of dry aggregate in designing concrete mixture, and analyzed the properties of unhardened concrete according to water addition ratio in manufacturing concrete using aggregate in the state of absolute dryness and in the state of surface dryness.

본 논문은 가열 재생아스팔트 혼합물의 공용성능 향상을 위한 혼합방법 개발 연구의 일부분이다. 기존 재생혼합물 혼합방법은 재생혼합물 내에서 기존의 노화된 바인더가 균등히 회생되지 않다는 것을 확인하였다. 따라서 새로이 개발된 혼합방법은 회수 아스팔트 포장의 기존 바인더를 기존 재생 혼합방법보다 회수 아스팔트 포장 재료에 묻어 있는 노화된 바인더를 훨씬 많이 회생시켜 재생 혼합물에서 보다 더 균일한 바인더의 점도상태가 되도록 한다. 본 연구의 목적은 새로이 개발된 혼합 방법으로 제조된 재생아스팔트 혼합물의 피로저항 특성을 평가하는 것이다. 두 종류 골재(편마암, 화강암), RAP 15%, LDPE의 두 가지 첨가량(0, 6%)를 이용하였으며, 혼합방법은 바인더의 불균등 상태를 개선하기 위한 두 가지 방법, 즉 일반적인 기존의 O 방법과 새롭게 개발한 N 방법을 이용하였다. 혼합방법에 따른 피로저항성을 평가하기 위하여 혼합방법에 따라 제작한 재생 혼합물의 피로시험을 수행하였다. 그 결과, 피로수명은 O 방법 혼합물이 가장 길고 그 다음이 N 방법이고 control이 가장 낮았다. 또한 장기노화 후 N 방법 혼합물의 균열에 대한 저항성이 O 방법 혼합물에 비해 상대적으로 높아지고 있음을 알 수 있었다.