In this study, as the proportion of aged pipelines increases rapidly, in the event of an accident caused by corrosion and structural deterioration of metal pipes, appropriate overlay welding is applied in the field to partially repair it. The size of the base steel plate and the selection of a stable welding method were evaluated, and possible problems caused by the overlay welding were identified, and improvement measures were proposed. For the test, a new steel pipe coated with epoxy lining on the inner surface and polyethylene on the outer surface was subjected to a tensile test by processing the repaired specimen through overlay welding with a steel plate after artificial cracking, and structural safety was evaluated after repair. Furthermore, the influences of the size of the throat and the size of the steel plate were analyzed. As a result of the tensile test by dividing the repaired steel plate overlay into a constraint and non-constraint conditions, the tensile load was concentrated in the welded part and damage occurred in the welded part. It was found that the maximum load leading to breakage increases as the size of the welding throat increases. In addition, it was found that the resistance to load increased slightly as the size of the overlaid steel plate increased, but the effect was not significant, confirming the need for repair in consideration of the site conditions. As a result of evaluating the damage to the coating material on the back side of the welding, it was confirmed that the coating material on the opposite side of the welding burned black(epoxy) or was greatly deformed by heat(polyethylene). Therefore, it is necessary to secure structural stability through repainting, etc. in order to prevent damage to the coating material on the opposite side during overlay welding.

해수 중 존재하는 유해화학물질 검출을 목적으로 센서 시작품 제작하고 성능을 확인하였다. 센서 시작품은 검지부, 기구부, 구 동부로 구성하였다. 센서의 검지부는 ITO (Indium-Tin-Oxide) 금속산화물 나노입자 (metal oxide nanoparticle) 필름을 기판위에 인쇄하여 제작 하였고, 온도와 HNS 농도를 동시에 검출할 수 있도록 2개의 검출 부분을 갖도록 설계하였다. 센서의 기구부는 검지부와 구동부를 연결하 며, 검출에 영향을 줄 수 있는 화학적 반응을 막기 위해 테프론 재질을 이용하여 제작하였고, 특히 검지부의 착탈이 용이하도록 설계 하 였다. 구동부는 브릿지 회로와 아두이노 보드를 이용하여 전원 공급과 데이터 측정 및 디스플레이가 가능하도록 제작하였다. 시작품의 성 능에 대해서는 기존의 수질 센서를 참고한 성능 사양을 제시하고, 유기용제를 사용한 검지부와 시작품의 동작을 확인하여 응답 (ΔR), 검 출하한 (Limit of Detection), 응답시간 (response time), 오차 (error) 등을 평가하였다. 또한 해수 중 동작 특성을 파악하여 설계 사양이 구현되 었는지 확인하였다.

배관 시스템은 기체 및 액체 등의 에너지원을 수송하기 위해 사용되며 주로 건물 내부에 설치되거나 지반에 매립되 어 설치된다. 매립된 배관 시스템은 지진이나 지반침하와 같은 큰 상대변위를 받을 수 있으며 이는 배관의 연결부에 손상을 야 기할 수 있다. 벨로우즈는 기하학적 특성으로 축방향 및 회전 변형을 일부 허용한다. 그러므로 벨로우즈 신축관이음을 적용하면 큰 상대변위에 의한 손상을 줄일 수 있는 것으로 예상된다. 하지만 벨로우즈의 성형과정에서 회선의 벽 두께 감소가 발생할 수 있으며 이는 휨 및 인장 성능에 영향을 미칠 수 있다. 본 연구는 단조하중을 받는 벨로우즈 신축관이음의 성능을 분석하기 위 한 실험적 연구를 수행하였다. 또한 단조하중 실험 결과를 바탕으로 벨로우즈 신축관이음의 유한요소모델을 구축하였으며 실험 결과와 비교하여 검증하였다. 검증된 유한요소 모델을 이용하여 회선의 두께 감소에 의한 성능 변화를 분석하였다. 벽 두께 감 소율은 5%, 10%, 15%, 20%, 25%로 가정하였다. 해석 결과 인장 및 휨 하중에 따른 하중-변위 관계의 전체적인 강성과 최대 하 중이 감소하는 것으로 나타났다. 벽 두께 감소율이 25%일 때 인장 및 휨 하중에 따른 최대 하중은 각각 14%, 26% 감소하는 것 으로 나타났다.

PSC거더 합성교량에 있어 노후(손상)된 바닥판을 교체할 경우에는 기존에 설치된 철근 전단연결재의 손상과 함께 파 쇄에 따른 소음 및 비산먼지 등이 많이 발생한다. 이러한 환경적 문제와 함께 교체공사 기간이 길어져 경제적 비용 또한 크게 증가한다. 본 연구에서는 이러한 문제를 해결하기 위해 PSC거더에 매립되지만 쉽게 분리할 수 있는 분리식 전단연결재를 제안 하였다. 제안한 분리식 전단연결재의 전단강도성능과 파괴거동을 확인하기 위해 유한요소해석을 통한 변수연구와 함께 수평전 단실험을 수행하였다. 해석연구를 통해 T-sleeve 하부에 Y형상의 테이퍼진 면을 갖는 경우에 볼트체결력에 따른 쐐기효과로 인 해 T-sleeve와 볼트 사이의 제작 공차가 있더라도 초기 슬립이 발생하지 않고 충분한 초기강성을 확보하는 것을 확인하였다. 또 한, 전단연결재의 배치 방향에 따른 영향은 전단성능에 영향을 주지 않는 것을 확인하였다. DY전단연결재는 기존 방식인 철근 전단연결재 모델과 비교실험을 통해 전단강도성능은 동등 이상을 확보하고 있으며, 슬립변위량 또한 연성설계기준인 6mm 이상 을 만족하는 것을 확인하였다. 본 연구를 통해 제안된 분리식 전단연결재는 추가적으로 합성거더 실험 등의 검증을 거친다면 노후 바닥판의 철거 및 교체에 유용한 대안이 될 수 있을 것으로 판단된다.

PURPOSES : The purpose of this study was to quantitatively evaluate the variability of LiDAR performance indicators, such as intensity and Number of Point Cloud(NPC), according to various environmental factors and material characteristics. METHODS : To consider the material characteristics of road safety facilities, various materials (Reference Material(RM), reflective sheet, matte sheet, granite, plastic, and rubber) were used in a darkroom, and the performance indicators of LiDAR were repeatedly measured in terms of changes in the measurement distance, rainfall, and angle of observation. RESULTS : In the case of standard reflective materials, the intensity measurement value decreased as the measurement distance and rainfall increased. The NPC showed a tendency to decrease as the measurement distance increased, regardless of rainfall intensity. For materials with high-intensity values, it was found that rainfall intensity and color had negligible effect on the change in intensity compared with the measurement distance. However, for materials with low-intensity values, it was found that the measurement distance, rainfall intensity, and color all had a significant effect on the change in intensity. CONCLUSIONS : For materials with high-intensity values, it was found that rainfall and color had negligible effect on change in intensity compared with the measurement distance. However, for materials with low-intensity values, the measurement distance, rainfall, and color all had a significant effect on the change in intensity value.

PURPOSES : Experimental findings pertaining to the mechanical properties of calcium aluminate cement (CAC)-based repair mortars incorporated with anhydrite gypsum (AG) are described herein. METHODS : To prepare the mortars, three different levels of AG were adopted and the ratio of water–cementitious materials was fixed at 0.50. For comparison, mortar composed of ordinary Portland cement was prepared. The fluidity, setting time, compressive and bond strengths, absorption and surface electric resistivity of the mortars were measured at predetermined periods. RESULTS : The incorporation of AG increases the fluidity but decreases the setting time of the CAC-based repair material system. However, the AG in the CAC mixes does not effectively enhance the compressive strength of the mortars owing to the decreased formation of CA hydrates, such as CAH10 and C2AH8. Meanwhile, the mortar with 10% AG shows excellence absorption. CONCLUSIONS : The mechanical properties of CAC based-mortars rely significantly on the amount of AG incorporated. However, further studies regarding the microstructure and durability of CAC-AG repair mortars must be conducted to obtain the optimal mixture.

PURPOSES : Owing to industrial development, the occurrence of continuous environmental damage such as abnormal weather is accelerating because of a rapid increase in carbon emissions. Therefore, various efforts are expended worldwide to realize a low-carbon ecofriendly society. In the construction industry, various efforts have been realized to reduce environmental pollution such as greenhouse gas emissions, for example by introducing eco-friendly materials and reducing industrial waste. In this study, an asphalt pavement technology that can reduce production and construction temperatures by more than 60 °C is developed to reduce the amount of carbon generated in the asphalt industry. METHODS : The performance of a half-warm asphalt binder developed using thermoplastic elastomers and low-temperature additives was assessed. In addition, the change in the quality of a mixture due to the use of the half-warm asphalt binder was evaluated. RESULTS : As the amount of thermoplastic elastomer used increases, the performance grade of the asphalt binder increases as well. When 3% or more of the elastomer is incorporated, the target performance grade of the asphalt binder is satisfied. In addition, by incorporating the thermoplastic elastomer and a low-temperature additive, the overall moisture and rutting resistance increased even at relatively low production and compaction temperatures. CONCLUSIONS : Additional measures to stabilize quality and improve economic feasibility will present a new paradigm for investigations into eco-friendly asphalt concrete pavements.

The paper introduces an experimental program for the newly developed vertical joints between Precast Concrete (PC) walls to improve their in-plane shear capacity. Compared to the existing vertical joints, two types of vertical joints were developed by increasing the transverse reinforcement ratio and improving frictional force at the joint interface. A total of four specimens including the Reinforced Concrete (RC) wall and PC walls with developed vertical joints were designed and constructed. The constructed specimens were experimentally investigated through monotonic shear tests. The observed damage, load-deformation relationship, strain and strength are investigated and compared with the cases of RC wall specimen. Experimental results indicate that the maximum force and initial stiffness of the PC wall with proposed vertical joints were decreased by comparing with those of RC wall. However, the ultimate displacement increased by up to 217.30% compared to the RC wall specimen. In addition, brittle failure did not occurred and relatively few cracks and damages occurred.

In this study, an incremental loading test of the HRS(Hybrid Rubber Slit) damper was additionally performed to define the physical characteristics according to the incremental test results, and an analytical study was performed according to the damping design procedure by selecting an example structure. As a result of performing seismic performance evaluation before reinforcement by selecting a RC structure similar to an actual school structure as an example structure, the story drift ratio was satisfied, but some column members collapsed due to bending deformation. In order to secure the seismic performance, the damping design procedure of the HRS damper was presented and performed. As a result of calculating the amount of damping device according to the expected damping ratio and applying it to the example structure, the hysteresis behavior was stable without decrease in strength, and the story drift ratio and the shear force were reduced according to the damping effect. Finally the column members that had collapsed before reinforcement satisfied the LS Level.

It is effective to apply hybrid damping device that combine separate damping device to cope with various seismic load. In this study, HRS hybrid damper(hybrid rubber slit damper) in which high damping rubber and steel slit plate are combined in parallel was proposed and structural performance tests were performed to review the suitability for seismic performance. Cyclic Loading tests were performed in accordance with criteria presented in KDS 41 17 00 and MOE 2019. As a result of the test, the criteria of KDS 41 17 00 and MOE2019 was satisfied, and the amount of energy dissipation increased due to the shear deformation of the high-damping rubber at low displacement. Result of performing the RC frame test, the allowable story drift ratio was satisfied, and the amount of energy dissipation increased in the reinforced specimen compared to the non-reinforced specimen.

본 연구에서는 실대형 실험과 구조해석을 통해서 현장에서 사용되는 가새 시스템을 적용한 강관 골조 플라스틱 연동온실 의 횡하중 가력시험을 수행하고 성능을 분석하였다. 횡강성 과 응력을 분석하기 위해 실험체에 변위와 변형률계를 각각 9 개소 및 16개소 설치하였으며 가새의 설치 유무에 따른 성능 을 비교하기 위해 구조해석을 수행하였다. 실대형 실험과 가 새의 설치 유무에 따른 구조해석 결과 비교에서 구조물의 횡 강성이 많은 차이를 보였다. 실험체의 측고 부근에서 측정한 횡강성은 가새 시스템을 설치함으로 강성을 최대 44%까지 증 가시켰다. 현장에서 사용하는 가새의 접합부가 충분한 강성 을 확보하지 못함으로써 외력을 전체 구조물에 적절히 전달하 지 못하여 횡강성이 구조해석 결과보다 많이 저하되는 현상이 나타났다. 따라서 온실 설계 시 구조성능의 신뢰성을 높이기 위해서 가새 시스템의 연결방법, 설치위치, 부재의 최대길이 등 온실의 접합부에 대한 명확한 시공방법과 설계기준이 정립 되어 온실 설계가 이루어져야 할 것으로 판단된다.

본 논문에서는 프리팹 구조물의 품질관리를 위한 딥러닝 및 비전센서 기반의 조립 성능 평가 모델을 개발하였다. 조립부 검출을 위 해 인코더-디코더 형식의 네트워크와 수용 영역 블록 합성곱 모듈을 적용한 딥러닝 모델을 사용하였다. 검출된 조립부 영역 내의 볼트 홀을 검출하고, 볼트홀의 위치 값을 산정하여 k-근접 이웃 기반 모델을 사용하여 조립 품질을 평가하였다. 제안된 기법의 성능을 검증 하기 위해 조립부 모형을 3D 프린팅을 이용하여 제작하여 조립부 검출 및 조립 성능 예측 모델의 성능을 검증하였다. 성능 검증 결과 높은 정밀도로 조립부를 검출하였으며, 검출된 조립부내의 볼트홀의 위치를 바탕으로 프리팹 구조물의 조립 성능을 5% 이하의 판별 오차로 평가할 수 있음을 확인하였다.

콘크리트 충전강관은 국부좌굴을 방지하고 내화성이 향상되기 때문에 건설현장에서 많이 적용되며 휨성능을 향상시 키기 위해 강관 내부에 철근을 보강하여 사용한다. 그러나 철근은 부식되며 내구성이 저하되기 때문에 이를 대신할 소재에 대 한 연구가 진행되고 있다. 탄소섬유보강근은 철근에 비해 경량이며 고강도와 내부식성이 우수하다는 이점이 있다. 그러나 임계 온도가 250℃로 철근의 임계온도인 538℃에 비해 현저히 낮기 때문에 내화피복이 필요하다. 따라서 열전달해석을 통해 탄소섬 유보강근을 사용하였을 때 온도분포를 확인하고 P-M상관도를 도출하여 적용 가능여부를 확인하고자 한다. 해석결과 내화성능을 확보하기 위해 콘크리트 피복두께 40mm, 뿜칠내화피복재 30mm를 적용하거나 콘크리트 피복두께 60mm, 뿜칠내화피복재 20mm 를 적용하면 3시간 내화성능을 만족하는 것으로 평가되었다.

본 연구는 콘크리트구조기준(KDS 14-2021)을 적용한 RC보와 ACI 440.1R-15를 적용한 FRP 콘크리트의 비교 연구를 수행하였다. 파라미터 변수로 피복두께, FRP의 탄성계수 및 극한변형률 그리고 보강량 4가지로 설정하여 비교, 분석을 수행하였 다. 파라미터 연구 분석 결과 FRP의 탄성계수와 극한 변형률이 클수록 FRP 콘크리트의 휨성능이 우수하지만, 극한 응력이 동일 할 때 극한 변형률보다 탄성계수를 크게 하는 것이 유리하다. FRP 콘크리트가 인장지배 단면이나 변화구간 일 때 극한 변형률 증가에 휨성능이 비례해서 증가하지만 압축지배 단면일 경우에는 극한 변형률이 증가해도 휨성능은 증가하지 않는다. 또한, FRP 콘크리트는 최소 피복두께가 필요하지 않아 추가적인 휨성능이 17∼33% 증진 효과가 나타났다.

The recycling of solid waste materials to fabricate carbon-based electrode materials is of great interest for low-cost green supercapacitors. In this study, porous carbon foam (PCF) was prepared from waste floral foam (WFF) as an electrode material for supercapacitors. WFF was directly carbonized at various temperatures of 600, 800, and 1,000 oC under an inert atmosphere. The WFF-derived PCF (C-WFF) was found to have a specific surface area of 458.99 m2/g with multi-modal pore structures. The supercapacitive behavior of the prepared C-WFF was evaluated using a three-electrode system in a 6 M KOH aqueous electrolyte. As a result, the prepared C-WFF as an active material showed a high specific capacitance of 206 F/g at 1 A/g, a rate capability of 36.4 % at 20 A/g, a specific power density of 2,500 W/kg at an energy density of 2.68 Wh/kg, and a cycle stability of 99.96 % at 20 A/g after 10,000 cycles. These results indicate that the C-WFF prepared from WFF could be a promising candidate as an electrode material for high-performance green supercapacitors.

The purpose of this study is to evaluate seismic performances of a modular house system developed by a simple 4-clip fastening method and double metal assembly made of lightweight metals. In order to evaluate structural and non-structural seismic performances of the system. Shaking table test was carried out with full-scale modular units, and a nonlinear pushover analysis was performed to obtain suitable seismic responses for story drifts, displacements, force resistances and dynamic properties of the system. Through 3D analysis and shaking table test, the current method of lightweight modular metal unit assembly and systems with seismic performance of a 4-clip fastening type modular house were demonstrated safe and effective to seismic design.

New buildings have been designed using different seismic design standards that have been revised. However, the seismic performance of existing buildings is evaluated through the same performance evaluation guidelines. Existing buildings may not satisfy the performance targets suggested in the current guidelines, but there are practical limitations to discriminating the existing buildings with poor seismic performance through a full investigation. In this regard, to classify buildings with poor seismic performance according to the applied standard, this study aimed to evaluate performance-based investigation of the seismic design proposals of buildings with different design standards. The target buildings were set as RC ordinary moment frames for office occupancy. Changes in seismic design criteria by period were analyzed, and the design spectrum changes of reinforced concrete ordinary moment resisting frames were compared to analyze the seismic load acting on the building during design. The seismic design plan was derived through structural analysis of the target model, compared the member force and cross-sectional performance, and a preliminary evaluation of the seismic performance was performed to analyze the performance level through DCR. As a result of the seismic performance analysis through the derived design, the reinforced concrete ordinary moment frame design based on AIK 2000 has an insufficient seismic performance level, so buildings built before 2005 are likely to need seismic reinforcement.