이 연구에서는 녹차-목재섬유 복합보드에 강도성능과 기능성을 보강한 건축내장재를 개발하기 위하여 목재섬유에 녹차와 3종류의 숯을 혼합한 녹차-숯-목재섬유 복합보드를 제작하였고, 구성원료의 종류 및 그 배합비율이 복합보드의 동적탄성률에 미치는 영향을 조사하였다. 또한, 동적탄성률을 이용하여 비파괴적으로 정적 휨강도성능을 예측하였다. 녹차-숯-목재섬유 복합보드의 동적탄성률은 백탄함유 복합보드에서 전체적으로 약간 우수하였으나, 숯의 종류에 따른 차이는 크지 않았다. 녹차와 숯의 배합비율이 증가할수록 복합보드의 동적탄성률의 감소하였다. E1급 요소수지를 사용한 복합보드가 E0급 요소수지를 사용한 그것보다 높은 동적탄성률을 나타내었으나, 양수지간의 차이는 녹차-목재섬유 복합보드에 비해 현저히 적었고, 녹차-목재섬유 복합보드보다 현저한 동적탄성률의 향상을 나타내는 것이 확인되었다. 복합보드의 동적탄성률과 정적 휨 강도성능사이에 대부분 1%의 신뢰수준의 상관관계가 확인되어, 동적탄성률로부터 정적 휨 강도성능이 예측이 가능하였다.

본 연구에서는 1차항 판이론에 기반한 적층된 ACM 경사판의 기하학적 비선형 동적해석을 수행하였다. 비선형 동 적해를 구하기 위하여 Newmark 방법과 Newton-Raphson 반복법을 혼용하여 적용하였다. 본 연구에서 개발한 유한요 소 해석프로그램을 사용하여 경사각도와 적층 배열의 변화가 판의 기하학적 비선형 거동에 미치는 영향을 상세 분 석하였다. 몇 가지 수치해석 결과는 기존 연구자로부터 얻어진 결과와 잘 일치하는 것으로 나타났다. 본 연구의 새 로운 결과는 경사 적층 구조의 경사각도와 적층 배열과의 중요한 상호관계를 보여준다. 몇 가지 수치예제는 ACM 경사 적층판을 설계하는데 필요한 가이드라인을 제시하였다.

In this paper, the analysis of impact damage behavior of a reinforced concrete structure that undergoes both a shock impulsive loading and an impact loading due to the air blast induced from an explosion is performed. Firstly, a pair of multiple loadings are selected from the scenario that an imaginary explosion accident is assumed. The RC structures strengthened with advanced composite materials (ACM) are considered as a scheme for retrofitting RC wall structures subjected to multiple explosive loadings and then the evaluation of the resistant performance against them is presented in comparison with the result of the evaluation of a RC structure without a retrofit. Also, in order to derive the result of the analysis similar to that of real explosion experiments, which require the vast investment and expense for facilities, the constitutive equation and the equation of state (EOS) which can describe the real impact and shock phenomena accurately are included with them. In addition, the numerical simulations of two concrete structures are achieved using AUTODYN-3D, an explicit analysis program, in order to prove the retrofit performance of a ACM-strengthened RC wall structure.

Silver coated copper composite powders were prepared by electroless plating method by controlling the activation and deposition process variables such as feeding rate of silver ions solution, concentration of reductant and molar ratio of activation solution at room temperature. The characteristics of the product were verified by using a scanning electron microscopy (SEM), X-ray diffraction (XRD) and atomic absorption (A.A.). It is noted that completely cleansing the copper oxide layers and protecting the copper particles surface from hydrolysis were important to obtain high quality Ag-Cu composite powders. The optimum conditions of Ag-Cu composite powder synthesis were molar ratio 4, concentration of reductant 15g/l and feeding rate of silver ions solution 2 ml/min.

Carbon/silicon composites were synthesized by mixing silicon powders with petroleum pitch and subsequent heat-treatment. The resultant composites were composed of carbon and nano-size crystalline silicon identified by XRD and EDX. FIB images and SEM images were taken respectively to detect the existence of silicon impregnated in carbon and the distribution of silicon on the carbon surface. The obtained carbon/silicon materials were assembled as half cell anodes for lithium ion secondary battery and their electrochemical properties were tested. The pitch/silicon composite (3 : 1 wt. ratio) heat treated at 1000℃ and mixed with 55.5 wt.% of graphite showed relatively good electrochemical properties such as the initial efficiency of 78%, the initial discharge capacity of 605 mAh/g, and the discharge capacity of 500 mAh/g after 20 cycles.

Aluminum-based composites reinforced with various amounts of were produced by powder metallurgy (P/M). The machinability properties of were determined by means of cutting forces and surface roughness. Machining tests were carried out by using PCD and K10 tools. Increasing of volume fraction in the matrix resulted in a decrease of the surface roughness and turning forces. PCD cutting tools showed better cutting performance than K10 tools.

Austenitic stainless steel has been used as a corrosion resistance material. However, austenitic stainless steel has poor wear resistance property due to its low hardness. In this investigation, we apply powder composite process to obtain hard layer of Stainless steel. The composite material was fabricated from planetary ball milled SUS316L stainless steel powder and WC powder and then sintered by Pulsed Current Sintering (PCS) method. We also added TiC powder as a hard particle in WC layer. Evaluations of wear properties were performed by pin-on-disk wear testing machine, and a remarkable improvement in wear resistance property was obtained.

Nanostructured and composite powders have been prepared by mechanochemical reaction from mixtures of Ti, BN, and powders. The raw materials have reacted to form a uniform mixture of TiN, and or depending on the amount of used in the starting mixtures, and the reaction proceeded through so-called mechanically activated self-sustaining reaction (MSR). Fine TiN and crystallites less than a few tens of nanometer were homogeneously dispersed in the amorphous or matrix after milling for 12 hours. These amorphous matrices became crystalline phases after annealing at high temperatures as expected, but the original microstructure did not change significantly

Carbon composites were prepared with pitch-based round, C, hollow-type carbon fibers and pitch matrix. The thermal conductivities parallel and perpendicular to the fiber axis were measured by steady-state method. It was found that the thermal conductivities depended on the cross-sectional forms of the reinforcing fibers as well as the reinforcing orientation and carbon fiber precusors. Especially, mesophase pitch-based hollow carbon fiber-carbon composites had the most excellent thermal anisotropy, which was above 100.