Cu-Ti thin films were fabricated using a combinatorial sputtering system to realize highly sensitive surface acoustic wave (SAW) devices. The Cu-Ti sample library was grown with various chemical compositions and electrical resistivity, providing important information for selecting the most suitable materials for SAW devices. Considering that acoustic waves generated from piezoelectric materials are significantly affected by the resistivity and density of interdigital transducer (IDT) electrodes, three types of Cu-Ti thin films with different Cu contents were fabricated. The thickness of the Cu-Ti thin films used in the SAW-IDT electrode was fixed at 150 nm. As the Cu content of the Cu-Ti films was increased from 31.2 to 71.3 at%, the resistivity decreased from 10.5 to 5.8 × 10-5 ohm-cm, and the density increased from 5.5 to 7.3 g/cm3, respectively. A SAW device composed of Cu-Ti IDT electrodes resonated at exactly 143 MHz without frequency shifts, but the full width at half maximum (FWHM) values of the resonant frequency gradually increased as the Cu content increased. This means that although the increase in Cu content in the Cu-Ti thin film helps to improve the electrical properties of the IDT electrode, the increased density of the IDT electrode deteriorates the acoustic performance of SAW devices.

Accurate seismic vulnerability assessment requires high quality and large amounts of ground motion data. Ground motion data generated from time series contains not only the seismic waves but also the background noise. Therefore, it is crucial to determine the high-pass cut-off frequency to reduce the background noise. Traditional methods for determining the high-pass filter frequency are based on human inspection, such as comparing the noise and the signal Fourier Amplitude Spectrum (FAS), f2 trend line fitting, and inspection of the displacement curve after filtering. However, these methods are subject to human error and unsuitable for automating the process. This study used a deep learning approach to determine the high-pass filter frequency. We used the Mel-spectrogram for feature extraction and mixup technique to overcome the lack of data. We selected convolutional neural network (CNN) models such as ResNet, DenseNet, and EfficientNet for transfer learning. Additionally, we chose ViT and DeiT for transformer-based models. The results showed that ResNet had the highest performance with R2 (the coefficient of determination) at 0.977 and the lowest mean absolute error (MAE) and RMSE (root mean square error) at 0.006 and 0.074, respectively. When applied to a seismic event and compared to the traditional methods, the determination of the high-pass filter frequency through the deep learning method showed a difference of 0.1 Hz, which demonstrates that it can be used as a replacement for traditional methods. We anticipate that this study will pave the way for automating ground motion processing, which could be applied to the system to handle large amounts of data efficiently.

동해연안의 반폐쇄성 해역인 영일만에서 고주파해양레이더(HF-Radar)로 측정된 표층 해수유동 자료를 활용하여 1)바람과 수평 적인 해수유동 사이의 상관성을 파악하고 2)수직적으로 조밀한 간격의 층별 수온시계열 자료와 연계하여 수평적 및 수직적 해수유동의 특성을 파악하였다. 시계열 관측기간 중 영일만 해역의 전역에 걸쳐 북동풍이 우세하게 나타났을 때 표층부터 저층까지 수온의 급격한 상승이 동반되었다. 또한 표층의 장주기 해수유동에서도 풍향과 유사한 방향의 흐름이 뚜렷하게 관측되었다. 바람과 표층 해류 사이의 지 연상관 분석을 통해 영일만에 북동풍의 바람이 불기 시작하여 일정하게 지속된다면 짧은 시간(1 ~ 2시간) 내에 남서향의 표층 해류가 발 생되는 것을 확인하였다. 일평균된 장주기 표층 해류로부터 수렴과 발산을 계산하였고 이를 통해 층별 관측지점에서 발생한 두 번의 급 격한 저층수온 상승이벤트가 모두 영일만의 북동풍과 연관된 표층 해수(상대적 고온수)의 수렴(침강) 현상으로 인해 나타난 것으로 판단 하였다.

This paper takes six Chinese Textbooks in the late Korean Dynasty compiled by Wang Weihui and others as the research object, selects and counts the high-frequency words, and analyzes their characteristics from the aspects of syllable number, part of speech, use in modern Chinese, meaning content, dialect background and so on. It is found that only monosyllabic words and disyllabic words appear in the high-frequency words in the late Korean Chinese textbooks, and the parts of speech are mainly verbs and nouns. Modern Chinese uses some words of high-frequency words, and some high-frequency words are no longer used. In terms of meaning and content, high-frequency words are highly related to commercial and trade activities. At the same time, there are some spoken words and a large number of northeast dialect words.

Nuclear power plants in Korea were designed and evaluated based on the NRC's Regulatory Guide 1.60, a design response spectrum for nuclear power plants. However, it can be seen that the seismic motion characteristics are different when analyzing the Gyeongju earthquake and the Pohang earthquake that has recently occurred in Korea. Compared to the design response spectrum, seismic motion characteristics in Korea have a larger spectral acceleration in the high-frequency region. Therefore, in the case of equipment with a high natural frequency installed in a nuclear power plant, seismic performance may be reduced by reflecting the characteristics of domestic seismic motions. The failure modes of the equipment are typically structural failure and functional failure, with an anchorage failure being a representative type of structural failure. In this study, comparative analyses were performed to decide whether to consider the inelastic behavior of the anchorage or not. As a result, it was confirmed that the seismic performance of the anchorages could be increased by considering the inelastic behavior of an anchorage.

Background: The hamstring is a muscle that crosses two joints, that is the hip and knee, and its flexibility is an important indicator of physical health in its role in many activities of daily living such as sitting, walking, and running. Limited range of motion (ROM) due to hamstring tightness is strongly related to back pain and malfunction of the hip joint. High-frequency diathermy (HFD) therapy is known to be effective in relaxing the muscle and increasing ROM. Objects: To investigate the effects of HFD on active knee extension ROM and hamstring tone and stiffness in participants with hamstring tightness. Methods: Twenty-four participants with hamstring tightness were recruited, and the operational definition of hamstring tightness in this study was active knee extension ROM of below 160° at 90° hip flexion in the supine position. HFD was applied to the hamstring for 15 minutes using the WINBACK device. All participants were examined before and after the intervention, and the results were analyzed using a paired t-test. The outcome measures included knee extension ROM, the viscoelastic property of the hamstring, and peak torque for passive knee extension. Results: The active knee extension ROM significantly increased from 138.8° ± 9.9° (mean ± standard deviation) to 143.9° ± 10.4° after the intervention (p < 0.05), while viscoelastic property of the hamstring significantly decreased (p < 0.05). Also, the peak torque for knee extension significantly decreased (p < 0.05). Conclusion: Application of HFD for 15 minutes to tight hamstrings immediately improves the active ROM and reduces the tone, stiffness, and elasticity of the muscle. However, further experiments are required to examine the long-term effects of HFD on hamstring tightness including pain reduction, postural improvement around the pelvis and lower extremities, and enhanced functional movement.

Background: The gastrocnemius (GCM) is one of the lower extremity muscles that tend to tighten easily. GCM tightness results in limited ankle dorsi-flexion (DF), especially when the knee joint is fully extended. Joint flexibility is determined by the morphological and physiological characteristics of joints, muscles, tendons, and ligaments. Impaired joint flexibility can be attributed to increased susceptibility to muscle injury. High-frequency diathermy is clinically used to reduce pain and muscle tightness and to improve limited range of motion. Objects: This study aimed to investigate the immediate effects of high-frequency therapy in subjects with GCM tightness. Methods: The study was designed as a one-group before–after trial. The subjects included 28 volunteers with GCM tightness (an active ankle DF angle of less than 12°) without any known neurological and musculoskeletal pathologies in the ankle and calf areas. WINBACK Transfer Electrode Capacitive and Resistive Therapy equipment was used to apply high-frequency therapy to the subjects’ GCMs for 10–15 minutes. The pennation angle and the fascicle length of the GCM were measured using ultrasonography. The flexibility of the ankle joint, peak torque to the passive ankle DF (Biodex), and soft tissue stiffness (MyotonPRO) were also measured. Results: The pennation angle was significantly decreased following the treatment; however, no significant difference in the fascicle length was found (p < 0.05). The flexibility was significantly increased and both the passive peak torque to passive ankle DF and the soft tissue stiffness significantly decreased (p < 0.05). Conclusion: High-frequency therapy is immediately effective for improving the muscle’s architectural properties and functional factors in subjects with GCM tightness. Further longitudinal clinical studies are required to investigate the long-term effects of high-frequency therapy on subjects with GCM tightness from various causes.

Analysis of the 2016 Gyeongju earthquake and the 2017 Pohang earthquake showed the characteristics of a typical high-frequency earthquake with many high-frequency components, short time strong motion duration, and large peak ground acceleration relative to the magnitude of the earthquake. Domestic nuclear power plants were designed and evaluated based on NRC's Regulatory Guide 1.60 design response spectrum, which had a great deal of energy in the low-frequency range. Therefore, nuclear power plants should carry out seismic verification and seismic performance evaluation of systems, structures, and components by reflecting the domestic characteristics of earthquakes. In this study, high-frequency amplification factors that can be used for seismic verification and seismic performance evaluation of nuclear power plant systems, structures, and equipment were analyzed. In order to analyze the high-frequency amplification factor, five sets of seismic time history were generated, which were matched with the uniform hazard response spectrum to reflect the characteristics of domestic earthquake motion. The nuclear power plant was subjected to seismic analysis for the construction of the Korean standard nuclear power plant, OPR1000, which is a reactor building, an auxiliary building assembly, a component cooling water heat exchanger building, and an essential service water building. Based on the results of the seismic analysis, a high-frequency amplification factor was derived upon the calculation of the floor response spectrum of the important locations of nuclear power plants. The high-frequency amplification factor can be effectively used for the seismic verification and seismic performance evaluation of electric equipment which are sensitive to high-frequency earthquakes.

In 2016, an earthquake occurred at Gyeongju, Korea. At the Wolsong site, the observed peak ground acceleration was lower than the operating basis earthquake (OBE) level of Wolsong nuclear power plant. However, the measured spectral acceleration value exceeded the spectral acceleration of the operating-basis earthquake (OBE) level in some sections of the response spectrum, resulting in a manual shutdown of the nuclear power plant. Analysis of the response spectra shape of the Gyeongju earthquake motion showed that the high-frequency components are stronger than the response spectra shape used in nuclear power plant design. Therefore, the seismic performance evaluation of structures and equipment of nuclear power plants should be made to reflect the characteristics of site-specific earthquakes. In general, the floor response spectrum shape at the installation site or the generalized response spectrum shape is used for the seismic performance evaluation of structures and equipment. In this study, a generalized response spectrum shape is proposed for seismic performance evaluation of structures and equipment for nuclear power plants. The proposed response spectrum shape reflects the characteristics of earthquake motion in Korea through earthquake hazard analysis, and it can be applied to structures and equipment at various locations.

In this study, 70 kinds of nutritional composition for five bokkeumbap products(spicy chicken, shrimp(saeu), haemul, nakji, and barbecue bokkeumbap) in high-frequency processed foods were analyzed. Raw data of intake amounts were collected from the 7th Korea National Health and Nutrition Examination Survey. Regarding proximate composition, spicy chicken bokkeumbap had lower water content and higher carbohydrate content than other bokkeumbaps, resulting in the highest total calories. The proximate composition of other bokkeumbaps were all distributed within a similar range. Vitamin content differed according to ingredients added to the bokkeumbaps. Haemul bokkeumbap had high content of vitamins B1 and B2, nakji bokkeumbap had high content of vitamin C and β-carotene, and barbecue bokkeumbap had high content of total niacin, folic acid, and vitamin A. For mineral content, barbecue bokkeumbap showed the highest content distribution, while nakji bokkeumbap showed the lowest content distribution. Regarding fatty acid and fat content, the highest content of fatty acids, saturated fats, and trans fats was detected in shrimp(saeu) bokkeumbap. For amino acid content, barbecue bokkeumbap showed highest content distribution. These results can be used as salient basic data for a food nutrient composition database and to significantly contribute to consumers’ health.

In this study, the formation, microstructure, and wear properties of Colmonoy 88 (Ni-17W-15Cr-3B-4Si wt.%) + Stellite 1 (Co-32Cr-17W wt.%) coating layers fabricated by high-velocity oxygen fuel (HVOF) spraying are investigated. Colmonoy 88 and Stellite 1 powders were mixed at a ratio of 1:0 and 5:5 vol.%. HVOF sprayed selffluxing composite coating layers were fabricated using the mixed powder feedstocks. The microstructures and wear properties of the composite coating layers are controlled via a high-frequency heat treatment. The two coating layers are composed of γ-Ni, Ni3B, W2B, and Cr23C6 phases. Co peaks are detected after the addition of Stellite 1 powder. Moreover, the WCrB2 hard phase is detected in all coating layers after the high-frequency heat treatment. Porosities were changed from 0.44% (Colmonoy 88) to 3.89% (Colmonoy 88 + ST#1) as the content of Stellite 1 powder increased. And porosity is denoted as 0.3% or less by inducing high-frequency heat treatment. The wear results confirm that the wear property significantly improves after the high-frequency heat treatment, because of the presence of wellcontrolled defects in the coating layers. The wear surfaces of the coated layers are observed and a wear mechanism for the Ni-based self-fluxing composite coating layers is proposed.

During the winter of 2017/2018, significantly low water temperatures were detected around the western and southern coasts of Korea (WSCK). In this period, sea surface temperature (SST) in the Korea Waters was about 2℃ lower than mean temperature. Using the real-time observation system, we analyzed the temporal variation of SST during this period around the western and southern coasts. Low water temperature usually manifested over a period of about 10 ~ 20 days. The daily Arctic oscillation index was also similarly detectable with the variation of SST. From the cross-correlation function, we compared two periodic variations, which were SST around the WSCK and the Arctic oscillation index. The cross correlation coefficients between both variations were approximately 0.3 ~ 0.4. The time lag of the two time series was about 6 to 7 days. Therefore, significanlyt low water temperatures during winter in the Korean coastal areas usually became detectable 6 to 7 days after the negative peak of Arctic oscillation.

The purposes of this study are to analyze high-frequency hedges in dissertations and provide basic data for Korean education for academic purposes. For these purposes, the investigator analyzed ‘-(으)ㄹ 수 있 다, -(으)ㄹ 것이다, and -(으)로 보이다’ in terms of frequency, distribution by the structure, and forms of combination in 50 dissertations for a master’s degree. The findings were as follows: first, ‘-(으)ㄹ 수 있다, -(으)ㄹ 것이다, and -(으)로 보이다’ were used total 3,880 times across all the dissertations. Of them, ‘-(으)ㄹ 수 있다’ were used 2,496 times, recording an overwhelmingly higher frequency than the others. Secondly, the study analyzed the frequency of hedges by the part in dissertations and found that hedges were most used in “Findings”(56.6%). Finally, there were standardized forms frequently combined with each hedge. ‘-(으)ㄹ 수 있다,’ for instance, was frequently used in the forms of ‘-(이)라고 할 수 있다/다고 할 수 있다,’ ‘-(으)ㅁ을 알 수 있다,’ and ‘-다는 것을 알 수 있다.’

High power trends in the diesel engines due to engine downsizing do not provide noise attenuation that can be satisfied with the performance of the existing silencer on account of high frequency increases in the exhaust noise. This study improves the attenuation performance of the exhaust silencer of the diesel engine and suggests silencer structure that performs best attenuation performance, especially at the high frequency range in the exhaust noise. It proposes dual silencer structure with an average attenuation performance of 6.4 dB and a maximum of 10.7 dB in the high frequency range (over 500 Hz), and analyzes its characteristics compared with the existing silencer. The performance analysis is performed according to 'Measurements on silencers in situation–ISO 11820:1996 Acoustics' and describes the results of comparative analysis with the existing silencer.

위험유해물질은 해양에 유입되었을 때 인간의 건강 및 해양생태계에 막대한 영향을 미치는 물질로 정의된다. 최근 선박을 이용한 물동량이 증가되면서 위험유해물질 누출사고의 발생비율도 증가되는 추세이다. 이에 따라 위험유해물질 누출사고 대응기술개발의 관점에서 해저에 침적되는 물질들의 방제 및 모니터링 연구가 수행되어야 한다. 본 논문에서는 저층 침적 위험유해물질의 음향 탐지 가능성을 확인하기 위해 저층 침적 위험유해물질 대체물질의 반사손실 측정 실험이 수행되었다. 위험유해물질로 구분되는 클로로폼의 위험성을 고려하여 클로로폼과 임피던스가 유사한 피마자유가 대체물질로 사용되었으며, 200 kHz 고주파 신호를 송신하여 물과 피마자유 경 계면에서 발생되는 반사손실을 측정하였다. 그리고 물과 피마자유의 임피던스를 측정 및 조사하여 반사계수를 모의하고 모의된 반사손실이 측정값과 유사함을 확인하였다. 또한 저층 침적 위험유해물질로 분류되는 클로로폼의 반사손실을 모의하고 모의 결과가 다양한 해저면 구성성분의 반사손실 모의결과와 차이를 나타냄으로써 해저면과 구분되는 저층 침적 위험유해물질의 음향 탐지 가능성을 예측하였다.

This study is a study on the cracking of the main piston surface which is generated in the injection molding machine to generate mold force. The main piston machining process consists of high frequency heat treatment, grinding and super finishing after lathe turning. Scale, defect size, and fracture texture were observed for four cracks on the surface of the piston during the tempering process after high frequency heat treatment using a metallurgical microscope. In this study, it was confirmed that the cracked structure of the piston structure was ferrite and pearlite structure. It was confirmed that cracks progressed to 480 ㎛ and scale layer of 3 ㎛ or less. Surface hardening layer and hardness were min 2.0mm/HRc 58±2 spec 1.6 mm/HRc 56.5~57.5 In addition, cracks on the surface of the piston appear perpendicular to the rolling process. Therefore, it can be assumed that the crack occurred in the low temperature tempering process at 200°C or less after the high frequency heat treatment, not the material defect. Therefore, the temperature should be maintained at 200°C or higher during tempering after high-frequency heat treatment, and the cracking defect on the surface of the piston can be prevented by setting the feed rate to 1.3 mm/s or less during heat treatment.