리튬이온전지는 친환경적이고 우수한 전지 성능덕분에 배터리 산업의 핵심으로 자리 잡았으며, 이에 따라 수요가 급증하고 있다. 그러나, 리튬이온전지의 수요증가는 리튬과 광물자원들의 공급문제를 초래하며, 수명이 다한 폐 리튬이온전지의 폐기방안이 아직 마련되지 않아 환경적 문제를 발생시킨다. 이러한 문제를 해결하기 위해 폐 리튬이온전지를 재활용하는 연구가 진행되고 있으며, 그 중에서도 폐 리튬이온전지에서 폐 양극 소재를 추출하여 재활용하는 다이렉트 리사이클링 연구가 주목받고 있다. 그러나, 폐 양극 소재는 오랜 충/방전으로 인해 구조적 붕괴(열화)가 발생한 상태로, 새로운 리튬이온전지에 적용을 위해서는 리튬이온전지 사용 전의 구조 즉, 층상구조로의 회복이 필요하다. 본 연구에서는 이를 위해 폐 양극 소재(LiNi0.6C0.2Mn0.2O2)가 열역학적으로 층상구조를 형성하는 온도를 분석하기 위해 700 ºC, 800 ºC, 900 ºC 범위에서 XRD를 통해 구조분석을 진행하였다. 폐 양극 소재는 700 ºC와 900 ºC 대비 800 ºC 열처리 시 1.44로 가장 높은 I003/I104 value를 보였다. 또한 800 ºC 열처리 시 0.1 C 기준 비 용량이 171.3 mAh/g으로 가장 높은 것을 확인하였다. 이를 통해 우리는 열역학적으로 층상구조를 형성하는 온도를 800 ºC로 도출하였으며 폐 양극 소재의 구조를 성공적으로 복원하였다.

환경오염을 제어하기 위한 청정에너지에 대한 수요 증가는 빠르게 증가하고 있습니다. 리튬 이온 배터리와 같은 충전식 배터리는 청정에너지의 우수한 원천이지만 높은 수요와 공급 불일치로 인해 리튬 금속이 빠르게 고갈되고 있습니다. 배터리 폐기물에서 귀금속을 회수하는 것은 환경오염 제어와 함께 가능한 해결책 중 하나입니다. 멤브레인 기반 분리 방법은 폐기물에서 리튬을 회수할 수 있는 매우 성공적인 상업적 공정입니다. 이 작업은 최근에 보고된 다양한 방법을 다룰 것이며 검토 형식으로 작성될 것입니다.

The lithium-ion battery has been utilized in various fields including energy storage system, portable electronic devices and electric vehicles due to their high energy and power densities, low self-discharge, and long cycle-life performances. However, despite of various research on electrode materials, there is a lack of research on developing of binder to replace conventional polymer-based binding materials. In this work, petroleum pitch (MP-50)/polymer (polyurethane, PU) composite binder for lithium-ion battery has fabricated not only to use as a binding material, but also to re-place conventional polymer-based binder. The MP-50/PU composite binder has also prepared to various ratios between petroleum pitch and polymer to optimize the physical and electro-chemical performance of the lithium-ion battery based on the MP-50/PU composite binder. The physical and electrochemical performances of the MP-50/PU composite binder-based lithium-ion battery were evaluated using a universal testing machine (UTM), charge/discharge test. As a result, lithium-ion battery based on the MP-50/PU composite (5:5, mass ratio) binder showed optimized performances with 1.53 gf mm− 1 of adhesion strength, 341 mAh g− 1 of specific discharge capacity and 99.5% of ICE value.

As the demand for lithium-ion batteries for electric vehicles is increasing, it is important to recover valuable metals from waste lithium-ion batteries. In this study, the effects of gas flow rate and hydrogen partial pressure on hydrogen reduction of NCM-based lithium-ion battery cathode materials were investigated. As the gas flow rate and hydrogen partial pressure increased, the weight loss rate increased significantly from the beginning of the reaction due to the reduction of NiO and CoO by hydrogen. At 700 °C and hydrogen partial pressure above 0.5 atm, Ni and Li2O were produced by hydrogen reduction. From the reduction product and Li recovery rate, the hydrogen reduction of NCM-based cathode materials was significantly affected by hydrogen partial pressure. The Li compounds recovered from the solution after water leaching of the reduction products were LiOH, LiOH·H2O, and Li2CO3, with about 0.02 wt% Al as an impurity.

최근 전기차 및 전력저장 시스템과 같은 대형 전지 시장의 성장으로 인해 리튬 이온 배터리에 대한 수요가 급증하 고 있다. 이에 따라 폐전지의 발생이 빠르게 증가할 것 으로 예상되며, 이에 대한 처리가 사회적 문제가 될 것 으로 예상된다. 폐전지 처리의 가장 효과적인 방법은 폐전지의 소재를 재활용하는 방법이다. 이 중 고가의 금속 물질로서, 재활용 시 경제성이 가장 높은 양극 소재 재활용 연구가 가장 활발히 이뤄지고 있다. 하지만 폐전지로부터 회수된 블 랙 파우더에는 도전재 및 바인더가 포함되어 있는데 양극 소재를 재활용하기 위해서는 이를 제거하는 공정이 필요하 다. 본 연구에서는 폐전지에서 추출된 폐양극 소재의 재활용을 위한 소재 전처리 연구를 제시한다. 열처리 및 화학 처리의 두 가지 전처리 공정을 사용하여 불순물을 제거하였고, 이에 따른 제거 정도를 SEM 분석을 통해 확인하였고, 불순물의 정량 분석을 TGA, EA 분석을 통해 확인하였으며, 전기화학 성능을 분석하였다.

The complexation of silicon with carbon materials is considered an effective method for using silicon as an anode material for lithium-ion batteries. In the present study, carbon frameworks with a 3D porous structure were fabricated using metal–organic frameworks (MOFs), which have been drawing significant attention as a promising material in a wide range of applications. Subsequently, the fabricated carbon frameworks were subjected to CVD to obtain silicon-carbon complexes. These siliconcarbon complexes with a 3D porous structure exhibited excellent rate capability because they provided sufficient paths for Li-ion diffusion while facilitating contact with the electrolyte. In addition, unoccupied space within the silicon complex, combined with the stable structure of the carbon framework, allowed the volume expansion of silicon and the resultant stress to be more effectively accommodated, thereby reducing electrode expansion. The major findings of the present study demonstrate the applicability of MOF-based carbon frameworks as a material for silicon complex anodes.

The lithium ion battery has applied to various fields of energy storage systems such as electric vehicle and potable electronic devices in terms of high energy density and long-life cycle. Despite of various research on the electrode and electrolyte materials, there is a lack of research for investigating of the binding materials to replace polymer based binder. In this study, we have investigated petroleum pitch/polymer composite with various ratios between petroleum pitch and polymer in order to optimize the electrochemical and physical performance of the lithium-ion battery based on petroleum pitch/polymer composite binder. The electrochemical and physical performances of the petroleum pitch/polymer composite binder based lithium-ion battery were evaluated by using a charge/discharge test, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and universal testing machine (UTM). As a result, the petroleum pitch(MP-50)/polymer(PVDF) composite (5:5 wt % ratio) binder based lithium-ion battery showed 1.29 gf mm-1 of adhesion strength with 144 mAh g-1 of specific dis-charge capacity and 93.1 % of initial coulombic efficiency(ICE) value.

In order to apply to high-nickel cathodes for high-capacity and stability enhancement of lithium-ion batteries, the characteristics of the coating film were reviewed using the conventional nickel plating method. The surface morphology of the plating layer and the measurement of the surface roughness were analyzed according to scan size and rate using the contact mode of Atomic Force Microscopy. The hydrogen ion concentration (pH) of the electrolyte played an important role in shaping the metal ion plating. As the overpotential of the surface increased during plating, the crystals grew in a direction other than the main crystal growth direction. The increase in on-time during pulse plating appears to result in coarse particles as much of the applied current is consumed by the reduction of hydrogen ions, resulting in lower current efficiency. From the AFM image, it was confirmed that the blackening of the plated film was due to a partial overvoltage phenomenon during electrolytic degreasing. In order to be used as a high-nickel cathode, it seems that the current must be uniformly distributed on the surface of the substrate during plating.

Lithium-ion batteries (LIBs) are powerful energy storage devices with several advantages, including high energy density, large voltage window, high cycling stability, and eco-friendliness. However, demand for ultrafast charge/discharge performance is increasing, and many improvements are needed in the electrode which contains the carbon-based active material. Among LIB electrode components, the conductive additive plays an important role, connecting the active materials and enhancing charge transfer within the electrode. This impacts electrical and ionic conductivity, electrical resistance, and the density of the electrode. Therefore, to increase ultrafast cycling performance by enhancing the electrical conductivity and density of the electrode, we complexed Ketjen black and graphene and applied conductive agents. This electrode, with the composite conductive additives, exhibited high electrical conductivity (12.11 S/cm), excellent high-rate performance (28.6 mAh/g at current density of 3,000 mA/g), and great long-term cycling stability at high current density (88.7 % after 500 cycles at current density of 3,000 mA/g). This excellent high-rate performance with cycling stability is attributed to the increased electrical conductivity, due to the increased amount of graphene, which has high intrinsic electrical conductivity, and the high density of the electrode.

Lithium-ion battery (LiB) is one of the special issues on nowadays and diverse researches to develop LiB with better performances have been carried out so far, especially, regarding improved properties of each component such as cathode, anode, separator and electrolyte. However, there are limited information on ‘processing’ to prepare each component, and especially fabrication of cathode is strongly dependent on thinky mixer to realize homogeneous dispersion of active materials and conductors in binders. Herein, we report on preparation of LiNi0.8Co0.1Mn0.1O2 (NCM811) based cathode materials with different carbon conductors (CNT and carbon black) using homogenizer and three-roll milling method. These processes are turned out perfect alternative to prepare cathode electrode. LiB cells were assembled using the dispersed electrode slurry and the performance of a cell was electrochemically stable, even in the case of a CNT conductor, which is normally difficult to make perfect dispersion because of its strong Van der Waals attraction between the tubes and π–π interactions.

Tin/graphite composites are prepared as anode materials for Li-ion batteries using a dry ball-milling process. The main experimental variables in this work are the ball milling time (0–8 h) and composition ratio (tin:graphite=5:95, 15:85, and 30:70 w/w) of graphite and tin powder. For comparison, a tin/graphite composite is prepared using wet ball milling. The morphology and structure of the different tin/graphite composites are investigated using X-ray diffraction, Raman spectroscopy, energy-dispersive X-ray spectroscopy, and scanning and transmission electron microscopy. The electrochemical properties of the samples are also examined. The optimal dry ball milling time for the uniform mixing of graphite and tin is 6 h in a graphite-30wt.%Sn sample. The electrode prepared from the composite that is dry-ballmilled for 6 h exhibits the best cycle performance (discharge capacity after 50th cycle: 308 mAh/g and capacity retention: 46%). The discharge capacity after the 50th cycle is approximately 112 mAh/g, higher than that when the electrode is composed of only graphite (196 mAh/g after 50th cycle). This result indicates that it is possible to manufacture a tin/graphite composite anode material that can effectively buffer the volume change that occurs during cycling, even using a simple dry ball-milling process.

The high level of lithium storage in synthetic porous carbons has necessitated the development of accurate models for estimating the specific capacity of carbon-based lithium-ion battery (LIB) anodes. To date, various models have been developed to estimate the storage capacity of lithium in carbonaceous materials. However, these models are complex and do not take into account the effect of porosity in their estimations. In this paper, a novel model is proposed to predict the specific capacity of porous carbon LIB anodes. For this purpose, a new factor is introduced, which is called normalized surface area. Considering this factor, the contribution of surface lithium storage can be added to the lithium stored in the bulk to have a better prediction. The novel model proposed in this study is able to estimate the lithium storage capacity of LIB anodes based on the porosity of porous carbons for the first time. Benefiting porosity value (specific surface area) makes the predictions quick, facile, and sensible for the scientists and experts designing LIBs using porous carbon anodes. The predicted capacities were compared with that of the literature reported by experimental works. The remarkable consistency of the measured and predicted capacities of the LIB anodes also confirms the validity of the approach and its reliability for further predictions.

The enhancement of heat transfer in cooling system of cylindrical lithium-ion battery pack is numerically investigated by installing fins on the cooling plate. Battery Design StudioⓇ software is used for modeling electro-chemical heat generation in the battery and the conjugated heat transfer is analyzed with the commercial package STAR-CCM+. The result shows that installing fins on the cooling plate increases the convective heat transfer on the surface and thus lowers the maximum temperature of the battery pack. As the length and thickness of the fins increase, heat transfer in the battery pack improves. Considering the geometry and airflow of the battery pack, the optimal values for the length and thickness of the fin are both 2mm. As the convective heat transfer coefficient of the surface increases, the maximum temperature of the battery pack is greatly reduced and the temperature gradient is greatly improved.

Morphology control of a graphene nanosheet (GNS) is important for graphene-based battery electrodes to exhibit the increased practical surface area and the enhanced ion diffusion into the nanosheets. Nevertheless, it is very difficult to minutely control the shape of graphene nanosheets based on the conventional GNS suspension methods. In this work, we fabricated wrinkle textures of free-standing GNS for large area using Langmuir–Schaefer technique. The wrinkles are oriented vertically to the direction of the monolayer compression. The textured structure of GNS was obtained by cross-deposition of each layer with controlling the orientation of the wrinkle direction. These wrinkles can cause Li-ion to diffuse into the voids created by them and raise the specific surface area between the GNSs. Consequently, as a prospective anode for Li-ion battery, the wrinkled GNS multilayer, exhibits the high specific capacity of ~ 740 mAh g− 1 at 100 mA g−1 and the great power capability with ~ 404 mAh g− 1 being delivered even at 2 A g− 1. Furthermore, outstanding cycle performance of the wrinkled GNS multilayer is achieved over 200 cycles at 300 mA g−1 with high Coulombic efficiency of ~ 96%.

In this study, soybean oil, which is used in a large variety of processed foods, is used as a carbon source. Soybean oil is successfully coated onto the surface of LiNi1/ 3Co1/3Mn1/3O2 (NCM) by a simple method. The physical and electrochemical properties of NCM/C hybrid materials are determined. As a result, a 5 nm thickness carbon coating layer is formed on the surface of the NCM, resulting in improved capability and cyclic performance in the battery. The NCM/C battery shows an initial discharge capacity of 159 mAh g−1 and 95% capacity retention after 100 cycles (a discharge capacity of 120 mAh g−1 and 94% retention are observed after 100 cycles for the NCM cathode).

The effect of flow direction on heat transfer in water cooling channel of lithium-ion battery is numerically investigated. Battery Design StudioⓇ software is used for modeling electro-chemical heat generation in the battery and the conjugated heat transfer is analyzed with the commercial package STAR-CCM+. The result shows that the maximum temperature and temperature difference of battery with Type 1 are the lowest because the heat transfer in the entrance region near the electrode is enhanced. As the inlet velocity is increased, the maximum temperature and temperature difference of battery decreases but the pressure loss increases. The pressure loss in Type 2 channel is the lowest due to the shortest channel length, while the pressure loss with Type 3 or 4 channel is the highest because of the longest channel length. Considering heat transfer performance and pressure loss, Type 1 is the best cooling channel.

The carbon anode material for lithium-ion battery was prepared by pyrolysis fuel oil and waste polyethylene terephthalate (PET) additive. The pitch was synthesized as a medium material for carbon anode by heat treatment. The waste PET additive improved the softening point and thermal stability of the pitch. La and Lc of the anode material (heat-treated pitch) increased at higher treatment temperature but decreased by waste PET additive. The electric capacity was evaluated based on effects of defective cavity and developed graphite interlayer, respectively. When the La and Lc of the anode material decreased, the electric capacity by cavity increased based on defective graphite structure. Therefore, the addition of waste PET causes the improved capacity by the cavity. The anode material which has a high efficiency (over 95%) and C-rate (95%, 2 C/0.1 C) was obtained by controlling the process of heat treatment and PET addition. The mechanism of lithium-ion insertion was discussed based on effects of defective cavity and developed graphite interlayer.

리튬 이온 전지의 양극과 음극 사이에 물리적인 층을 만들어주는 분리막은 분리막의 품질에 따라 리튬 이온 전지의 성능을 결정함에 따라 많은 관심을 받고 있다. 일반적으로 전기화학적 안정성과 적절한 역학적 강도를 갖고 있는 폴리에 틸렌과 폴리프로필렌으로 구성된 다공성 막이 리튬 이온 전지의 분리막으로 사용된다. 하지만 폴리에틸렌과 폴리프로필렌의 낮은 열 저항성과 젖음성으로 인해 리튬 이온 전지의 잠재력을 충분히 끌어내지 못한다. 녹는점 이상의 온도에 도달하게 되면 분리막의 구조가 변형되고 리튬 이온 전지는 단락된다. 분리막의 낮은 젖음성은 낮은 이온전도도와 부합하고, 이는 전지의 저항을 상승시킨다. 이러한 폴리에틸렌과 폴리프로필렌 분리막의 단점을 극복하고자 이중 전기방사방법, 코팅 층 도포 방법, 코어 셸 구조 형성 방법, 제지법 등 여러 가지 방법들이 연구되었다. 언급된 방법들로 합성된 분리막들은 열 저항성과 젖음성이 크게 향상되었고 유연성과 인장 강도 같은 역학적 특성도 향상되었다. 본 리뷰 논문에는 각기 다른 방법으로 형성된 리튬 이온 전지의 분리막에 대해서 다루고 있다.

The improvement of heat transfer in water cooling passage of lithium-ion battery is numerically studied by employing trapezoidal vortex generators. Battery Design StudioⓇ software is used for modeling electro-chemical heat generation in the battery. The conjugated heat transfer is analyzed with the commercial package STAR-CCM+ in terms of inlet flow velocities. The result shows that vortex generator enhances the convective heat transfer by developing thermal boundary layers and secondary flows in downstream, which results in reducing the average temperature of the battery by about 1℃. The heat transfer is enhanced for the whole inlet velocity, while the pressure loss sharply increases at more than inlet velocity of 0.1m/s. The optimum inlet velocity is around 0.1m/s for in terms of the heat transfer and pressure loss.