Fundamental aspects of creating passivation layers for corrosion resistance in nuclear engineering applications, specifically the ability to form complete layers versus porous ones, are being explored in this study. Utilizing a laser ablation technique, 1,064 nm fire at 10 Hz with 60 pulses per shot and 0.5 mm between impact points, aluminum samples are treated in an attempt to create a fully formed passivation layer that will be tested in a LiCl-KCl eutectic salt. By placing these samples into an electrochemical environment mimicking a pyroprocessing system, corrosion rates, resistances and material characteristics are tested for one week and then compared between treated and untreated samples. In initial testing, linear sweep voltammetry indicates corrosion current density for the untreated sample at −0.038 mA·cm−2 and treated samples at −0.024 mA·cm−2 and −0.016 mA·cm−2, respectively. This correlates to a control sample corrosion rate of −0.205 mm·yr−1 and treated rates of −0.130 mm·yr−1 and −0.086 mm·yr−1 for samples 1 and 2. In addition, electrochemical impedance spectroscopy circuits show application of a longer-lasting porous passivation layer on the treated metal, compared to the naturally forming layer. However, the current technique fails to create a uniform protection layer across the sample.

Molten salt reactor (MSR) uses fluoride or chloride based molten salt as a coolant of the system, and fuel materials are dissolved in the molten salt, therefore it can be act as both coolant and nuclear fuel. A few issues have arisen from early-stage research and development program of MSR from Oak Ridge National Laboratory, including corrosion of structural materials and fission product management. For investigating the effect of additives on corrosion of structural materials, Mg(OH)2 and MgCl2*6H2O are added into the NaCl-MgCl2 eutectic salt. Prepared chloride salt is injected into the autoclave in the glove box, as well as corrosion coupons for candidate structural materials for molten chloride salt reactor, SS316, Alloy 600, and C-276 are also prepared. The temperature is set as 700°C. After 500 h corrosion experiment, the samples are taken out from the autoclave, and they are analyzed with scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS). SS316 samples show weight loss with all salt conditions, while Alloy 600 and C-276 show weight gain after the corrosion experiment.

Molten salt is one of the promising medium materials for molten salt reactors and energy storage systems. Molten salt is advantageous for better physical properties such as low melting point and high boiling point, high energy capacity, high thermal conductivity, and high thermal stability than other medium materials such as water or liquid metals. However, the corrosivity of the molten salt is one of the main factors that disturbs the various applications of the molten salt. On the other hand, metallic 3-D printing technologies have developed by leaps and bounds over the past 20 years and show potential for use in cutting-edge industries such as aerospace and military purposes. However, the biggest problem of 3-D printed products is that the mechanical and physical properties are very weak along the laminated plane that was generated during the manufacturing process. In particular, other research showed that corrosion is vulnerable through the laminated surface, and corrosion along the laminated plane is not completely mitigated through a general heat treatment process although the microstructure of the surface is evaluated to be partially mitigated by the heat treatment. In this study, molten salt corrosion behaviors of simple Ni-based alloy with a composition of 80Ni- 20Cr were analyzed. Ni-based alloys were fabricated by casting and 3-D printing, and some of the 3-D printed specimens were thermally treated at 1,273 K for 1 hour to examine the effects of heat treatment on corrosion behaviors. In molten eutectic NaCl-MgCl2 melts at 973 K, Ni-based alloys were corroded for 1, 3, 7, and 28 days and their microstructural changes were analyzed by SEM-EBSD-EDS and OM. The corrosion behaviors of the alloy were also evaluated by the salt composition measured with ICPOES. 3-D printed alloy with post-treatment showed more resistivity to the molten salt corrosion than as-fabricated 3-D printed alloy. However, the corrosion rate of the 3-D printed specimen after heat treatment was still higher than that made by casting.

In molten salt reactor (MSR), liquid fuel integrated with the molten salt coolant is used to improve the safety, resulting in the prevention of the loss-of-coolant accident (LOCA) that can occur in a pressurized water reactor (PWR). Because the structural materials used in MSRs are directly contacted with liquid fuel for a long time, they must have excellent corrosion resistance to the molten salt. Therefore, to examine the corrosion rates for Ni-based alloys in the molten salt, the corrosion experiments for alloy 600, alloy 617, and Hastelloy N were performed under LiCl molten salt at 635°C for 100 h in a glove box under Ar environment. Through a weight loss method for the three Nibased coupons before and after the corrosion tests, we evaluated their corrosion rates. Based on the results of weight loss for each alloy, we confirmed that Hastelloy N has the excellent corrosion resistance compared to the other alloys. Furthermore, the changes in the crystal structure and surface morphology with elemental distribution for the three alloys by corrosion in LiCl molten salt were analyzed, showing the variation in surface topography and the decrease in Cr element after corrosion experiments for all coupons.

A molten salt reactor (MSR) is a conceptual nuclear reactor that uses molten salt with liquid fuel as its primary coolant. Based on the thermophysical and neutronic properties, MSR has advantages such as high efficiency, safety, combustion of transuranic (TRU) elements, and availability of miniaturization and on-power refueling. Various research on MSR such as system development, neutronic analysis, material development, and molten salt property analysis has been conducted, but the biggest problem is the molten salt corrosion. The molten salt corrosion on structural materials can be explained by two processes; electrochemical and chemical reactions. The reduction of oxidative ions such as fuel and TRU elements is one of the major causes of molten salt corrosion. Contamination by humidity and oxygen is also known as the accelerating factor of molten salt corrosion. Also, molten salt corrosion behaviors on structural material deteriorate when dissimilar alloys are introduced in the molten salt system. Various techniques to mitigate molten salt corrosion in fluoride system has been developed, but these are not well-verified in chloride system. In this research, various methodologies to mitigate molten salt corrosion are studied. The corrosion behaviors of 80Ni-20Cr alloy in molten eutectic NaCl-MgCl2 salt at 973 K are analyzed with various applications such as salt purification, sacrificial metal injection, and salt redox potential control. Oxygen and water impurities that can accelerate molten salt corrosion have been removed by electrochemical and chemical methods; Applying the reduction potential for H+/H2 and oxidation potential for O2-/O2, introducing HCl and CCl4 gas, and introducing the metallic Cr and recovering the ionized Cr. Corrosion acceleration/deceleration effects were analyzed when introducing the reducing reagent such as Mg and Nb or oxidizing reagent such as metallic Mo and the effect of inert metallic element (W) was also investigated. The salt potential was controlled by applying the potential to the salt and adjusting the Eu3+/Eu2+ ratio.

In this study, molten salt experiments were performed using a multi-purpose molten salt experimental loop to evaluate the corrosion and thermodynamic properties of the molten salt. The multi-purpose molten salt experimental loop is made of 1-inch austenitic 316 stainless steel, and 1/4-inch austenitic 316 stainless steel tubes were welded on the surface of a 1-inch pipe to measure temperatures of molten salt. During the experiment, the molten salt leaked due to corrosion of the welded part of the 1/4-inch tube connected to the 1-inch pipe. Therefore, the cause of corrosion damage of the leaked welded part was analyzed. The effect of NaCl-MgCl2 salt selected as the molten salt on corrosion failure was considered. And based on the operation data of molten salt experiments, the time of occurrence of the issue was estimated. Lastly, the cause of corrosion failure was estimated by comparing and analyzing the pipe shape before and after failure using SEM-EDS.

A molten salt reactor (MSR) has considerably attracted attention due to its several advantages for the safety and efficiency over the light water reactors. Because the structural material in MSR is contacted with high-temperature liquid fuel during long-term, the excellent material for corrosion resistance is required to be applied in MSR. In this study, we evaluated the corrosion resistance for alloy 600 and 617, which are the nickel-based materials, in KCl molten salt at 800ºC for 100 h under Ar atmosphere containing less than 1 ppm of moisture and oxygen. After the corrosion experiments of alloy 600 and 617, the amount of the weight loss for them caused by the KCl molten salt were determined. In addition, the variation in the crystal structure, surface morphology, and elemental distribution was examined using X-ray diffraction and scanning electron microscopy equipped with energy dispersive X-ray spectroscopy.

The aim of this review is to communicate some essential knowledge of the underlying mechanism of the corrosion of structural containment alloys during molten salt reactor operation in the context of prospective online monitoring in future MSR installations. The formation of metal halide species and the progression of their concentration in the molten salt do reflect containment corrosion, tracing the depletion of alloying metals at the alloy salt interface will assure safe conditions during reactor operation. Even though the progress of alloying metal halides concentrations in the molten salt do strongly understate actual corrosion rates, their prospective 1st order kinetics followed by near-linearly increase is attributed to homogeneous matrix corrosion. The service life of the structural containment alloy is derived from homogeneous matrix corrosion and near-surface void formation but less so from intergranular cracking (IGC) and pitting corrosion. Online monitoring of corrosion species is of particular interest for molten chloride systems since besides the expected formation of chromium chloride species CrCl2 and CrCl3, other metal chloride species such as FeCl2, FeCl3, MoCl2, MnCl2 and NiCl2 will form, depending on the selected structural alloy. The metal chloride concentrations should follow, after an incubation period of about 10,000 hours, a linear projection with a positive slope and a steady increase of < 1 ppm per day. During the incubation period, metal concentration show 1st order kinetics and increasing linearly with time1/2. Ideally, a linear increase reflects homogeneous matrix corrosion, while a sharp increase in the metal chloride concentration could set a warning flag for potential material failure within the projected service life, e.g. as result of intergranular cracking or pitting corrosion. Continuous monitoring of metal chloride concentrations can therefore provide direct information about the mechanism of the ongoing corrosion scenario and offer valuable information for a timely warning of prospective material failure.

A study on the corrosion behavior of Inconel alloys and Incoloy 800H in molten salt of LiCl-Li2O was investigated at 650˚C for 24-312 hours in an oxidation atmosphere. The order of the corrosion rate was Inconel 600< Inconel 601< Incoloy 800H< Inconel 690. Inconel 600 showed the best performance suggesting that the content of Fe, Cr and Ni are the important factor for corrosion resistance in hot molten salt oxidation conditions. The corrosion products of Inconel 600 and Inconel 601 were Cr2O3 and NiFe2O4, In case of Inconel 690, a single layer of Cr2O3 was formed in the early stage of corrosion and an outer layer of NiFe2O4 and inner layer of Cr2O3 were formed with an increase of corrosion time. In the case of Incoloy 800H, Cr2O3 and FeCr2O4 were observed. Most of the outer scale of the alloys was observed to be spalled from the results of the SEM analysis and the unspalled scale which adhered to the substrate was composed of three layers. The outer layer, the middle one, and the inner one were Fe, Cr, and Ni-rich, respectively. Inconel 600 showed localized corrosion behavior and Inconel 601, 690 and Incoloy 800H showed uniform corrosion behavior. Ni improves the corrosion resistance and too much Cr and/or Fe content deteriorates the corrosion resistance.

The electrolytic reduction of a spent oxide fuel involves liberation of the oxygen in a molten LiCl electrolyte, which is a chemically aggressive environment that is too crosive for typical structural materials. Therefore, it is essential to choose the optimum material for the process equipment for handling a molten salt. In this study, the corrosion behavior of pyro-carbon made by CVD was investigated in a molten LiCl-Li2O salt under an oxidation atmosphere at 650˚C and 750˚C for 72 hours. Pyro-carbon showed no chemical reactions with the molten salt because of its low wettability between pyro-carbon and the molten salt. As a result of XRD analysis, pyro-carbon exposed to the molten salt showed pure graphite after corrosion tests. As a result of TGA, whereas the coated layer by CVD showed high anti-oxidation, the non-coated layer showed relatively low anti-oxidation. The stable phases in the reactions were C(S), Li2CO3(S), LiCl(l), Li2O at 650˚C and C(S), LiCl(l), Li2O(S) at 750˚C. Li2CO(S) was decomposed at 750˚C into Li2O(S) and CO2(g).

Incoloy 800H, KSA (Kaeri Superalloy)-6, Inconel 600 및 Hastelloy C-276 합금의 용융염에서의 부식거동을 650~850˚C 온도범위에서 조사하였다. LiCl-Li2O혼합용융염에서의 부식은 Li2O에 의한 염기성 용해 기구에 의해 진행되며, 부식속도가 LiCl에서보다 훨씬 빠르게 나타났다. 혼합용융염 LiCl-Li2O에서는 Ni기 합금의 부식속도가 Fe기 합금보다 빠르고, Mo와 W의 함량이 높은 Hastelloy C-276이 가장 빠른 부식속도를 나타내었다. 용융염 LiCl에서는 LiCrO2의 단일 부식층이 형성되고, LiCl-Li2O 혼합용융염에서는 산화물과 Ni의 2상구조의 다공성 부식층이 형성되었다.

LiCl 및 LiCl/Li2O 용융염분위기에서 오스테나이트 스테인레스강, SUS 316L과 SUS 304L의 부식특성을 650­~850˚C 온도범위에서 조사하였다. SUS 316L과 304L의 부식층은 외부 Li(CrFe)O2와 내부 Cr2O3의 2층 구조를 형성하였다. LiCl 용융염중에서는 균일한 부식충이 형성되지만, LiCl/Li2O 혼합용융염중에서는 균일한 부식충 형성외에 업계부식이 발생되는 것을 알 수 있었다. 750˚C까지 온도 증가에 따른 부식속도의 증가속도는 느리고, 750˚C 이상에서는 부식속도가 급격히 증가하였다. 용융염분위기에서 SUS 316L은 SUS 304L에 비하여 부식속도가 느려셔 보다 좋은 내식성을 나타내였다.

용융탄산염 연료전지는 650˚C의 부식성이 강한 용융탄산염내에서 작동되므로, 분리판 재료로 사용되고 있는 316L 스테인레스강의 부식은 용융탄산염 연료전지의 수명을 단축시키는 주요한 원인이다. 특히 분리판 wet-seal부의 부식은 보다 심각한 것으로 알려져 있다. 이를 해결하기 위하여 AI계 합금이 피복재료로 사용되어 왔지만, 본 연구에서는 보다 우수한 분리판 wet-seal부의 내식 피복재료 개발을 위하여 피복재료인 NiAI 합금에 산화 활성화 원소인 yttrium을 최고 1.5 at%까지 첨가하였다. 650˚C의 용융탄산염내에서 yttium 함량에 따른 NiAI/Y 합금의 침지부식실험 및 분극실험을 통하여 내식성을 평가하고 부식 억제를 위해 가장 적절한 NiAI/Y 피복 재료의조성을 결정한 결과 최소의 yttrium 조성은 0.7 at% 임을 알 수 있었다.