과거 지진 발생 시 구조요소에 비해 비구조요소에서 더 많은 피해가 발생하였다. 비구조요소의 손상은 건물 및 시설의 기능에 영향을 줄 뿐만 아니라 인명피해를 유발할 수 있다. 건축물 내진설계 기준에서는 피난경로상의 비구조요소는 내진설계 또는 검토가 필요하다. 국내에서는 경주지진 이후 피난경로에 위치할 수 있는 천장 시스템의 내진성능 검증이 활발히 진행되고 있다. 그러나 옥외 계단, 문 등에 설치되는 캐노피 시스템의 내진설계 및 검증은 미흡한 실정이다. 지진으로 인해 캐노피가 위치유지를 하지 못하여 탈락 하거나 손상될 경우, 피난경로가 차단되어 인명피해로 이어질 수 있으므로 내진설계 및 내진성능을 평가할 필요가 있다. 따라서 본 연구에서는 모듈형 캐노피 시스템을 개발하고, 주요 요소에 대한 구조실험을 수행하였으며, 기존의 캐노피 시스템과 그 성능을 비교분 석 하였다.

해운 산업은 탄소 배출 저감을 위한 다양한 기술적 해결책을 모색하고 있으며, 그중 암모니아(NH3)는 차세대 무탄소 연료로 각 광받고 있다. 암모니아는 이산화탄소(CO2)를 배출하지 않으며, 기존 인프라를 활용해 대규모 운송 및 저장이 가능하다는 장점이 있다. 본 연구는 암모니아를 수소(H2)로 개질하여 연료전지에 공급하고, 이를 통해 전력을 생산하는 하이브리드 전기 추진 시스템의 성능을 평가하 였다. 암모니아-수소 개질기, 수소 연료전지, 배터리로 구성된 이 시스템은 친환경적인 추진 방식이다. 경사 시험(Heel test)은 선박이 실제 항해 중에 겪을 수 있는 10도 경사 상황에서 시스템이 안정적으로 작동하는 평가하기 위해 수행되었다. 시험 결과, 암모니아 개질기는 경사 조건에서도 안정적으로 수소를 생산하였다. 연료전지와 배터리가 결합된 하이브리드 시스템은 부하 변동 상황에서도 효율적으로 전력을 관리하고 안정적인 전력 공급을 유지했다. 특히 경사 상태에서도 시스템 성능 저하 없이 연료전지와 배터리 전력, 전류, 전압의 상호작용이 원활하게 이루어졌음을 확인할 수 있다. 본 연구는 향후 친환경 선박의 핵심 기술로 자리 잡을 수 있는 암모니아 기반 추진 시스템의 안정 성과 성능을 실험적으로 검증하였다는 점에서 그 의미가 있으며, 따라서 본 연구 결과는 해운 산업에서 암모니아 기반 추진 시스템의 사용 화 가능성을 높이는 중요한 기초 자료를 제공할 것으로 기대된다.

This study is about the evaluation for shock-proof performance of the system, elastically support the low accumulator of the naval artillery against underwater explosion, using DDAM. For the evaluation, the shock analysis procedure using DDAM, supported by MSC/NASTRAN, was briefly described. In addition, in order to perform the shock analysis, the elastic support system was modeled as a finite element. The shock analysis of the elastic support system was performed by selecting the analysis frequency range so that reliable results can be obtained. Finally, the shock-proof performance of the system was evaluated by comparing the shock analysis results with the properties of the elastic support system.

본 논문에서는 다양한 기상 조건에서 시인성과 내구성을 향상시키도록 설계된 도로 표시용 UV 경화 코팅 시스템 개발을 위해 수행한 연구의 결과를 나타내었다. 제조된 UV 코팅을 사용해 차선 표시의 재귀반사도와 내마모성을 강화하고 포장가속시험(APT), 휠 트래킹 내구성 테스트 등 다양한 테스트를 통해 성능을 평가하였다. 이 결과를 바탕으로 도로 안전을 위한 야간 시인성 및 미끄럼을 개선하 고자 한다.

이 연구에서는 CFRP 케이블의 압착형 정착장치의 강종에 따른 피로성능을 평가하였다. 실험결과, CFRP 케이블 압착형 정착시스템은 정착장치의 강종에 상관없이 도로교설계기준의 포스트텐션용 정착 구에 대한 피로시험 조건을 만족시켰다. 그러나 피로시험이후 인장성능 실험에서 SM45C 강종의 정착 장치는 최대내력 도잘전에 케이블과 정착장치 사이에서 미끄러짐이 발생하였으며, 듀플렉스 강종의 정 착장치는 최대 내력 도달과 동시에 CFRP 케이블이 파단되었다.

As a means to activate eco pastoral system in alpine grassland, the government can consider public pastures, which are currently unused, to scale them up into public ranches. Depending on ownership and operation, four management models proposed as follows: 1) Government-Owned and Operated with Balanced Profit and Loss 2) Government-Owned and Operated with Revenue Generation 3) Government-Owned but Privately Operated by Outsourced to Professional Manager 4) Full Privatization (Ownership and Operation by Private Individuals). The study outlined above proposes four management models for the activation of eco pastoral system in alpine grassland. It also suggests methods for the selection and performance evaluation of manager to establish a profitable structure. Additionally, the research provides management methods for the conservation of grazing ecology in pastoral ecosystems. Particularly, the adaptation of tools commonly used in South Korean business sector for the selection and performance evaluation of manager within the system of the proposed management models. This aspect is deemed valuable as it aligns these tools with the specific characteristics of eco pastoral system in alpine grassland, contributing not only to the effective implementation of the models but also to the enhancement of the revenue structure.

PURPOSES : The number of snowfall and the amount of snowfall are gradually increasing, and due to the characteristics of Seoul, which has a lot of traffic, it is difficult to respond quickly with a snow removal method that relies on snow removal vehicles. Therefore, it is necessary to develop an IoT based eco-friendly snow removal system that can respond to unexpected heavy snow in winter. In this study, the low temperature operation and snow removal performance of the IoT road condition snow removal detector and the snow removal system using CNT and PCM are evaluated in the climatic environment chamber. METHODS : To make artificial snow, it consists of an climatic environment chamber that can simulate a low temperature environment and equipment that can supply compressed air and cold water. Depending on the usage characteristics of the climatic environment chamber, use an air-water type snow maker. In order to make artificial snow, wet temperature, which takes into account the actual air temperature and the amount of moisture in the air, acts as the most important variable and is suitable for making snow, below –1.5 ℃. The lower the water temperature, the easier it is to freeze, so the water source was continuously supplied at 0 ℃ to 4 ℃. One of the two different pipes is connected to the water tank to supply water, and the other pipe is connected to the compressor to supply high-pressure air. Water is dispersed by compressed air in the form of many small droplets. The sprayed microscopic water particles freeze quickly in the low temperature environmental climatic chamber air and naturally fall to the floor, forming snow. Based on the KS C IEC 60068-2-1 cold resistance test standard, an integrated environmental test procedure was prepared to apply to IoT-based snow removal systems and performance evaluation was performed accordingly. The IoT based eco-friendly snow removal system is needed to in winter, so visual check and inspect the operation at the climatic chamber before setting up it to the actual site. In addition, grid type equipment was manufactured for consistent and reliable snow removal performance evaluation under controlled environmental conditions. RESULTS : The IoT-based eco-friendly snow removal system normally carried out the task of acquiring data and images without damaging the appearance or freezing in a low temperature environment. It showed clear snow removal performance in areas where PCM and CNT heating technology were applied to the concrete slab. This experiment shows that normal snow removal tasks can be carried out in low temperature environments in winter. CONCLUSIONS : The integrated environmental test procedures and grid type evaluation equipment are applied to low temperature operation and snow removal performance evaluation of snow removal systems. In the climatic environment chamber, where low temperature environments can be simulated, artificial snow is created regardless of the season to derive quantitative experimental results on snow removal performance. PCM and CNT heating technology showed high snow removal performance. The system is expected to be applied to road site situations to preemptively respond to unexpected heavy snow in winter.

Recently, BNS (Best System) developed a system for evaluation and classification of soil and concrete wastes generated from nuclear power plant decommissioning. It is composed of various modules for container loading, weight measurement, contamination evaluation, waste classification, stacking, storage and control. The contamination evaluation module of the system has two sub modules. One is for quick measurement with NaI (Tl) detector and the other is for accurate measurement with HPGe detector. The container used at the system for wastes handling has capacity of 100 kg and made of stainless steel. According to the measurement result of Co-60 and Cs-137, the waste is classified as waste for disposal or waste for clearance. Performance of the system was demonstrated using RM (Reference Material) radiation source. This year, necessity of system improvement was suggested due to revised operation requirements. So, the system should show throughput of more than 1 ton/hr and Minimum Detectable Activity (MDA) of less than 0.01 Bq/g (1/10 of criteria for regulatory clearance) for Co-60 and Cs-137. And soil waste become main target of the system. For this, the container used for soil waste handling should have capacity of 200 kg. As a result, material for the container need to be changed from stainless steel to plastic or FRP (Fiber Reinforced Plastics). And large area detector should be introduced to the system to enhance processing speed of the system. Additionally, container storage rack and conveyor system should be modified to handle 200 kg capacity container. Finally, moving path of the container will be redesigned for enhanced throughput of the system. In this paper, concept development of the system was suggested and based on that, system development will be followed.

Economical radioactive soil treatment technology is essential to safely and efficiently treat of high-concentration radioactive areas and contaminated sites during operation of nuclear power plants at home and abroad. This study is to determine the performance of BERAD (Beautiful Environmental construction’s RAdioactive soil Decontamination system) before applying magnetic nanoparticles and adsorbents developed by the KAERI (Korea Atomic Energy Research Institute) which will be used in the national funded project to a large-capacity radioactive soil decontamination system. BERAD uses Soil Washing Process by US EPA (402-R-007-004 (2007)) and can decontaminate 0.5 tons of radioactive soil per hour through water washing and/or chemical washing with particle size separation. When contaminated soil is input to BERAD, the soil is selected and washed, and after going through a rinse stage and particle size separation stage, it discharges decontaminated soil separated by sludge of less than 0.075 mm. In this experiment, the concentrations of four general isotopes (A, B, C, and D which are important radioisotopes when soil is contaminated by them.) were analyzed by using ICP-MS to compare before and after decontamination by BERAD. Since BERAD is the commercial-scale pilot system that decontaminates relatively large amount of soil, so it is difficult to test using radioactive isotopes. So important general elements such as A, B, C, and D in soil were analyzed. In the study, BERAD decontaminated soil by using water washing. And the particle size of soil was divided into a total of six particle size sections with five sieves: 4 mm, 2 mm, 0.850 mm, 0.212 mm, and 0.075 mm. Concentrations of A, B, C, and D in the soil particles larger than 4 mm are almost the lowest regardless of before and after decontamination by BERAD. For soil particles less than 4 mm, the concentrations of C and D decreased constantly after BERAD decontamination. On the other hand, the decontamination efficiency of A and B decreased as the soil particle became smaller, but the concentrations of A and B increased for the soil particle below 0.075 mm. As a result, decontamination efficiency of one cycle using BERAD for all nuclides in soil particles between 4 mm and 0.075 mm is about 45% to 65 %.

강진에 대한 다양한 비선형 거동을 하는 부재요소들로 이루어진 교량시스템의 현재까지의 일반적인 지진취약도 평가방법은 부재- 수준에서 평가하는 것이다. 본 연구의 목적 부재-수준의 지진취약도 평가결과로부터 구조시스템을 대표하는 시스템-수준의 지진취 약도 평가방법을 개발하는 것이다. 교량의 지진 거동을 일반적으로 교축방향과 교축직각방향으로 구분하기 때문에 본 연구에서도 시 스템-수준 지진취약도를 두 방향에 대하여 구분해 평가하였다. 길이 방향에 대한 부재-수준의 지진취약도평가는 교각, 교량받침, 충 돌, 교대, 낙교에 대하여 수행하였다. 교축직각 방향에 대해서는 충돌, 교대, 낙교의 손상이 영향을 주지 않으므로 부재-수준의 지진취 약도평가는 교각과 교량받침에 대하여만 수행하였다. 다양한 구조부재의 비선형모델을 이용한 지진해석은 OpenSEES 프로그램을 사용하여 수행하였다. 시스템-수준의 지진취약도는 부재-수준 사이의 손상이 직렬연결이라고 가정하고 평가하였다. 교각의 손상이 다른 부재-수준의 손상보다 시스템-수준의 지진취약도에 지배적인 영향을 주는 것을 알 수 있었다. 다시 말하면 가장 취약한 부재-수 준의 지진취약도가 시스템-수준의 지진취약도에 가장 지배적인 영향을 주는 것을 의미한다.

In-situ gamma spectrometer with mobile equipment can be used for rapid determination of radioactivity in the environment within a very short interval. 2”×2” NaI(Tl) scintillator are used to build a mobile radiation measurement system (called as Monitoring of Ambient Radiations of KAERI for Backpack, MARK-B3) with a signal processing unit, and GPS and interface units to a PC for wireless controlling system. Development of the survey system is to measure ambient gamma-ray spectrometry for estimating ground radioactivity and radiation dose in the environment. The ambient dose rate is estimated using G-factor method. For determination of G-factor, we conducted MCNP simulations in assumptions of various incident photons into the detector system. And the scintillator was exposed to Cs-137 source in the range of 1- 300 mGy/hr. Calculated dose rates for different simulation results were compared to the irradiated dose rate to derive correction factor of G-factor. To evaluate performance of the MARK-B3, in-situ gamma spectrometry was conducted in Jeju island.

This study sought to conduct a fundamental investigation in order to test and evaluate the thermal performance of an aluminum stick curtain wall system. In terms of the thermal performance index, the infiltration rate of air tightness, thermal transmittance of the heat insulation property and temperature difference ratio of condensation resistance were experimentally measured. The research process can be divided into three parts. First of all, a database for the test report of the curtain wall was compiled and existing design criteria with respect to the evaluation method and standard of transparent building components such as curtain wall, window and door were analyzed to produce the specimens. Secondly, four different types of curtain wall specimens were created through investigating the curtain wall database. Thirdly, standard tests of thermal performance were carried out for airtightness, thermal performance and condensation resistance. As a result, the curtain wall specimens with low-e triple glazing covered by an aluminum capture system showed high thermal performance compared to other curtain wall specimens including low-e triple glazing with a 4-sided structural sealant glazing system. Air tightness of all types of curtain wall specimens satisfied level 1 standard for air tightness. It was found that a curtain wall which consists of a one track frame has difficulties meeting the residential standard of thermal performance with regard to thermal transmittance and condensation resistance.

Failure to comply with the performance test requirements for the centrifugal pumps at power plants often results in performance dissatisfaction as a result of field tests. This study proposed a method of reducing the uncertainty of the field test results by evaluating the systematic error in the measurement system caused by failure to follow the test requirements using the computational fluid dynamics(CFD) technique. As a result of the evaluation of the systematic error and reflecting it in the performance test data, it was confirmed that the error occurred at a constant rate with respect to the flowrate and that the pump, which showed a difference in performance actually had the same performance.

Seoul has installed mechanical air filters in the heating, ventilation, and air conditioning (HVAC) systems of city buses to improve their indoor air quality since late 2019. We evaluated particle removal efficiencies of the filter in a wind tunnel, and clean air delivery rates (CADRs) of the systems and a household air purifier in the buses, following the test standards. The filter showed the efficiencies of 91% and 97.6%, 88% and 97.9%, and 78% and 95.2% for 0.35 μm particles and PM2.5 at 1.0m/s, 1.5m/s, and 2.0m/s, respectively. The efficiencies rose with an increase in the particle size and the filters had a minimum efficiency reporting value (MERV) rating of 15. The CADRs for PM2.5 and flow rate of the systems were 12.7m3/min and 17.9m3/min, 16.6m3/min and 25.4m3/min, 18.7m3/min and 33.6m3/min, and 23.3m3/min and 47.1m3/min on the operation mode of 1, 2, 3, and 4, respectively. The CADRs of the systems were 3.8-7.1 times higher than those of the air purifier, but single-pass removal efficiencies of the former were 0.56-0.81 lower than those of the latter.

For the peaceful use of nuclear energy, the international community has devoted itself to fulfilling its obligations under the Safeguards Agreement with IAEA. In this regard, uranium in a radioactive waste drum should be analyzed and reported in terms of mass and 235U enrichment. In order to characterize radioactive wastes, gamma spectroscopy techniques can be effectively applied. In the case of high-resolution gamma spectroscopy, because an HPGe detector can provide excellent energy resolution, it can be applied to analyze a mixture having a complicated isotopic composition. However, other substances such as wood, concrete, and ash are mixed in radioactive waste with various form factors; hence, the efficiency calibration is difficult. On the other hand, In Situ Object Counting System (ISOCS) has a capability of efficiency calibration without standard materials, making it possible to analyze complex radioactive wastes. In this study, the analysis procedure with the ISOCS was optimized for quantification of radioactive waste. To this end, a standard radioactive waste drum at KEPCO NF and low-level radioactive waste drums at Korea Radioactive Waste Agency (KORAD) were measured. The performance of the ISOCS was then evaluated by Monte Carlo simulations, Multi-Group Analysis for Uranium (MGAU) code, and destructive analysis. As a result, the ISOCS showed good performance in the quantification of uranium for a drum with the homogenized simple geometry and long measurement time. It is confirmed that the ISOCS gamma spectroscopy technique could be used for control and accountancy of nuclear materials contained in a radioactive waste drum.

A pump-type eDNA filtering system that can control voltage and hydraulic pressure respectively has been developed, and applied a filter case that can filter out without damaging the filter. The filtering performance of the developed system was evaluated by comparing the eDNA concentration with the conventional vacuum-pressured filtering method at the catchment conduit intake reservoir. The developed system was divided into a voltage control (manual pump system) method and a pressure control (automatic pump system) method, and the pressure was measured during filtering and the pressure change of each system was compared. The voltage control method started with 65 [KPa] at the beginning of the filtering, and as the filtering time elapsed, the amount of filtrate accumulated in the filter increased, so the pressure gradually increased. As a result of controlling the pressure control method to maintain a constant pressure according to the designed algorithm, there was a difference in the width of the hydraulic pressure fluctuation during the filtering process according to the feedback time of the hydraulic pressure sensor, and it was confirmed that the pressure was converged to the target pressure. The filtering performance of the developed system was confirmed by measuring the eDNA concentration and comparing the voltage control method and the hydraulic control method with the control group. The voltage control method obtained similar results to the control group, but the hydraulic control method showed lower results than the control group. It is considered that the low eDNA concentration in the hydraulic control method is due to the large pressure deviation during filtering and maintaining a constant pressure during the filtering process. Therefore, rather than maintaining a constant pressure during filtering, it was confirmed that a voltage control method in which the pressure is gradually increased as the filtrate increases with the lapse of filtering time is suitable for collecting eDNA. As a result of comparing the average concentration of eDNA in lentic zone and lotic zone as a control group, it was found to be 96.2 [ng μL-1] and 88.4 [ng μL-1l], respectively. The result of comparing the average concentration of eDNA by the pump method was also high in the lentic zone sample as 90.7 [ng μL-1] and 74.8 [ng μL-1] in the lentic zone and the lotic zone, respectively. The high eDNA concentration in the lentic zone is thought to be due to the influence of microorganisms including the remaining eDNA.