In this study, two alignment methods were used to create a Fringe-Field Switching (FFS) mode liquid crystal device using an organic thin film (polyimide: PI) as an alignment layer. In addition, the electro-optical (EO) characteristics of the liquid crystal device manufactured in this way were investigated to evaluate the feasibility of mass production application of the technology. In general, the photo-alignment method using unpolarized ultraviolet rays can obtain a relatively low pretilt angle, so a liquid crystal device in FFS mode, which is a driving mode of the liquid crystal device that reflects the characteristics of liquid crystal alignment, was manufactured, and the liquid crystal has a high reactivity with the alignment film. Considering this, nematic liquid crystal (NLC) was used. In addition, in order to improve the misalignment, it was observed whether more stable orientation occurred by irradiating ultraviolet rays for an additional 1 to 3 hours in the aligned state. As a result of the experiment, it was found that NLC alignment occurs through a photodecomposition reaction caused by unpolarized UV irradiation oblique to the PI surface. In addition to the existing orientation method, UV irradiation was used to achieve a more stable orientation state and stable V-T curve and response characteristics. With liquid crystal alignment completed, more stable orientation characteristics and EO characteristics at the mass production level were obtained through additional UV irradiation for 3 hours. This method can further stabilize the orientation stability caused by existing UV irradiation through an additional process.

Nanoparticles are commonly used to avoid the opaque white color of TiO2 based sunscreen. However, a dispersing agent is typically required because of the tendency of the nanoparticles (NPs) to agglomerate. Stearic acid is one kind of dispersing agent often used for sunscreen products. However, according to the MSDS data sheet on stearic acid, stearic acid is highly hazardous to aquatic life and causes irritation on human skin. To avoid this problem, in this study a safer organic dispersing agent extracted from Korean seaweed has been studied to disperse TiO2 nanoparticles, and further use as an active agent in sunscreen products. The presence of phytochemicals in seaweed extract, especially alginate, can disperse TiO2 nanoparticles and improve TiO2 dispersion properties. Results show that seaweed extract can improve the dispersion properties of TiO2 nanoparticles and sunscreen products. Reducing the agglomeration of TiO2 nanoparticles improves sunscreen properties, by making it less opaque white in color, and increasing UV protection value. It was also confirmed that adding seaweed extract into sunscreen products had no irritating effects on the human skin, making it more desirable for cosmetics application.

본 연구에서는 단기간의 UV-A 조사가 시금치(Spinacia oleracea L.)의 생장과 생리활성물질에 미치는 영향을 평가 하였다. 시금치 묘는 200μmol·m-2·s-1 PPFD, white LED, 광 주기 12시간, 온도 20°C, 상대습도 70%, 이산화탄소 농도 500μmol·mol-1의 수직농장 모듈에서 재배되었다. 파종 후 5 주된 묘는 7일 동안 20W·m-2와 40W·m-2의 두 가지 에너지 수 준에서 연속적으로 UV-A(피크파장: 385nm) 조사한 후 생육 특성, 광합성 파라미터, 이미지 형광, 총 페놀 함량, 항산화도, 그리고 총 플라보노이드 함량을 분석하였다. 결과적으로, UV-A20W 처리는 시금치의 생체중과 건물중을 증가시켰다. 하지만, UV-A 처리구와 대조구 사이의 광합성 파라미터에는 유의한 차이가 나타나지 않았다. 광계Ⅱ의 최대양자수율 (Fv/Fm)은 모든 UV-A 처리에서 7일동안 지속적으로 감소했 다. 또한, UV-A20W 처리에서 식물체당 총 페놀 함량과 항산화 도는 처리 7일째 증대되었으며, 총 플라보노이드 함량은 처리 5일째부터 유의적으로 증가하였다. 이러한 결과는 UV-A LED 보광이 수직농장과 같은 폐쇄형 식물 생산 시스템에서 재배되는 시금치의 생장과 품질을 향상시킬 수 있음을 시사 한다.

본 연구는 축산물 생산 환경에서 오염 가능한 Aspergillus ochraceus와 Rhodotorula mucilaginosa를 저감하기 위하여 자외선과 유기산을 활용하여 그 효과를 구명하였다. 이를 위하여 각각의 균 현탁액(107-108 spores/mL)을 칼 표면에 1 mL 접종하고 37oC에 건조한 후 각각의 처리 조건에 활 용하였다. 먼저 유기산 효과를 구명하기 위하여 아세트산, 젖산, 구연산을 활용하였으며 적정 농도 선정을 위하여 0.5, 1, 2, 3, 4, 5%의 농도로 제조하였다. 그 결과 아세트 산의 경우 약 5 log, 젖산은 최대 2 log CFU/cm2 감소하 였으나, 구연산의 경우 1 log 이하로 미미한 수준이었다. 이에 따라 유기산 처리 효과를 더욱 극대화하기 위해 자 외선과의 복합처리를 진행하고자 하였다. 두 균주는 모든 유기산에서 90% 이상 감소하여 초기 균주와 비교하였을 때 유의적인 차이(P<0.05)를 보였으며 특히 4%의 젖산은 자외선(360 mJ/cm2)과 함께 처리하였을 때, 2 log CFU/cm2 이상 감소하였으며 같은 조건에서 아세트산은 5 log CFU/ cm2이상의 저감능을 보였다. 그러나 본 연구에서 사용한 4% 농도의 아세트산으로 제조할 경우 이취가 매우 심하여 작업자가 생산환경에서 사용하기에 어려움이 있다. 이 에 따라서 현장에 적용하기 위한 유기산과 자외선 최적 처리 조건은 4% 젖산 용액에 1분간 침지한 후 자외선을 20분 가량(360 mJ/cm2) 살균 처리하는 방법으로 선정하였 다. 최종적으로 유기산 세척 및 자외선 처리가 된 칼로 돼 지고기 절단 작업을 수행하였을 때, 현장 오염 수준의 진 균류 농도에서 작업 후 돼지고기 표면으로 이행되는 오염 량은 모두 불검출 되었다. 본 연구를 통하여 실험실 규모 뿐만 아니라 최종적으로 현장에서 살균된 도구를 활용하 여 작업 시 고기 표면까지 이행되는 교차오염을 방지할 수 있는 것으로 사료된다.

UV and O3 are materials used in the water treatment process, and many studies have been reported to remove organic matters, contaminants, and microorganisms. In this study, we were investigated effects of Chirnomidae (Chironomus flaviplumus, Chironomus riparius), which are contamination indicator species to exposure UV and O3 for the survival rate, body color change and gene expression response. The survival rate of C. flaviplumus exposed to UV decreased to about 70% after 24 hours, and C. riparius about 50%. There was no change in the survival rate of C. flaviplumus exposed to O3, and C. riparius decreased to 95% after 10 minutes of exposure, but there was no change during the subsequent exposure time. In addition, UV and O3 exposure to the two species in body color faded in a time-dependent. In the HSP70 gene expression, C. riparius showed an increase in expression after UV exposure compared to the control group, and a significant difference was shown 12 hours after exposure (P<0.05). C. flaviplumus exposed to O3 showed a relatively low expression compared to the control group, and showed a significant difference at 10 minutes and 1 hour after exposure (P<0.05). These results reported the ecotoxicological effects on Chironomidae according to UV and O3 exposure. Therefore, the results of this study can be used as basic data to understand the effects of UV and O3, which are disinfectants used in water treatment plants, on Chirnomidae entering plants. Key words: Chironomus flaviplumus, Chironomus riparius, UV, O3, acute toxicity, survival

Chelating agents like ethylenediaminetetraacetic acid (EDTA), diethylenetriaminepentaacetic acid (DTPA), and nitrilotriacetic acid (NTA) find extensive application in the removal of residual substances due to their high stability constants with a wide range of metal ions. They also play a crucial role in nuclear decontamination operations aimed at eliminating metallic radionuclides such as 60Co, 90Sr, and 239Pu. However, improper disposal of chelated radioactive waste can lead to significant increases in radionuclide migration rates from disposal sites. Therefore, it is imperative to comprehend the behavior of chelating agents under varying conditions, including pH, temperature, and metal ion concentrations. In this study, we present the results of a pH-dependent composition analysis of nickel-chelate complexes using UV-Vis spectrophotometry. Nickel (Ni) serves as an ideal metal ion for investigating its interactions with chelating agents due to its solubility over a wide pH range and high stability constants with all three chelating agents mentioned earlier. Initially, UV-Vis spectra of Ni-EDTA, Ni-DTPA, and Ni-NTA complexes were recorded at various pH levels. We assigned absorption maxima and compared our findings with existing literature on each Ni-chelate complex. Furthermore, we examined mixed samples of all three complexes, varying the pH to monitor changes in composition. The results and their implications will be presented in our poster presentation.

Most of the C-14 produced is in the organic form, generated as methane (14CH4), methanol (14CH3OH), formaldehyde (14CH2O), and formic acid (14CO2H2). When analyzing C-14, it is transformed into the form of 14CO2, and its concentration is determined using LSC. Typical examples include the wet oxidation method, the combustion or Pyrolysis. The wet oxidation method uses strong acids and involves repeated operations, which generates large amounts of acid waste and secondary radioactive waste. The combustion method uses high temperatures, which requires an oxygen device. Pyrolysis also requires high temperature in a vacuum and catalysts. Catalysts are expensive because they are platinum-based. To compensate for these shortcomings, a C-14 analysis method using UV irradiation was developed. In this study, 100 mL of distilled water mixed with formic acid (CO2H2), potassium persulfate (K2S2O8), and silver nitrate (AgNO3) was irradiated with a 320-390 nm UV lamp to conduct a CO2 production reaction experiment. The UV range was measured using a photometer (UV Power puck II). The beaker was made of quartz in 150 mL size with three inlets : a temperature measurement, a sample inlet, and a collection tube connector. We changed the UV lamp used from a 450 W halogen lamp to a 100 W LED, which has a lower temperature and is safer. As a result of the experiment, CO2 bubbles were generated in the collection tube, due to the UV irradiation react, which uses oxidizer and catalysts. The maximum temperature of the solution irradiated with the LED UV lamp was less than 56°C. It confirmed the rate of bubble generation changed depending on the lamp distance, the amount of sample, oxidizer, and catalyst. In an experiment to confirm the reaction caused by heat, it was found that although a reaction occurred due to heat, the reaction was significantly lower than when using a UV lamp. The reproducibility experiment was conducted three times in total under the same conditions. It showed the same pattern. In the future, we plan to select mock samples, collect 14CO2 in Carbo- Sorb, and analyze them using LSC. The results of this research will be used as a technology to recover C-14 more safely and efficiently and will also be used to expand its application to the treatment of other wastes such as waste liquid and waste resin through simulated samples.

This study demonstrated a rapid and simple method for the determination of seven anions including halides and oxyhalides from the KURT underground water sample by capillary electrophoresis with UV detection. In nuclear waste disposal, some anions such as iodine, selenium, and technetium have been of great concern due to its high mobility and toxicity with a long half-life. It has been needed for a reliable analysis of anionic speciation because the high mobility of anions is easily affected by environmental conditions especially pH and salinity of underground water. Here this project is to develop a fast separation of seven anions including iodide, iodate, and selenite using capillary electrophoresis. The electroosmotic flow (EOF) was suppressed using a poly (ethyleneglycol) -coated capillary (DB-WAX capillary). As a result, anions migrated depending on their mobility under a reverse polarity condition (-15 kV) and the analysis time was within 15 min. UV detection was used at 200 nm. The RSDs for migration time were between 0.7% and 1.3% except for selenite of 5.1%. The RSDs for peak area were obtained between 2.9% and 7.4%. The calibration curves were linear from 10 to 200 mg/L with correlation coefficients greater than 0.9952. The LODs were 7.3, 10.9, 11.3, 12.9, 13.0, 13.9, and 17.4 mg/L for iodide, nitrate, bromide, selenite, bromate, tungstate and iodate. The KURT underground water sample spiked with seven anions at 50 mg/L were analyzed. The recoveries of spiked KURT sample ranged from 93.4% to 99.3%. The proposed method was successfully applied to determine seven anions in underground water sample.

Ultra-violet (UV) light is one of abiotic stress factors and causes oxidative stress in plants, but a suitable level of UV radiation can be used to enhance the phytochemical content of plants. The accumulation of antioxidant phenolic compounds in UV-exposed plants may vary depending on the conditions of plant (species, cultivar, age, etc.) and UV (wavelength, energy, irradiation period, etc.). To date, however, little research has been conducted on how leaf thickness affects the pattern of phytochemical accumulation. In this study, we conducted an experiment to find out how the antioxidant phenolic content of kale (Brassica oleracea var. acephala) leaves with different thicknesses react to UV-A light. Kale seedlings were grown in a controlled growth chamber for four weeks under the following conditions: 20°C temperature, 60% relative humidity, 12-hour photoperiod, light source (fluorescent lamp), and photosynthetic photon flux density of 121±10 μmol m-2 s-1. The kale plants were then transferred to two chambers with different CO2 concentrations (382±3.2 and 1,027±11.7 μmol mol-1), and grown for 10 days. After then, each group of kale plants were subjected to UV-A LED (275+285 nm at peak wavelength) light of 25.4 W m-2 for 5 days. As a result, when kale plants with thickened leaves from treatment with high CO2 were exposed to UV-A, they had lower UV sensitivity than thinner leaves. The Fv/Fm (maximum quantum yield on photosystem II) in the leaves of kale exposed to UV-A in a low-concentration CO2 environment decreased abruptly and significantly immediately after UV treatment, but not in kale leaves exposed to UV-A in a high-concentration CO2 environment. The accumulation pattern of total phenolic content, antioxidant capacity and individual phenolic compounds varied according to leaf thickness. In conclusion, this experiment suggests that the UV intensity should vary based on the leaf thickness (age etc.) during UV treatment for phytochemical enhancement.

본 연구는 패류 독소 중 기억상실성 독성을 유발하는 domoic acid의 분석법 개선, 검증 및 분석적용성을 살펴보 았다. SAX 카트리지 정제, 검체 및 추출용매 양의 변경 과 더불어 이동상을 용매구매 조건으로 변경시킨 분석법 은 지중해담치, 홍게 그리고 멸치의 세 가지 매트릭스를 대상으로 세 농도에 대하여 식품공전법과 비교하여 유효 성을 검증하였다. 그 결과 변경된 분석법은 LOD 0.02-0.03 mg/kg, LOQ 0.05-0.09 mg/kg, 일내 및 일간 정확도 86.2- 100.4%와 일내 및 일간 정밀도 0.2-4.0%로 CODEX가이 드라인을 만족하는 우수한 분석능을 나타내었다. 특히 변 경된 시험법에서는 domoic acid와 유사한 머무름 시간을 갖는 방해물질이 검출되지 않아 위양성 결과를 방지할 수 있을 것으로 생각된다. 더 나아가 본 분석법이 국내 유통 중인 수산물을 대상으로 적용될 수 있는지 확인하고자 식 품공전의 기억상실성 패독 분석법과 함께 수산물에 적용 하여 분석하였다. 그 결과 5종의 수산물 87건 중 공전시 험법으로 분석했을 때 domoic acid가 검출된 시료는 없었 으나 변경된 분석법을 통하여 멸치 1건에 대하여 0.14 mg/ kg의 domoic acid이 미량 검출되었다. 따라서 본 연구에 서 확립된 분석법은 수산물 중 domoic acid 분석에 활용 이 가능할 것으로 보인다.

This work reports the fabrication of a flexible Photodetector (PD) using Carbon Dots (CDs)/Polymer composite for Deep UV (DUV) photodetection. The CDs have been prepared using a simple and inexpensive heating process. The syncretic studies reveal the disordered graphitic core with surface functional groups and the excitation-dependent character of CDs. The synthesized CDs are stabilized via Poly Vinyl Alcohol (PVA) through a synergistic effect and investigated for different compositions (2–10 weight %) of CDs. The CDs/PVA composites shows improved absorbance at 208 and 335 nm compared to pure CDs owing to the bonding between them. This advantageous property of high absorption and photo response in the DUV region is utilized by employing CDs/PVA composite as a photo-sensing layer on the ITO-coated PET substrate in the PD. The performance of the PD was measured under dark, short (254 nm) and long (365 nm) UV region. Among all the compositions, 4% CDs/PVA PD exhibits superior performance in terms of high photo-to-dark current ratio (IPh/Id), responsivity and detectivity. The PD functioning and other parameters are discussed in detail and reported.

목적: 대학생을 대상으로 자외선을 포함한 청색광과 같은 유해광선에 대한 지식과 인식도를 알아보고자 하였다. 방법 : 2023년 4월부터 5월까지 온라인 설문 조사에 응답한 충남지역 대학생 103명을 대상으로 하였다. 설문 은 대상자의 일반적 특성에 관한 문항, 자외선과 청색광 차단렌즈의 착용실태에 대한 문항, 자외선과 청색광에 대 한 지식도 및 인식도 문항, 그리고 차단렌즈 선택을 위한 가이드라인의 요구도 문항으로 구성된 총 15문항의 설문 도구를 사용하였다. 통계분석은 SPSS 18.0을 사용하였다. 결과 : 자외선 차단을 위해 안경이나 콘택트렌즈를 착용하는 비율은 56.3%로 나타났으나 청색광 차단 안경이 나 콘택트렌즈를 사용하는 경우는 35.9%로 상대적으로 낮은 비율로 나타났다. 자외선과 청색광의 유해성에 관한 지식도는 각각 2.58±0.91, 2.44±0.98로 조사되었으며, 자외선과 청색광으로부터 눈 보호가 중요하다고 생각하 는 항목의 평균 점수는 각각 3.49±0.61, 3.35±0.68점으로 조사되어 자외선과 청색광 차단의 중요성에 대한 인 식도는 높은 것으로 나타났다. 결론 : 대학생들의 자외선과 청색광에 대한 지식도와 인식도는 높은 수준이었으나 청색광 차단렌즈에 올바른 선택법에 대한 지식은 낮은 수준을 나타냈다. 이에 청색광 차단렌즈의 올바른 선택을 위한 교육 강화와 가이드라 인의 구축이 필요할 것으로 판단된다.

Some plant pathogenic bacteria species are environmentally high-risk organisms that have a negative impact on agricultural production. Experiments with these pathogens in a biosafety laboratory require safety protocols to prevent contamination from these pathogens. In this work, we investigated the efficacy of using UV-C irradiation for the purpose of sterilizing an important plant pathogenic bacterium, Erwinia pyrifoliae, in a laboratory setting. For the test, the pathogen (1.71 × 108 CFU/ml) was inoculated on the surface of Potato Dextrose Agar (PDA) and the inoculated media were placed on a work surface in a biosafety cabinet (Class 2 Type A1) as well as on three different surfaces located within the laboratory: a laboratory bench, a laboratory bench shelf, and the floor. All the surfaces where the media were placed were in range of the UV-C beam projected by the UV lamp installed in the ceiling of the BSL 2 Class biosafety laboratory. Measurements of the reduction rate of bacteria under UV-C irradiation were conducted at different time intervals: after 10 minutes, 30 minutes, 1 hour, 2 hours, and 3 hours, respectively. The reduction rate of bacteria ranged from 90% to 99% after 10min irradiation, from 97.8% to 100% after 30 minutes of irradiation, from 99.1% to 100% after 1 hour of irradiation, and from 99.99% to 100% after 2 hours of irradiation. After 3 hours of irradiation, the pathogen was completely killed in all the test conditions. In the cases of the laboratory bench and the shelf of the laboratory bench, the effectiveness of UV-C irradiation differed slightly between the site where the bacteria located vertically under the lamp and the site where the bacteria were located 1 meter away horizontally from the site under of the lamp.

Plutonium exhibits a variety of oxidation states and has a strong affinity for complexation with organic ligands. Isosaccharinic acid (ISA) is a major degradation product of cellulose materials present in the low to intermediate radioactive wastes. The interaction between trivalent plutonium and ISA can significantly impact the migration and containment of plutonium in the repository environment. In this study, formation of Pu(III) and ISA complexes was investigated at an ionic strength of 1 M of NaClO4 using UV-Vis absorption spectrophotometry. To exclude the effect of the Pu(III) oxidation, absorption spectra were measured within 10 min after adding ISA into Pu(III) solution and processed using HYPSPEC software for deconvolution after baseline correction. Several previous studies showed that the presence of ligands accelerates the oxidation of Pu(III) to Pu(IV). To investigate whether ISA complexation can also accelerate the Pu(III) oxidation, UV-Vis absorption spectra changes over 24 hours were analyzed as a function of the ratio of ISA to plutonium concentration.

Radioactive products generated by long-term operation at NPP can become deposited on the surfaces of the system and equipment, leading to radiation exposure for workers during the decommissioning process. Chemical decontamination is one of the methods to reduce radiation exposure of workers, and there are HP CORD UV, CITROX, CAN-DECON. In the chemical decontamination process, organic acids are generally used, and representative organic acids include oxalic acid and citric acid. There are various methods for removing residual organic acid in decontamination liquid waste, such as using an oxidizing agent and an ion exchange methods. However, there is a problem in that oxidizing agent is used excessively or secondary wastes are generated in excess during organic waste treatment. However, when organic acid is decomposed using a UV lamp, the amount of secondary waste is reduced because it tis decomposed into CO2 and H2O. In this study, organic acid decomposition was evaluated as the contact time of the UV lamp. The experimental equipment consists of a UV reactor, a mixing tank, a circulation pump. The experimental conditions involved preparing 60 L of organic liquid waste containing oxalic acid, hydrogen peroxide and iron chloride. Test A was conducted using one UV reactor, and Test B was performed by connecting two UV reactors in series. As a result of the experiment, a decomposition rate of over 95% was shown after one hour for oxalic acid, and it was confirmed that the initial decomposition rate was faster as the contact time increases. Therefore, in order to increase the initial decomposition rate, it is necessary to increase the contact time of the UV lamp by connecting the UV reactors in series.