본 논문에서는 무도상 철도판형교에 열차하중이 재하되었을 때 변위를 최소화시키는 하부 수평브레이싱의 보강 형상 및 설치 위치를 검토하였다. 우선 거더와 수평 브레이싱으로 연결된 2거더 구조계의 전체 횡좌굴모멘트에 영향을 주는 요소를 검토하였다. 다음 으로는 무도상 철도판형교의 하부를 설치 위치를 달리하여 수평브레이싱으로 보강하였다. 보강된 무도상 철도판형교에 열차하중 및 거 더의 중심과 열차하중의 재하위치간의 편심거리(e)에 따라 발생하는 축방향의 비틀림모멘트를 고려하여 구조해석을 수행하였다. 보강모 델별로 지간 중앙에서의 단면의 중심에서 발생하는 변위를 검토하여 변위를 최소화시키는 모델을 선정하였다. 본 연구를 통하여 무도상 철도판형교에 열차하중 재하시 변위를 최소화시키는 하부 수평브레이싱의 보강 형상 및 설치 위치를 제안하였다.

Restraints of Branch Lines are used as earthquake-resistant support devices for fire-fighting pipes along with sway brace devices. The central types are aligned and fixed in a straight line with center of the pipe, but the eccentric types are fixed to on side of the pipe, so a bending moment occurs. In this study, three specimens each of central type and eccentric type were installed at an angle of 45° from the vertical and a monotonic compression load of 1340N was applied. All central type samples satisfied 17.8mm of the allowable displacement, but all eccentric type samples failed to meet the target load and buckled. Therefore, when considering the performance of eccentric type restraints, both compressive load and bending moment must be considered. Even through material mechanics calculations, the yield stress of eccentric type - 3/8 inch all threaded steel bolt - exceeds 320Mpa of the allowable stress. A experiment standards need to be established for eccentric type restraints.

Recently, the occurrence frequency of earthquake has increased in Korea, and the interests for seismic reinforcement of existing school buildings have been raised. To this end, the seismic performance evaluations for school buildings that did not accomplish the seismic design are required. In particular, this study checks the eigenvalue analysis, pushover curves, maximum base shears, performance points and story drift ratios, and then analyzes the seismic performance characteristics according to bracing configuration of steel frame system reinforcement. Also, this study presents the practical field application methods through the comparison of analysis results for the seismic performance characteristics.

강진은 적절한 내진 설계 기술이 적용되지 않으면 건물 붕괴로 인하여 극심한 피해가 발생할 수 있다. 이를 해결할 수 있는 면진 기술은 구조물과 지반 사이에 베어링 장치를 적용하여 지진 에너지를 흡수하고 건물에 전달되는 진동을 감쇠한 다. 본 연구는 고무 마찰 베어링 장치의 구조물 적용성을 검증하고 지진으로부터 안전성을 확보하기 위하여 고무 마찰 베어링 프레임 구조물에 대한 수치해석을 수행하였다. 수치해석 결과로써 최대 지붕 가속도와 총 밑면 전단력이 감소되어 내진 성능을 확인하였다. 또한, 최대 층간 변위 및 최대 잔류 층간 변위에 대한 분석 결과로 프레임 구조물을 경제적 복구 수준의 결과를 도 출하여 고무 마찰 베어링 장치의 우수한 내진 성능을 확인하였다.

Background/Objectives: 본 연구의 목적은 복부 브레이싱 운동과 복부 할로잉 운동을 결 합한 요부 안정화 운동프로그램이 20대 정상성인의 폐기능에 미치는 영향과 흡연자와 비흡 연자를 비교하여 그 차이를 알아보고자 하는 데 있다. Methods/Statistical analysis: 이를 위해 20대 정상성인을 대상으로 흡연집단(n=16)과 비 흡연집단(n=16) 두 그룹으로 모집하여 동일한 중재를 실시하였다. Findings: 흡연집단은 집단 내 기간 지남에 따라 폐기능 요인 중 FVC과 FEV1/FVC를 제 외한 FEV1과 PEF가 운동 전보다 유의하게 증가하였다(p<.05). 비흡연집단에서 기간 지남에 따라 폐기능 요인 중 FVC과 PEF를 제외한 FEV1, FEV1/FVC가 운동 전보다 유의하게 증가하 였다(p<.05). Improvements/Applications: 본 연구 결과, 복부 브레이싱 운동과 복부 할로잉 운동을 결 합한 요부 안정화 운동프로그램은 흡연집단과 비흡연집단 두 그룹의 폐기능 향상에 효과가 나타난 것을 알 수 있었다.

본 연구에서는 실대형 실험과 구조해석을 통해서 현장에서 사용되는 가새 시스템을 적용한 강관 골조 플라스틱 연동온실 의 횡하중 가력시험을 수행하고 성능을 분석하였다. 횡강성 과 응력을 분석하기 위해 실험체에 변위와 변형률계를 각각 9 개소 및 16개소 설치하였으며 가새의 설치 유무에 따른 성능 을 비교하기 위해 구조해석을 수행하였다. 실대형 실험과 가 새의 설치 유무에 따른 구조해석 결과 비교에서 구조물의 횡 강성이 많은 차이를 보였다. 실험체의 측고 부근에서 측정한 횡강성은 가새 시스템을 설치함으로 강성을 최대 44%까지 증 가시켰다. 현장에서 사용하는 가새의 접합부가 충분한 강성 을 확보하지 못함으로써 외력을 전체 구조물에 적절히 전달하 지 못하여 횡강성이 구조해석 결과보다 많이 저하되는 현상이 나타났다. 따라서 온실 설계 시 구조성능의 신뢰성을 높이기 위해서 가새 시스템의 연결방법, 설치위치, 부재의 최대길이 등 온실의 접합부에 대한 명확한 시공방법과 설계기준이 정립 되어 온실 설계가 이루어져야 할 것으로 판단된다.

Background: Trunk flexor-extensor muscles’ co-activation and upright posture are important for spinal stability. Abdominal bracing and maximal expiration are being used as exercises to excel torso co-contraction. However, no study has on comparison of the effect of this exercise on multifidus in the upright sitting posture. Objectives: This study aims to verify the effectiveness of abdominal bracing and expiration maneuvers in lumbo-pelvic upright sitting. Design: Cross-sectional study. Methods: Eighteen healthy women were recruited for this study. The multifidus muscle thickness of all subjects was measured in three sitting conditions (lumbo-pelvic upright sitting, lumbo-pelvic upright sitting with abdominal bracing, and lumbo-pelvic upright sitting with maximum expiration) using ultrasound. One-way repeated measure analysis of variance was used for the evaluation. Results: Compared to lumbo-pelvic upright sitting, lumbo-pelvic upright sitting with abdominal bracing and lumbo-pelvic upright sitting with maximum expiration were associated with significantly increment of muscle thickness. There was no significant difference in muscle thickness between lumbo-pelvic upright sitting with abdominal bracing and lumbo-pelvic upright sitting with maximum expiration. Conclusion: Abdominal bracing and maximum expiration could be beneficial to increasing lumbar multifidus thickness in lumbo-pelvic upright sitting.

2016 Gyeongju and 2017 Pohang earthquakes led Koreans to acknowledge that the Korean peninsula is not an earthquake-free zone anymore. Among various buildings crucial to after-shock recovery, general hospital buildings, especially existing old ones, are very significant so seismic retrofitting of those must be an important issue. Self-centering energy dissipative(SCED) brace is one of retrofitting methods, which consists of tendon with restoring force and friction device capable of dissipating seismic energy. The strength of the SCED brace is that the tendon forces a structure to go back to the original position, which means residual drift can be negligible. The residual drift is a very important parameter to determine usableness of general hospitals after shock. To the contrary, buckling-restrained braces(BRB) are also a very effective way to retrofit because they can resist both compressive and tensile, but residual drift may exist when the steel core yields. On this background, the seismic retrofitting effect of general hospitals reinforced with SCED braces was investigated and compared to that of the BRD in this study. As a result, although the floor acceleration cannot be reduced, the story drift and residual drift, and the shear demand of walls significantly decreased. Consequently, seismic retrofitting by SCED braces are very effective for domestic low-rise general hospitals.

Background: Improvement of lumbo-pelvic stability can reduce the compensatory action of the quadratus lumborum (QL) and selectively strengthen the gluteus medius (GM) during side-lying hip abduction (SHA). There are abdominal draw-in maneuver (ADIM) and abdominal bracing (AB) as active ways, and pelvic compression belt (PCB) as a passive way to increase of lumbo-pelvic stability. It is necessary to compare how these stabilization methods affect the selective strengthening of the GM. Objects: To investigate the effects of ADIM, AB, and PCB during SHA on the electromyography (EMG) activity of the GM, QL, external oblique (EO) and internal oblique (IO), and the GM/QL EMG activity ratio. Methods: A total of 20 healthy male adults participated in the study. The subjects performed three conditions in side-lying in random order: SHA with ADIM (SHA-ADIM), SHA with AB (SHA-AB), and SHA with PCB (SHA-PCB). To compare the differences among the three conditions, the EMG activities of the GM, QL, EO and IO, and GM/QL EMG activity ratio were analyzed using one-way repeated ANOVA. Results: The EMG activity of the QL was significantly higher in SHA-AB than in SHA-ADIM and SHA-PCB. The GM/QL activity ratio was significantly higher in SHA-PCB than in SHA-ADIM and SHA-AB. In addition, the figure for SHA-ADIM was significantly higher than that for SHA-AB. In the case of the EO, the figure for SHA-AB was significantly higher than corresponding values for the other two conditions. The figure for SHA-ADIM was significantly higher than that for SHA-PCB. The EMG activity of the IO was significantly higher in SHA-AH than in SHA-PCB. Conclusion: It can be suggested that wearing the PCB can more selectively strengthen the GM than to perform ADIM and AB during SHA. In addition, the ADIM can be recommended when there is a need to strengthen abdominal muscles during SHA.

Background: Abdominal bracing exercise (ABE) and abdominal hollowing exercise (AHE) improve the lumbar flexibility and pulmonary function in various patients, yet the efficacy of ABE or AHE have not yet been evaluated. Objects: The purpose of this study was to compare the lumbar flexibility and pulmonary function during both ABE and AHE in healthy adults. Methods: The study included 40 healthy adults, who were randomly divided into the experimental group and control group, each with 20 subjects. All subjects performed ABE (experimental group) and AHE (control group). The lumbar flexibility such as trunk flexion test (sitting and standing position) and schober test and pulmonary function such as the spirometer including forced vital capacity (FVC) and force expiratory volume in one second (FEV1) and chest circumference measurement (middle and lower chest) were measured, respectively. Two-way repeated analysis of variance was used to compare the lumbar flexibility and pulmonary function, respectively. Results: No significant effects of lumbar flexibility were observed on trunk flexion test from the sitting position (P=.478) and standing position (P=.096) in the ABE than in the AHE. However, the length of ABE was longer significantly than it of AHE (P=.024). No significant effects of lung function were observed on the FVC (P=.410) and FEV1 (P=.072) in the ABE group than in the AHE group. And also, no significant effects of chest circumference measurement were observed on the inspiration (P=.468) and expiration (P=.563) in middle chest circumference and inspiration (P=.104) and expiration (P=.346) in lower chest circumference. Conclusion: This study indicated that the ABE is only more effective in lumbar flexibility by lumbar length difference than AHE in healthy adults.

Background: The multiple hop test is an active performance test that has been commonly used to assess individuals with functional ankle instability. Previous studies have suggested that insufficiency of dynamic postural stability and passive stability during dynamic activities can have an influence on performance in the multiple hop test. However, no study has investigated the effects of dynamic postural stability training and ankle bracing on multiple hop test performance in individuals with functional ankle instability. Objects: The purpose of this study was to compare the immediate effects of dynamic postural stability training versus ankle bracing in the performance of the multiple hop test for participants with functional ankle instability. Methods: Twenty-nine participants with functional ankle instability who scored below 24 in the Cumberland Ankle Instability Tool were selected. The participants were randomly divided into two groups: a dynamic postural stability training group (n1=14) and an ankle bracing control group (n2=15). The multiple hop tests were performed before and after applying each intervention. Dynamic postural stability training was performed using visual-feedback-based balance-training equipment; participants in this group were asked to perform a heel raise in a standing position while watching the centering of their forefoot pressure to prevent excessive ankle inversion. Ankle bracing was applied in the control group. Results: When comparing the pre- and post-intervention period for both groups, both methods significantly improved the results of the multiple hop test (p<.05). However, no significant differences were shown between the dynamic postural stability training and ankle bracing groups (p>.05). Conclusion: Both dynamic postural stability training and ankle bracing showed significant improvement (2.85 seconds and 2.05 seconds, respectively) in test performance. Further study is needed to determine the long-term effects of dynamic postural stability training and to determine whether insufficient dynamic postural stability is a causative factor for functional ankle instability.

The friction damper can be used for improving the seismic resistance of existing buildings. The damper is often installed in bracing members. The energy dissipation capacity of the damping systems depends on the type of the structure, the configuration of the bracing members, and the property of dampers. In Korea, there are numerous low- to mid-rise reinforced concrete moment frames that were constructed considering only gravity loads. Those frames may be vulnerable for future earthquakes. To resolve the problem, this study developed a toggle bracing system with a high density friction damper. To investigate the improvement of reinforced concrete frames after retrofit using the developed damped system, experimental tests were conducted on frame specimens with and without the damped system. The results showed that the maximum strength, initial stiffness and energy dissipation capacity of the framed with the damped system were much larger than those of the frame without the damped system.

This study mainly treats a new type of the bracing friction damper system, which is able to minimize structural damage under earthquake loads. The slotted bolt holes are placed on the shear faying surfaces with an intention to dissipate considerable amount of friction energy. The superelastic shape memory alloy (SMA) wire strands are installed crossly between two plates for the purpose of enhancing recentering force that are able to reduce permanent deformation occurring at the friction damper system. The smart recentering friction damper system proposed in this study can be expected to reduce repair cost as compared to the conventional damper system because the proposed system mitigates the inter-story drift of the entire frame structure. The response mechanism of the proposed damper system is firstly investigated in this study, and then numerical analyses are performed on the component spring models calibrated to the experimental results. Based on the numerical analysis results, the seismic performance of the recentering friction damper system with respect to recentering capability and energy dissipation are investigated before suggesting optimal design methodology. Finally, nonlinear dynamic analyses are conducted by using the frame models designed with the proposed damper systems so as to verify superior performance to the existing damper systems.

Global trading regimes are currently undergoing significant changes. It is most vividly shown in the recent spread of FTAs and the surge of protectionism. These fast changes pose new challenges to many countries in terms of formulating and implementing their respective trade policies. The increasing confrontation between the United States and China in trade sectors now operates as a multiplier and accelerator of this fast-changing global trade landscape. Recent disputes between the two have underscored fundamental differences in understandings of the legal framework of the WTO Agreements and the nature of the obligations as Members, thereby further raising questions about the reinvigoration of multilateralism. The two countries’ retaliatory initiation of trade disputes against each other also involves third countries because of legal requirements and other considerations. The Sino-US trade disputes are thus not merely confrontation between the two largest trading partners; instead they carry wider systemic implications for both other countries and global trading regimes in transition.

The researches related to active control systems utilizing superelastic shape memory alloys (SMA) have been recently conducted to reduce critical damage due to lateral deformation after severe earthquakes. Although Superelastic SMAs undergo considerable inelastic deformation, they can return to original conditions without heat treatment only after stress removal. We can expect the mitigation of residual deformation owing to inherent recentering characteristics when these smart materials are installed at the part where large deformation is likely to occur. Therefore, the primary purpose of this research is to develop concentrically braced frames (CBFs) with superelastic SMA bracing systems and to evaluate the seismic performance of such frame structures. In order to investigate the inter-story drift response of CBF structures, 3- and 6-story buildings were design according to current design specifications, and then nonlinear time-history analyses were performed on numerical 2D frame models. Based on the numerical analysis results, it can be comparatively verified that the CBFs with superelastic SMA bracing systems have more structural advantages in terms of energy dissipation and recentering behavior than those with conventional steel bracing systems.

본 논문은 케이블 돔 구조물의 브레이싱 및 막재 보강 효과에 따른 비교분석을 하고자 한다. 텐세그러티 구조시스템은 초기응력의 도입을 통해 자기평형을 가지는 구조물로서 연속적으로 연결되어 있는 인장재와 이들을 연결해 주는 불연속의 압축재로 구성되어 있다. 본 연구에서는 경량화한 Hybrid 구조물인 케이블 돔의 불안정 현상이 면내 비틀림에 의해 발생함을 기본 Geiger형과 Zetlin형 모델에 브레이싱 및 막재를 보강하여 발생되는 효과를 알아본다. 또한, 쉘형 구조물의 구조불안정 거동이 초기조건에 매우 민감하게 반응하므로 초기형상불완전량 0.1%를 도입하여, 초기조건에 대한 영향도 알아본다.

본 연구에서는 1층 1경간 실제크기의 가력 프레임에서 내진보강에 적합한 비좌굴 knee brace을 설치하여 주기하중을 통해 가새의 지진저항능력을 실험하였다. 볼트 고정 채널이 이용된 비좌굴 knee brace는 지진력에 저항하는 코어와 두 개의 철골 플레이트로 만들어졌고 단면의 형태는 코어의 국부좌굴과 횡좌굴에 저항하도록 하였다. 비좌굴 kneebrace는 현장에서 조립이 용이하고, 시공방법 또한 간단하여 공간에 제약이 있는1층에 필로터를 가진 중저층 RC건물의 내진 보수/보강에 효과적으로 사용할 수 있다. 각 실험체에 대한 변수로 중심코어의 크기와 외부 보강재의 크기, 가이드 플레이트의 유무 등으로 정하였으며, 실험을 통해 얻어진 힘-변위 이력곡선을 통해 중심코어의 크기가 가장 큰 영향을 미치는 것으로 나타났다. 또한 가이드 플레이트의 유무에 따라 압축강도 수정계수와 파괴형태가 달라지는 것을 알 수 있었다. 각 실험체에 대한 결과는 AISC 2005 Seismic Provisions 규정에서 제시한 누적 연성도와 누적 소산에너지 측면에서도 충분한 효과를 발휘하는 것으로 나타났다.

The characteristics of structural behavior for a cable dome shows a strong nonlinearity and very sensitive by the initial imperfection. The instability phenomenon of Geiger-type cable dome structure is generated due to the in-plane twisting near the critical load level. In this study, therefore, the effect of bracing reinforcement resisting to the in-plane twisting is investigated for the Geiger-type model reinforced by bracing. The effect of initial imperfection is also studied because the structural instability phenomenon of shell-like structure is very sensitive according to the initial condition.

Lateral bracing has long been used in design practice to enhance the carrying capacity of the lateral buckling of the beam. Many factors. critically important to lateral bracing performance. do not appear in design formulas. Some of these factors are discussed in this study for the application to short 1 - beams under repeated loadings through parametric studies with an analytical model : the brace 10' cation along the length of the beam. the height of the bracing above the shear center of the beam. and the strength and stiffness of the brace. The parametric studies are carried out using a propped cantilever arrangement. and also using a geometrically (fully) nonlinear beam model for the brace as well as the beam to capture the system buckling. An idealized bracing system is configured to restrain lateral motion. but not rotation. A multiaxial cyclic plasticity model is also implemented to better represent cyclic metal plasticity in con. junction with a consistent return mapping algorithm.

브레이싱재를 사용하는 목적은 본 골조체계 즉 기둥과 보에 비해 단면(강성)이 작은 부재로 보강하여 횡력에 대한 강성효과를 크게 향상시키기 위함이다. 브레이싱재의 단면이 기둥과 보의 단면에 비해 월등히 작기 때문에 압축력에 의한 좌굴의 위험성과 휨량의 크기에 비례하여 부재 중앙에 발생되는 추가 모멘트(P-.DELTA. Effect)에 의한 불리한 영향 및 해석상의 어려움 때문에 브레이싱의 설계에 있어서 브레이싱재는 압축력을 받지 않는 것으로 간주하여 왔다. 그러나 최근 들어 구조물 해석에 정확도가 요구되어짐에 따라 브레이싱재의 정확한 거동에 대한 연구가 실험을 통해 활발히 진행되어 왔고, 특히 탄성한계를 지난 소성상태에서 반복하중에 의한 거동 규명이 큰 관심을 끌고 있다. 본 논문에서는 반복하중을 받는 강재 브레이싱재의 비선형 거동을 해석적 방법에 의해 규명했고, 그 결과를 실험결과와 비교하였다.