Liquid metal extraction (LME), a pyrometallurgical recycling method, is popular owing to its negligible environmental impact. LME mainly targets rare-earth permanent magnets having several rare-earth elements. Mg is used as a solvent metal for LME because of its selective and eminent reactivity with rare-earth elements in magnets. Several studies concerning the formation of Dy-Fe intermetallic compounds and their effects on LME using Mg exist. However, methods for reducing these compounds are unavailable. Fe reacts more strongly with B than with Dy; B addition can be a reducing method for Dy-Fe intermetallic compounds owing to the formation of Fe2B, which takes Fe from Dy-Fe intermetallic compounds. The FeB alloy is an adequate additive for the decomposition of Fe2B. To accomplish the former process, Mg must convey B to a permanent magnet during the decomposition of the FeB alloy. Here, the effect of Mg on the transfer of B from FeB to permanent magnet is observed through microstructural and phase analyses. Through microstructural and phase analysis, it is confirmed that FeB is converted to Fe2B upon B transfer, owing to Mg. Finally, the transfer effect of Mg is confirmed, and the possibility of reducing Dy-Fe intermetallic compounds during LME is suggested.

Background: Despite frequent shoulder injuries of rotator cuff muscle of golfers by the result of overuse and poor swing mechanics, there is little research on shoulder specific rehabilitation exercises for injured rotator cuff muscle and golf swing Objective: To examined the effect of rehabilitation exercise for golfers on the X factor and ground reaction force (GRF) according to phase of the golf swing. Design: Crossover study Methods: The participants were 13 amateur golfers selected for a 4 week rehabilitation exercise for golfers. A rehabilitation exercise for golfers consisting of 5 steps and 4 items (sleeper stretch, full side plank, push up to plank, high plank knee unders) were applied to all participants. A three dimensional motion analyzer and force platform (SMART-E, BTS, Italy) were used to measure the X factor (angle between shoulder and pelvis at top of back swing) and GRF according to phase of the golf swing. All dependent variables were measured before and after exercise. The collected data was analyzed using the paired t test and SPSS 21.0. Results: The GRF had a statistically significant increase in the impact phase and ratio impact/weight after rehabilitation exercise for golfers (p<.05). The Xfactor, GRF in top of back swing and finish were no significant differences between before and after exercise (p>.05). Conclusions: These results suggested that rehabilitation exercise for golfers was effective for increasing GRF in the impact phase and ratio impact/weight for amateur golfer.

MgB2 bulk superconductors are synthesized by the solid state reaction of (MgB4+xMg) precursors withexcessive Mg compositions (x=1.0, 1.4, 2.0 and 2.4). The MgB4 precursors are synthesized using (Mg+B) powders. Thesecondary phases (MgB4 and MgO) present in the synthesized MgB4 are removed by HNO3 leaching. It is found thatthe formation reaction of MgB2 is accelerated when Mg excessive compositions are used. The magnetization curves ofMg1+xB2 samples show that the transition from the normal state to the superconducting state of the Mg excessive sam-ples with x=0.5 and x=0.7 are sharper than that of MgB2. The highest Jc-B curve at 5 K and 20 K is achieved forx=0.5. Further addition of Mg decreases the Jc owing to the formation of more pores in the MgB2 matrix and smallervolume fraction of MgB2.

N-propyl-N,N-dimethylethanolamine의 용액을 만들기 위해 산성 조건 하에서 6분간 초음 파처리하여 제조하였다. N-propyl-N,N-dimethylethanolamine 의 촉매 가수분해는 온도 30~55 ℃에 서 uni-lamellar vesicle과 uni-lamellar와 multi-lamellar가 뭉쳐진 혼합물에서 연구되었다. 이들의 차 이는 촉매효과에 대해 multi-lamellar보다 uni-lamellar에서 영향이 크게 나타났다. Vesicle의 상전이 온 도는 37~44 ℃이며, multi-lamellar의 분자 입자의 크기는 uni-lamellar의 입자의 크기보다 크게 나타 났다.

N-propyl-N,N-dimethylethanolamine의 용액을 만들기 위해 산성 조건 하에서 6분간 초음 파처리하여 제조하였다. N-propyl-N,N-dimethylethanolamine 의 촉매 가수분해는 온도 30~55 ℃에 서 uni-lamellar vesicle과 uni-lamellar와 multi-lamellar가 뭉쳐진 혼합물에서 연구되었다. 이들의 차 이는 촉매효과에 대해 multi-lamellar보다 uni-lamellar에서 영향이 크게 나타났다. Vesicle의 상전이 온 도는 37~44 ℃이며, multi-lamellar의 분자 입자의 크기는 uni-lamellar의 입자의 크기보다 크게 나타 났다.

Yttrium aluminum garnet (YAG) powders were synthesized via mechanochemical solid reaction using with three types of aluminum compounds. reacted mechanochemically with all A1 compounds and formed YAM (yttrium aluminum monoclinic), YAG and YAP (yttrium aluminum perovskite) phases depending on the starting materials. The ground samples containing showed the best reactivity, whereas the ground sample containing A100H, which had the largest surface area, exhibited pure YAG after calcination at . The sample containing Al had the least reactivity, producing YAP along with YAG at . The types and grinding characteristics of the starting materials and grinding time are believed to be important factors in the mechanochemical synthesis of YAG.

In the present study, the focus is on the synthesis of nanosized WC powder by the chemical vapor condensation proces. The synthesized W-C system powder by the CVC process shows W2C, W, WO3 phases and can not shows WC phase. After recarburization heat treatment under mixture gas atmosphere of argon and hydrogen gases, the synthesized W-C system powder fully transformed to the pure WC. The synthesized WC powder after recarburization heat treatment has an average particle size of 20 nm. The nano-sized WC powder can be prepared by the combination of the CVC process and heat treatment methods.

Nano-sized WC powders were synthesized by vapor phase reaction using the precusor of tungsten ethoxide under helium and hydrogen atmosphere. The phases of the powder were varied with reaction Bone and gas flow rate. The powder size was about 30nm in diameter, and the tungsten carbide powder was coated by carbon layer. The synthesis of nano-sized WC powders was promoted as the hydrogen gas flow rate became higher. Inversely, tungsten oxide was formed by increasing the flow rate of helium gas. The synthesized powders were analyzed by XRD, FE-SEM, carbon analyzer etc.

(100) Si 기판위에 전자 빔 증착법을 이용하여 90Å두께의 Ti과 120Å두께의 Co를 순차적으로 증착시켰다. 그 후 질소분위기하의 350-900˚C온도구간에서 급속열처리함으로써 (100) Si 기판위의 Co/Ti 이중 박막의 실리사이드화 반응이 일어나게 했으며 이를 XRD, AES, TEM을 이용하여 분석하였다. 500˚C이하의 온도에서는 Co원자들이 Ti층쪽으로 빠르게 확산하여 Si와 반응하기 이전에 Ti원자들과 상호 혼합되어 어떠한 실리사이드도 형성되지 않았다. 500˚C에서 열처리된 시편의 고분해능전자현미경 영상을 통해 Co-Ti 혼합층과 실리콘 기판과의 계면에서 (100)Si 기판과 정합관계를 가지는 CoSi2가 형성되었음을 확인했다. 600˚C열처리에 의해 Co-Ti-Sitka성분 실리사이드가 형성되기 시작하였으며, 형성된 삼성분 실리사이드는 Ti의 out-diffusion에 의해 900˚C 이상의 온도에서는 불안정하였다. Co/Ti이중 박막에 의해 형성된 CoSi2는 실리콘 기판과 평탄한 계면을 가지며 실리콘 기판에 대해 (100)우선성장방위를 가졌다.

DSC와 XRD를 사용하여 Zr/Si 다층박막의 고상반응에 의한 비정질상과 결정상 생성 및 상전이를 확인하고 이를 유효구동력 개념과 유효생성열 개념 및 phase determining factor(PDF)모델을 이용하여 예측한 결과와 비교하였다. Zr/Si 다층박막은 비정질호 반응이 잘 일어났으며 이는 유효구동력 개념으로 예측한 바와 일치하였다. Zr/Si 계에서 생성되는 최초의 결정상은 ZrSi 였으며 유효생성열과 PDF모델로부터 예측된 최초의 결정상은 PDF 모델의 예측 결과와 일치하였다. Zr/Si 다층박막의 원자조성비가 1대 1일경우와 1대 2일 경우의상전이는 ZrSi→ZrSi2로 되었으며 이러한 상전이 과정은 유효생성열 다이아그램으로 해석되었다. ZrSi의 생성기구는 핵생성이 율속임을 규명하였고 ZrSi와 ZrSi2의 생성에 필요한 활성화에너지는 1.64±0.19eV와 2.28±0.36eV이었다.

Co/Si계에서 고상확산에 의하여 비정질상이 생성되는지의 여부를 유효구동력 개념을 이용하여 예측하였으며 유효생성열 개념 및 PDF모델로부터 결정상의 생성과 상전이를 예측하였다. 한편, DSC와 XRD를 이용하여 Co/Si다층박막에서의 비정질상의 생성여부와 결정상의 생성 및 상전이를 확인하여 모델로부터 예측한 결과와 비교하였다. Co/si계에서는 비정질상이 성장하지 않았으며 이는 유효구동력 개념으로부터 예측된 결과와 일치하였다. Co/Si계에서 생성되는 최초의 결정상은 CoSi였으며 유효생성열과 PDF모델로부터 예측된 최초의 결정상은 각각 CO2Si와 CoSi였다. 따라서 Co/Si계에서 생성되는 최초의 결정상은 구조적인 요소를 고려해 PDF모델의 예측결과와 잘 일치하였다. 증착당시 Co와 Si의 조성비가 2대 1일경우와 1대 2일 경우의 상전이는 각각 CoSi → Co2Si와 CoSi → Co2Si → CoSi → CoSi2의 초기단계의 생성기구는 각각 핵생성이 율속이었으며, 이들의 생성에 필요한 활성화에너지는 각각 1.71, 2.34, 2.79eV이었다.

a initial setting of mortar containing 0.2% xylitol and 2% sodium phosphate dibasic dodecahydrate was found to become fast. And a initial setting of mortar containing 0.3% xylitol was found to become slow. Also, mortar containing xylitol and PCM can reduce of maximum temperature and increase compressive and tensile strength compared to the plain mortar and mortar containing blast-furnace slag.