국내에서는 공용 중인 교량의 덧씌우기식 교면 포장 공사에서 빠른 개통을 위해 초속경 시멘트와 라텍스를 이용한 초속경 LMC 콘 크리트가 주로 적용된다. 고속도로에서는 교통 개방을 위한 콘크리트의 기준 강도를 압축강도 21MPa로 정하고 있다. 본 연구에서는 시공된 콘크리트의 강도 추정을 위한 적절한 비파괴 시험 방법을 선정하기 위해 약간의 손상을 포함하는 Break-off 시험을 적용하였 다. 실내 실험을 통해 수립된 시험 절차에 따라 47개 현장에서 시험을 수행하여 압축강도와 상관관계를 분석하였고, 현장적용성을 확 인하였다.

국내 시멘트 콘크리트계 교면포장의 개방강도는 압축강도를 기준으로 하고 있으나, 현장의 양생 조건과 동일한 콘크리트의 강도를 추정하여야 한다. 약간의 손상을 포함하는 비파괴 시험이 표면에서 측정하는 방법보다 압축강도와 상관관계가 높으므로, 본 연구에서 는 Break-off 시험과 압축강도의 관계를 도출하기 위한 일련의 연구를 수행하였다. 6개의 초속경 LMC 배합에 대해서 Break-off 시험을 수행하였고, 국내 교면포장 현장에 적합한 코어의 크기를 정하였다. 또한 유압펌프와 압력게이지, 가력부로 구성된 자체 시험기를 개 발하였다. Break-off 시험 결과 압축강도와 높은 상관관계를 나타내었고, 국내 시멘트 콘크리트 교면포장의 경계조건을 고려할 경우, 높이 70mm의 코어를 형성하는 것이 합리적이고, 신설포장이나 단면보수의 경우 높이 50mm인 코어를 사용할 수 있도록 제안하였다.

PURPOSES : The purpose of this study is to investigate the tendency of material property estimation under different concrete distress conditions and curling conditions when non-destructive tests such as rebound hammer and surface deflection test are applied to concrete pavement. METHODS : Nondestructive tests using Schmidt hammer and Falling Weight Deflectometer were performed to inspect the expressway concrete pavements constructed more than 20 years ago. Some results were compared with core tested elastic modulus and compressive strength. RESULTS : As a result of the rebound test, the section with Alkali-Silica Reaction(ASR) distress was outside the range of the existing estimation formula, but the control section was found to be within the range of the existing estimation formula. As a result of the physical property estimation through deflection test, the section with ASR distress showed greater fluctuations in the estimated material properties and deflection ratio compared to the control section, showing that the ASR damage seems to affect the slab deflection behavior. CONCLUSIONS : The rebound test may not sufficiently reflect the decline in material properties due to concrete damage. The deflection test can obtain results that reflect the deterioration of material properties, but it was confirmed that significant variability may occur, so it seems to necessary to perform complementary indoor core tests with nondestructive testing(NDT) tests.

Background: Various functional tests such as upper quarter Y-balance test (UQYBT) are used to evaluate shoulder stability and mobility in clinical or sports fields. Previous studies have been conducted to determine the correlation between the scapular or trunk muscle and UQYBT. However, the correlation between UQYBT and hip flexor, which can be considered as a core muscle, has not been confirmed. Objects: To verify the relationship between the UQYBT and scapular muscle (scapular protractor and lower trapezius [LT]), trunk muscle, and hip flexor strengths in healthy male participants. Methods: A total of 37 healthy male participants were recruited and underwent UQYBT in the push-up posture. The isometric strength of the scapular protractor, LT, trunk flexor and extensor, and hip flexors were measured using a smart KEMA strength sensor (KOREATECH Inc.). Results: The superolateral direction of the UQYBT was moderately to strongly related to trunk extensor (r = 0.443, p < 0.01), scapular protractor (r = 0.412, p < 0.05), LT (r = 0.436, p < 0.01), and both sides of the hip flexors (supporting-side: r = 0.669, p < 0.01; non-supporting- side: r = 0.641, p < 0.01). The inferolateral direction of the UQYBT was moderately related to the scapular protractor (r = 0.429, p < 0.01), LT (r = 0.511, p < 0.01), and both sides of hip flexors (supporting-side: r = 0.481, p < 0.01; non-supporting-side: r = 0.521, p < 0.01). The medial direction of the UQYBT was moderately to strongly related with the scapular protractor (r = 0.522, p < 0.01), LT (r = 0.541, p < 0.01), and both sides of hip flexors (supporting-side: r = 0.605, p < 0.01; non-supporting-side: r = 0.561, p < 0.01). Conclusion: This study showed that the strength of the scapular muscles, trunk muscles, and hip flexor muscles correlated to the UQYBT. Therefore, the strength of not only the scapular and trunk muscles but also the hip flexor muscles should be considered to improve the UQYBT.

Background: Falls are a common and serious problem in the elderly population. Muscle strength and balance are important factors in the prevention of falls. The Y-balance test (YBT) is used to assess dynamic postural control and shows excellent test-retest reliability. However, no studies have examined the relationship between lower-limb strength and YBT scores in elderly women. Objects: This study aimed to examine the relationship between lower-limb strength and YBT scores in elderly women. Methods: Thirty community-dwelling elderly women participated in the study. Lower-limb strength including hip flexor, hip extensor, hip abductor (HAB), hip adductor (HAD), knee flexor, knee extensor, ankle dorsiflexor, and ankle plantar flexor (PF) muscles was examined using a smart KEMA strength sensor (KOREATECH Inc.), and the YBT was used to assess dynamic balance. Relationship between lower-limb strength and YBT was demonstrated using a Pearson’s correlation coefficient. Results: HAB strength (r = 0.388, p < 0.05), HAD strength (r = 0.362, p < 0.05), and ankle PF strength (r = 0.391, p < 0.05) positively correlated with the YBT-anterior direction distance. Ankle PF strength was positively correlated with the YBT-posteromedial direction distance (r = 0.396, p < 0.05) and composite score (r = 0.376, p < 0.05). Conclusion: The results of this study suggest that HAB, HAD, and ankle PF strengths should be considered for dynamic postural control in elderly women.

선박 및 교량 구조물은 일종의 길이가 긴 박스형 구조로서 수직 굽힘 모멘트에 대한 저항력이 설계의 주요 인자이다. 특히 선박 거더는 반복적으로 불규칙적인 파랑하중에 장시간 노출되어 있기 때문에 구조부재의 연속 붕괴 거동을 정확하게 예측하는 것이 무엇보다 도 중요하다. 본 논문에서는 순수 휨모멘트를 받는 박스거더의 하중 변화에 따른 좌굴을 포함한 소성 붕괴 거동을 수치해석적 방법을 이용 하여 분석하였다. 분석대상은 Gordo 실험에서 사용한 세 가지 박스거더로 선정하였다. 구조강도 실험 결과와 비선형 유한요소해석에 의한 결과를 비교하여 차이가 발생하는 원인에 대해서 고찰하였다. 본 논문에서는 카본스틸 재료의 제작 시 필연적으로 사용하는 용접열에 의한 초기 처짐의 영향을 반영하기 위하여 전체와 국부적인 처짐 형상의 조합을 제안하였고, 이 결과는 실험 결과와 거동 및 최종강도 추정율이 7% 이내에서 잘 일치하고 있었다. 논문에서 검토한 절차 및 초기 처짐 구성에 대한 내용은 향후 유사 구조물의 최종강도를 분석하는데 좋 은 지침으로 사용할 수 있다.

최근 지구 온난화의 영향으로 태풍의 파괴력이 증가함에 따라 부유식 해상풍력발전기의 막대한 유실과 붕괴에 대한 우려가 깊어지고 있다. 부유식 해상풍력발전기의 안전한 운영을 위해 새로운 형태의 탈착형 계류 시스템 개발이 요구되고 있다. 본 연구에서 고 려한 새로운 반잠수식 계류 풀리는 기존의 탈착형 계류 장치에 비해 계류 라인으로 부유식 해상풍력 터빈을 보다 쉽게 탈부착할 수 있도 록 고안되었다. 8MW급 부유식 해상풍력발전기에 적용 가능한 반잠수식 계류 풀리의 초기 설계에 대한 구조적 안전성을 검토하기 위해 3D 프린터를 이용하여 축소구조모형을 제작하고, 이 모형에 대한 구조시험을 수행하였다. 축소 모형의 구조시험을 위해 3D 프린팅에 사 용된 ABS 소재의 인장 시편을 제작하고 인장시험을 수행하여 소재의 물성을 평가하였다. 인장시험에서 얻은 재료 특성과 축소모형 구조 시험과 동일한 하중 및 경계 조건을 적용하여 반잠수식 계류 풀리의 유한요소해석을 수행하였다. 유한요소해석을 통해 반잠수식 계류 풀 리의 구조적 취약 부분을 검토하였다. 반잠수식 계류 풀리의 주요 하중조건을 고려하여 구조모형시험을 수행하였으며, 재료의 최대인장 응력 이상이 발생하는 위치에 대해 유한요소해석과 시험 결과를 비교하였다. 유한요소해석과 모형시험의 결과로부터 작동조건에서는 Body와 Wheel의 연결부 구조가 취약한 것으로 파악되었고, 계류조건에서는 Body와 Chain stopper의 연결부 구조가 취약한 것으로 검토되었 다. 축소모형 구조시험에서 나타난 SMP의 구조 취약부는 구조해석의 결과와 일치하는 것으로 나타났다. 연구 결과를 통해 반잠수식 계류 풀리의 초기 설계에 대한 구조적 안전성을 실험적으로 검증할 수 있었다. 또한, 본 연구 결과는 상세설계 단계에서 반잠수식 계류 풀리의 구조 강도를 향상시키는데 유용하게 활용될 수 있을 것으로 판단된다.

In order to respond to environmental pollution, developed countries, including Korea, have begun to conduct research to utilize hydrogen energy. For mass transfer of hydrogen energy, storage as liquid hydrogen is advantageous, and in this case, the volume can be reduced to 1/800. As such, the transportation technology of liquefied hydrogen for ships is expected to be needed in the near future, but there is no commercialized method yet. This study is a study on the technology to test the performance of the components constituting the membrane type storage container in a cryogenic environment as a preparation for the above. It is a study to find a way to respond by analyzing in advance the problems that may occur during the shear test of adhesives. Through this study, the limitations of ISO4587 were analyzed, and in order to cope with this, the specimen was supplemented so that fracture occurred in the adhesive, not the adhesive gripper, by using stainless steel, a low-temperature steel, to reinforce the thickness. Based on this, shear evaluation was performed under conditions lowered to minus 243℃, and it was confirmed that the breaking strength was higher at cryogenic temperatures.

Conversion to modern hydrogen energy is required, and research on liquefied hydrogen cargo containment systems is needed for large-capacity transport and storage. In this study, changes in the mechanical properties of the adhesive required for storage and transport in liquid hydrogen were confirmed. The lap shear test was performed by realizing cryogenic conditions in a small chamber using liquid nitrogen and liquid helium. There was an increase of 11.0% in the -180℃ condition compared to room temperature, and an increase of 1.8% in the -230℃ condition compared to the -180℃ condition was confirmed. In the case of shear strain, it is known that it decreases as the temperature goes down. As a result of the experiment, it was confirmed that the value at room temperature and the value at -180℃ reduced the shear strain by 5.0%, and -230˚ compared to the -180℃ condition. An increase of 1.5% was confirmed in the C condition. In the case of the specimen tested at -230℃, the deformation in the gripper part was larger than in other tests, and it is judged that the maximum shear strength and shear strain were affected. In addition, in this study, there is a limitation in the experiment at -230°C rather than 253°C, which is the boiling point of hydrogen

Background: The CKCUES test evaluates the functional performance of the shoulder joint. The CKCUES test scores CKC exercises of the upper limbs to examine shoulder stability. Although the CKCUES test provides quantitative data on functional ability and performance, no study has determined the relationship between CKCUES scores and SA and TB muscle strength. Objects: The objective of this study is to determine the relationship between the CKCUES test scores and the strength of the SA and TB muscles in the CKCUES and unilateral CKCUES tests. Methods: Sixty-six healthy male volunteers participated in the study. A Smart KEMA strength sensor measured SA and TB muscle strength. Two parallel lines on the floor indicated the initial hand placement to start CKCUES tests. For 15 seconds, the subject raises one hand and reaches over to touch the supporting hand, then returns to the starting position. Results: The correlation between the CKCUES test scores and the strength of the SA was strong (r = 0.650, p < 0.001), and the TB was moderate (r = 0.438, p < 0.001). The correlation between the unilateral CKCUES test and the strength of the SA of the supporting side was strong (r = 0.605, p < 0.001), and swing side was strong (r = 0.681, p < 0.001). The correlation between the unilateral CKCUES test and the strength of the TB of the supporting side was moderate (r = 0.409, p < 0.001), and swing side was moderate (r = 0.482, p < 0.001). Conclusion: Our study showed that the CKCUES test had a strong association with isometric strength of SA and moderate association with that of TB. These findings suggest that the CKCUES test can evaluate the function of the SA. Moreover, the unilateral CKCUES test can evaluate unilateral shoulder function.

Background: The hip muscle plays various roles. Several types of functional performance tests are used for the assessment of patients with various lower extremity injuries. Hip muscle functions are important to test the performance of maintaining the spine, pelvic, and leg during bridging exercise. We designed a novel functional performance test tool, which we named close kinetic chain dynamic lower extremity stability (CKCLE) test to assess hip muscle functions. Objects: The purpose of this study was to determine the relationship between CKCLE test and hip extensor, external rotator, and abductor strengths. Methods: Twenty-two subjects were recruited in the present study (13 males and 9 females). The hip extensor, external rotator, and abductor muscle strengths were measured using a Smart KEMA strength sensor. When the examiner said “Go”, the subject performed the CKCLE test by moving one leg from the floor and touching the opposite knee and then return to the floor while maintaining the bridging position. The subjects attempted as many “touches” as possible in the allotted time (20 seconds) during the maximal tests. The correlation between the hip muscle (extensor, external rotator, and abductor) strength of the supporting leg and the number of CKCLE tests performed in 20 seconds was determined using the Pearson correlation. Results: Hip extensor (r = 0.626, p < 0.05), hip external rotator (r = 0.616, p < 0.05), and hip abductor muscle strengths (r = 0.475, p < 0.05) positively correlated with the number of CKCLE tests performed. Conclusion: We designed a CKCLE test and found that performance in the test correlated with hip extensor, external rotator, and abductor muscle strengths. The result suggests that the CKCLE test can be applied as a performance test to assess the functions of the hip extensor, external rotator, and hip abductor muscles.

Tensile strength was investigated for hybrid bar (HYB), in this study. HYB is made of both steel reinforcement and glass fiber. Cross section of HYB has a shape in which steel reinforcement wrapped with glass fiber. For the production of HYB, rebar of SD400 class and glass fiber of E class are used as main materials. Vinyl ester resin is used to harden a glass fiber. In order to evaluate for tensile strength of HYB, the direct tensile test was performed about total ten specimens. The length of total specimens is 2,200 mm including the grip. Diameter of HYB according to core diameter was considered as a test variable. Direct tensile test for HYB was performed using a UTM with a capacity of maximum 1,000 kN. Tensile strength and strain were measured for each specimen during the test. From the test results, tensile strength and elastic modulus were 317 ~ 341 MPa, 103 ~ 107 GPa, respectively. Especially, elastic modulus of HYB was improved in comparison with usual GFRP bars such as the Aslan 100 or the V-rod.

PURPOSES:The objectives of this study are to evaluate moisture sensitivity of various asphalt mixtures and to suggest an alternate method for the dynamic immersion test, which is used to determine the application of anti-stripping agent, by analyzing bond strength.METHODS:The bond strength of various asphalt mixtures such as hot mix asphalt, warm mix asphalt, and polymer-modified asphalt was evaluated by the ABS test. In order to characterize moisture sensitivity at different temperatures of the mixtures, the ABS test was conducted at -10°C, 5°C, 20°C, 40°C, and 54°C under both dry and wet conditions. The concept of the bond strength ratio was applied for objective moisture sensitivity analysis. Moreover, the bond strength characteristic was compared to the dynamic immersion test to suggest an alternate method to determine the application of anti-stripping agent.RESULTS AND CONCLUSIONS :Overall, the polymer-modified asphalt demonstrates the highest bond strength characteristic regardless of moisture condition and temperature. The bond strength characteristic displays a highly reliable linear relationship from 5°C to 40°C, and the relationship could be used to predict bond strength at any intermediate temperature. Based on the analysis of bond strength and retained asphalt ratio, the bond strength value of 1254 kPa could be applied as a criterion for anti-stripping agent.