It is reported that 48 pressurized heavy water reactors (PHWRs) are in operation, and 10 PHWRs including Wolsong-1 NPP have been permanently shut down in the world. In the case of PHWRs, which have been permanently ceased, they are managed through the delayed decommissioning method, but there are no cases of dismantling. Therefore, technology development is urgent for the effective decommissioning of PHWRs. Unlike PWRs, PHWRs are separated into coolant system and moderator system. Most of pipes and systems of coolant system are mainly composed of carbon steel, expect of the steam generator tubes which are composed of nickel alloy. On the other hand, the moderator system is composed of stainless steel. In the case of stainless steel, the inner layer of the oxide film is composed of chromium oxide, and the outer layer is composed of iron and nickel oxide in enriched. To remove two oxide layers, it is needs to different decontamination method, the coolant system can perform the system decontamination process through a reduction process, but in the case of the moderator system, the oxidation/reduction process is required because it has a material and oxide film similar to PWRs. In this study, this is evaluated the oxide film removal rate according to the type of stainless steel and temperature in order to remove the oxide film deposited in the moderator system. The experiments were carried out at temperatures of 60, 70, 80 and 90°C, with a concentration of 200 ppm of permanganic acid and nitric acid, and 2,000 ppm of oxalic acid, respectively. The results of the oxide film removal rate test for SUS304 showed 29% at 60°C, 38% at 70 and 80°C, and 41% at 90°C. For SUS403, the oxide film removal rate experiment results showed 62% at 60°C, 85% at 70°C, 94% at 80°C, over 99% at 90°C. The results showed that the removal efficiency of the oxide film increased as the temperature increased. Following the results of experimental, the optimum temperature of oxide removal in composed of the stainless steel material is to be 90°C for decontamination of PHWR.

Surface water temperature of a bay (from the south to the north) increases in spring and summer, but decreases in autumn and winter. Due to shallow water depth, freshwater outflow, and weak current, the water temperature in the central to northern part of the bay is greatly affected by the land coast and air temperature, with large fluctuations. Water temperature variations are large in the north-east coast of the bay, but small in the south-west coast. The difference between water temperature and air temperature is greater in winter and in the south-central part of the bay than that in the north to the eastern coast of the bay where sea dykes are located. As the bay goes from south to north, the range of water temperature fluctuation and the phase show increases. When fresh water is released from the sea dike, the surrounding water temperature decreases and then rises, or rises and then falls. The first mode of empirical orthogonal function (EOF) represents seasonal variation of water temperature. The second mode represents the variability of water temperature gradient in east-west and north-south directions of the bay. In the first mode, the maximum and the minimum are shown in autumn and summer, respectively, consistent with seasonal distribution of surface water temperature variance. In the second mode, phases of the coast of Seosan~Boryeong and the east coast of Anmyeon Island are opposite to each other, bordering the center of the deep bay. Periodic fluctuation of the first mode time coefficient dominates in the one-day and half-day cycle. Its daily fluctuation pattern is similar to air temperature variation. Sea conditions and topographical characteristics excluding air temperature are factors contributing to the variation of the second mode time coefficient.

The high-level nuclear waste (HLW) repository is a 500-1,000 m deep underground structure to dispose high-level nuclear waste. The waste has a very long half-time and is exposed to a number of stresses, including high temperatures, high humidity, high pressure These stresses cause the structure to deteriorate and create cracks. Therefore, structural health monitoring with monitoring sensors is required for safety. However, sensors could also fail due to the stresses, especially high temperature. Given that the sensors are installed in the bentonite buffer and the backfill tunnel, it is impossible to replace them if they fail. That’s why it is necessary to assess the sensors’ durability under the repository’s environmental conditions before installing them. Accelerated life test (ALT) can be used to assess durability or life of the sensors, and it is important to obtain the same failure mode for reliability tests including ALT. Before conducting the test, the proper stress level must be designed first to get reliable data in a short time. After that, acceleration of life reduction with increasing temperature and temperature-life model should be determined with some statistical methods. In this study, a methodology for designing stress levels and predicting the life of the sensor were described.

Since 1992, various numerical codes, such as TOUGH-FLAC and ROCMAS, have been developed and validated to dispose of Spent Nuclear Fuel (SNF) safely through a series of DEvelopment of COupled models and their VALidation against EXperiments (DECOVALEX) projects. These codes have been developed using different approaches, such as general two-phase flow and Richards’ flow which is an approximated approach neglecting gas pressure change, to implement the same multiphysics behaviors. However, the quantitative analysis for numerical results, which originated from different fundamental approaches, has not been conducted accurately. As a result, improper utilization of the approach to analyze certain conditions occurring such as dramatic gas pressure change may result in erroneous outcomes and systemic problem pertaining to TH analysis. In this study, the quantitative analysis of the two approaches, in terms of TH behavior, was conducted by comparing them with a 1D simulation of the CTF1 experiment carried out by laboratory experiment. The results calculated by different approaches show agreement in terms of TH behaviors and material properties change until 120°C. The results verify the applicability of Richards’ flow approach in a high temperature environment above the current thermal criteria, set as 100°C, and gas pressure change does not have a significant impact until 120°C. Therefore, although further studies for applicability of Richards’ flow are needed to suggest the appropriate temperature range, these quantitative analyses may contribute to the performance assessment of a compact repository using the high-temperature bentonite concept, which is currently gaining attention.

Bentonite has been considered as a potential buffer material in the engineering barriers of highlevel radioactive waste disposal systems. The intrusion of groundwater and heat from the waste change the temperature of the bentonite, which can alter the hydraulic properties of the bentonite. In this study, temperature effects on permeability were observed in two Ca-type bentonites. Laboratory tests were conducted on two types of block that were compacted using Korean Gyeongju bentonite and bentonil-WRK at different dry densities. Permeability tests were conducted at three different temperatures, namely 30°C, 60°C, and 90°C, using deionized water. Moreover, comparison between two Ca-type bentonites is carried out.

This study was carried out to determine the sprouting period of early and mid-season varieties, which includes ‘Atlantic’, ‘Chubaek’, and ‘Superior’, during the summer storage period in a semi-underground warehouse without cooling system. And also it was investigated the effect of chlorpropham [Propan-2-yl N-(3-chlorophenyl)carbamate, CIPC] treatment on the sprouting inhibition for the varieties. This study was conducted to figure out a sprout inhibitory effect when CIPC was applied to 1kg of the potato tubers at concentrations of 10 mg and 20 mg which are lower than the treatment concentrations of ca 30 mg prescribed by the positive list system (PLS). The internal temperature of the warehouse used in this experiment was lowered by 5°C or more than the outside temperature. The difference between the lowest and highest temperature during the experiment throughout the day was 5°C. It showed the effect of reducing to 1/2 of the difference in outdoor temperature. As for the sprouting of potatoes, the extremely early variety ‘Chubaek’ sprouts appeared at the 6th week of storage of control and it was the fastest sprouting potato among the control groups of the varieties. Sprouting began to appear in the Superior at the 6th week of storage, while the ‘Atlantic’ sprouted at the 8th week of storage. The appearance of sprouts was suppressed in all treatment groups of ‘Atlantic’ and ‘Superior’ varieties in CIPC treatments. Sprouts were observed in all treatment groups of ‘Chubaek’ after the 7th week, but the elongations of the sprouts in tubers were completely inhibited until the 8th week of storage. ‘Atlantic’ and ‘Superior’ seemed to have a sprouting inhibitory effect even with a low CIPC concentration of 10 mg·kg-1, with the exception of extremely early variety ‘Chubaek’ that breaks out of the dormancy quickly. Although weight loss occurred continuously during storage, it was minor loss of 0.7-1.6%. There was no consistent trend for changes of the loss in the varieties and CIPC treatments. Most common pathological disorder was the dry rot during the experiment, but only few were affected. The use of the tubers treated at 18°C and 90% RH for 10 days and the rack of refrigeration system which lead to lack of convection seemed to have suppressed the spread of pathogens.

With the development of drone technology, drones are being used in various industries. In general, drones use lithium-based battery pack, which is sensitive to external impact and temperature characteristics. Therefore, in order to prevent this problem, a battery case for protecting the battery from the outside is used. Usually, carbon fiber is used as case material, carbon fiber is expensive and has disadvantages of being difficult to manufacture. In this study, a battery case was fabricated to minimize the influence of external impact and temperature by using expanded polypropylene material, and also the battery efficiency test was performed using fabricated case. After basic design for battery case was conducted, a system capable of maintaining temperature was constructed by attaching a surface heating element inside the case, and the effect of maintaining temperature according to the presence or absence of the case was confirmed. Using manufactured prototype case, flight tests were carried out to check the battery voltage level according to the presence or absence of the case and to analyze the effect of improving the battery efficiency for the flight time of the drone.

This study was conducted in an indoor cultivation room and chamber where environmental control is possible to investigate the effect of temperature and irrigation interval on photosynthesis, growth and growth analysis of potted seedling cucumber. The light intensity (70 W·m-2) and humidity (65%) were set to be the same. The experimental treatments were six combinations of three different temperatures, 15/10℃, 25/20℃, and 35/25°C, and two irrigation intervals, 100 mL per day (S) and 200 mL every 2 days (L). The treatments were named 15S, 15L, 25S, 25L, 35S, and 35L. Seedlings at 0.5 cm in height were planted in pots (volume:1 L) filled with sandy loam and treated for 21 days. Photosynthesis, transpiration rate and stomatal conductance at 14 days after treatment were highest in 25S. These were higher in S treatments with a shorter irrigation interval than L treatments. Total amount of irrigation water was supplied evenly at 2 L, but the soil moisture content was highest at 15S and lowest at 25S > 15L > 25L, 35S and 35L in that order. Humidity showed a similar trend at 15/10℃ (61.1%) and 25/20℃ (67.2%), but it was as high at 35/25°C (80.5%). Cucumber growth (plant height, leaf length, leaf width, chlorophyll content, leaf area, fresh weight and dry weight) on day 21 was the highest in 25S. Growth parameters were higher in S with shorter irrigation intervals. Yellow symptom of leaf was occurred in 89.9% at 35S and 35L, where the temperature was high. Relative growth rate (RGR) and specific leaf weight (SLA) were high at 25/20℃ (25S, 25L), RGR tended to be high in the S treatment, and SLA in the L treatment. Water use efficiency (WUE) was high in the order of 25S, 25L > 15S > 15L, 35S, and 35L. As a result of the above, the growth and WUE were high at the temperature of 25/20℃.

This study aims to select eggplant cultivars adaptive to the hot temperature period greenhouse climate by water consumption, and growth performance of plants and fruits of different European eggplant cultivars, including ‘Bartok (BA)’, ‘Bowie (BO)’, ‘Black Pearl (BP)’, ‘Ishbilia (I)’, ‘Mabel (M)’, ‘Vestale (VE)’ and ‘Velia (VL)’, in substrate hydroponic cultivation under hot and humid greenhouse conditions. On the 118 DAT, the leaf number and stem dry weight were highest in ‘VL’, followed by ‘M’, and there was no significant difference in leaf dry weight among cultivars. The marketable fruit number per plant was 16.4 for ‘M’, which was higher than other cultivars, and ‘VE’ and ‘VL’ were 8.5 and 8.8, respectively. The weight per fruit was low for ‘M’ at 136 g, and the highest in ‘VE’ and ‘VL’ at 332 and 281 g, respectively. There was no significant difference in fruit production per plant. In this study, ‘M’, which has high water use efficiency and a large number of fruits, and ‘VL’, which required less quantity to water consumption for producing 200 g of fruit and had a high product weight, will have excellent adaptability in the UAE greenhouse condition.

This study was conducted to apply with an air duct for the cooling and a utilizing cultivating method that uses the fruiting node and the defoliation to the high-temperature vertical and hydroponic cultivation of the oriental melon. The lower fruiting node (LF) was to remove all third vines generated from 5 nodes of a secondary vine. The higher fruiting node (HF) was fruiting on the third vine generated from a first node of the third vine. The direction of the stem string; upward (UW), downward (DW). Four treatment conditions were applied with the LF-UW, LF-DW, HF-UW (control), and HF-DW. The leaf age of melon leaves was measured for photosynthesis at 3 days intervals, and the fruit characteristic was conducted on 79 fruits in each treatment. The photosynthesis rate steadily increased after leaf development, reaching 20.8 μmol CO2·m-2·s-1 on the 10 days, gradually increasing to 21.3 μmol CO2·m-2·s-1 on the 19 days, and reaching 23.4 μmol CO2·m-2·s-1 on the 32 days. After that, it lowered to 16.8 μmol CO2·m-2·s-1 on the 38 days and dropped significantly to 7.6 μmol CO2·m-2·s-1 on the 47 days. As a result of the fruit characteristics by fruiting nodes, the treatments of the fruit length was 12.6-13.4 cm, respectively, which was significant, and the fruit width was 7.9- 8.6 cm, respectively, was not significant. The soluble content ranged from 12.9 to 15.7°Brix, and the significance of all treatments, and higher than of LF-DW and HF-UW. The photosynthesis rate of melon leaves was good until 32 days after leaf development, but after that, the rate decreased. As for fruit quality, it was conformed that melons can be cultivated at the LF because the fruit enlargement and soluble content dose not decrease even when set at the LF. Results indicated that those can be used for LF and defoliation in the development of vertical and hydroponic cultivation method in high-temperature season.

수경 재배한 멜론의 생육과 수확 후 모의유통 시 품질 차이를 검토하였다. ‘루비볼춘추계’의 수경재배 된 멜론을 이용하여 저장 온도를 2℃와 5℃, 10℃, 20℃하여 모의유통 시 특성과 가용성고형물(SSC), 경도, 생체중 변화, 외관 등의 변화를 조사하였다. 멜론을 상온으로 유통하는 조건 하에서 저온저장에 따른 과실 특성을 본 연구에서 확인하였다. 멜론 저장 시 가용성고형물, 경도, 생체중, 외관이 저장온도에 따라 차이를 보였다. 가용성고형물은 멜론을 저온(2~5℃)에서 저장하여 모의유통 된 것이 상온(20℃)에서 다른 온도처리보다 높은 수준인 것으로 나타났다. 외관과 경도는 모의유통 중 저장 온도에 따른 영향이 지속적이지는 못하였지만 유통초기 저온(2~10℃) 저장이 외관 지수 및 경도 수치가 높은 경향이었다. 저장 온도에 따른 영향이 모의유통 시 계속 효과를 유지하지 못하여 국내 유통 시 이를 고려하여야 할 것이다. 본 연구 결과, 저장 온도에 따른 모의유통 중에 미치는 영향은 저장 직후 짧은 단기간에만 효과를 유지하여, 국내 유통 하에서 저장할 경우에는 바로 소비할 수 있도록 유도해야 할 것으로 생각된다.