청정 연료인 수소를 생산하기 위해 현재 가장 널리 사용되는 기술인 증기 개질이다. 이 방법으로 생산된 수소는 일산화탄소와 같은 불순물을 함유하고 있어, 이를 연료전지와 같은 응용분야에 사용하기 위해서는 적절한 정제 과정을 반드 시 거쳐야 한다. 최근 효과적인 정제 방법으로 분리막 기술이 각광받고 있다. 본 연구에서는 수소와 일산화탄소 혼합가스에서 수소 분리 및 회수를 위해 바이오가스 고질화용(biogas upgrading) 상용 폴리설폰(polysulfone) 고분자막의 활용 가능성에 대 해서 평가하였다. 먼저, 사용한 상용막의 물리화학적 특성에 대해서 평가하였고, H2/CO를 이용하여 stage-cut, 운전압력과 같 은 다양한 조건에서의 상용막 모듈의 성능 평가를 진행하였다. 마지막으로, 평가 결과를 바탕으로 공정설계를 위한 시뮬레이 션을 진행하였다. 본 연구에서의 상용 분리막 공정의 최대 H2 투과도와 H2/CO 분리계수는 각각 361 GPU와 20.6을 기록하였 다. 또한, CO 제거 효율은 최대 94%를 나타내었으며, 생산 수소 농도는 최대 99.1%를 달성하였다.

This study was conducted to apply with an air duct for the cooling and a utilizing cultivating method that uses the fruiting node and the defoliation to the high-temperature vertical and hydroponic cultivation of the oriental melon. The lower fruiting node (LF) was to remove all third vines generated from 5 nodes of a secondary vine. The higher fruiting node (HF) was fruiting on the third vine generated from a first node of the third vine. The direction of the stem string; upward (UW), downward (DW). Four treatment conditions were applied with the LF-UW, LF-DW, HF-UW (control), and HF-DW. The leaf age of melon leaves was measured for photosynthesis at 3 days intervals, and the fruit characteristic was conducted on 79 fruits in each treatment. The photosynthesis rate steadily increased after leaf development, reaching 20.8 μmol CO2·m-2·s-1 on the 10 days, gradually increasing to 21.3 μmol CO2·m-2·s-1 on the 19 days, and reaching 23.4 μmol CO2·m-2·s-1 on the 32 days. After that, it lowered to 16.8 μmol CO2·m-2·s-1 on the 38 days and dropped significantly to 7.6 μmol CO2·m-2·s-1 on the 47 days. As a result of the fruit characteristics by fruiting nodes, the treatments of the fruit length was 12.6-13.4 cm, respectively, which was significant, and the fruit width was 7.9- 8.6 cm, respectively, was not significant. The soluble content ranged from 12.9 to 15.7°Brix, and the significance of all treatments, and higher than of LF-DW and HF-UW. The photosynthesis rate of melon leaves was good until 32 days after leaf development, but after that, the rate decreased. As for fruit quality, it was conformed that melons can be cultivated at the LF because the fruit enlargement and soluble content dose not decrease even when set at the LF. Results indicated that those can be used for LF and defoliation in the development of vertical and hydroponic cultivation method in high-temperature season.

In this study, an accelerated weathering test was performed to examine the variation of thermal insulation performance according to the service life. A widely used class 1 thermal screen (matt georgette + polyethylene (PE) foam + chemical cotton + felt + matt georgette) was selected as the target thermal screen. The ultraviolet irradiation that reached the target thermal screen specimen (60 x 60cm) was 5mW/cm2. Thus, the ultraviolet irradiance was set to 5mW/cm2, and the exposure periods of accelerated weathering conditions on the specimens were set to 0, 282, 847, and 1412h. The radiation exposure periods of the weathering conditions for 0, 282, 847, and 1412h indicate the amount of ultraviolet accumulation for 0, 1, 3, and 5years, respectively. In the accelerated weathering test, the target specimens that completed each exposure phase were subjected to the hotbox test to analyze their thermal insulation performances. Consequently, the thermal insulation performance of the multi-layer thermal screen was estimated to degrade rapidly after approximately two years. In the accelerated weathering condition, a quadratic function model was used to calculate the expected service life, since it adequately described the variation in thermal insulation of the thermal screen according to time. The results showed that when the thermal insulation performance degraded by 5, 10, 20, and 30%, the expected service lives were 2.5, 3.3, 4.5, and 5.5years, respectively.

모바일 기반 온실에너지 계산프로그램을 제작하기 위해 먼저 주요 단일 피복재 10종 및 보온재 16종에 대한 열관류율 측정하였다. 또한 피복 및 보온재를 이중 및 삼중으로 다층 설치할 때 열관류율 추정을 위하여 이중 설치시 24조합, 삼중설치 시 59조합에 대한 열관류율을 핫박스를 이용하여 측정하였다. 단일 피복재에서는 PE필름(0.08mm) 대비 PO필름(0.15mm) 이 가장 열관류율이 가장 작고 열절감율이 가장 큰 것으로 나타났다. 단일 보온재에서는 열관류율에서는 외피가 있는 5겹 의 다겹보온커튼이 가장 보온력이 좋은 것으로 나타났다. 또한 단일자재에 대한 열관류율 값과 열저항값을 이용한 피복 및 보온재의 다층설치시의 총 열관류율 값을 산정하였고 실측 값과의 오차를 보정하는 선형회귀식을 도출하였다. 단일재료의 열관류율값에 의한 피복 및 보온재의 다층설치시 열관류율 추정 모형을 개발한 결과 모형평가지수가 0.90(0.5 이상일 때 양호)으로 나타나 추정치가 실측치를 매우 잘 재현 하고 있는 것으로 나타났다. 또한 시험온실을 통한 실증시험결과 예측된 열절감율이 실측치보다 상대오차 2%로 작게 나타나는 것으로 평가되었다. 이러한 연구결과를 기반으로 모바일 기반의 온실 에너지계산 프로그램을 개발하였다. 이 프로그램은 HTML5 표준 웹 기반 모바일 웹 애플리케이션으로 구현하였으며 N-Screen 지원을 통해 다양한 모바일 장치 및 PC 브라우 저에서 동작이 가능하게 제작되었다. 또한 온실 피복(12종) 및 보온재(16종)의 조합별 열관류율 및 난방부하계수를 제공 하여 농민이 모바일로 온실 위치, 형태 및 피복·보온재 등을 반영한 최대 주야간 냉난방부하 및 기간 난방부하를 산정할 수 있다. 대상 온실의 에너지 소비량에 대한 평가가 가능하며 온실의 지역 및 형태에 따라 피복 및 보온재의 최적 선택으로 에너지 절감형 온실 설계가 가능할 것으로 판단되었다.

In this study, the humidity control effect of a counter-flow ventilator was analyzed in a greenhouse with high relative humidity at night in the winter season. A case of the counter-flow ventilator was 0.96 × 0.65× 0.82(W× D × H, m) and there were heat transfer element and two fans for air supply and exhaust in the counter-flow ventilator. Two counter-flow ventilators were used in this study and the setting humidity of the ventilators was 80%. The temperature and relative humidity at night(18:00-8:00) in the greenhouse were measured. In a greenhouse without a counter-flow ventilator, the average temperature and humidity was 14.9°C, 82.8%, respectively. When the counter-flow ventilator was operated, the corresponding averages were 15.1°C, 79.9%. The independent sample t test of monthly temperature and relative humidity showed no difference in temperature, and a significant difference in relative humidity with 1% of the significance level. Therefore, using the counter-flow ventilator helps to control relative humidity in greenhouse and increase yield.. And further research considering the pros and cons of using the counter-flow ventilator is needed.

The results of internal temperature. productivity and immunity analysis of the laying hen house by the thermal environment and the supply of cold drinking water were as follows. The external temperature was changed from the minimum of 18℃ at night and the maximum of 36℃ during the day, and the internal temperature of the laying hens varied from 20~31℃. Thermal imaging analysis showed that the body temperature of the laying hen decreased by 2.4℃ with the supply of drinking water. The laying hen amount increased 2.36g and laying hen rate increased 3.62%p. Albumin increased 6.1%, decreased AST 15%, and decreased cholesterol 12.7%. Immune activators increased and T cells and B cells increased to increase immunity.

The purpose of this study is to analyze the distribution characteristics of mist spray particle size by devising a rotary mist spraying device to develop the evaporative salt water desalination system. The rotary mist spraying device was consisted of a BLDC sirocco fan, a spinning fan, a fan fixed shaft and a salt water supply device etc. In this study we analyzed the characteristics of spray particle size and distribution according to the variation of sirocco fan surface roughness(Ra, μm), revolutions(rpm) and salt water flow rate(mL/min). When sirocco fan surface roughness( Ra) was in the range of 0.27~7.65 μm, the spray particle size was 0.117~1.360 μm. And then more than 90% of spray particles were found to be less than 0.50 μm. When sirocco fan surface roughness(Ra) was in the range of 12.70~22.84 μm, the spray particle size was 2.51~184.79 μm and more than 98% of spray particles were found to be less than 13.59 μm. To analyze the effect of fan rotation speed on the size and distribution of spray particles, when surface roughness Ra was fixed 0.27 μm and fan rotation speed and salt water flow rate was respectively changed at 3,800~5,600 rpm and 2.77~8.28 mL/min, spray particle size was 0.341~0.541 μm. And when salt water flow rate was 9.74 mL/min and fan rotation speed was 3,800~5,200 rpm, spray particle size was in the range of 29.29~341.46 μm and in case of 5,600 rpm more than 98.23% of spray particles were in the range of 2.51~13.59 μm.

With the recent accelerated policy-making and interests in new renewable energy, plans to develop and supply the new renewable energy have been devised across multiple regions in Korea. Solar energy, in particular, is being applied to small-scale power supply in provincial areas, as solar cells are used to convert solar energy into electric energy to produce electric power. Nonetheless, in the case of solar power plants, the need for a large stretch of land and considerable sum of financial support implies that the planning step should take into consideration the most suitable meteorological and geographical factors. In this study, the proxy variables of meteorological and geographical factors associated with solar energy were considered in analyzing the vulnerable areas regarding the photovoltaic power generation facility across the nation. GIS was used in the spatial analysis to develop a map for assessing the optimal location for photovoltaic power generation facility. The final vulnerability map developed in this study did not reveal any areas that exhibit vulnerability level 5 (very high) or 1 (very low). Jeollanam-do showed the largest value of vulnerability level 4 (high), while a large value of vulnerability level 3 (moderate) was shown by several administrative districts including Gwangju metropolitan city, Jeollabuk-do, Chungcheongbuk-do, and Gangwon- do. A value of vulnerability level 2 (low) was shown by the metropolitan cities including Daegu, Ulsan, and Incheon. When the 30 currently operating solar power plants were compared and reviewed, most were found to be in an area of vulnerability level 2 or 3, indicating that the locations were relatively suitable for solar energy. However, the limited data quantity for solar power plants, which is the limitation of this study, prevents the accuracy of the findings to be clearly established. Nevertheless, the significance of this study lies in that an attempt has been made to assess the vulnerability map for photovoltaic power generation facility targeting various regions across the nation, through the use of the GIS-based spatial analysis technique that takes into account the diverse meteorological and geographical factors. Furthermore, by presenting the data obtained for all regions across the nation, the findings of this study are likely to prove useful as the basic data in fields related to the photovoltaic power generation.

Experiments of local cooling and heating on crown and root zone of forcing cultivation of strawberry ‘Seolhyang’ using heat pump and root pruning before planting were conducted. During the daytime, the crown surface temperature of the crown local cooling treatment was maintained at 18 ~ 22oC. This is suitable for flower differentiation, while those of control and root zone local cooling treatment were above 30oC. Budding rate of first flower clusters and initial yields were in the order of crown local cooling, root zone local cooling and control in root pruning plantlet and non pruning plantlet, except for purchase plantlet. Those of root pruning plantlet were higher than those of non pruning plantlet. These trends were evident in the yield of the first flower cluster until February 14, 2018, and the effect of local cooling and root pruning decreased from March 9, 2018. The budding rates of the second flower cluster according to the local cooling and root pruning treatments were not noticeable compared to first flower cluster but showed the same tendency as that of first flower cluster. In the heating experiment, root zone local heating(root zone 20oC+inside greenhouse 5oC) and crown local heating(crown 20oC+inside greenhouse 5oC) saved 59% and 65% of heating fuel, respectively, compared to control(inside greenhouse 9oC). Considering the electric power consumption according to the heat pump operation, the heating costs were reduced by 55% and 61%, respectively.

The drinking water supply system applicable to the laying hen consists of air-water heat pumps, drinking water tanks, heat stroage tank, circulation pumps, PE pipes, nipples, and control panels. When the heat pump system has power of 7.7 to 8.7 kW per hour, the performance coefficient is between 3.1 and 3.5. The supply temperature from the heat pump to the heat stroage tank was stabilized at about 12±1°C, but the return temperature showed a variation of from 8 to 14°C. Stratified temperature in the storage tank appeared at 12.°C, 13.5°C and 14.4°C, respectively. The drinking water supply temperature remained set at 15°C and 25°C, and the conventional tap water showed a variation for 23°C to 30°C. As chickens grow older, the amount of food intake and drinking water increased. y = -0.0563x2 + 4.7383x + 8.743, R2 = 0.98 and the feed intake showed y = -0.1013x2 + 8.5611x. In the future, further studies will need to figure out the cooling effect on heat stress of livestock.

In order to effectively utilize thermal energy, we analyzed the performance of the high efficiency latent heat storage system which can be used for greenhouse heating by using the developed phase change material. The system consists of hot water boiler, heat storage material, heat storage box, heat storage tank, circulation pump, control panel, and storage material. As a result, the latent heat and latent heat temperature of sodium acetate hydrate as latent heat storage material are 231.6 ~ 264.8kJ/kg, 54.95 ~ 55.48℃. As the number of cooling and heating increased, the latent heat temperature showed a slight change, but the latent heat decreased 33.1kJ/kg as the number of repetition increased. In the case of sodium acetate hydrate, large supercooling phenomenon was observed, and it was found that mixing of additives such as nucleating agent, thickener and supercooling agent can control the supercooling more effectively. The consumption of kerosene decreased until the temperature of the heat storage tank was raised to the set temperature by the closed circuit for 4 hours in the initial stage of the boiler operation. The heat exchange rate according to the change of the flow rate was maintained at the set temperature inside the heat storage tank after 4 hours of operation, Consumption was high. As the flow rate increased, the inlet and outlet temperature difference decreased, the heat exchange rate increased, and the heat exchange efficiency was in the range of 57.4 ~ 60.5%.

본 연구에서는 풍환경에 따른 열손실을 분석하는데 있어 필요한 풍속 기초자료를 제공하기 위하여 주요 11개 해안지역 중 온실밀집지역을 선정하여 기상환경 및 온실 방위를 조사 분석하였다. 대상지역은 난방온실 재배면적과 풍환경 기준으로 선정하였고 온실밀집지역은 50,000m2 이상인 지역을 대상으로 하였다. 11곳의 기상자료 중 기온,풍속, 풍향을 대상으로 30년간 자료를 수집하여 분석하였고 기온은 최저, 평균, 최고 기온을 나누고 풍속 및 풍향 기준은 기상청 분석 기준을 적용하였다. 온실의 배치방향은 형태가 대칭인 점을 감안하여 0~180o 범위로 자료를 수집하였다. 또한, 각 지역마다 풍향이 있으며 온실길이방향을 기준으로 하였을 때 적용되는 풍향은 달라질 수 있으며 이를 상대풍향으로 지칭하고 중복되는 점을 고려하여 0~90o 범위로 자료를 수집하였다. 11개 지역의 기온은 중부지방에 있는 보령, 영광 지역과 남부지방에 있는 9개 지역의 기온차이가 구분되었다. 중부해안 대상지역은 1월 최저기온은 약 3~4oC 정도 온 도가 높은 것을 확인할 수 있었고 평균기온은 약 3oC 정도 높았으며 월별 기온 중 최저기온을 선정할 때에 1 월 기온을 고려해야 되는 것으로 판단된다. 대상지역의 주풍향에 대한 월별 차이는 크게 발생하지 않았으며 풍향 분포에 따라 지역별로 서해안측, 서해 및 남해 경계 해안측, 남해안측으로 구분되어졌다. 풍속은 영광을 제외 한 10개 지역은 월간 풍속 포차이가 크게 발생하지 않는 것으로 판단된다. 대상지역의 온실의 방향은 길이방향 기준으로 분석하였으며 보령과 영광, 남해 지역은 60%이상 집중되어 있는 방향이 존재하였고 해남, 통영 지역은 약 90% 집중되어있는 방향이 존재하였으며 이는 경지정리로 인하여 방향이 편향되어있는 지역이 존재하는 것으로 판단된다.

쓰레기 소각장이나 산업체의 폐열을 농업에 활용한 사례는 몇몇 있었다. 그러나 온배수를 농업에 활용한 사례는 전무하였으며, 치어, 종패 등을 양식하는 수산업이 대부분이었다. 본 연구에서는 화력발전소의 온배수(폐열)를 열원으로 이용하는 120 RT 규모의 냉난방시스템을 제주특별자치도 서귀포시 안덕면 소재의 5,280m2 아열대 작물(망고) 재배 온실에 설치, 10월에서 다음해 2월까지 약 5개월 동안 난방을 실시하여 난방에너지 비용 절감 효과 등 분석하였다. 난방에너지 비용 절감효과는 면세경유에 대하여 87%이였으며, 또한 발전소의 온배수를 에너지원으로 재활용함으로 서 62%의 이산화탄소 배출 저감 효과를 얻었다. 본 연구를 계기로 2015년에 해수가 수열에너지 분야로 재생에너지에 포함되었다. 해수의 표층의 열을 히트펌프를 사용하여 변환시켜 얻은 에너지라는 수열에너지 분야의 기준과 범위를 볼 때, 이는 온배수가 재생에너지에 포함되었다고 말해도 과언이 아닐 것으로 사료된다. 그 이유는 온배수도 해수임에도 불구하고 온도가 일반 해수 보다 7~8oC 높아, 일반 해수를 히트펌프의 열원으로 이용하는 것보다 온배수를 열원으로 이용했을 때 히트펌프의 성능이 높기 때문이다. 또한 같은 해 농식품부의 폐열 재이용 시설 지원 사업이 발표되어, 발전소 온배수뿐만 아니라 산업체와 소각장의 폐열을 농업에 활용하면 지원을 받을 수 있게 되었다. 이 사업에 의하여 2015년 당진시, 하동군, 제주시, 곡성군이 선정되었으며, 2016년 태안군, 서귀포시 등이 선정되어, 2016년 말 곡성군과 제주시가 공사를 완료, 농업에 폐열을 활용하고 있으며(제주시는 발전소, 곡성군은 산업체 폐열을 이용하고 있음), 기타 지역은 추진 중이다.

본 연구에서는 농가현장에 보급되어 있는 350kW (175kW × 2대)급 수직형 지열히트펌프시스템으로 1,650m2 면적의 육묘온실에 2011년 6월 7일부터 9월 18일까지 냉방실험을 수행하여 냉방성능을 분석하고, 농가현장에서 지열히트펌프를 가동함에 있어 보다 효과적인 운용방법을 고려해보고자 하였다. 증발기측 물 온도차는 증발기 입구 물온도가 26.4℃에서 17.1℃로 변할 때 최대 1.7℃, 최소 0.9℃ 차이(평균 1.3℃)를 보였으며, 증발기 입구 물온도가 16.6℃에서 13.1℃로 변할 때 최대 1.1℃, 최소 0.8℃(0.9℃) 차이를 보였다. 히트펌프를 1대(175kW × 1대) 가동하는 경우, 증발기 입구에 유입되는 물온도 13.0~15.5℃(응축기 입구에 유입되는 물온도 19.4~21.2℃) 범위에서 냉방성능계수는 1.1~1.8, 발생한 냉방열량은 68.2~106.8kW, 소비전력은 61.0kW, 히트펌프를 2대(175kW × 2대) 가동하는 경우, 증발기 입구 물온도 10.0~13.0℃(응축기 입구에 유입되는 물온도 18.5~22.2℃) 범위에서 냉방성능계수는 2.0~2.7, 냉방열량은 203.9~262.0kW, 소비전력은 95~98kW 이었다. 6월의 누적 냉방열량은 14,718.6kWh(12,657,996kcal), 누적소비전력은 6,352.0kWh이었으며, 7월은 각각 26,765.1, 11,600.0kWh, 8월은 각각 28,437.2, 12,508.0kWh, 9월은 10,065.0, 5,125.0kWh로 8월이 가장 큰 냉방열량을 나타내었다.