전기 캐비닛은 병원 및 발전소와 같은 중요 시설물에서 운영과 관리를 위한 시스템 기기를 보관한 다. 지진과 같은 극한하중 하에서 중요 시설물은 지속적으로 운영 및 제어되어야 하기 때문에 전기 캐 비닛의 안전성은 평가되고 확보되어야 한다. 하지만 실험적 연구만으로 다양한 유형의 전기 캐비닛에 대한 내진성능 평가를 수행하는 것은 많은 제약이 있다. 따라서 다양한 연구자들은 전기 캐비닛의 유 한요소 모델을 구축하고 내진성능 평가를 수행하였다. 유한요소 모델은 beam-stick 요소를 기반으로 구축되거나 3차원 shell 요소를 기반으로 구축되어왔다. Beamk-stick 요소 기반 및 3차원 shell 요소 기반의 유한요소 모델에 대한 전체거동에 대한 비교를 수행한 사례는 있으나 국부거동에 대한 동적응 답을 비교한 연구사례는 없다. 전기 캐비닛은 내부에 시스템 기기가 보관되므로 내부의 국부거동 기반 의 내부응답을 포착할 수 있어야한다. 따라서 본 연구는 단문형 전기 캐비닛에 대한 beam-stick 요소 및 3차원 shell요소를 기반으로 유한요소 모델을 구축하고 동일한 높이에서 가속도 응답을 비교하였다. 결과적으로 beam-stick 요소 기반의 3차원 유한요소 모델은 전기 캐비닛 내부 응답 스펙트럼을 정확 히 예측할 수 없기 때문에 내부 응답 스펙트럼을 위해서는 3차원 shell요소 기반의 상세 유한요소 모 델을 사용해야 한다.
In this study, the elastic properties of aluminium nanocomposite representative volumetric element (RVE) reinforced with GNP have been analysed. Pure aluminium is lightweight and has low strength which is not suitable for various aerospace applications. Adding graphene to aluminium gives a highly strengthened nano-matrix. A 3D multiscale finite element (FE) representative volumetric element (RVE) has been developed to estimate the mechanical behaviour of GNP-reinforced aluminium graphene nanocomposite (AGNC). The factors influencing the behaviour of AGNC have been investigated with different weight fractions (wt%), sizes and orientations of GNP. The Young’s modulus of AGNC is enhanced by increasing the wt% of GNP and reducing the size of GNP in the aluminium matrix. The Young’s modulus of AGNC with 1% wt% has been enhanced two times and yield strength by five times than pure Al matrix. In the case of different sizes of GNP, the strength of 15-nm-diameter GNP AGNC enhanced two times and medium-sized GNP, i.e. 30 nm has shown a great combination of strength and ductility. After that different orientations have also influenced the mechanical properties and enhancement shown in layered orientation compared to different angles of GNP.
기어의 구조 안정성 및 치물림 성능을 분석하기 위하여 유한요소해석이 널리 사용된다. 본 연구에서는 스퍼 기어의 유한요소 모델 링 조건이 해석 결과 및 간소화 효과에 미치는 영향을 분석하였다. 기어 구조 해석의 간소화 방법으로 기어 몸체 및 잇수 간소화, 요소 망 생성 방식, 접촉 및 마찰 조건, 해석 조건 등을 선정하였다. 기어의 성능해석 지표로써 1주기의 기어 치물림 사이클 동안의 정전달 오차를 계산하였고, 간소화 지표로써 해석 소요 시간을 측정하였다. 유한요소해석을 통해 치물림 주기에 따른 접촉 응력 분포 및 변화 양상을 확인하였다. 모델링 조건에 따라 최대 전달 오차와 해석 소요 시간에 차이를 확인하고 원인을 분석하였다.
In this study, a finite element analysis was used to analyze the stress state and vibration characteristics generated by continuous contact between wheels and rails when driving urban railway vehicles. The rails applied to the analysis were divided into straight and curved shapes, and three-dimensional modeling was performed to analyze the changes in structural characteristics of wheels and rails when driving on straight and curved rails. As a result of the analysis, the stress characteristics were up to 6.5 MPa on a straight rail and 9.81 MPa on a curved rail, and it is believed that this increase in stress will increase noise due to an increase in friction at the interface. The vibration characteristics of the wheels and rails showed similar behavior from the 3rd mode to the 9th mode of the rail to the intrinsic vibration characteristics from the 4th mode to the 6th mode of the wheel.
본 논문에서는 유한요소해석을 통한 모듈러 구조물 접합부의 힌지접합부 연구에 관하여 소개한다. 모듈러 구조물은 모듈과 모듈을 적층하는 방식으로 공사를 진행하여 단위 모듈간의 기둥 및 보의 일체성을 기대하기 어려운 특성을 가지고 있다. 그러나 현 모듈러 설 계 시 이러한 구조적 특성을 무시하고 횡력에 대한 모멘트전달을 고려하여 기존 강구조와 동일한 방식으로 해석하고 있다. 더구나 모 멘트접합을 체결하기위해 모듈러 외부뿐만 아니라 내부에서 볼트 체결이 이루어져 조립 후 마감을 추가하는 불합리한 상황도 발생한 다. 이러한 일체성을 기대하기 어려운 특성을 고려하기 위하여 힌지접합을 활용한 모듈러구조시스템을 제안하였다. 논문에서는 기존 의 모멘트접합부에서 힌지접합부로 변경하였을 때 하중의 전달을 확인하기 위하여 이전 다른 연구에서 활용되었던 가위 모델을 변형 한 변형 가위 모델을 고안하여 접합부의 기본 이론을 제안·검토하였고, 기본을 바탕으로 계산된 결과는 구조해석 프로그램인 마이다 스 젠과 비교하여 검증하였다. 추가적으로 기존 모멘트접합부로 설계되었던 모듈러구조물을 힌지접합부로 변경하여 부재내력 및 사 용성을 검토하였다.
현재 우리나라에서 설계 및 시공되는 대부분의 철근콘크리트 벽식구조 공동주택은 상부벽체-하부골조 시스템으로 구성되어 있으며 서로 다른 상하부 구조시스템의 결합을 위해 전이보를 이용한다. 상부의 하중을 하부의 기둥 부재에 효율적으로 전달하기 위해 전 이보가 큰 강성을 지녀야하고 이로 인해 부재의 춤이 커져 많은 물량의 투입되고 전반적인 경제성이 떨어지게 된다. 이러한 문제점을 해결하기 위해 기둥을 벽체요소로 대체하고 일반적인 콘크리트 전이보에 비해 규모가 작은 경계보를 수평 구조요소로 활용한 새로운 경계보-벽체 시스템을 제안한다. 제안된 시스템의 축하중에 대한 성능 평가를 위해 3차원 비선형 유한요소해석을 수행하였다. 주요 설계변수로 상하부벽체 길이비, 경계보 부재의 전단보강근 간격, 하부벽체로 연속되는 상부벽체 수직근의 꺾임 비율, 슬래브 길이를 설정하고 제안된 시스템의 성능에 얼마나 기여하는지 분석하였다.
Metal bodies have generally been produced through machining process, even the smallest parts that are assembled and mounted on the metal body. In this study, we will study the process of manufacturing parts called SIM Tray through compound forging process instead of cutting. The process of replacing a series of SIM Tray production process with a composite forging process by simulating the forming process using DEFORM-3D and making process design, mold design, mold fabricating.
In this study, the flow analyses were carried out on the electric train models with three kinds of mounting materials installed at the front part of train. By examining the results of flow rate and pressure, It was investigated which type of design should be designed to be more efficient in high-speed operation. The three types of models are set as models a, b and c, and each has its own shape. For all models, the wind speed was set at 110 km/h, the most common driving speed for wide-area electric trains. In the case of the model a, it was good at cutting the wind flow as a round shape when viewed from the top. But from the side, it showed a vortex forming in the upper corner. To the contrary, the model b, which has a wedge-shaped side, could be seen from the top as a result of a vortex. Finally, in the case of model c combined with models a and b, the least vortex, front pressure, and resistance forces were shown by selecting the flow advantages of models a and b. By utilizing this study result, the flow velocity and pressure are investigated without flow experiment by shape of the front part of electric train, and the flow capacity can be seen.
본 논문에서는 유한요소해석을 이용하여 흉요추 후방 고정술의 고정분절 변화에 따른 척추 안정성을 평가하였다. 이를 위해 추간판, 인대, 추간관절(Facet joint) 등을 포함한 정상 흉요추(T10–L4)의 유한요소모델을 구축하였으며, 문헌으로 보고된 재료물성치를 부여하였다. 한편, L1을 병변 부위로 가정하였으며, L1-L2, T12-L2, T12-L1-L2 총 3가지 종류의 후방 고정술을 흉요추 유한요소모델에 구현하고 전방 굽힘, 후방 굽힘, 측면 굽힘, 축 회전의 하중 조건을 부여하였다. 시리즈 유한요소해석을 통해 고정분절에 따른 척추경 나사못, 척추골, 추간판의 변형량, 등가 응력, 운동 범위, 모멘트를 계산하였으며, 그 결과를 바탕으로 척추 안정성을 평가하였다.
직물섬유 보강 콘크리트(textile reinforced concrete, TRC)는 콘크리트 매트릭스를 직물섬유로 보강한 복합재료로 높은 강도 및 우수한 연성을 발휘한다. 본 논문에서는 TRC로 보강된 구조 부재의 성능 평가를 위해 그 유효물성치를 멀티스케일에 기반한 해석적 방법을 통해 평가하였다. 유효물성치 산정을 위해 감소차수모델(reduced order model)에 기반한 3차원 유닛셀 유 한요소해석법을 이용하였다. 계산된 유효물성치를 TRC 보강 휨 부재의 유한요소해석에 활용하여 하중-변위 그래프를 도출하였 다. 계산된 유효물성치를 TRC 보강 휨 부재의 유한요소해석에 활용하여 하중-변위 그래프를 도출하였으며, 이의 정확성을 평가 하기 위해 TRC 복합패널의 4점 휨실험을 수행하고 그 결과를 유한요소 해석결과와 비교 및 분석하였다.
V-type coupling, which is often applied to turbochargers, is a mechanical fastener where radial forces close turbine housing and bearing housing together. It prevents leakage of exhaust gases by contact pressure of the backplate caused by the load transmitted from the bolt-tightening torque. Therefore, it is important to study the mechanical behaviors of the coupling system in order to establish more accurate sealing assessment technologies. In this study, an experiment was first conducted to obtain the relationship between torque and its resulting axial force in a specially designed gage bolt. Strains were then measured when the torque was applied using the gauge bolts on the turbocharger. Thus, the magnitude of the axial force due to the bolt torque can be obtained inversely. In addition, the circumference and width strains of the turbocharger coupling were measured under the assembly load, and theses results were compared with the finite element results. As a result, they tend to be very similar, but in the ring area, analysis results show a relatively small value, and near the bolt, the analysis results are larger than the experimental strains. This is thought to be due to the reduced strains around the bolt by the hammering process.
This study was carried out to standardize the material properties of roll-over protective structure (ROPS) for agricultural tractor. The material properties which were obtained from stress-strain curve, a result of tensile test stress, were used to apply to the virtual test and varied from one production lot to the other and from one manufacturer to the other. And the finite element analysis was performed on the ROPS according to the OECD code. The results show that the load-displacement curves of virtual test were approximately equal to the actual test curves. The manufacturer or lot has been shown to have little effect on the properties of the material. Therefore, it is expected that the representative values that can be used in the finite element analysis can be determined by averaging the property values.
본 논문은 Shaped charge jet(SCJ)의 관통 과정을 유한요소해석을 통해 모사하여 제트 입사속도, 관통률 그리고 관통량 증분과 같은 물리량들을 획득하였다. 이 물리량들을 hydrodynamic 이론에 적용하여 입사 제트 속도의 효율을 분석한 결과, 입사 속도가 빠른 제트의 관통 효율은 이어지는 느린 제트에 비해 높은 것을 확인하였다. 이 효율은 hydrodynamic limit (HL) 미만인 제트인 경우 큰 폭으로 감소하였다. 한편, 시간에 따른 관통량 증분과 제트 소모량의 비교는 SCJ의 이론적인 관통현상 분석을 위해서는 길이 연장 효과를 고려해야함을 보였다.
Finite element analyses are carried out to understand the piezoelectric behaviors of ZnO nanowires. Three different types of ZnO nanowires, with aspect ratios of 1:2. 1:31, and 1:57, are analyzed for uniaxial compression, pure bending, and buckling. Under the uniaxial compression with a strain of 1.0 × 10−4 as the reference state, it is predicted that all three types of nanowires develop the same magnitude of the piezoelectric fields, which suggests that longer nanowires exhibit higher piezoelectric potential. However, this prediction is not in agreement with the experimental results previously reported in the literature. Such discrepancy is understood when the piezoelectric behaviors under bending and buckling are considered. When only the strain field due to bending is present in bending or buckling, the antisymmetric nature of the through-thickness stain distribution indicates that two piezoelectric fields, the same in magnitude and opposite in sign, develop along the thickness direction, which cancels each other out, resulting in a zero net piezoelectric field. Once additional strain contribution due to axial deformation is superposed on the bending, such field cancelling is compensated for due to the axial component of the piezoelectric field. Such numerical predictions seem to explain the reported experimental results while providing a guideline for the design of nanowire-based piezoelectric devices.
In this paper, we analyzed the safety on static and dynamic characteristics of a top-down evacuation instrument fixed on the exterior walls of a building using finite element analysis. For this purpose, the stress distribution characteristics of the H-beam structure were analyzed and the equivalent stress distribution, deflection displacement and natural frequency characteristics of the overall structure of the evacuation instrument were analyzed. The structures were applied with the materials of SS440 and SUS304. The static analysis results showed the elastic behavior with safety coefficients from 2.4 to 2.9, by confirming the structural safety. In addition, the analysis of the natural frequency characteristics confirmed that the vibration characteristics were higher than the external conditions of 20Hz.
Subsurface cavities in the asphalt pavement which can cause road depression and cave-in accidents influence on the safety of pedestrians and vehicle drivers in the urban area. The existence of subsurface cavity can increase the tensile strain at the bottom of asphalt layer which is an indicator of fatigue cracking potential, and leads to the weakening of the pavement structural capacity. In this study, the finite element (FE) analysis was conducted to examine the relationship between the critical pavement responses and influencing factors, such as cavity depth and size, asphalt layer thickness, and asphalt concrete modulus. The surface deflections and tensile strains calculated from the ABAQUS FE program were compared to those from ILLIPAVE. It is found from this comparison that there are a good relationship between two analysis results. A three dimensional finite element model which is essential to simulate the hexahedral cavity were used to generate the synthetic database of critical pavement responses. To validate the developed model, the deflection data obtained from field Falling Weight Deflectometer (FWD) testing in four different locations were compared to FE deflections. It is found that the center deflections obtained from the FWD testing and FE analysis are similar to each other with an error values of 2.7, 4.4, 5.5, and 11.9 % respectively. The FE model developed in this study seems to be acceptable in simulating actual field cavity condition. On the basis of the data in the database, various analyses were conducted to estimate the effect of influencing factors on the critical pavement responses. It was found that the tensile strain at the bottom of asphalt layer is affected by all the factors but the most affected by the cavity depth and asphalt concrete modulus. Further studies are recommended to properly account for the effect of cavity’s geometry to pavement response.
Pavement performance usually depends on the pavement’s material property, traffic and environmental conditions. Current pavement design programs such as the Mechanistic Empirical Pavement Design Guide use these factors in assessing the pavement life and performance in terms of different distresses like rutting and fatigue cracking. Theoretically, the cracking and rutting behaviour of pavements are based on accumulated strains experienced by the pavement which is brought by the weight and loading speed of vehicles. A steady state loading device was used in the field to evaluate pavement deflection’s behaviour in varying loading frequencies. It was observed that the pavement deflection increases as the loading frequency also increases until it approaches a certain frequency wherein the deflection decreases thereafter. In this study, a three-dimensional finite element pavement model was established using ABAQUS wherein the effect of the vehicle’s loading frequencies was analysed. The calculated static deflection and stress from the finite element (FE) model were found to have good correlation with the KENPAVE measured deflection and stress. The deflections of different pavement conditions were further studied and analysed by generating several pavement geometries and strength from the FE model using a frequency sweep response analysis. It was found that the geometric condition and the current modulus of the pavement can amplify the pavement deflection by a factor, β, depending on the loading frequency. The peak deflection was found to be occurring when the loading frequency approaches one of the pavement’s natural frequencies. Based on the finding from this study, the natural frequency is an important factor to be considered in designing pavements. Further study is recommended to understand more on how to minimize the effect of natural frequency to pavement life.