Since 1996, spent filters from the Kori unit 1 have been stored in enclosed areas such as the auxiliary building filter room. To dispose of these spent filters at a disposal facility, it is necessary to retrieve and package them according to the disposal criteria. The Kori unit 1 filter room is a 2.5- meter deep hole with 227 spent filters stored indiscriminately by type and radiation level. Furthermore, the exposure dose rate measurements revealed exceed 10 mSv/h, making it a challenging environment for workers. Therefore, in this study, we have developed a ‘Remote Processing System for Spent Filter Handling’ to minimize worker exposure and ensure safety throughout the entire process, from filter retrieval to radiation measurement, sample collection, compression, and packaging. We have completed performance testing through laboratory validation. The ‘Remote Processing System for Spent Filter Handling’ consists of four main components: a robot system for retrieving spent filters from the filter room, a transfer mechanism for moving spent filters to the lower area, a core ring device for sample collection, and finally, a compression/ packaging unit. The laboratory validation performance testing was conducted by installing these devices in a structure simulating the Gori-1 reactor filter room. The results confirmed that all processes, from spent filter retrieval to packaging, can be remotely operated without the need for filter drops or worker intervention. Through the laboratory validation, some areas for improvement were identified. These improvements should be taken into consideration when producing the system for future on-site applications.

Every engineering decision in radioactive waste management should be based on both technical and economic considerations. Especially, the management of low-level radioactive waste (LLW) is more critical on economic concerns, due to its long-term and continuous nature, which emphasizes the importance of economic analysis. In this study, economic factors for LLW management were discussed with appropriate engineering applications. Two major factors that should be taken into account when assessing economic expectations are the accuracy of the results and its proper balancing with ALARA philosophy (As Low As Reasonably Achievable). The accuracy of the results depends on the correct application of alternatives within a realistic framework of waste processing. This is because the LLW management process involves variables such as component type, physical dimensions, and the monetary value at the processing date. Two commonly used alternatives are the simplified lump sum present worth and levelized annual cost methods, which are based on annual and capital costs. However, these discussions on alternatives not only pertain to the time series value of operational costs but also to future technical advancements, which are crucial for engineers. As new research results on LLW treatment emerge, proper consideration and adoption should be given to technical cost management. As safety is the core value of the entire nuclear industry, the ALARA philosophy should also be considered in the cost management of LLW. The typical cost of exposure in man-rem has ranged from $1,000 to $20,000 over the past decades. However, with increasing concerns about health and international political threats, the cost of man-rem should be subject to stricter criteria, even the balancing of costs and safety concerns is much controverse issue. Throughout the study, the importance of incorporating proper engineering insights into the assessment of technical value for the financial management of LLW was discussed. However, it’s essential to remember that financial management should not be solely assessed based on the size of expenses but rather by evaluating the current financial status, the value of money at the time, and anticipated future costs, considering the specific context and timeframe.

Spent ion exchange resins have been generated during the operation of nuclear facilities. These resins include radioactive nuclides. It is needed to fabricate them into a stable form for final disposal. Cement solidification process is a useful method for the fabrication of them into a waste form for final disposal. In this study, proper conditions for the fabrication of them into a stable waste form were determined using the cement solidification process. In-drum waste forms were then produced at the conditions, where the stability of representative samples was evaluated for final disposal. The samples were satisfied to the Waste Acceptance Criteria for low and intermediate level radioactive waste disposal sites. This result can be utilized to derive optimal conditions for the fabrication of spent ion exchange resins into a final disposal form.

In general, radioactive waste with high radioactivity is made into a solid form with performance such as leaching restriction, shape retention, and structural stability so that radioactive waste does not affect humans and the environment as much as possible. This should be applied equally to radioactive waste, whether homogeneous or heterogeneous. The requirements are stipulated in the “Low and Intermediate Level Radioactive Waste Delivery Regulations” notice of the Korea Nuclear Safety and Security Commission. On the other hand, the waste acceptance criteria for domestic disposal facilities require immobilization of heterogeneous waste when the activity concentration is above a certain level, but do not provide specific immobilization performance requirements. In this study, the immobilization requirements applied to heterogeneous radioactive waste in various overseas countries operating low and intermediate-level radioactive waste disposal facilities were studied. First, the IAEA’s safety standards for radioactive waste immobilization, domestic regulations, and disposal facility waste acceptance criteria were reviewed. Countries operating surface disposal facilities such as the United States, France, Spain, and Japan and countries operating underground disposal facilities such as Sweden and Finland were divided to review the current status of immobilization application to heterogeneous waste in overseas countries. When reviewing overseas cases, each country’s disposal methods, types of disposal waste, and waste treatment criteria were also reviewed. It was found that the immobilization requirements for heterogeneous radioactive waste vary depending on the disposal method and the type of barrier used to ensure disposal safety in each country. The common point is to surround heterogeneous radioactive waste within a concrete lining of a certain thickness, and to apply the thickness, compressive strength, and diffusion coefficient of the concrete lining as immobilization performance requirements. Through this study, the immobilization performance requirements for heterogeneous radioactive waste in various overseas countries that stably operate low- and intermediate-level radioactive waste were confirmed, which is expected to contribute to specifying the performance requirements for immobilization of heterogeneous radioactive waste in domestic disposal facilities.

Republic of Korea is preparing to decommission Kori Unit 1 and Wolsong Unit 1. Decommissioning of a nuclear power plant proceeds in the following stages: shutdown, transition period, decontamination, cutting, waste treatment, and site restoration. When nuclear power plant is decommissioned, It is expected that approximately 80,000 drums of radioactive waste will be generated per nuclear power plant. Therefore, various technologies are being researched and developed to reduce this to approximately 14,500 drums. Technologies for waste volume reduction are largely mechanical and electrical/thermal methods. Representative examples of mechanical volume reduction technologies include super compactors and electrical/thermal volume reduction technologies include induction and plasma torch furnaces. Both technologies are effective reduction technologies, but the reduction ratio varies depending on the type or condition of waste before treatment. For example, as a result of testing waste reduction using a super compactor at NUKEM in Germany, the reduction ratio was found to be between 1.3 and 7 depending on the type or condition of waste such as chips, ash, scrap metal, sand, etc. And according to IAEA-TECDOC-1527, when reducing the volume of metals, aluminum, lead, copper, brass, etc. using induction melting, the waste volume reduction ratio is 5 to 20. In this paper, referring to these results, a melting test was conducted using a previously developed plasma torch with an output of more than 100 kW. And volume reduction characteristics of this plasma torch was considered depending on waste type or condition.

Radionuclides in low- and intermediate-level radioactive wastes from the decommissioning process of nuclear power plants were generally immobilized by cementation methods. Ethylenediaminetetraacetic acid (EDTA), which is extensively used as a decontamination agent, can affect the behaviors of radionuclides immobilized in cement waste forms. In this study, the effects of EDTA contained in simulated radioactive decommissioning wastes on the leaching characteristics of immobilized Co and Cs and the microstructure evolution of cement waste form. Co leaching was accelerated by the formation of Co–EDTA complexes with high mobility and solubility. Cs leaching was hindered by the ion competition with other metal–EDTA complexes for releasing from the cement waste form. Cs leaching was also retarded by carbonated layer at edge of the cement waste form, which process is facilitated by the presence of EDTA. Finally, the effects of EDTA on the leaching characteristics of immobilized Cs and Co and the microstructure evolution of the cement waste form should be considered to ensure the safety of disposal for lowand intermediate-level radioactive wastes.

Recently, the nuclear decommissioning and environmental restoration industries has significantly attracted as a new industry field due to the decision to decommission the KORI#1 and WOLSONG #1 nuclear power plant. In order to dispose of the decommissioning radioactive wastes generated during nuclear decommissioning, proper analysis is required, and disposal decisions are determined based on the analysis results. When dismantling a nuclear power plant, a few thousand of tons decommissioning waste are produced, so these require analysis for proper disposal. Therefore, a radionuclide facility for decommissioning waste analysis is essential for the disposal of the large quantities of decommissioning waste generated during nuclear power plant decommissioning. Korea Research Institute of Decommissioning (KRID) was established radionuclide analysis facilities to address above issues and support nuclear power plant decommissioning projects. The plan is to perform classification by type and radionuclide for all waste produced during nuclear power plant decommissioning and to support the disposal of radioactive wastes. In addition, we plan to establish validation methods for samples where verification methods are not established, in order to conduct efficient analysis and management. In this presentation, we will introduce the radionuclide facility currently under construction at KRID and present the space design, equipment layout, and utilization plans.

Concentrated effluent and spent ion exchange resins (IERs) from nuclear power plants (NPPs) were generated prior to the establishment of a disposal facility site and waste acceptance criteria have been temporarily stored at the NPPs because their suitability for disposal has not been confirmed. In particular, at the Kori Unit 1, which was the first to start the commercial operation in South Korea, the initially generated concentrated effluent and IERs are repackaged in large size of concrete containers and stored without provided regulation standard. The concentrated effluent is package as cementitious form in 200 L drums and repackaged in concrete containers, case of the IERs were solidified or dehydrated and repackaged in round concrete container. In this study, we review and propose a disposal plan for concentrated effluent and IERs repackaging drums that have not been confirmed to be suitable for disposal from the first operating nuclear power plant, Kori Unit 1, 2. First, the concentrated effluent was stored in four 200 L drums respectively, and then, it was again stored in concrete container and which was poured on top using grouted concrete. Therefore, the process was required by cutting concrete container for extracting the internal drums at first. Internal radioactive waste should be crushed to the suitable waste criteria and solidified, finally disposal in to the polymer concrete high integrity container (PC-HIC). IER was repackaged and disposal in square type of 200 L concrete drums respectively covered the cap. So, extracting the internal drums should be extracted after removing the cap of external concrete container. Cement solidification drums can be crushed and re-solidified or disposed in the PC-HIC. Stored IER after dehydrated can be disposal in PC-HIC. In conclusion, the container was used as a package that repackaging the concentrated effluent and IER was separated into two different types of waste depending on the level of contamination of radioactivity, the polluted area is disposed of as radioactivity contamination or the unspoiled area will be treated as self-disposal waste.

Dry active wastes (DAWs) are combustible waste generated during the operation and decommissioning of nuclear facilities, and are known to be generated in the amount of approximately 10,000 to 40,000 drums (based on 200 L) per unit. It consists of various types of protective clothing, paper, and plastic bags, and is stored in radioactive waste storage facilities. Therefore, reducing the volume of DAWs is an important issue in order to reduce storage costs and utilize the limited space of waste storage facilities. Heat treatment such as incineration can dramatically reduce the volume of waste, but as the waste is thermally decomposed, CO2, a global warming gas, is generated and there is a risk of emissions of harmful gases including radionuclides. Therefore, a heat treatment process that minimizes the generation of CO2 and harmful gases is necessary. One of the alternatives to incineration is to carbonize DAWs, dispose of carbonized materials below the release standard as non-radioactive waste, and selectively separate and stabilize inorganic components, including radionuclides, from carbonized DAWs. In this study, 13 types of DAWs generated from nuclear power plants were selected and their thermal decomposition characteristics were investigated to design a heat treatment process that replaces incineration. As a result of TGA analysis, the temperature at which thermal decomposition of each waste begins is 260-300°C for cotton, 320-330°C for paper, 315-420°C for synthetic fiber, 350°C for latex gloves. The mass of most samples decreased to less than 1 % of the initial weight after heat treatment, and dust suit and latex gloves had residues of 13.83% and 13.71% of the initial mass, respectively. The metal components of the residue produced after heat treatment of the sample were analyzed by EDS. According to the EDS results, cotton contains Ca and Al, paper contains Ca, Al and Si, synthetic fiber contains Ca, Cu and Ti, latex gloves contain Ca and Mg. Additionally, ICP analysis was performed to quantify the inorganic components. These results are expected to be applicable to the processing of DAW generated at nuclear facilities in the future.

Wasteform is the first barrier to prevent radionuclide release from repositories into the biosphere. Since leaching rates of nuclides in wasteform significantly impact on safety assessment of the repository, clarifying the leaching behavior is critical for accurate safety assessment. However, the current waste acceptance criteria (WAC) of the Gyeongju repository only evaluates leachability indexes for Cs, Sr, and Co, which are tracers for nuclear power plant waste streams. Furthermore, ANS 16.1, the current leaching test method used in WAC, applies deionized water (DI) as leachant. However, the interactions between wasteform and groundwater environment in the repository may not be reflected. Therefore, it is necessary to review the current leaching test method and nuclides that may require the extra evaluation of leachability beyond the Cs, Sr, and Co. Tc and I are key nuclides contributing to high radioactive dose in safety assessment due to their high mobility and low retardation factor. The groundwater conditions within the repository, such as pH and Eh significantly affect the chemical form of Tc and I. For example, Tc in H2O system tends to form hydroxide precipitates in neutral pH condition and TcO4 - in strong alkaline environments according to the Pourbaix diagram. In case of I, it generally exists in the form of I-, while it exists as IO3 - as Eh increases. Although the current leaching test at the Gyeongju repository applies DI as a leachant, the actual repository is expected to have a highly alkaline environment with a substantial amount of various ions in the groundwater. Consequently, the leaching behavior in the ANS 16.1 test and the actual disposal condition is different. Thus, it is necessary to analyze the leaching behavior of Tc and I with reflecting the actual disposal environment. In this study, the leaching behavior of Tc and I is investigated by following ANS 16.1 leaching test method. The solidified waste specimens containing 10 mmol of Re and I were manufactured with cement, which is widely used as a solidification material. Re was applied instead of Tc, which has similar chemical behavior to Tc, and NH4ReO4 and NaI were used as surrogates for Re and I. As a leachant, deionized water and cement-saturated groundwater were prepared and the concentration of nuclides in the leachant is analyzed by ICP-OES. As the result of this study, experimental data can be applied to improve the WAC and disposal concentration standards in the future.

At domestic nuclear power plant, concrete containers are stored to store waste generated before waste acceptance criteria (WAC) was established. Concrete container store concentrated waste liquid and waste resin. In order to disposal radioactive waste to a disposal site, it is necessary to conduct a characteristic evaluation inside the waste to check whether it satisfies the WAC. Two types of concrete containers are stored: round and square. The round type is filled with one 200-liter drum, and the square type is filled with four 200-liter drums. In the case of a round shape, the top lid is fastened with bolts, so it is possible to collect samples after opening the top lid without the need for additional equipment. However, in the case of a square shape, there is no top lid, and concrete is poured to cure the lid, so the separate equipment for characteristic evaluation is required. It is necessary to install a workstation for sample collection on the top of the concrete container, equipment for coring the top of the concrete container, and a device to prevent concrete dust scattering. Currently, the design of equipment for evaluating the characteristics of concrete containers has been completed, and equipment optimization through mock-up test will be performed in the future.

The decommissioning of Korea Research Reactor Units 1 and 2 (KRR 1&2), the first research reactors in South Korea, began in 1997 and the decommissioning status is currently proceeding with phase 3. It is expected that more than 5,000 tons of dismantled wastes will be generated as the contaminated building is demolished. Since these dismantled wastes must be disposed of in an efficient method considering economic feasibility, it is desirable to clearance extremely low-level wastes whose contamination is so minimal that the radiological risk is negligible. In Korea, in order to approve the clearance of radioactive waste, it must be proven that the nuclide concentration standards are met or that the dose to individuals and collectives is below the allowable dose value. At the KRR 1&2 decommissioning site, dismantled wastes have been steadily being disposed of through clearance procedure since 2021. Clearance was approved by the Korean Institute of Nuclear Safety (KINS) for one case of concrete waste in 2021 and two cases of metal waste in 2022. In 2023, the clearance of metal waste and asbestos waste has been approved so far, and in particular, this is the first case in Korea for asbestos waste. In this study, we compared the dose assessment methods and results of clearance wastes at the KRR 1&2 decommissioning site from 2021 to present. Dose assessment was conducted by applying the landfill scenario for concrete and asbestos and the recycling scenario for metal waste. The calculation codes used were RESRAD-onsite 7.2 and RESRAD-recycle 3.10. The dose conversion factors (DCF) for each age group (infant, 1y, 5y, 10y, 15y, adult) of the target nuclide used the values presented in ICRP-72, and in particular, geo-hydrological data of the actual landfill site was used as an input factor when evaluating landfill scenarios. As a result of the dose assessment, when landfilling concrete wastes in 2020, the personal dose and collective dose were evaluated the most at 2.80E+00 μSv/y and 4.83E-02 man·Sv/y, respectively.

Most of the radioactive wastes generated during the nuclear fuel processing activities conducted by KEPCO Nuclear Fuel Co., Ltd. are classified as the categories of intermediate and low-level radioactive waste. These radioactive waste materials are intended for permanent disposal at a designated disposal site, adhering strictly to the waste acceptance criteria. To facilitate the safe transportation of radioactive waste to the disposal site, it is necessary to ensure that the waste drums maintain a level of criticality that complies with the waste acceptance criteria. This necessitates the maintenance of subcritical conditions, under immersion or optimal neutron moderation conditions. This paper presents a criticality safety assessment of concrete radioactive waste under the most conservative conditions of immersion and moderation conditions for waste drums. Specifically, In order to send radioactive waste, which is the subject of criticality analysis, to a disposal facility, pre-processing operations must be performed to ensure compliance with waste accepatance criteria. To meet the physical characteristics required by the accepance criteria, particles below 0.2 mm should not be included. Thus, a 0.3 mm sieve is used to separate particles lager than 0.3 mm, and only those particles are placed in drums. The drums should be filled to achieve a filling ratio of at least 85%. A criticality analysis was conducted using the KENO-VI of SCALE. The Criticality Safety Analysis Results of varying the filling ratio of concrete drums from 85% to 100% presented in an effective multiplication factor of 0.22484. Additionally, the effective multiplication factor presented to be 0.25384 under the optimal moderation conditions. This demonstrates full compliance with the USL and criticality technology standards set as 0.95.

Plasma torch melting technology has been considered as a promising technology for treating or reducing the radioactive waste generated by nuclear power plants. In 2006, IAEA announced that the technology is able to treated regardless of the type of target wastes. Because of the advantage, many countries have been funding, researching and developing the treatment technology. In this study, oversea plasma torch melting facilities for radioactive wastes treatment are reviewed. Also, plasma torch melting facility developed by KHNP CRI is briefly introduced.

To safely dispose of highly radioactive spent resin and concentrate waste generated through nuclear power plant operations, it is essential to meet the physicochemical properties requirements of the packages and ensure the accuracy and reliability of radiological characteristics determination. Both spent resin and concentrate are packaged in high-integrity containers (HICs) after drying and are homogeneous waste products generated in the primary system and liquid radioactive waste treatment system. Meeting the physicochemical properties requirements does not appear to be difficult. However, to achieve reliable radiological characterization of high-integrity container packages, it is necessary to take a representative sample and perform accurate radiological analysis. Therefore, this paper discusses the methodology for evaluating the radionuclide inventory of high radioactive resin and concentrate packages, as well as the essential element technology and considerations. For relatively high radioactive resin and concentrate packages, the radionuclide inventory for each package should be evaluated with high reliability through direct radiological analysis of the representative samples collected for each package. This can contribute to the efficient operation of radioactive waste disposal facilities. Radionuclide-specific concentrations directly analyzed for each package will be managed in a database. As analytical data accumulates and direct measurements of high-integrity container package such as the radwaste drum assay system (RAS) become feasible, statistical techniques such as correlation analysis between easy-tomeasure (ETM) nuclides and difficult-to-measure (DTM) nuclides can lead to the development of efficient and reasonable indirect evaluation methods, such as scaling factor and the mean activity concentration method. As for the element technology, a remote representative sampling technique should be developed to safely and effectively take representative samples of highly radioactive materials, including granulated or hardened concentrate waste. Considerations should also be given to determining the sample quantity representing each package, as well as establishing radiation calibration and measurement methods appropriate to the radiation levels of the representative samples.

For the disposal of radioactive waste from nuclear facilities, assessing their radioactivity inventories is essential. As a result, countries with nuclear facilities are implementing assessment schemes tailored to their respective policies and available resources for radioactive waste management. This paper specifically describes the assessment scheme for radioactivity inventory applied to metal waste generated during the dismantling of the Japan Power Demonstration Reactor (JPDR), a 1.25 MW BWR. The distinctive aspect of the Japanese approach lies in the fact that, for a pair of a key nuclide and a difficult-to-measure (DTM) nuclide that lack a significant correlation in their concentrations, the mean activity concentration method was used. In this method, an arithmetic average of all measurements of the DTM nuclide from representative drums, including MDAs (Minimum Detectable Activities), was assigned to the concentration of the DTM nuclide for all drums, regardless of the concentration of its paired key nuclide. Conversely, for a specific pair of a key nuclide and a DTM nuclide with a significant correlation, the scaling factor method was applied, as is common in many other countries. This Japanese case can serve as a valuable reference for Korea, which does not have the option of using the mean activity concentration method in its assessment scheme.

Large amounts of concrete, metal, soil, and other radioactive waste are generated not only from nuclear power plants operating in Korea but also from nuclear power plant decommissioning. If it is confirmed through measurement of residual radioactivity that the concentration is below the allowable clearance level, they can be managed as general or industrial waste in accordance with the Nuclear Safety Act. The Korea Radioactive Waste Agency predicts that very low-level radioactive waste will be generated the most, at about 67.1%. If waste below clearance level among very low-level radioactive waste can be evaluated and reduced, a lot of costs can be saved. Among radioactive wastes, metal wastes in particular have various sizes, shapes, and densities. If radioactivity is measured without properly considering this, a large error occurs in the measured value even if the radioactivity value is the same. This requires a conservative measurement method using density correction taking into account the self-absorption effect. For conservative measurements, it is essential to compare measured values with calculated values using MCNP6 (Monte Carlo N-Particle). You must enter the geometry of the measurement environment and derive calculated values using F8 Tally. Clearance level of radioactive waste is determined through the above method. In addition, sufficient MDA (Minimum Detectable Activity) must be secured to determine clearance level by using NaI(Tl), plastic scintillator configuration, and lead shielding. Nuclide analysis is performed using a NaI(Tl) scintillator and the total gamma radioactivity is evaluated using a highly efficient plastic scintillator.

Radioactive liquid waste generated during the operation of domestic nuclear power plants is treated through a somewhat different liquid radwaste system (LRS) for each plant. Prior to the introduction of standard nuclear power plants, LRS used a concentrated water dry system (CWDS) to evaporate liquid waste and manage it in the form of dry powder. The boron-containing radioactive liquid waste dry powder was solidified using paraffin from 1995 to 2010, and about 3,650 drums (based on 200 L) of paraffin solidified drums are currently stored in nuclear power plants. Paraffin solidification drums do not meet the acceptance criteria for radioactive waste repositories because it is difficult to secure the homogeneity of the solidified body and there are concerns about leaching of radioactive waste due to the low melting point of paraffin. In order to solve this problem and safely permanently dispose of paraffin solidification drums, the characteristics of dry powder paraffin solidification drums containing boron-containing radioactive liquid waste must be analyzed and appropriate treatment technology utilizing the results must be introduced. This study analyzes the physical properties of paraffin, the chemical properties of boron-containing radioactive waste dry powder, and the physicochemical properties of paraffin solidification powder, and proposes an appropriate alternative technology for treating boron-containing radioactive waste dry drum. When disposing of the paraffin solidification drum with boron-containing radioactive liquid waste dry powder, the solidification body must be effectively withdrawn from the drum and the paraffin must be completely separated from the solidification body. When disposing the drum, the solidified material must be effectively extracted from the drum and the paraffin must be completely separated from the solidified material. Afterwards, the paraffin must be self-disposed, and the radioactive waste must be disposed of in accordance with acceptance criteria of repository. We looked at how each characteristic of the paraffin solidification drum with boron-containing radioactive liquid waste dry powder can be utilized in each of the above treatment processes.

Various types of solidifying materials are used to stabilize and solidify low and intermediatelevel radioactive dispersible waste. Portland cement is generally used to solidify various radioactive wastes because its facilities and processes are simple, less dangerous, and it has excellent compressive strength after curing compared to other materials. However, it is difficult to use Portland cement in radioactive waste containing highly water-soluble harmful substances such as sodium fluoride because it is prone to leaching harmful ingredients in immersion tests due to its low water resistance. In this study, solidification was achieved using an organic-inorganic hybrid solidifying binders consisting of inorganic binders such as Portland cement, blast furnace slag powder, silica fume, and organic binders such as epoxy resin. This material was then compared with a solidification material made of Portland cement alone. The mixing ratio of inorganic binders, water, and organic binders to simulated waste is 35%, 20%, and 25%, respectively. The mixing ratio of inorganic binders and water when using only Portland cement for simulated waste is 100% and 80%, respectively. The mixed paste was poured into a cylinder mold (Φ 5 × 10 cm) to seal the upper part, cured at room temperature for 28 days to produce a solidification specimen, and then subjected to various tests were performed, including compressive strength, immersion compressive strength, hydration peak temperature, length change, and immersion weight change. The compressive strength of the organic-inorganic hybrid solidification test was 13-17 MPa, the immersion compressive strength was 15-18 MPa, the hydration peak temperature was 33-36°C, the length change rate was -0.086%, and the immersion weight change rate was –2.359%. The compressive strength of the Inorganic solidification test using only Portland cement was 16-18 MPa, the immersion compressive strength was 20-21 MPa, the hydration peak temperature was 23-25°C, the length change rate was -0.150%, and the immersion weight change rate was -5.213%. The compressive strength and immersion compressive strength of the organic-inorganic hybrid solidification materials were slightly lower compared to those of Portland cement solidification materials, they still met the compressive strength standard of 7-12 MPa, taking into consideration the strength reduce and economic feasibility of the core drill process. Furthermore, it indicates that the rates of change in length and immersion weight decreased to about 1% and 5%, suggesting an improvement in water resistance. The above results suggest that applying the organic-inorganic hybrid solidification method to radioactive waste treatment can effectively improve water resistance and help secure long-term stability.

To effectively assess the inventory of radionuclides generated from nuclear power plants using a consistent evaluation method across diverse groups, it is imperative to analyze the similarity in radioactive distribution between these groups. Various methodologies exist for evaluating this similarity, and the application of statistical approaches allows us to establish similarity at a specific confidence level while accounting for the dataset size (degrees of freedom). Initially, if the variance characteristics of the two groups are similar, a t-test for equal variances can be employed. However, if the variance characteristics differ, methods for unequal variances should be applied. This study delineates the approach for assessing the similarity in radioactive distribution based on the analytical characteristics of the two groups. Furthermore, it delves into the results obtained through two case studies to offer insights into the assessment process.