For the sake of future generations, the management of radioactive waste is essential. The disposal of spent nuclear fuel (SNF) is considered an urgent challenge to ensure human safety by storing it until its radioactivity drops to a negligible level. Evaluating the safety of disposal facilities is crucial to guarantee their durability for more than 100,000 years, a period sufficient for SNF radioactivity to become ignored. Past studies have proposed various parameters for forecasting the safety of SNF disposal. Among these, radiochemistry and electrochemistry play pivotal roles in predicting the corrosion-related chemical reactions occurring within the SNF and the structural materials of disposal facilities. Our study considers an extreme scenario where the SNF canister becomes compromised, allowing underground water to infiltrate and contact the SNF. We aim to improve the corrosion mechanism and mass-balance equation compared with what Shoesmith et al. proved under the same circumstances. To enhance the comprehensibility of the chemical reactions occurring within the breached SNF canister, we have organized these reactions into eight categories: mass diffusion, alpha radiolysis, adsorption, hydrate formation, solidification, decomposition, ionization, and oxidation. After categorization, we define how each species interacts with others and calculate the rate of change in species’ concentrations resulting from these reactions. By summing up the concentration change rates of each species due to these reactions, we redefine the mass-balance equations for each species. These newly categorized equations, which have not been explained in detail previously, offer a detailed description of corrosion reactions. This comprehensive understanding allows us to evaluate the safety implications of a compromised SNF canister and the associated disposal facilities by numerically solving the mass-balance equations.

Deep borehole drilling is essential not only to select the host rock type for deep geological disposal of high-level radioactive waste (HLW), but also to identify the characteristics of the disposal site during the site selection process. In particular, since the disposal depth of HLW is considered to be over 300 m, deep borehole drilling must be performed. In deep borehole drilling, drilling design, excavation, and operation may vary depending on the rock type, drilling depth, and drilling purpose etc. This study introduced cases in which Korea was divided into four geotectonic structures and four representative rock types and conducted with a goal of 750 m drilling depth. Prior to this, a review of deep drilling cases conducted at domestic and abroad was presented. If sufficient time and cost are available, several drilling holes can be excavated for various purposes, but if not, one or two drilling holes should be used to achieve the objectives of various fields related to HLW disposal. The presence of bedding, strata or fault zones depending on the type of rock, etc. may affect drilling deviation or circulating water management. In addition, unlike drilling in general geotechnical investigation drilling, the use of polymers or grouting agents is limited to determine hydraulic and geochemical characteristics. This report introduces the experience considered during the design and drilling process of deep drilling in granite, gneiss, sedimentary rock, volcanic rock, etc., and is expected to be used as basic data when carrying out future HLW projects.

Spent nuclear fuels (SNFs) are stored in nuclear power plants for a certain period of time and then transported to an interim storage facility. After that, SNFs are finally repackaged in a disposal canister at an encapsulation plant for final disposal. Finland and Sweden have already completed the design of the spent nuclear fuel encapsulation plant. In particular, Finland has begun the construction of the encapsulation plant and is on the verge of completion. Korea Radioactive Waste Agency (KORAD) is conducting a conceptual design of a deep geological repository for SNFs. Conceptual design of the encapsulation plant is part of the research activity. It is highly required to draft an operation process of the encapsulation plant before an actual design activity. As part of the activity, Finnish design concept of the encapsulation plant and experience were thoroughly reviewed. Finally a preliminary concept of the operation process was proposed considering Korean unique situations such as the volume of SNFs estimated to be disposed of, types of transportation cask and other considerations.

Uranium (U) is a hazardous material that can lead to both chemical and radiological toxicity, including kidney damage and health issues associated with radiation exposure. In South Korea. In Korea, where shallow weathered granitic aquifers are widespread, several previous studies have reported high levels of radioactivity in shallow groundwater. This ultimately led to the closure of 60 out of 4,140 groundwater production wells in South Korea. In this study, we examined aquifers currently dedicated to drinking water supply and investigated a dataset of 11,225 records encompassing 103 environmental parameters, based on the random forest classifier. This dataset comprises 80 physical parameters associated with the hydraulic system and 23 chemical parameters linked to water-rock interactions. Among the hydraulic parameters, the presence of a coarse loamy texture in the subsoil displayed a notable positive relationship with the concentration of uranium, implying that it plays a significant role in forming redox conditions for the leaching of uranium from host rocks. Fluorine (F), a major product of water-rock interaction in granitic aquifers, exhibited a positive correlation with the distribution of uranium concentrations. The positive relationship between F concentration and uranium levels suggests that the dissolved uranium originates from groundwater interacting with granites. In conclusion, our findings indicate that two key factors, namely the infiltration capacity of soil layers and the aqueous speciation in groundwater resulting from interactions with local solids, play important roles in determining uranium concentrations in granitic aquifers.

The HADES (High-level rAdiowaste Disposal Evaluation Simulator) was developed by the Nuclear Fuel Cycle & Nonproliferation (NFC) laboratory at Seoul National University (SNU), based on the MOOSE Framework developed by the Idaho National Laboratory (INL). As an application of the MOOSE Framework, the HADES incorporates not only basic MOOSE functions, such as multi-physics analysis using Finite Element Method (FEM) and various solvers, but also additional functions for estimating the performance assessment of Deep Geological Repositories (DGR). However, since the MOOSE Framework does not have complex mesh generation and data analyzing capabilities, the HADES has been developed to incorporate these missing functions. In this study, although the Gmsh, finite element mesh generation software, and Paraview, finite element analysis software, were used, other applications can be utilized as well. The objectives of HADES are as follows: (i) assessment of the performance of a Spent Nuclear Fuel (SNF) disposal system concerning Thermal-Hydraulic-Mechanical-Chemical (THMC) aspects; (ii) Evaluation of the integrity of the Engineered Barrier System (EBS) of both general and high-efficiency design perspective; (iii) Collaboration with other researchers to evaluate the disposal system using an open-source approach. To achieve these objectives, performance assessments of the various disposal systems and BMTs (BenchMark Test), conducted as part of the DECOVALEX projects, were studied regarding TH behavior. Additionally, integrity assessments of various DGR systems based on thermal criteria were carried out. According to the results, HADES showed very reasonable results, such as evolutions and distributions of temperature and degree of saturation, when compared to validated code such as TOUGH-FLAC, ROCMAS, and OGS (OpenGeoSys). The calculated data are within the range of estimated results from existed code. Furthermore, the first version of the code, which can estimate the TH behavior, has been prepared to share the contents using Git software, a free and open-source distribution system.

The concept of deep geological disposal for high-level radioactive waste is based on an engineered barrier system (EBS), including a canister, bentonite buffer and backfill material. The bentonite buffer is key component of the EBS to prevent groundwater infiltration and radionuclide leakage. However, the bentonite buffer can become saturated due to groundwater flow through the excavation damaged zone in the adjacent rock, causing erosion of bentonite buffer and affecting the long-term performance of EBS. While the RH (relative humidity) sensor is commonly used to assess the degree of saturation in the bentonite buffer, it has a critical challenge due to its sensor size, which can disturb the overall integrity of the bentonite buffer during the initial installation process. In contrasts, the electrical resistivity test, widely known as a non-destructive method, is used to predict soil properties such as the degree of saturation and water contents. This method measures the electric resistance of materials using electric current induced by electric potential difference between two electrodes. Notably, there is no study that assess the integrity of bentonite buffer in a nuclear waste repository using electrical resistivity measurement. This study presents the electrical resistance numerical module under steady state using commercial finite element method (FEM), and quantitatively estimate the change of electrical resistance according to saturation and erosion of bentonite buffer. Furthermore, the electric potential and current density distribution formed between two electrodes are analyzed.

Long-term climate and surface environment changes can influence the geological subsurface environment evolution. In this context, a fluid flow pathway developing and connection possibility can be increased between the near-surface zone and deep depth underground. Thus, it is necessary to identify and prepare for the overall fluid flow at the entire geological system to minimize uncertainty on the spent nuclear fuel (SNF) disposal safety. The fluid flow outside the subsurface environment is initially penetrated through the surface and then the unsaturated area. Thus, the previously proved reports, POSIVA in Finland, suggested that sequential research about the fluid infiltration experiment (INEX) and the investigation is necessary. Characterizing the unsaturated zone can help predict changes and ensure the safety of SNFs according to geological long-term evolution. For example, the INEX test was conducted at the upper part of ONKALO, about 50 to 100 m depth, to understand the geochemical evolution of the groundwater through the unsaturated zone, to evaluate the main flow of groundwater that can approach the SNF disposal reservoir, and to estimate the decreasing progress of the buffering capacity along the pathway through the deep geological disposal. In the present study, a preliminary test was performed in the UNsaturated-zone In-situ Test (UNIT) facility near the KAERI underground research tunnel to design and establish a methodology for infiltration experiments consistent with the regional characteristics. The results represented the methodological application is possible for characterizing unsaturated-zone to perform infiltration experiments. The scale of the experiment will be expanded sequentially, and continuous research will be conducted for the next application.

Raman characteristics of various minerals constituting natural rocks collected from uranium deposits in Okcheon metamorphic zone in Korea are presented. Micro-Raman spectra were measured using a confocal Raman microscope (Renishaw in Via Basis). The focal length of the spectrometer was 250 mm, and a 1800 lines/mm grating was installed. The outlet of the spectrometer was equipped with a CCD (1,024256 pixel) operating at -70°C. Three objective lenses were installed, and each magnification was 10, 50, and 100 times. The diameter of the laser beam passing through the objective lens and incident on the sample surface was approximately 2 m. The laser beam power at 532 nm was 1.6 mW on the sample surface. Raman signal scattered backward from the sample surface was transmitted to the spectrometer through the same objective lens. To accurately determine the Raman peak position of the sample, a Raman peak at 520.5 cm-1 measured on a silicon wafer was used as a reference position. Since quartz, calcite, and muscovite minerals are widely distributed throughout the rock, it is easy to observe with an optical microscope, so there is no difficulty in measuring the Raman spectrum. However, it is difficult to identify the uraninite scattered in micrometer sizes only with a Raman microscope. In this case, the location of uraninite was first confirmed using SEM-EDS, and then the sample was transferred to the Raman microscope to measure the Raman spectrum. In particular, a qualitative analysis of the oxidation and lattice conditions of natural uraninite was attempted by comparing the Raman properties of a micrometer-sized natural uraninite and a laboratory-synthesized UO2 pellet. Significantly different T2g/2LO Raman intensity ratio was observed in the two samples, which indicates that there are defects in the lattice structure of natural uraninite. In addition, no uranyl mineral phases were observed due to the deterioration of natural uraninite. This result suggests that the uranium deposit is maintained in a reduced state. Rutile is also scattered in micrometer-sizes, similar to uraninite. The Raman spectrum of rutile is similar in shape to that of uraninite, making them confused. The Raman spectral differences between these two minerals were compared in detail.

According to the analysis of the Korean Radioactive Waste Society, saturation of nuclear power plant temporary storage is expected sequentially from 2031, and accordingly, the need for highlevel radioactive waste disposal facilities has emerged. In order to establish a repository for high-level radioactive waste, the performance and safety analysis of the repository must be conducted in compliance with regulatory requirements. For safety analysis, it needs a collection of arguments and evidence. and IAEA defined it as ‘Safety case’. The Systematic method, which derives scenarios by systematizing and combining possible phenomena around the repository, is widely used for developing Safety case. Systematic methods make use of the concept of Features, Events and Processes (FEP). FEP identifies features that affect repository performance, events that can affect a short period of time, and processes that can have an impact over a long period of time. Many countries, such as Finland, Sweden, Japan, United States, etc., are in process of licensing disposal facilities by using ‘Safety case’. And they then develop their own project-specified FEP lists and employ them for performing safety assessments. However, the systematic procedure for generating scenarios for safety evaluation is not clearly defined. According to the International Atomic Energy Agency (IAEA) Safety Standards Series (SSG- 23), the bottom-up method is an approach for conducting safety analysis using Features, Events, and Processes (FEPs). However, the process of how each FEP is utilized to establish a scenario for safety evaluation remains unclear. Additionally, there exists not only a bottom-up approach for generating scenarios using FEPs, but also a hybrid scenario development method that incorporates a top-down approach based on safety functions. Each country address scenario derivation in accordance with the adopted hybrid method. Nevertheless, a challenge arises in its application due to discrepancies between their approach and the hybrid approach specific which we are going on. Hence, this study introduces the FEP integration methodology for generating scenarios based on the hybrid scenario development method using the FEP list.

The safe disposal of high-level radioactive waste has become a prominent global concern, necessitating rigorous safety assessments for deep geological disposal facilities. In Korea, crystalline rock with low-permeability is considered as the host rock for radioactive waste disposal, and fluid flow and solute transport in a low-permeability rock formation predominantly occur through interconnected fracture network. To analyze and predict fluid flow and solute transport behavior within the fractures, a comprehensive understanding of solute mixing at fracture intersections is crucial. However, difficulty in direct observation of the mixing processes occurring within microscale fracture intersections has led only to analytical and numerical studies, which requires thorough experimental study based on direct observations and measurements for a fundamental understanding of the mixing processes in fracture intersections. In this study, elaborate experiments are being prepared and conducted to measure the complex flow velocity/structure and solute concentration at rough-walled fracture intersections, using a microscale visualization technique of micro Particle Image Velocimetry (micro-PIV) system. Most analytical and numerical studies have shown that at high Peclet number (Pe) > 1,000, streamlinerouting model plays a major role in redistributing solutes at the fracture intersection, at which the mixing ratio converges to zero. As opposed to the conventional mixing model, our experiments found the rebounding of the mixing ratio in the inertial flow regime, indicating an enhanced solute mixing at the intersection. Flow visualization has demonstrated that the inertial flow features, such as the development of large-scale eddies and the straightening of main streamlines, enhance the physical mixing of solutes at rough-walled fracture intersections. The findings provide insights into the influence of fracture geometry on flow dynamics and its significant impact on solute mixing at fracture intersections.

The WRK (Waste Repository Korea bentonite) compacted bentonite medium has been considered as the appropriate buffer material in the Korean SNF (Spent nuclear fuel) repository site. In this study, hydraulic properties of the WRK compacted bentonite core (4.5 cm in diameter and 1.0 cm in length) as the buffer material were investigated in laboratory experiments. The porosity and the entry pressure of the water saturated core at different confining pressure conditions were measured. The average velocity of water flow in the WRK compacted bentonite core was calculated from results of the breakthrough curves of the CsI aqueous solution and the hydraulic conductivity of the core was also calculated from the continuous flow core experiments. Because various gases could be generated by continuous SNF fission, container corrosion and biochemical reactions in the repository site, the gas migration property in the WRK compacted bentonite core was also investigated in experiments. The gas permeability and the average of gas (H2) in the core at different water saturation conditions were measured. Laboratory experiments with the WRK Compacted bentonite core were performed under conditions simulating the DGR environment (confining pressure: 1.5- 20.0 MPa, injection pressure: 1.0-5.0 MPa, water saturation: 0-100%). The WRK Compacted bentonite core was saturated at various confining pressure conditions and the porosity ranged from 27.5% to 43.75% (average: 36.75%). The calculated hydraulic conductivity (K) of the core using experimental results was 8.69×10-11 cm/s. The gas permeability of the core when the water saturation 0~58 % was ranged of 19.81~3.43×10-16 m2, representing that the gas migration in the buffer depends directly on the water saturation degree of the buffer medium. The average gas velocity in the core at 58% of water saturation was 9.8×10-6 m/s, suggesting that the gas could migrate fast through the buffer medium in the SNF repository site. Identification of the hydraulic property for the buffer medium, acquired through these experimental measurements is very rare and is considered to have high academic values. Experimental results from this study were used as input parameter values for the numerical modeling to simulate the long-term gas migration in the buffer zone and to evaluate the feasibility of the buffer material, controlling the radionuclide-gas migration in the SNF repository site.

Spent nuclear fuel management is a high-priority issue in South Korea, and addressing it is crucial for the country’s long-term energy sustainability. The KORAD (Korea Radioactive Waste Agency) is leading a comprehensive, long-term project to develop a safe and effective deep geological repository for spent nuclear fuel disposal. Within this framework, we have three primary objectives in this work. First, we conducted statistical analysis to assess the inventory of spent nuclear fuel in South Korea as of 2021. We also projected future generation rates of spent nuclear fuels to identify what we refer to as reference spent nuclear fuels. These reference spent nuclear fuels will be used as the design basis spent fuels for evaluating the safety of the repository. Specifically, we identified four types of design basis reference spent nuclear fuels: high and low burnup from PLUS7 (with a 16×16 array) and ACE7 (with a 17×17 array) assemblies. Second, we analyzed radioactive nuclides’ inventory, activities, and decay heats, extending up to a million years after reactor discharge for these reference spent nuclear fuels. This analysis was performed using SCALE/TRITON to generate the burnup libraries and SCALE/ORIGEN for source term evaluation. Third, to assess the safety resulted from potential radioactive nuclides’ release from the disposal canister in future work, we selected safety-related radionuclides based on the ALI (Annual Limit of Intake) specified in Annex 3 of the 2019-10 notification by the NSSC (Nuclear Safety and Security Commission). Conservative assumptions were made regarding annual water intake by humans, canister design lifetime, and aquifer flow rates. A safety margin of 10-3 of the ALI was applied. We selected 56 radionuclides that exceed the intake limits and have half-lives longer than one year as the safety-related radionuclides. However, it is crucial to note that our selection criteria focused on ALI and half-lives. It did not include other essential factors such as solubility limits, distribution coefficients, and leakage processes. So, some of these nuclides can be removed in a specific analysis area depending on their properties.

This study investigates the behavior of bentonite, used as a buffer material in deep geological disposal systems, in the context of pore morphology under the influence of field-collected groundwater conditions. The bentonite was processed into block form using cold isostatic press (CIP) and subsequently analyzed for its pore morphology in situ using synchrotron X-ray computed tomography (CT) within the field-collected groundwater environment. Bentonite buffers play a critical role in deep geological disposal systems by preventing contact between disposal containers and groundwater. Bentonite typically exhibits swelling upon contact with water, forming few layers of water molecules between its structural layers. However, the presence of ions such as K+ and Cl- can lead to a sharp reduction in swelling pressure. Loss of swelling pressure could negatively impact the integrity of future deep geological disposal systems, making its assessment crucial. This study involves processing various types of bentonite, including natural Na-type bentonite, into block forms and subjecting them to exposure in both deionized water and field-collected groundwater conditions. Internal pore morphology changes were measured using Xray CT technology.

A disposal system for spent nuclear fuel mainly divides into two parts; Engineered barriers include spent nuclear fuel, canister, buffer and backfill and natural barriers mean a host rock surrounding engineered barriers. If radionuclides released from a repository, they can migrate to the ecosystem. Sorption plays an important role in retarding the migration of released radionuclides. Hence, the safety assessment for the disposal of a spent nuclear fuel should consider the migration and retardation of radionuclides in geosphere. Distribution coefficient is one of input parameters for the safety assessment. In this work, distribution coefficients for crystalline rock as a natural barrier were collected and evaluated for the purpose of safety assessment for the deep geological disposal of a spent nuclear fuel. The radionuclides considered in this work are as follows; alkali and alkaline earth metals (Cs, Sr, Ba), lanthanides (Sm), actinides (Ac, Am, Cm, Np, Pa, Pu, Th U), transition elements (Nb, Ni, Pd, Tc, Zr), and others (C, Cl, I, Rn, Se, Sn). The sorption of radionuclides is influenced by various geochemical conditions such as pH/carbonates, redox potential, ionic strength, radionuclide concentration, kinds and amounts of minerals, and microbes. For the evaluation of distribution coefficients, the data from Sweden (SKB), Finland (Posiva), Switzerland (Nagra), and Japan (JAEA) were collected, analyzed, and the recommended distribution coefficients have been suggested.

The thermal evaluations for the conceptual design of the deep geological repository considering the improved modeling of the spent fuel decay heat were conducted using COMSOL Multiphysics computational program. The maximum temperature at the surface of a disposal canister for the technical design requirement should not exceed 100°C. However, the peak temperature at the canister surface should not exceed 95°C considering the safety margin of 5°C due to several uncertainties. All thermal evaluations were based on the time-dependent simulation from the emplacement time of the canister to 100,000 years later. In particular, the heat source condition was set to the decay heat rate and axial decay heat profile of the PLUS7 fuel with 4.0wt% U-235 and 45 GWD/MTU. The thermal properties of the granitic rock in South Korea were applied to the host rock region. For the reference design case, the cooling time of the SNF was set to 40 years, the distance between the deposition holes 8 meters and that between the deposition tunnels 30 meters. However, the peak temperature at the canister surface at 10 years was 95.979°C greater than 95°C. This design did not meet the thermal safety requirement and needed to be modified. For the first modified case, when the distance between the deposition tunnels was set to 30 meters, three cooling time cases of 40, 50 and 60 years and five distances of 6, 7, 8, 9 and 10 meters between the deposition holes were considered. The design with the distances of 9 and 10 meters between the deposition holes for the cooling time of 40 years and all five distances for 50 and 60 years were less than 95°C. For the second modified case, when the distance between the deposition holes was set to 8 meters, three cooling time cases of 40, 50 and 60 years and five distances of 20, 25, 30, 35 and 40 meters between the deposition tunnels were considered. The design with the distances of 35 and 40 meters between the deposition tunnels for the cooling time of 40 years, the distances of 25, 30, 35 and 40 meters for 50 years and all five distances for 60 years were less than 95°C. As a result, the peak temperature at the canister surface decreased as the cooling time and the distance between the deposition holes and the tunnels increased.

In this study, a third metal layer with a higher corrosion potential than copper was introduced between the copper and cast iron layer to strengthen the corrosion resistance of the copper layer which is considered as a corrosion resistant barrier in the disposal container for spent nuclear fuel. Three types of corrosion-resistant metals, silver, nickel, and titanium, were selected as the intermediate insertion layer, and the galvanic specimens of two bonded metals were exposed to KURT (KAERI Underground Research Tunnel) groundwater and a high voltage of 1.0 V was applied to corrode the specimens at electrochemically accelerated condition. Corrosion of copper part was confirmed in Cu-Ti, Cu-Ni, and Cu-Ag galvanic specimens, but copper part was not corroded in Cu-Fe galvanic specimen. If the corrosion-resistant intermediate layer proposed in this study works properly, the local corrosion problem of copper disposal canister is expected to be some degree solved, which can apply to a welding part or a stress concentrated part.

Since the first operation of the Gori No. 1 nuclear power plant in Korea was started to operate in 1978, currently 24 nuclear power plants have been being operated, out of which 21 plants are PWR types and the rest are CANDU types. About 30% of total electricity consumed in Korea is from all these nuclear power plants. The accumulated spent nuclear fuels (SFs) generated from each site are temporarily being stored as wet or dry storage type at each plant site. These SFs with their high radiotoxicity, heat generating, and long-lived radioactivity are actually the only type of high-level radioactive waste (HLW) in Korea, which urgently requires to be disposed of in deep geological repository. Studies on disposal of HLW in various kind of geological repositories have been carried out in such countries as Sweden, Finland, United States, and etc. with their own methodologies and management policies in consideration of their situations. In Korea long-term R&D research program for safe management of SF has also been conducted during last couple of decades since around 1997, during which several various alternative type of disposal concepts for disposal of SNFs in deep geological formations have been investigated and developed. The first concept developed was KAERI Reference Disposal System (KRS) which is actually very much similar to Swedish KBS-3, a famous concept of direct disposal of SF in stable crystalline rock at a depth of around 500 m which has been regarded as one of the most plausible method worldwide. The world first Finnish repository which is expected to begin to operate sooner or later will be also this type. Since the characteristics of SF discharged from domestic nuclear reactors have been changed and improved, and burnup has sometimes increased, a more advanced deep geological repository system has been needed, KRS-HB (KRS with High Burnup SF) has been developed and in consideration of the dimensions of SNFs and the cooling period at the time point of the disposal time, KRS+, a rather improved disposal concept has also been subsequently developed which is especially focused on the efficient disposal area. Recently research has concentrated on rather advanced disposal technology focused on a safer and more economical repository system in recent view of the rapidly growing amount of accumulated SF. Especially in Korea the rock mass and the footprint area for the repository extremely limited for disposal site. Some preliminary studies to achieve rather higher efficiency repository concept for disposal of SF recently have already been emphasized. Among many possible ones for consideration of design for high-efficiency repository system, a double-layered system has been focused which is expected to maximize disposal capacity within the minimum footprint disposal area. Based on such disposal strategy a rather newly designed performance assessment methodology might be required to show long-term safety of the repository. Through the study some prerequisites for such methodological development has been being roughly checked and investigated, which covers FEP identification and pathway and scenario analyses as well as preliminary conceptual modeling for the nuclide release and transport in nearfield, far-field, and even biosphere in and around the conceptual repository system. Through the study such scenarios and models has been implemented to development of a safety assessment by utilizing GoldSim development tool for a rough quantitative comparison with existing disposal options and simple illustration purpose as well as for showing how to develop and implementation of the model to GoldSim templet.

The spent fuels derived from the nuclear reactor facilities may be finally disposed in a deep underground below 500 m. It majorly has uranium with minor iodine, which is a typical anionic radionuclide. In particular, radioiodine has higher mobility from its spent fuel source. It has been well known that it could freely pass through a compacted bentonite that is one of underground engineering barriers that are used to retard some nuclide’s migration from the spent fuel. We installed a small laboratory apparatus in an anaerobic glove box imitating such an underground repository and evaluated the iodine mobility in compacted bentonites with or without copper. Some copper-bearing bentonites were prepared in two types, a copper ion-exchanged form and a copper nanoparticle-mixed one. In our study, we tried to find an effect of sulfate that has an ability to retard mobile iodine from the compacted bentonite for a long-term period. Conclusively, we found an effective way to limit the iodine release from the compacted bentonite. This condition can be achievable by exchanging the bentonite interlayer cations with copper ions or by simply mixing copper nanoparticles with bentonite powder. In those cases, soluble iodine can be easily immobilized as a solid phase (i.e., marshite (CuI)) by combining with copper via the geochemical role of sulfate and indigenous SRB (sulfate reducing bacteria) of bentonite.

Even though a huge amount of spent nuclear fuels are accumulated at each nuclear power plant site in Korea, our government has not yet started to select a final disposal site, which might require more than several km2 surface area. According to the second national plan for the management of high-level radioactive waste, the reference geological disposal concept followed the Finnish concept based on KBS-3 type. However, the second national plan also mentioned that it was necessary to develop the technical alternatives. Considering the limited area of the Korean peninsula, the authors had developed an alternative disposal concepts for spent nuclear fuels in order to enhance the disposal density since 2021. Among ten disposal concepts shown in the literature published in 2000’s, we narrowed them to four concepts by international experiences and expert judgements. Assuming 10,000 t of CANDU spent nuclear fuels (SNF), we designed the engineered barriers for each alternative disposal concept. That is, using a KURT geological conditions, the engineered barrier systems (EBS) for the following four alternative concepts were proposed: ① mined deep borehole matrix, ② sub-seabed disposal, ③ deep borehole disposal, and ④ multi-level dispoal. The quantitative data of each design such as foot prints, safety factors, economical factors are produced from the conceptual designs of the engineered barriers. Five evaluation criteria (public acceptance, safety, cost, technology readiness level, environmental friendliness) were chosen for the comparison of alternatives, and supporting indicators that can be evaluated quantitatively were derived. The AHP with domestic experts was applied to the comparison of alternatives. The twolevel disposal was proposed as the most appropriate alternative for the enhancement of disposal efficiency by the experts. If perspectives changes, the other alternatives would be preferred. Three kinds of the two-level disposal of CANDU SNF were compared. It was decided to dispose of all the CANDU spent nuclear fuels into the disposal holes in the lower-level disposal tunnels because total footprint of the disposal system for CANDU SNF was much smaller than that for PWR SNF. Currently, we reviewed the performance criteria related to the disposal canister and the buffer and designed the EBS for CANDU SNF. With the design, safety assessment and cost estimates for the alternative disposal system will be carried out next year.

The presence of technological voids in deep geological repositories for high-level radioactive nuclear waste can have negative effects on the hydro-mechanical properties of the engineered barrier system when groundwater infiltrates from the surrounding rock. This study conducted hydration tests along with image acquisition and X-ray CT analysis on compacted Korean bentonite samples, which simulated technological voids filling to investigate the behavior of fracturing (piping erosion) and cracking deterioration. We utilized a dual syringe pump to inject water into a cell consisting of a bentonite block and technological voids at a consistent flow rate. The results showed that water inflow to fill technological voids led to partial hydration and self-sealing, followed by the formation of an erosional piping channel along the wetting front. After the piping channel generated, the cyclic filling-piping stage is characterized by the repetitive accumulation and drop of water pressure, accompanied by the opening and closing of piping channels. The stoppage of water inflow leads to the formation of macro- and micro cracks in bentonite due to moisture migration caused by high suction pressure. These cracks create preferential flow paths that promote longterm groundwater infiltration. The experimental test and analysis are currently ongoing. Further experiments will be conducted to investigate the effects of different dry density in bentonite, flow rate, and chemical composition of injected water.