이 연구는 철근 부식 문제의 해결 방안으로 떠오르고 있는 섬유복합체(Fiber Reinforced Polymer, FRP) 보강근에 대해 인장강도 추정식인 혼합법칙을 보정하여 FRP 보강근의 인장강도를 좀더 정확히 예측할 수 있는 방법론을 제안하는데 그 목적을 두었다.

The purpose of this experimental study is to evaluate that KCI2012 equation for the development length, ldt, of headed bars can be used to calculate the lap length of headed deformed bars in grade SD400~500 for high strength concrete. Test results showed that specimens with lap lengths equal to 1.3ldt had maximum flexural strengths as 0.84~0.90 times as the nominal flexural strengths. These observations indicate that 1.3 is unsuitable to the tensile lap length of headed deformed bars in grade SD400~500 for high strength concrete.

This paper evaluates the shear strength, behavior and failure mode of reinforced concrete beams with deformed GFRP reinforcing bar. Four concrete beam specimens were constructed and tested. It was carried out to observe failure behavior and load-deflection of simply supported concrete beams subjected to four-point monotonic loading. Load-deflection for FRP reinforced concrete beam member were predicted.

This study evaluated the fracture strength of GFRP-strengthened RC beams caused by the debonding failure of the GFRP. The fracture strength of RC beams calculated using FRP debonding strains suggested by several main design guidelines were higher than those of experiments. The result might indicate the need of some reduction in the values of the debonding strain or the strength reduction factor.

In this study it was developed FRP rod embedding FBG sensor, and compared the performance of sensor of the new rods and the existing strain gauge by applying the reinforced concrete beam-column joint in the same location. And it was found that new FRP rod was improved the structural performance and sufficiently sensing accuracy.

This paper describes the creep results of experimental testing of GFRP / Aluminum composite beam strengthened RC beams under the two different sustained loads. Specimens have been designed and fabricated to reflect the most common RC beams used in school buildings.

Fish passage asssessments were conducted in the fishway at Juksan Weir, which was constructed as a four-major rivers project in the downstream area of Youngsan-River Watershed. For the research, fish-movements/migrations were analyzed for seven times from April ~ October, 2013 using an approach of fish trap-setting. Fish fauna and compositions were analyzed in the fishway, and seasonal- and diel-movement patterns were analyzed in relation to current velocity in the fishway. Also, abundances of exotic fishes such as bluegill sunfish (Lepomis macrochirus), large-mouth bass (Micropterus salmoides), and white curcian carp (Carassius cuvieri) were monitored in the fishway. Current velocity(n = 18) in the fishway showed large variations (0.82 ± 0.63 m/s) depending on the location of the fish trap-setting and this physical factor influenced the fish movements. Fish movements, based on the CPUE of individuals, in the fishway was greater in slower velocity (mean: 0.36 m/s, range: 0.10~1.54 m/s) than faster velocity (mean: 1.51 m/s, range: 0.90~1.90 m/s). Seasonal analysis of fish movements showed that most frequent uses (8 speices and 591 individuals, 66.2% of the total) of the fishway occurred in spring period(i.e., June). Diel movement analysis, in the mean time, showed highest in the time period of 00:00 ~ 3:00 am (7 species and 281 individuals, 20.9% of the total). The efficient managements in the fishway at Juksan Weir are required in relation to the hydrological regime.

본 연구에서는 기존 철근콘크리트 건축물의 구조성능 개선을 위하여 표면요철 매입형 FRP봉과 CFRP시트를 사용한 철근콘크리트 보의 구조성능을 평가하기 위하여 실험을 수행하였다. 표면요철 매입형 FRP봉의 사용량, CFRP시트 보강 유무에 따라 총 7개의 실험체를 제작하고 실험을 수행하여 구조성능을 평가하였으며, 본 연구의 실험결과를 근거로 다음과 같은 결론을 얻었다. 표면요철 매입형 FRP봉 보강 실험체 NER 시리즈의 경우, 표준실험체 NBS와 비교하여 12~46% 내력이 증가하였고, 표면요철 매입형 FRP봉과 CFRP시트를 복합 보강한 실험체 NERL 시리즈는 표준실험체 NBS보다 최대내력이 22~77% 증가하였다. 그리고 표면요철 매입형 FRP봉으로 보강된 실험체 NER 시리즈는 부착슬립, 피복분리 형태로 파괴되었으나, 표면요철 매입형 FRP봉과 CFRP시트을 복합 보강한 실험체 NERL 시리즈는 CFRP시트의 연속보강에 따른 콘크리트 구속효과 및 모재와 표면요철 매입형 FRP봉의 부착강도 증가로 인하여 부착슬립의 형태로 파괴되었다.

GFRP 보강근의 역학적 성능은 고온과 콘크리트의 알칼리 환경에서 크게 감소된다. 본 연구에서는 GFRP 보강근이 열손상 뒤, 알칼리 환경에 추가로 노출되었을 때의 계면전단강도변화를 고찰하는데 집중하였다. 이를 위하여 GFRP 보강근 시편은 270도의 열에 1시간동안 노출된 후 알칼리 용액에 장기간 노출되었으며, 전단시험에 의하여 파괴되었다. 비교를 위하여 열손상이 없는 시편도 같은 기간 동안 알칼리 용액에 노출된 후 전단에 의하여 파괴되었다. 결과에서, 열손상을 받은 GFRP보강근의 계면전단강도의 감소가 열손상이 없는 보강근 보다 훨씬 큰 것으로 나타났다. 본 실험을 근거로 하여, 열손상을 미리 받은 GFRP 보강근이 알칼리에 노출되었을 때, 장기 잔존계면전단강도의 예측을 위한 2차식을 제시하였다.

본 연구의 목적은 고강도 SFRC 보의 강섬유 보강효과를 평가하기 위한 것이다. 이를 위하여 13개의 실험체를 제작하여 성능실험을 실시하였다. 실험 변수는 전단경간비, 강섬유 혼입률, 전단보강근비이며 콘크리트 강도는 60 MPa이다. 기존 연구결과와 재료 및 부재 실험결과에 대한 분석에 의하면, 전단경간비 2.5와 강섬유 혼입률 1.0%인 경우가 강섬유 보강효과가 최대로 발휘되는 것으로 평가되었다. 강섬유 보강 및 전단경간비를 고려한 기존 전단내력식은 고강도 SFRC보의 내력을 과소평가하는 것으로 평가되었다. 향후 고강도 SFRC 보의 강도특성에 대한 보완 연구가 필요한 것으로 판단된다.

본 연구에서는 기존 철근콘크리트 건물의 보-기둥 접합부의 내진성능의 개선을 위해 보-기둥 접합부 영역을 FRP보강재(매입형 CFRP Rod, CFRP시트)를 사용하여 보강한 후 내진성능을 평가하였다. 총 6개의 실험체를 제작하고 실험을 수행하여 내진성능을 평가하였으며, 본 연구의 실험결과를 근거로 다음과 같은 결론을 얻었다. 기존 철근콘크리트 보-기둥 접합부의 접합부 영역을 보강한 결과, 초기 재하시 접합부 영역의 균열억제 효과와 재하 전 과정을 통하여 보강재의 구속효과로 인하여 균열억제 효과가 커서 안정적인 파괴형태 및 내력향상 효과를 나타내었다. 매입형 CFRP Rod와 CFRP시트를 활용한 RC 외부 보-기둥 접합부 실험체 RBCJ-SRC2는 표준실험체 RBCJ와 비교하여 변위연성4, 7에서 각각 최대 내력은 1.97배, 에너지소산능력은 2.08배 증가하였다. 또한, 실험체 RBCJ-SR시리즈와 비교하여 최대내력이 1.09~1.11배 증가하였다. 그리고 실험체 RBCJ-CS, RBCJ-SR시리즈, RBCJ-SRC2는 변위연성 5, 6에서 표준실험체 RBCJ 보다 에너지소산능력이 1.10~2.30배 증가하였다. 그리고 에너지소산능력은 변위연성 4에서 13.0~14.4% 증가하였다.

In this study, experimental research was carried out to improve and evaluate the seismic performance of reinforced concrete beam-column joint using Groove and Embedding FRP Rod and CFRP Sheet in existing reinforced concrete building. Test result shows that retrofitting specimen(RBCJ-SR2, SRCB2) designed by the improvement of seismic performance of reinforced concrete beam-column joints load-carrying capacities were increased 1.78 ~ 2.29 times in comparison with the standard specimen.

In this paper, the seismic performance of framed building with porous hysteretic damping system is examined by comparing the beam-column stiffness ratio. Analytical results show that in case of maximum displacement, acceleration, and shear force, the decrease in ρ=2.00 is larger than the decrease in ρ=0.10. But results appeared differently according to a number of stories that damper installed.

In this study, experimental research was carried out to evaluate the structural performance of the reinforced concrete beam hybrid retrofitting with two materials(groove and embedding FRP rod, CFRP sheet) in existing reinforced concrete buildings. Test results showed that the maximum load carrying capacity of retrofitted specimens(NER1, NER1B, NER1L) were increased by 1.11 ~ 1.22 times respectively in comparison with the standard specimen NBS.

This study targets the development of technologies of reclaimed noise blocking engineering to improve endurance which may unify noise-blocking construction against noise and vibration and earthquake-preventive construction during rebuilding. This paper is to find the validity of construction methodology with RC beam additional materials to apply to slab and walls.

This paper describes the analysis results of coupling beams using steel fiber reinforced concrete for comparison with measure behaviors. Analysis is performed by the finite element analysis program, Vector 2. The results show possibility that relieve complex detail of diagonally reinforced coupling beam.

The purpose of this study was to analyze flexural behavior of concrete beams with steel bar and FRP reinforcement. An investigation was performed on the influence of the flexural stiffness, cracking, deflection behavior. Specimen with FRP reinforcement showed a higher strength than specimen with only steel bar. Concrete strength had an effect on improvement in flexural strength and ductile deformation.

In this study, the experiments were carried out in order that flexural behavior evaluated High-strength Concrete Beams reinfrced with FRP plates according ro replacement ration of recycled aggregate. As a result, maximum load was higher than existiong of unreinforced when the reinforced with FRP plates and no decrease in load about increased fo replacement ration of recycled aggregate. Some specimens was greater than ACI 440-2R referemce value.

In this paper, the effects of beam splice location on seismic performance of column-tree connections were experimentally and analytically evaluated. The study results showed very little difference between the results of analytical and those of experimental.

In this study, strain distribution of the beam end and the end of horizontal stiffener of high-strength steel beam-to-column connections was analyzed by finite element methods. According to the FEM results, applied stiffener method showed that it is available to relieve the strain of maximum stress point of beam member