이 연구는 3-(1,8나프탈이미도)프로필메타아크릴레이트(NIPM)와 GMA공중합체의 합성과 물성에 관한 과제로서 나프탈이미드 발색단을 가진 공중합체의 조성, 모노머 반응성비, 공명효과(Q)와 극성효과 (e), 형광특성 등을 조사하였다. Azobisisobutyronitronitryl(AIBN) 개시제와 dimethylformamide(DMF) 용매를 60℃에서 공중합하였다. Fineman-Ross(F-R)와 Kelen-Tṻdṏs(K-T)법으로 부터 단량체 반응성비를 구하였으며, r₁값이 r₂보다 크게 나타났다. NIPM이 공중합체내에서 GMA보다 더 많음을 알 수 있다. 380 nm에서 약한 분자 형광띠와 460 nm에서 강한 중합체 엑시머 형광띠가 나타났다.

본 연구에서는 가속된 이온이 전기장이 걸려있는 freestanding 단결정 실리콘 나노 박막에 충돌했을 때 발생하는 열-전계 전자 방출 특성을 여러 전계 및 열적 조건 아래 체계적으로 분석하였다. 이온 충돌에 의한 열-전계 전자 방출은 쇼트키 효과 (schottky effect)의 선형영역의 특성에 의해 예측된 바와 같이 전계의 세기가 증가할수록 선형적으로 증가했으며, 이온 충돌에 의해 발생하는 열에너지의 제곱에 비례하는 특성을 보여주었다. 이러한 특성들은 실리콘 나노 박막의 질량 분석기용 이온 검출기로의 사용 가능성을 보여준다.

본 연구는 고상폐기물인 준설토와 혼합물질인 점토 및 유리프리트를 이용하여 기능성을 갖는 건축자재용으로의 재활용 가능성을 검토하고자 실시되었다. D항만 준설토의 중금속 함량은 Zn이 526.0~13,150.1 mg/kg의 범위를 나타내는 등 심한 오염상태이었다. 준설토(30P)의 주요 화학조성은 SiO₂(48.30 wt%), Al₂O₃(16.60 wt%), CaO(10.10 wt%), Fe₂O₃(7.75 wt%)이었으며, 점토는 SiO₂가 70.82 wt%, Al₂O₃ 18.78 wt%, 유리프리트는 SiO₂가 71.75 wt%, CaO 13.99 wt%, Na₂O 8.51 wt% 함유되어 있었다. 준설토를 점토에 10~40 wt% 첨가한 후 1,000℃와 1,100℃에서 소성한 시편의 압축 강도는 각각 132.6~178.5 kgf/cm2와 581.2~793.7 kgf/cm²이었다. 준설토가 40 wt% 첨가된 경우 (SC46) 1,100℃에서 소성한 경우가 793.7 kgf/cm²로 1,000℃에서 소성한 경우의 153.0 kgf/cm² 보다 5배 이상 높게 나타나 1,100℃ 온도가 소성에 더 적합한 것으로 판단되었으며, KS 1종벽돌 기준을 만족시켰다. 또한, 시편의 용출시험 결과 폐기물관리법상 지정폐기물 판정기준치를 크게 하회하는 것으로 나타났다.

For this research, prepared water soluble milk casein resin and waterborne polyurethane-acrylic resin. Use these resin, this article has been analyzed about change of mechanical properties by increasing amount of casein resin in polyurethane-acrylic resin on coated leather. According to measure data for solvent resistance, WPA(waterborne polyurethane-acrylic resin) resin and WPA-C1, C2, C3(samples of polyurethane-acrylic resin with milk casein resin) had good property. As known in the results, increase of casein constant did not influence to big change of hybrid resin properties. As test of tensile strength, WPA had lowest tensile characteristic(1.598 kgf/㎟) and WPA-C3 had highest tensile characteristic(1.718 kgf/㎟). Also best properties of abrasion was WPA-C3(06.021 ㎎.loss). In elongation case, WPA had best properties(754 %) in this experiment.

In this research we extracted water-soluble collagen peptide from flatfish skin and compared it with commercially available collagen peptide extracted from Tilapia scale currently placed on the market in the aspect of physiochemical property. The physical property and nutritional components of FSCP appeared almost similarly to those of TSCP, and also in calorie, FSCP marking 3.82 Kcal showed no differences from TSCP marking 3.84 Kcal. As for forming amino acids, in aspartic acid, serine, histidine, tyrosine, methionine, FSCP had higher content than TSCP, but in OH-proline, proline and alanine FSCP had lower content than TSCP. Especially the content of essential amino acids of FSCP marked 22.74% with a higher content compared with 13.64% of TSCP. In the distribution of molecular weight FSCP with 1,000 Da showed omparatively low compared with TSCP, and in emulsion property and stability FSCP and TSCP showed similar excellent trend.

To investigate the adhesion effect of sodium bisulfite content in making blocked isocyanate, wood adhesive PB-1, PB-2, PB-3 and PB-4 containing sodium bisulfite content of 15%, 22.5%, 30% and 37.5% were synthesized respectively. As a result, when the amount of sodium bisulfite increased in adhesives, the tensile strength was found to be proportionally increased. The final adhesive mixtures were manufactured using a two-components system which are prepared by mixing two separate protein and BI solutions due to the precipitate in the adhesives. As PVA was added to adhesives to increase tenacity, the plywood dehiscence phenomenon after cold pressing process was declined. By addition of PVA, the tensile strength was improved up to 6.5~7kgf/cm2 with BI/protein ratio from 1:6 up to 1:8. Phase separation between milk fat and aqueous layer was disappeared after addition of emulsifier, Tween 20. Additon of Tween 20 showed tensile strength up to 5 ~ 6.5 kgf/cm2 at NCO/protein ratio of 1:12 ~ 1:14 without phase separation.

Various efforts have been explored to save the cost in many industrial fields. In order to recover the residual thermal energy from the flue gas, an extreme high efficiency heat exchanger is planning to install at a power plant. The gas temperature will be reduced to 40°C from 115°C. Thus gas buoyancy decreases, and dispersion of nitrogen oxides is expected to deteriorate as increasing relative humidity. In this study, the conversion of nitrogen monoxide to nitrogen dioxide and dispersion regime are investigated through computational modeling. Nitrogen dioxide which indicates 0.1 ppm at 85 m from the ground could be propagated to 620 m at 115°C of the flue gas, whilst when cooled down to 40°C, it expands up to 750 m. The ground level influence area showed more expansion of dispersion, approximately to 930 m.

Biodiesel is one of the most important renewable energy, since it is one of the most important alternative and eco-friendly energy source compared to fossil energy, especially for diesel engineequipped vehicles. It is now coming up for preparation of biodiesel as the alternative that applies the hetrogeneous catalyst, super critical state and various methods used in order to reduce the stages of the processes be converted and separation stages started from oil and fat which are originated from animals and wastes, and those new methods bring eco-friendly as well, though some of those are stand on research step so far. It is necessary that nation provides the tax exemption program for the supplier and strengthen the research system for the farming crops relate to fat and oil. It can improve the development of biodiesel which sustains stability against oxidation and keeps good mobility over the low temperatures in the winter season by new additives and develops new processes to show good harmony with diesel engine.

5,6-dihydroxyindole was easily oxidation with air and light Conditions. Availability of 5,6-dihydroxyindole was studied for hair dye as a precursor of melanin. This study used wet and dry coating process to stabilize 5,6-dihydroxyindole. In wet process used dimethicone and cyclometicone, the 5,6-dihydroxyindole had darkened through the drying process at 58℃. Wet coating process was inappropriate to stabilize the coating. In dry coating process, shea butter coating was stable until 3 days. Dextrin palmitate was most efficient ingredient to prevent oxidation by sun light and air until 7days. Oxidation test with 1.0% and 1.5% of dextrin palmitate was not different under conditions of sun light and air and was not dependent on contents. Vitamin E acetate under conditions of sun light and air, there were no significant effect in preventing oxidation.

The purpose of this study was to process extraction and separation for polyglucose porpyran from pophyra yezoensis as high yield. The acidic porphyran solution was extracted with 0.1∼1N of α,β-dichloromaleic acid or α-chloromaleic acid of 2% solution as organic acid instead of inorganic acid at 60℃ and then porphyran was collection of high yield to acidic solution and it was neutralization treated with 0.1N of d-Ca(OH)2 solution and the mixture was conversion to porphyran salt form and treated with a shell powder of ouster and then added of ethanol as precipitator. It recovery porphyran contained of violet purple laver coloring matter was obtained as a crystalline and used for the next step without future purification to prepare of porphyran laver jam. so, The resulting porphyran and porphyran jam was characterized by it component and physical properties.

In this study, CO₂ adsorbent was produced for minimizing energy loss due to ventilation within the building. For improved selectivity about low concentration of CO₂ in multiple-use facilities, the ball type adsorbent was modified from a commercial zeolite, alumina, alkali metals and activated carbon with mixing LiOH, binder, and H₂O. We measured specific surface area, pore characteristic, and crystal structure of the modified adsorbent. Effects of alkalization on the absorptive properties of the adsorbents were investigated. Continuous column tests (2,000 ppm) and batch chamber tests (4m3, 5,000ppm) showed that the modified adsorbent indicated about the selectivity of CO₂ more than 9.7% (0.613 mmol/g) compared with ordinary adsorbents and CO₂ removal efficiency of 88.8% within l hour, respectively. It was estimated that the modified adsorbent was applicable to indoor environments.

This study shows the effect of 4% squid ink on the textural properties of squid during fermentation for 8 weeks at 10℃ or 32 days at 20℃ in 5% salt solution. Although the hardness and chewiness of the squid fermented with squid ink continuously decreased during fermentation, the degree of decrease was smaller than that of squid fermented without squid ink. We can conclude that squid ink inhibited the ripening of the low salt fermented squid.

Bioenergy is classified to one of the renewable energy resources such as solar, wind, hydro and tidal energies. It should be noted that all the renewable energies contribute to the reduction of greenhouse gases emission. In some cases, energy from wastes was also categorized as a renewable energy in our country even though it has only negligible effect on the emission reduction. In this paper, we tried to identify the bioenergy in order to follow the global indices of the renewable energy. The indices evaluated here were whether a resource is renewable, iogenic, biodegradable, combustible and organic. Biogenic and combustible were selected as the indices to identify the bioenergy. It was also suggested that combustible as an index can be exchangeable to organic.

The conductive polymer composites recently became increasingly to many fields of industry due to their electrical properties. To understand these properties of composites, electrical properties were measured and were studied relatively. Electrical conductivity measurements showed percolation phenomena. Percolation theories are frequently applied to describe the insulator-to-conductor transitions in composites made of a conductive filler and an insulating matrix. It has been showed both experimentally and theoretically that the percolation threshold strongly depends on the aspect ratio of filler particles. The critical concentration of percolation formed is defined as the percolation threshold. This paper was to study epoxy resin filled with copper. The experiment was made with vehicle such as epoxy resin replenished with copper powder and the study about their practical use was performed in order to apply to electric and electronic industry as well as general field. The volume specific resistance of epoxy resin composites was 3.065~13.325 in using copper powder. The weight loss of conductive composites happened from 350℃~470℃.

Use of low bandgap polymers is the most suitable way to harvest a broader spectrum of solar radiations for solar cells. But, still there is lack of most efficient low bandgap polymer. In order to solve this problem, we have synthesised a new low bandgap polymer and investigated its interaction with the ILs to enhance its conductivity. ILs may undergo almost unlimited structural variations; these structural variations have attracted extensive attention in polymer studies. In addition to this, UV-Vis spectroscopy, confocal Raman spectroscopy and FT-IR spectroscopy results have revealed that all studied ILs (tributylmethylammonium methyl sulfate [N1444] MeSO4] from ammonium family) and 1-methylimidazolium chloride ([MIM]Cl, and 1-butyl-3-methylimidazolium chloride [Bmim]Cl from imidazolium family) has potential to interact with polymer. Further, protic ILs shows enhanced conductivity than aprotic ILs with low bandgap polymer. This study provides the combined effect of low bandgap polymer and ILs that may generate many theoretical and experimental opportunities.

NOx from the thermal power plants are NO and NO₂. This work investigated the chemical/physical characteristics and SCR efficiency of newly prepared catalysts including tungsten (WO₃), molybdenum (MoO₃) and antimony (SbO₃) based on vanadia(V₂O5) over titania(TiO2). As a result of the examination, the surface area of the catalysts promoted with additional metals was larger and the de-NOx efficiency also was enhanced with temperature. The most efficient catalytst was V₂O5/TiO₂-WO₃(10%) at 200 °C. Such a high efficiency could contribute to reduce the ammonia slip.

The influences of scatterer and absorber in turbid material by light scattering on silica fume of additive were interpreted for the scattered intensity and wavelength. The molecular properties have been studied by Monte Carlo simulation in resin of New Austria Tunnel Method. It has been found that the effects of optical properties in scattering media could be investigated by the optical parameters(μs, μa ,μt). Monte Carlo Simulation method for modelling of light transport in the civil engineering and construction field was applied. The results using a phantom were discussed that the distance from source to detector is closer, and scattering intensity is stronger with those obtained through Monte Carlo Simulation. It may also aid in designing the best model for coatings and corrosion for the durability of metal constructions.

Sulfur content of diesel fuel has been cut down to under 10 ppm ULSD (ultra low sulfur diesel) level by environmental regulation with the aim of reducing exhaust emissions. This review discusses the methods and principles of sulfur reduction in diesel and presents an overview of new approaches for ultra-deep desulfurization. The deep HDS (hydrodesulfurization) problems of diesel streams is exacerbated by the inhibiting effect of co-existing aromatics, nitrogen compounds and H₂S. The new approaches to deep desulfurization includes non-HDS type processing schemes such as adsorptive, extractive and oxidative desulfurization.

Carbon coils could be synthesized using C₂H₂/H₂as source gases and SF6 as an incorporated additive gas under thermal chemical vapor deposition (CVD) system. Prior to the carbon coils deposition reaction, two kinds of samples having different combination of Ni catalyst and substrate were employed, namely, a commercially-made Al₂O₃ceramic boat with Ni powders and a commercially-made Al₂O₃substrate with Ni layer. By using a commercially-made Al₂O₃ceramic boat, the synthesis of carbon coils could be enhanced as much as 10 times higher than that of Al₂O₃substrate. Furthermore, the dominant formation of the microsized carbon coils could be obtained by using Al₂O₃ceramic boat. The surface roughness of the supporting substrate of Al₂O₃ceramic boat was understood to be associated with the large scale synthesis of carbon oils as well as the dominant formation of the larger-sized, namely the microsized carbon coils.

Polymers in cosmetics are used to deliver desired attributes to skin and hair. Precisely constructed block and graft copolymers widen the range of available mechanical properties and compatibilities. Stimuli responsive hydrophobic polymers can be triggered to become hydrophilic by changes in their environment and this can confer waterproof properties at low temperature and easy water removal at higher temperatures. Transfer-resistant cosmetics can be possible due to silicone resins. The control of rheology properties in cosmetics gradually continue to be easy with copolymers. Durability of colors and fragrances for rinse-off products can be enhanced by delivery systems from complex coacervates. Polymeric anti-microbials promise product preservation while minimizing the concern of skin permeation. This article reviews recent trends in the use of polymers in cosmetics.