Response modification factors of school facilities for non-seismic RC moment frames with partial masonry infills in ‘Manual for Seismic Performance Evaluation and Retrofit of School Facilities’ published in 2018 were investigated in the preceding study. However, since previous studies are based on 2D frame analysis and limited analysis conditions, additional verification needs to be performed to further apply various conditions including orthogonal effect of seismic load. Therefore, this study is to select appropriate response modification factors of school facilities for non-seismic RC moment frames with partial masonry infills by 3D frame analysis. The results are as follows. An appropriate response modification factor for non-seismic RC moment frames with partial masonry infills is proposed as 2.5 for all cases if the period is longer than 0.6 seconds. Also if the period is less than 0.4 seconds and the ratio of shear-controlled columns is less than 30%, 2.5 is chosen too. However, if the period is less than 0.4 seconds and the ratio of shear-controlled columns is higher than 30%, the response modification factor shall be reduced to 2.0. If the period is between 0.4 and 0.6 seconds, then linearly interpolates the response correction factor.

본 연구에서는 충청북도 충주시를 대상으로 폭염시 토지이용유형별 보행공간의 기상특성과 공기이온 특성을 측정 및 분석하였다. 연구대상지 보행공간의 토지이용유형 구분은 지적편집도를 이용하여 대상지를 크게 Green Area, Residential Area, Commercial Area으로 실시하였다. 측정지점은 약 4.1km, 44개 지점으로 측정지점을 선정하여 외곽지 역 관통도로 보행공간 Green Area 12개 지점, Residential Area 14개 지점, Commercial Area 18개 지점으로 구분하여 측정하였다. 또한 폭염시 토지이용유형별 보행공간의 기온, 상대습도, 일사량, 순복사량 등의 기상요소가 음이온 발생량, 양이온 발생량에 미치는 영향을 분석하여 이온지수를 산출하였다. 폭염시 토지이용유형별 보행공간의 공기이온 특성 비교결과 평균 양이온 발생량은 Commercial Area(700.73ea/cm3) > Residential Area(600.76ea/cm3) > Green Area(589.73ea/cm3)로 분석되었다. 평균 음이온 발생량은 Green Area(663.95ea/cm3) > Residential Area(628.48ea/cm3) > Commercial Area(527.48ea/cm3) 로 분석되었다. 평균 이온지수는 Green Area(1.13) > Residential Area(1.04) > Commercial Area(0.75)로 분석되었다. 본 연구는 폭염시 토지이용유형별 보행공간에 따른 기상특성, 양이온 발생량과 음이온 발생량 현황을 확인할 수 있었으며, 토지이용유형별 보행공간의 이온지수의 차이를 확인할 수 있었다. 그러나 이동측정에 따른 토지이용유형별 정확한 비교 부족과 도로 폭 변화에 대한 정량적 특성 비교가 부족한 한계점이 존재하였 다. 따라서 도로 특성을 고려한 지속적인 연구가 이루어져야할 것으로 판단되었다.

본 연구는 태백산국립공원 백두대간 생태축 연결을 위한 평가항목 및 요인별 가중치 설정을 위해 공원관리와 생태계 조사, 생태환경계획과 관련된 분야별 전문가 대상의 설문조사를 토대로 계층화 분석을 실시하였다. 문헌연구와 담당자 면담조사로 생태축 연결을 위한 상위 평가지표 4개와 하위 평가지표 13개를 선정하였으며, 일관성 분석에 의한 유효 설문을 대상으로 항목별 가중치를 산정하였다. 분석결과, 상위평가 지표에서는 생태계 가치증진이 0.474로 가장 높고, 자연-인간 갈등완화(0.247), 지역주민의 참여(0.165), 경제적 측면(0.114) 순으로 나타났으며, 하위 평가지표에서는 생물이동경로(0.116), 경관생태적 패치 연결성(0.112), 기능적 서식지(0.099) 등이 중요 항목으로 추출되었다. 분야별 평가항목과 가중치 비교에 따르면 생태계조사 분야에서는 생물종 이동경로(0.116)을 가장 중시하는 반면, 공원관리 분야에서는 기능적 서식지가 0.110로 가장 중요한 항목으로 평가되었으며, 생태환경계획 분야에서는 지역의 보전 및 이용자원 분포현황이 0.123으로 가장 높게 나타났다. 본 연구결과는 태백산국립공원 일대의 생태축 연결에 필요한 조사항목의 선정이나 분야별 연결성 분석방향 설정에 기여할 것이다.

목적 : 본 연구는 목욕서비스 제공자의 편의성, 업무효율성, 안전성 증진을 통한 근골격계질환 발생 위험성 예방 및 감소시킬 수 있는 이동형 목욕보조기기 개발과 이의 효과성 검증에 목적을 두었다. 연구방법 : 목욕서비스 제공자는 광역시 소재 요양병원에서 근무하는 간병인, 요양보호사 24명을 대상으로 하였다. 연구도구는 목욕서비스 제공자와 전문가집단의 의견수렴을 거쳐 개발한 이동형 목욕보조기기 프로토타입을 사용하였다. 사전평가로 Rapid Entire Body Assessment(REBA), Visual Analogue Scale(VAS)를 하였으며, 사후평가로 REBA, VAS, Korean version of Quebec User Evaluation of Satisfaction Assistive Technology(K-QUEST 2.0), 사용자의 주관적 의견을 설문조사하였다. 사용 전후의 REBA와 VAS를 비교하기 위해 t-test로 분석하였으며, 상관관계를 알아보기 위해 pearson 상 관분석을 하였다. 일반적 특성과 종속변수 간의 분석을 위해 ANOVA를 실시하였다. 결과 : 이동형 목욕보조기기 프로토타입을 사용 후 평가결과, 2가지 자세(목욕용품 사용, 샤워기 사용)에서 측정되었던 REBA 조치수준이 ‘높음’에서 ‘낮음’으로 변경되었다. 통증 정도는 보조기기 사용 후 팔을 제외한 모든 항목에서 감소되었으며 전체 평균점수는 통계적으로 유의한 차이를 보였다. 사용 후 만족도 에서는 규격과 무게를 제외한 6개 항목에서 ‘보통’으로 나타났다. 사용 전·후에 따른 종속변수들 간의 상관관계 분석 결과에서는 높은 상관성을 보이지 않았으며 일반적 특성과 종속변수 간의 통계적 유의성 은 없는 것으로 나타났다. 결론 : 본 연구에서 최종 개발한 이동형 목욕보조기기는 목욕서비스 제공자의 신체적 부담을 줄일 수 있을 뿐만 아니라 편의성, 효율성, 안전성도 증진시킬 수 있는 보조기기로서의 역할이 가능하다고 예상된다.

Seismic performance of ordinary reinforced concrete shear wall systems commonly used in high-rise residential buildings is evaluated. Three types of shear walls exceeding 60m in height are designed by performance-based seismic design. Then, incremental dynamic analysis is performed collapse probability is assessed in accordance with the procedure of FEMA P695. As a result, story drift, plastic rotation, and compressive strain are observed to be major failure modes, but shear failure occur little. Collapse probability and collapse margin ratio of performance groups do not meet requirement of FEMA P695. It is observed that critical wall elements fail due to excessive compressive strain. Therefore, the compressive strain of concrete at the boundary area of the shear wall needs to be evaluated with more conservative acceptance criteria.

본 연구에서는 한국 자동차 부품 업체를 대상으로 완성차 업체의 해외 동반진출과 성과 간의 관계에 대해 실증 적으로 분석하고 이러한 관계가 전속적 거래 관계에 의해 어떻게 달라지는지를 설명하고자 한다. 2004년부터 2016년까지 105개 사의 패널 데이터를 구성하여 실증분석을 한 결과, 국내 자동차 부품회사의 해외직접투자에 있어서 완성차 업체와의 동반진출이 성과에 미치는 영향은 비동반진출보다 컸으며, 동반진출이 성과에 미치는 긍 정적 영향은 그 횟수가 증가할수록 감소하였다. 이러한 결과는 자동차 부품 업체가 대기업과의 동반진출을 통해 초기 납품 물량을 안정적으로 보장받을 수 있을 뿐만 아니라 파트너가 보유한 네트워크를 통해 초기에는 빠르게 성장할 수 있지만, 동반 진출 횟수가 많아질수록 조직 복잡성으로 인한 조정 비용의 증가로 인해 이익의 폭이 줄 어들 수 있음을 나타낸다. 마지막으로 동반 진출과 성과 간의 관계에서 완성차 업체에 대한 전속적 관계가 두 변 수간 관계를 더 강화시키는 것으로 나타났다. 본 연구는 국내 자동차 부품기업들의 동반진출효과를 실증적으로 분석함에 따라 한국 자동차 산업 및 중소기업의 국제화 전략에 유용한 이론적, 실무적 시사점을 제시한다.

This study is aimed to take a stock assessment of blackthroat seaperch Doederleinia seaperch regarding the fishing effort of large-powered Danish Seine Fishery and Southwest Sea Danish Seine Fishery. For the assessment, the state-space model was implemented and the standardized catch per unit effort (CPUE) of large powered Danish Seine Fishery and Southwest Sea Danish Seine Fishery which is necessary for the model was estimated with generalized linear model (GLM). The model was adequate for stock assessment because its r-square value was 0.99 and root mean square error (RMSE) value was 0.003. According to the model with 95% confidence interval, maximum sustainable yield (MSY) of Blackthroat seaperch is from 2,634 to 6,765 ton and carrying capacity (K) is between 33,180 and 62,820. Also, the catchability coefficient (q) is between 2.14E-06 and 3.95E-06 and intrinsic growth rate (r) is between 0.31 and 0.72.

In this study, Al-Si-Mg alloys are additively manufactured using a selective laser melting (SLM) process from AlSi10Mg powders prepared from a gas-atomization process. The processing parameters such as laser scan speed and laser power are investigated for 3D printing of Al-Si-Mg alloys. The laser scan speeds vary from 100 to 2000 mm/ s at the laser power of 180 and 270W, respectively, to achieve optimized densification of the Al-Si-Mg alloy. It is observed that the relative density of the Al-Si-Mg alloy reaches a peak value of 99% at 1600 mm/s for 180W and at 2000 mm/s for 270W. The surface morphologies of the both Al-Si-Mg alloy samples at these conditions show significantly reduced porosities compared to those of other samples. The increase in hardness of as-built Al-Si-Mg alloy with increasing scan speed and laser power is analyzed due to high relative density. Furthermore, it was found that cooling conditions after the heat-treatment for homogenization results in the change of dispersion status of Si phases in the Al-Si matrix but also affects tensile behaviors of Al-Si-Mg alloys. These results indicate that combination between SLM processing parameters and post-heat treatment should be considered a key factor to achieve optimized Al-Si alloy performance.

It is well known that lymph node metastasis is a major prognostic factor in patients with oral squamous cell carcinoma (OSCC). 30-40% of patients with OSCC have already undergone regional metastasis at diagnosis. The survival rate of patients with metastasis is reduced by more than 50%. Therefore, prevention and early detection of metastasis are very important to increase the survival rate of patients. Many investigators have studied the molecular mechanism of metastasis and tried to develop the molecules to inhibit any step of metastatic cascade. Among those molecules, an interest in the metastasis suppressor gene has been increasing. Expression of metastasis suppressor KiSS-1 has shown to be significantly related to poor clinical outcome and worse survival rate of patient in various malignancies of different organs. In addition, our previous study in OSCC also revealed that downregulation of KiSS-1 expression correlated with the presence of cervical lymph node metastasis, one part of tumor progression. Therefore, further investigation was needed to identify the molecular function of KiSS-1 using OSCC cell line and to evaluate the possibility of KiSS-1 as a new therapeutic target.

Recently, copper alloy netting has been proposed as a material for aquaculture facilities that can be set in harsh offshore environments. To design a cage made of copper alloy netting, it is necessary to calculate the flow of water through the netting and force of external sources on the netting. Therefore, this study measured and analyzed the current velocity reduction after passing through the netting and the hydrodynamic forces acting on the netting using copper alloy netting with nine solidity ratios. As a result of the reduction rate of the flow velocity through the netting, the flow reduction rate was increased as the solidity ratio of netting was increased. The flow reduction rate was also increased as the attack angle on the netting was decreased. In analyzing the resistance on the netting, we also discovered that resistance was increased with increase in the flow velocity and solidity ratio. An analysis of the hydrodynamic coefficient acting on the netting is shown that the drag coefficient tends to increase as the attack angle increases. We also analyzed the hydrodynamic coefficient according to the variation of the Reynolds number. When the drag coefficients acting on the netting were analyzed with the different Reynolds numbers, the Reynolds number increased from over 0.3 m/s to a relative constant. Finally, the copper alloy nettings had a smaller velocity reduction rate when comparing the flow velocity reduction rate between copper alloy nettings and nylon nettings.

The concern on the greenhouse gas emissions is increasing globally. Especially, the greenhouse gas emission from fisheries is an important issue from the Paris Climate Change Accord in 2015. Furthermore, the Korean government has a plan to reduce the GHG emissions as 4.8% compared to the BAU in fisheries until 2020. However, the investigation on the GHG emissions from Korean fisheries rarely carried out consistently. Therefore, the quantitative analysis of GHG emissions from Korean fishery industry is necessary as a first step to find a relevant way to reduce GHG emissions from fisheries. The purpose of this research is to investigate which degree of GHG emitted from the major offshore fisheries such as offshore gillnet fishery, offshore longline fishery, offshore jigging fishery and anchovy drag net fishery. Here, we calculated the GHG emissions from the fisheries using the Life Cycle Assessment method. The system boundary and input parameters for each process level are defined for the LCA analysis. The fuel use coefficients of the fisheries are also calculated according to the fuel type. The GHG emissions from sea activities by the fisheries will be dealt with. Furthermore, the GHG emissions for the unit weight of fishes are calculated with consideration to the different consuming areas as well. The results will be helpful to understand the circumstances of GHG emissions from Korean fisheries

Most school buildings consist of reinforced concrete (RC) moment frames with masonry infills. The longitudinal direction frames of those school buildings are relatively weak due to the short-column effects caused by the partial masonry infills and need to be evaluated carefully. In ‘Manual for Seismic Performance Evaluation and Retrofit of School Facilities’ published in 2018, response modification factor of 2.5 is applied to non-seismic RC moment frames with partial masonry infills, but sufficient verification of the factor has not been reported yet. Therefore, this study conducted seismic performance evaluation of planar RC moment frames with partial masonry infills in accordance with both linear analysis and nonlinear static analysis procedures presented in the manual. The evaluation results from the different procedures are compared in terms of assessed performance levels and number of members not meeting target performance objectives. Finally, appropriate response modification factors are proposed with respect to a shear-controlled column ratio.