KEPCO KPS is the contractor for the full system decontamination (FSD) of Kori Unit 1 and under preparation such as modification, lay out for equipment installation, setting up tie-in/out point for chemical injection and way to pressurize the system, of its successful performance. In this research, KPS introduced how KPS has designed and prepared for the FSD project and how will the chemical decontamination process be implemented. As described in the previous research, chemical decontamination process is planned to be conducted for three cycles and each cycle is consisted of oxidation, reduction, decomposition, and purification. Oxidation and reduction process were conducted at 90°C. Chemical decomposition and purification process were conducted at 40°C due to the damage of IX by the heat. If the decontamination result does not meet the target DF and the dose rate, additional cycle can be conducted. Expected volume of process water for FSD is 200 m3. Three systems have been designated as decontamination targets: reactor coolant system (RCS), residual heat removal system (RHRS), chemical volume control system (CVCS). For the steady flow rate, existed plant equipment such as reactor coolant pump (RCP) will be operated and modifications on some components will be conducted. Due to the limited space for installation, decontamination equipment and other resources are distributed to three different places. KPS designed the layout of equipment installed inside the containment vessel. The layout contains the information of shielding for highly radiated equipment such as IX and filter skid.

Tc-99 is considered as one of the major fission products in the context of disposal of spent nuclear fuel, due to the long half-life and chemical stability. In the atmospheric aqueous solutions, Tc is expected to exist in the form of TcO4 ‒ and thus is considered as an environmental concern according to its high solubility and mobility. Therefore, the development of an effective and economically viable adsorbent for aqueous Tc(VII) is imperative from the perspective of decontamination and remediation of contaminated environments. In this work, the adsorption behaviors of Re(VII), as a chemical surrogate of Tc(VII), onto the bentonites modified with two different organic cations such as hexadecyl pyridinium (HDPy) and hexadecyl trimethylammonium (HDTMA) were quantitatively analyzed and compared with each other. For the sorption experiment, adsorbents were prepared by surface modification of bentonite. Before the modification, the initial bentonite was pre-treated with 1 M NaClO4 and then reacted with HDPy or HDTMA. The modification process was performed at room temperature for 24 hours with various concentrations of organic cations, which were set to a range of 50-400% compared to the cation exchange capacity (CEC) of bentonite. After the reaction, the dried and crushed modified bentonites were filtered with the sieve with a mesh size of 63 μm. Aqueous Re(VII) solutions were prepared by dissolution of NH4ReO4 (Sigma-Aldrich) in deionized water with three different Re(VII) concentrations of 10-4M, 10-5M, and 10-6M. After that, the modified bentonite and the aqueous Re(VII) solutions were mixed at a liquid-to-solid ratio of 1 g/L. Aliquots of the samples were extracted for quantification analysis with ICP-MS after syringe filtration (pore size: 45 μm) at reaction times of 10, 50, 100, and 500 minutes. According to the results, a considerably fast adsorption reaction of Re(VII) onto all modified bentonites was observed, revealing exceptional sorption affinity of HDPy- and HDTMA-modified bentonites. For both organic cations, bentonites modified with the concentrations of organic cations ranging from 200 to 400% relative to the CEC of bentonite showed almost complete removal of aqueous Re(VII). For bentonites modified with lower concentrations of organic cations, the HDTMA presented a relatively larger sorption capacity than the HDPy. The result obtained through this study is expected to be referred to as a case study for the synthesis of cost-efficient and highly effective adsorbent material for highly mobile anionic radionuclides such as I‒ and TcO4 ‒.

Thermal cutting processes that can be applied to dismantling nuclear power plants include oxygen cutting, plasma cutting, and laser cutting. According to the global trend, research projects are being carried out in various countries to upgrade laser cutting, and many studies are also being conducted in Korea with plans to apply laser cutting processes when dismantling nuclear power plants. However, with the current technology level of the laser cutting process, the maximum thickness that can be cut is limited to 250 mm. Therefore, in this study, a laser-oxygen hybrid cutting process was implemented by adding a laser heat source to the oxygen cutting process that can cut carbon steel with a thickness of 250 mm or more (RV, beam, column, beam, etc.) when dismantling the nuclear power plant. This has the advantage of improving the cutting speed and reducing the cutting width Kerf compared to conventional oxygen cutting. In this research, the laser-oxygen hybrid cutting process consisted of laser cutting to which Raycus’ 8 kW Fiber Laser power source was applied and oxygen cutting to which hydrogen was applied with Fuel Gas. The oxygen torch was placed perpendicular to the test piece, and the laser head was irradiated by tilting 35° to 70°. The effects of cutting directions on quality and performance were studied, and cutting paths were selected by comparing cutting results. Thereafter, it was confirmed that there is an optimal laser output power according to the cutting thickness by studying the effect on the cutting surface quality by changing only the laser output power under the same cutting conditions. The results of this study are expected to be helpful in the remote cutting process using laser-oxygen hybrid cutting when dismantling domestic nuclear power plants in the future.

As the decommissioning of domestic nuclear power plants (Gori Unit 1 and Wolseong Unit 1) becomes more visible, many research projects are being conducted to safely and economically decommissioning of domestic nuclear power plants (NPPs). After permanent shutdown, decommissioning of NNPs proceeds through decontamination, cutting of main equipment, waste disposal and site restoration stages. And various technologies are applied at each stage. In particular, remote cutting of neutron induced structures (RV, RVI, etc.) is a technology used in developed countries in the cutting stage, and remote cutting has been evaluated as a core technology for minimizing workers’ radiation exposure. Generally, remote cutting technologies are divided into mechanical/thermal/electrical cutting. Among various thermal cutting technologies, plasma arc cutting (PAC) is more economical and easily to remote control than other cutting technologies, and is also effective in cutting STS304 plates. PAC is a thermal cutting technology that melts the base material at the cutting area with a plasma arc heat source and removes melted material by blowing it out with cutting gas. The cutting quality depends on the stand-off distance and power (current), material thickness, cutting speed, etc., while double arcing will occur if the cutting conditions are not suitable. A monitoring system that can confirm double arcing during remote cutting is necessary because double arcing can reduce cutting quality, increase secondary waste (increase kerf and aerosol), and cause non-cutting. In this study, we used an ultrahigh-speed camera equipped with a band-pass filter to capture clear arc shapes, and measured voltage waveforms with a data acquisition system. We studied a monitoring method that can confirm the occurrence of double arcing by synchronizing the obtained arc shape and voltage waveform, and the effects of double arcing on the STS304 plates. The results of this study are expected to be helpful in the development of the remote cutting process using plasma arc cutting when decommissioning of domestic NPPs.

Heavy water primary system decontamination technology is essential to reduce worker exposure and improve safety during maintenance and decommissioning of nuclear facilities. Advanced decontamination technology development aims to secure controlled decontamination technologies that can reduce the cost of radiation exposure and dramatically reduce the amount of secondary waste generated when decontaminating large equipment and large-area facilities. We conducted a study to identify candidate corrosion inhibitors through the literature and analyze the degree of corrosion of carbon steel samples. Countries with advanced nuclear technology have developed chemical decontamination technology for the entire nuclear power generation system and applied it to the dismantling and maintenance of nuclear power plants. In the decontamination process, the corrosion oxide film must be removed. If the base metal is corroded by the decontaminant in this process, additional secondary waste is generated and treatment costs increase. Therefore, it is necessary to develop a corrosion inhibitor that inhibits the corrosion of the carbon steel base metal in the decontamination process to generate a secondary waste liquid that is favorable for waste reduction and treatment. In this presentation, a study was conducted to analyze the extent of corrosion on a carbon steel base material and identify candidate materials for corrosion inhibition testing. Samples were analyzed using optical microscopy and EPMA analysis to determine the thickness of the corroded oxide film. EPMA analysis also allowed us to map the elemental distribution of the carbon steel corrosion layer, which we plan to quantify in the future. The candidate materials for organic-based corrosion inhibitor were also selected based on their inhibition mechanism; having high electronegative elements for coordinate covalent bonding at metal surface and hydrophobic nonpolar group for preventing access of corrosive substances.The selection of candidate materials for corrosion inhibition testing was based on the mechanism of the corrosion inhibitor. Organic-based corrosion inhibitors are adsorbed by donor-acceptor interactions between metal surfaces and highly electronegative elements. Corrosion can also be inhibited by arranging hydrophobic nonpolar groups on metal surfaces in the solution direction to prevent access of corrosive substances.

When dismantling a power plant, a large amount of radioactive tanks are generated, and it is estimated that a significant amount of sludge will accumulate inside the tanks during long-term operation. In the process of dismantling a radioactive tanks, it is important to know the composition of the sludge because the sludge present inside must first be removed and then disposed of. In the case of certain tanks, it can be predicted that corrosion products generated due to system corrosion are the main cause of sludge formation. However, in the case of some tanks, it is not easy to predict the sludge composition because various dispersed particles in addition to corrosion products may be mixed with the wastewater. Even if it is collected and analyzed, the sludge composition can change significantly depending on the operation history, so the analysis results cannot be considered representative of the composition. In the case of LHST, surfactant components introduced during the washing and shower process, oil components and dispersed particles dissolved by the surfactant accumulate inside the tank, making sludge difficult to remove. In addition, even if it is removed by ultra-high pressure spraying, unexpected problems may occur in the subsequent treatment process due to the surfactant contained therein. Therefore, it is necessary to analyze in more detail the characteristics of sludge accumulated in LHST and prepare countermeasures. A test procedure was prepared to evaluate the characteristics of sludge accumulating in LHST. According to the test results, the long-term sludge accumulation tendency of the LHST is summarized as follows. ① Initially, the sludge settling speed increases slowly until a surface sludge layer is formed. ② After the surface sludge layer is formed, the sludge rapidly settles until the sludge layer becomes somewhat thicker. ③ When the sludge layer is formed to a certain extent, the sludge escape rate increases and the sludge accumulation rate decreases again. It is assumed that the sludge escape speed is closely related to the fluid flow speed in the relevant area. It is believed that the combined effect of these phenomena will determine the thickness of the sludge layer that will accumulate inside the tank, but it was not possible to evaluate how much the sludge layer would accumulate based on the experimental results alone. However, it can be assumed that significant sludge accumulation occurred in areas where fluid flow was minimal and sludge formation nuclei easily accumulates.

The domestic Pressurized Heavy Water Reactor (PWHR) nuclear power plant, Wolsong Unit 1, was permanently shut down on December 24, 2019. However, research on decommissioning has mainly focused on Pressurized Water Reactors (PWRs), with a notable absence of both domestic and international experience in the decommissioning of PHWRs. If proper business management such as radiation safety and waste is not performed, it can lead to increased business risks and costs in decommissioning. Therefore, the assessment of waste volume and cost, which provide fundamental data for the nuclear decommissioning process, is a crucial technical requirement before initiating the actual decommissioning of Wolsong Unit 1. Decommissioning radiation-contaminated structures and facilities presents significant challenges due to high radiation levels, making it difficult for workers to access these areas. Therefore, technology development should precede decommissioning process assessments and safety evaluations, facilitating the derivation of optimal decommissioning procedures and ensuring worker safety while enhancing the efficiency of decommissioning operations. In this study, we have developed a program to estimate decommissioning waste amounts for PHWRs, building upon prior research on PWR decommissioning projects while accounting for the specific design characteristics of PHWRs. To evaluate the amount of radioactive waste generated during decommissioning, we considered the characteristics of radioactive waste, disposal methods, packaging container specifications, and the criteria for the transfer of radioactive waste to disposal operators. Based on the derived algorithm, we conducted a detailed design and implemented the program. The proposed program is based on 3D modeling of the decommissioning components and the calculation of the Work Difficulty Factor (WDF), which is used to determine the time weighting factors for each task. Program users can select the cutting and packaging conditions for decommissioning components, estimate waste amount based on the chosen decommissioning method, and calculate costs using time weighting factors. It can be applied not only to PHWRs, but also to PWRs and non-nuclear fields, providing a flexible tool for optimizing decommissioning process.

Kori Unit 1, pressurized water reactor, is the Korea’s first commercial nuclear power plant. It successfully generated electricity for a period of 30 years, commencing from April 19, 1978. Following its approval for continued operation in 2008, Kori Unit 1 continued to operate for an additional 9 years, resulting in a total operational period of 39 years. On June 18, 2017, Kori Unit 1 was permanently shut down. Since then, Korea is actively preparing for the decommissioning of nuclear power plant. During the decommissioning of a nuclear power plant, the heavy components such as reactor, steam generator, pressurizer, reactor coolant pump located in the containment building should be taken out of the containment building. To take out heavy components from the containment building, pipes connected to heavy component should be cut. There are numerous pipes connected to the heavy component, each with varying dimensions and material. Each pipe has a different level of contamination depending on its use. In this study, optimal cutting method of pipe connected to steam generator, one of the heavy components of nuclear power plant, is proposed during the decommissioning of Kori unit 1. In case of pipe connected to Kori unit 1 steam generator, material is stainless steel or carbon steel. These pipes have varying inner diameter, ranging from 0.6 cm to 74 cm, and thickness ranging from 0.15 cm to 7.1 cm. These pipes are classified as low and intermediate level waste (LILW) or very low level waste (VLLW). Because characteristics of pipes are different, each pipe optimal cutting methods are proposed differently considering material, dimension, contamination level, cutting cost, cutting time, and the management of secondary waste. As a result, the cutting method for pipe of reactor coolant system is selected to orbital cutting. The cutting method of main steam pipe and main feedwater pipe is selected to oxygen cutting. In case of other small pipes, cutting method is selected to circular saw.

After the Fukushima accident in 2011, relevant concerns regarding the contamination of the natural environment rose abruptly. For example, water contaminated by radionuclides such as Cs and Sr may directly flow into the ocean and threaten the marine ecosystem. In this respect, costeffective and efficient decontamination techniques need to be developed and verified to remediate the contaminated water. Prussian blue (PB) is known as a representative material that can adsorb Cs by ion-trapping and is widely used for medical purposes. However, there is a limitation that PB itself is non-separable and highly mobile in aqueous system, so it needs a fixture, such as bentonite, to be collected after the adsorption. Furthermore, while the performance of PB toward Cs is relatively well known, its behavior toward Sr has rarely been reported. The object of this study is to investigate the sorption characteristics of Cs and Sr onto PB-functionalized bentonite at various conditions. The adsorbent employed in the present work was prepared by mixing bentonite, FeCl3, and K4[Fe(CN)6] at room temperature for 24 hours in the aqueous solution. The concentrations of FeCl3 and K4[Fe(CN)6] were set to a range of 5-200 % compared to the cation exchange capacity of bentonite. After that, the PB-functionalized bentonite was sieved with a mesh size of 63 μm and then reacted with the Cs and Sr solution at various liquid-to-solid (L/S) ratios of 2-10 g/L for up to 500 minutes. Moreover, synthetic seawater containing additional Cs and Sr was reacted with PBfunctionalized bentonite to characterize the ion selectivity of PB. After the completion of the adsorption experiment, a part of the adsorbent was separated and desorption of Cs and Sr with 2 M of nitric acid was performed. For the quantification of aqueous Cs and Sr concentrations, ICP-MS was employed after the filtration with a pore size of 0.45 μm. The result obtained in this study revealed a high sorption affinity of Cs and Sr onto PBfunctionalized bentonite. The analysis results also presented that the sorption reactions of Cs and Sr reached their steady state within 10 minutes of reaction time. Furthermore, the ion selectivity toward Cs and Sr was verified through sorption test with synthetic seawater. According to the high sorption affinity and selectivity, the PB-functionalized bentonite synthesized through this study is expected to be widely used for remediating the Cs- and Sr-contaminated groundwater and seawater, particularly in nuclear waste-relevant industries.

The radiological characterization of SSCs (Structure, Systems and Components) plays one of the most important role for the decommissioning of KORI Unit-1 during the preparation periods. Generally, a regulatory body and laws relating to the decommissioning focus on the separation and appropriate disposal or storage of radiological waste including ILW (intermediate level waste), LLW (low level waste), VLLW (very low level waste) and CW (clearance waste), aligned with their contamination characteristics. The result of the preliminary radiological characterization of KORI Unit-1 indicated that, apart from neutron activated the RV (reactor vessel), RVI (reactor vessel internals), and BS (biological shielding concrete), the majorities of contamination were sorted to be less than LLW. Radiological contamination can be evaluated into two methods. Due to the difficulties of directly measuring contamination on the interior surfaces of the pipe, called CRUD, the assessment was implemented by modeling method, that is measuring contamination on the exterior surfaces of the pipes and calculating relative factors such as thickness and size. This indirect method may be affected by the surrounding radiation distribution, and only a few gamma nuclides can be measured. Therefore, it has limitation in terms of providing detailed nuclide information. Especially, α and β nuclides can only be estimated roughly by scaling factors, comparing their relative ratios with the existing gamma results. To overcome the limitation of indirect measurement, a destructive sampling method has been employed to assess the contamination of the systems and component. Samples are physically taken some parts of the systems or components and subsequently analyzed in the laboratory to evaluate detailed nuclides and total contamination. For the characterization of KORI Unit-1, we conducted the radiation measurement on the exterior surfaces of components using portable instruments (Eberline E-600 SPA3, Thermo G20-10, Thermo G10, Thermo FH40TG) at BR (boron recycle system) and SP (containment spray system) in primary system. Based on these results, the ProUCL program was employed to determine the destructive sample collection quantities based on statistical approach. The total of 5 and 8 destructive sample quantities were decided by program and successfully collected from the BR and SP systems, respectively. Samples were moved to laboratory and analyzed for the detail nuclide characteristics. The outcomes of this study are expected to serve as valuable information for estimating the types and quantities of radiological waste generated by decommissioning of KORI Unit-1.

The Derived Concentration Guideline Level (DCGL) is required to release the facility from the nuclear safety act at the stage of site restoration of the decommissioning nuclear power plant. In order to evaluate DCGL, there are various requirements, and among them, the selection of input parameters based on the application scenario is the main task. Especially, it is important to select input parameters that reflect site characteristics, and at this time, a single deterministic value or a probabilistic distribution can be applied. If it is inappropriate to apply a particular single value, it may be reasonable to apply various distributions, and the RESRAD code provides for evaluation using probabilistic methods. Therefore, this study aims to analyze the difference between the application of the deterministic method and the application of the probabilistic method to the area and thickness of the contaminated zone among the site characteristics data. This study analyzed the thickness and area of the contaminated zone, and in the case of thickness, the deterministic method was applied by changing the thickness at regular intervals from the minimum depth considered by MARSSIM to the thickness of the unsaturated zone identified in previous research data. In addition, a probabilistic analysis was performed by applying a distribution to the thickness of contaminated zone. Second, for the area of the contaminated zone, the dose was evaluated for each area in consideration of the areas to be considered when deriving Area Factor (AF), and the resulting change in DCGL was observed. As a result, the DCGL tends to decrease as the thickness increases, and it seems to be saturated when the thickness exceeds a certain thickness. Therefore, It was confirmed that the level of saturated values is similar to that of entering a probabilistic distribution, and in the case of a parameter that is reasonable to enter as a distribution rather than as a single value, it is sufficiently conservative to perform a probabilistic evaluation. In the case of area change, the DCGL evaluation result showed that the DCGL increased as the scale decreased. The magnitude of the change varies depending on the characteristics of each radionuclide, and in the case of radionuclides where external exposure gamma rays have a major exposure effect, the change is relatively small. It can be seen that the change in DCGL according to the area has the same tendency as the AF applicable to the survey unit for small survey units applied in the final status survey.

According to acceptance of radioactive waste, homogeneous waste such as concentrated liquid waste and spent resin must be solidified to reduce radiological hazards and protect public health and the ecology. However, when using a High Integrity Containers (HIC), it is stated that homogeneous waste can be disposed of without applying the solidification test requirements. PCHIC, developed in korea, is composed of polyethylene (PE, interior), polymer concrete (PC, filler), and steel (external reinforcement). Currently, PC-HIC will be used as a packaging container for low-level liquid waste and spent resin waste. PE has a lower shielding efficiency compared to PC, but it offers the economic advantage of lower production costs. Therefore, cost savings can be expected if very low-level waste is packaged and disposed of HIC made only of PE materials (PEHIC). Despite the economical advantage of PE-HIC, PE-HIC has not been used domestically since NRC (Nuclear Regulatory Commission) reported that PE-HIC couldn’t meet the mechanical integrity criteria for radiation exsure. However, according to IAEA (International Atomic Energy Agency) research, it has been reported that mechanical integrity of PE-HIC is not affected when the absorbed dose is below 50 kGy. Therefore, in this study, Radiological impact of VLLW packaged into PE-HIC is evaluated to confirm that the absorbed dose is below 50 kGy, which then be used to assess feasibility of PE-HIC to be used as packaging and disposal container for radioactive waste. Radiological impact of VLLW packaged into PE-HIC is evaluated to confirm that the absorbed dose is below 50 kGy, which then be used to assess feasibility of PE-HIC to be used as packaging and disposal container for radioactive waste. The feasibility of using PE-HIC as packaging-disposal containers for radioactive waste will be reviewed. In this study, the radiation effects of only waste packaged in PE-HIC were considered, and additional assumptions are as follows. - Nuclides subject to radioactivity evaluation: Co-60, Cs-137 - Radioactivity concentration: very low-level radioactive wastel concentration limit - Target waste: waste resin - PE-HIC dimensions: outer diameter: 1,194 mm, height: 1,290 mm, and thickness 88 mm (PCHIC internal PE shape) Considering the above assumption, the exposure rate was evaluated using the MicroShield program. Since the density of PE-HIC in the MicroShield program was assumed as the density of air. The absorbed dose was recalculated through density correction of the derived exposure rate. As a result, it was confirmed that absorbed dose was about 2-3 mGy over 300 years. As a result of dose evaluation by MicroShield, it is judged that the mechanical integrity of PEHIC as an packaging of VLLW can be proved by confirming that the absorption dose irradiated to PE-HIC by internal waste is less than 50 kGy.

For the release of the nuclear power plant site after the decommissioning, a reliable exposure dose assessment considering the environmental impact of residual radionuclides is essentially required. In this study, the Derived Concentration Guideline Level (DCGL) for the hypothetically contaminated surface soil at the Wolsong nuclear power plant (NPP) unit 1 site was preliminarily calculated by using the RESRAD-OFFSITE computational code and compared with the other case studies. Moreover, radiation exposure dose for local residents and relevant exposure pathways were quantitatively analyzed based on the calculation model established through this work. For the target site modeling, the source term was determined by referring to the previous case studies regarding the nuclear power plant decommissioning, quantification analysis data of pressure tubes of Wolsong NPP unit 1, and radionuclide data estimated by using the MCNP/ORIGEN-2 code. In total, 14 different radioisotopes such as Ag-108m, C-14, Co-60, Cs-134/137, Fe-55, H-3, Nb-93m/94, Ni-63, Sb-125, Sn-121m, Sr-90, and Zr-93 were considered as target radionuclides. In addition, the geological structure model of the Wolsong NPP site was established based on the final safety analysis report of Wolsong NPP unit 1. The distribution coefficients (Kd) were taken from the JAEA-SDB to estimate the migration/retardation behavior of various radionuclides under the groundwater condition of the Wolsong NPP site. In the present work, the DCGL values were calculated according to the site release criterion of 0.1 mSv/yr, which indicates the radiation protection standard for the site release. Moreover, the exposure pathway and sensitivity analyses were conducted to assess the sensitive input parameters remarkably influencing the calculation result. For the evaluation of exposure dose for local residents, a site layout centered around Wolsong NPP unit 4, located in the closest proximity to the residents’ habitation area, was alternatively established and all potential exposure pathways were considered as a comprehensive resident farmer scenario. The results obtained from this study are expected to serve as a preliminary case study for the DCGL values regarding the surface soil at the Wolsong NPP unit 1 site and for evaluating the radiation exposure dose to local residents resulting from the residual radioactivity at the site after the decommissioning.

Wide-area surface decontamination is essential during the sudden release of radioisotopes to the public, such as nuclear accidents or terrorist attacks. A spray coating composed of a reversible complex between poly (vinyl alcohol) (PVA) and phenylboronic acid-grafted poly (methyl vinyl ether-alt-mono-sodium maleate) (PBA–g–PMVE–SM) was developed to remove radioactive cesium from surfaces. The simultaneous spay of PVA and PBA–g–PMVE–SM aqueous polymer solutions containing Cs adsorbent to contaminated surfaces resulted in the spontaneous formation of a PBA–diol ester bond-based gel-like coating. The Cs adsorbent suspended in the gel-like coating selectively removed Cs-137 from the Cs-contaminated surface. The used gel-like coating were removed from surfaces by simple water rinsing. This recovery way has advantages compared with costly incineration to remove the organic materials for final disposal/storage of the radioactive waste. Thus, our spray coating is suitable for practical wide-area surface decontamination. In radioactive tests, the hydrogel containing Cs-adsorbent showed substantial Cs-137 removal efficiencies of 96.996% for painted cement and 63.404% for cement, which are 2.33 times better than the values for the commercial surface decontamination coating agent DeconGel.

A Partially hydrolyzed poly (vinyl acetate) (PHPVA)-borax complex-based gel-like coating was successfully developed for the decontamination of Simulated nuclear fallout (SFO) from surfaces. The sprayable coating was self-generated on the surface by borate-diol ester bonds after simultaneously mixing two solutions of borax and PHPVA. The SFO particles, synthesized at 1,200°C for melting, were glassy while some crystalline phases (e.g., SiO2 and Fe2O3) existed together. The SFO particles were fixed onto the Stainless steel (SS) substrate by dropping and evaporating water. for examination of the dust-removal performance of PHPVA-borax based coating. The dusts on the SS surface was successfully removed by casting the PHPVA-borax based coating within 1 minute, demonstrating the excellent dust-removal property of the PHPVA-borax based coating. The used PAB complex in wet state was recovered by using vacuum suction machine in short time. The solid-state PHPVA-borax based film was self-delaminated from the SS substrate after fully drying the used PHPVA-borax coating but this requires long period of time.

Economical radioactive soil treatment technology is essential to safely and efficiently treat of high-concentration radioactive areas and contaminated sites during operation of nuclear power plants at home and abroad. This study is to determine the performance of BERAD (Beautiful Environmental construction’s RAdioactive soil Decontamination system) before applying magnetic nanoparticles and adsorbents developed by the KAERI (Korea Atomic Energy Research Institute) which will be used in the national funded project to a large-capacity radioactive soil decontamination system. BERAD uses Soil Washing Process by US EPA (402-R-007-004 (2007)) and can decontaminate 0.5 tons of radioactive soil per hour through water washing and/or chemical washing with particle size separation. When contaminated soil is input to BERAD, the soil is selected and washed, and after going through a rinse stage and particle size separation stage, it discharges decontaminated soil separated by sludge of less than 0.075 mm. In this experiment, the concentrations of four general isotopes (A, B, C, and D which are important radioisotopes when soil is contaminated by them.) were analyzed by using ICP-MS to compare before and after decontamination by BERAD. Since BERAD is the commercial-scale pilot system that decontaminates relatively large amount of soil, so it is difficult to test using radioactive isotopes. So important general elements such as A, B, C, and D in soil were analyzed. In the study, BERAD decontaminated soil by using water washing. And the particle size of soil was divided into a total of six particle size sections with five sieves: 4 mm, 2 mm, 0.850 mm, 0.212 mm, and 0.075 mm. Concentrations of A, B, C, and D in the soil particles larger than 4 mm are almost the lowest regardless of before and after decontamination by BERAD. For soil particles less than 4 mm, the concentrations of C and D decreased constantly after BERAD decontamination. On the other hand, the decontamination efficiency of A and B decreased as the soil particle became smaller, but the concentrations of A and B increased for the soil particle below 0.075 mm. As a result, decontamination efficiency of one cycle using BERAD for all nuclides in soil particles between 4 mm and 0.075 mm is about 45% to 65 %.

Nuclear facilities present the important task related to the migration and retention of radioactive contaminants such as cesium (Cs), strontium (Sr), and cobalt (Co) for unexpected events in various environmental conditions. The distribution coefficient (Kd) is important factor for understanding these contaminants mobility, influenced by environmental variables. This study focusses the prediction of Kd values for radionuclides within solid phase groups through the application of machine-learning models trained on experimental data and open source data from Japan atomic energy agency. Three machine-learning models, such as the convolutional neural network, artificial neural network, and random forest, were trained for prediction model of the distribution coefficient (Kd). Fourteen input variables drawn from the database and experimental data, including parameters such as initial concentration, solid-phase characteristics, and solution conditions, served as the basis for model training. To enhance model performance, these variables underwent preprocessing steps involving normalization and log transformation. The performances of the models were evaluated using the coefficient of determination. These results showed that the environmental media, initial radionuclide concentration, solid phase properties, and solution conditions were significant variables for Kd prediction. These models accurately predict Kd values for different environmental conditions and can assess the environmental risk by analyzing the behavior of radionuclides in solid phase groups. The results of this study can improve safety analyses and longterm risk assessments related to waste disposal and prevent potential hazards and sources of contamination in the surrounding environment.

The decommissioning of domestic Nuclear Power Plants (NPPs) in Korea is expected to begin with the Kori-1, which was permanently shutdown in 2017. In addition, Wolsong-1 has been also permanently shutdown, and another type will be the decommissioning project following Kori-1. KHNP is promoting operation and decommissioning projects as the owner of NPPs, and the Central Research Institute (CRI) has been developing a Final Decommissioning Plan (FDP) for the decommissioning license document. The FDP consists of 11 major chapters in the order of overview of the project, characteristic evaluation, safety assessment, radiation protection, decontamination & dismantlement activities, waste management, etc. The contents described in each chapter are individual chapters, but there are also parts that consider the connection with other chapters. The CRI, which develops the FDP for the first decommissioning project in Korea, has spent a lot of time and effort considering this and has been proceeding through trial and error until the present stage. Therefore, this study aims to explain the current status of FDP, a license document for domestic decommissioning projects, and the link between major input data in major chapters. It can be said that System, Structure, and Components (SSCs) subject to dismantling are considered as the scope of FDP. Chapters that perform estimations on these dismantling targets may include safety assessments, exposure dose assessments for workers and residents, and waste inventory assessments. Therefore, an important part of performing the estimation works is to consider the entire scope of decommissioning activities, and as a way, it can start from data based on the inventory data. After generating the inventory data, the waste treatment classification for the inventory is designated by reflecting the results of the characterization. In addition, for cost estimation, the cost of decommissioning project is predicted by inputting some data (i.e., UCF) such as work process, number of workers, and time required for each item with data reflected in quantity and characterization. After that, based on these inventory, characterization, and UCF data, accident scenarios and industrial safety evaluation are performed for the safety assessment. The worker exposure dose is estimated by considering the dose rate of the workspace with these data. In the case of the amount of waste, the final amount of waste is estimated by considering the factors of reduction and decontamination. In summary, the main estimation contents of FDP are evaluated by adding elements required for the purpose of each chapter from data combined with inventory, characterization, and UCF, so the contents of these chapters are based on the logic of considering the entire scope of decommissioning in common.

KORAD (Korea Radioactive Waste Agency, http://www.korad.or.kr) has stored slightly contaminated ascon (asphalt coated concrete mixture) that was introduced to Gyeongju repository about a decade ago waiting for a final disposal. It is believed to be mainly contaminated by radioisotope 137Cs due to impurities introduced from the outside during the ascon manufacturing process. We studied characteristics of the radioactive waste to see whether this material would be proper enough to be disposed in Gyeongju LILW repository or be other ways to reduce the disposal volume including self-disposal before its final disposal otherwise. KORAD looked into the properness of characteristics of ascon in terms of WAC (Waste Acceptance Criteria) documented by KORAD that includes general chemical and physical properties of asphalt, density, size of grains, content of organic material and possibility of existence of chelate materials that qualitatively limited to be disposed by the criteria. And other associated characteristics such as gas generation and bio degradation were also investigated. Based on the data obtained from the study, we proposed various plausible solutions in associated with operational and disposal safety and economic view points. This study will be used for KORAD’s decision on how to control and safely dispose the spent ascon within a reasonable time period. And also those experiences may be applied for other LILW issues that require treatment or conditioning of radioactive wastes in the future.

Radioactive waste (hereinafter referred to as mixed waste) containing hazardous substances (heavy metals, organic and inorganic waste liquids, asbestos, etc.) has been continuously generated from domestic nuclear power plants, nuclear facilities, and other industrial facilities, and heavy metals were released during the dismantlement of Kori Unit 1 and Wolseong Unit 1. Lead, cadmium, mercury, arsenic), asbestos, decontamination waste liquid (organic/inorganic waste liquid), etc. may be generated. Although hazardous waste related to the nuclear industry continues to be generated, only the regulation direction for hazardous substances is presented in the provisions related to hazardous substances in the delivery regulations for low and intermediate-level radioactive waste and the acceptance criteria for low and intermediate-level radioactive waste disposal facilities. In particular, because there is no clear definition of “hazardousness” and specific standards such as concentration and characteristics for classification of hazardous substances, as well as hazard removal procedures when the hazardousness of radioactive waste is confirmed, no hazardous substances have been delivered in Korea to date and many mixed wastes are stored at each generation facility or at the NPP. As a plan to improve delivery standards related to mixed waste is being prepared recently, it is believed that if the acceptance standards are revised accordingly, it will be possible to confirm the suitability for disposal of drums produced after the establishment of the acceptance standards in 2015. However, it is believed that securing disposal suitability for waste that was packed in 200L drums and compressed under super high pressure in the absence of specific technical standards and regulatory guidelines for the disposal of radioactive waste containing hazardous substances would still remain a difficult problem. In this report overseas acceptance standards related to hazardous waste were reviewed and a plan to secure the disposal suitability of 200 L drums compressed with of super high pressure was proposed.