정온한 생활환경의 보전과 국민 건강의 보호를 위해 소음에 대한 환경기준을 환경정책기본법에 따라 일반지역과 도로변지역으로 구 분하여 관리하고 있다. 그 중 도로변지역에 있는 주거지역은 주간시간대 65 dBA, 야간시간대 55 dB 이하로 환경소음을 관리하여야 한 다. 그러나, 심화된 도시화에 따라 주거건축물의 밀도는 보다 높아지고, 도심 내 간선도로의 고속화로 주거지역에 대한 도로소음의 영 향이 증가되어가고 있다. 소음진동관리법에서는 방음시설의 설치 등의 조치를 의무화하고 있으며, 이에 따라 방음벽, 방음터널 등 다 양한 방음시설이 소음저감 대책으로서 현장의 여건에 따라 사용되고 있다. 최근, 배수성 아스팔트 포장이 노면에서의 흡음에 따른 타 이어-노면 간의 마찰소음 저감 효과를 바탕으로 손쉽게 적용할 수 있는 방음대책의 하나로 활용되고 있다. 하지만, 저소음 아스팔트 포장이 일반 아스팔트 포장에 비해 환경소음을 저감시킬 수 있는지 정량적으로 평가하는 것이 매우 어려운 상황이다. 최근 타이어-노 면 간의 마찰소음을 정량적으로 평가할 수 있는 CPX 측정방법이 KS I ISO 11819-2로 표준화되어 국토부의 ‘배수성 아스팔트 콘크리 트 포장 생산 및 시공지침’ 중 소음 측정방법에도 인용되어 있다. 하지만, CPX 방법은 정속 주행시 환경의 영향을 통제한 상태에서 근접 소음만을 측정하기 때문에, 포장 종류나 경년변화에 따른 상대적인 차이를 정량화하는 것은 유리하지만, 환경기준에 따른 소음저 감도를 직접적으로 비교할 수 없는 단점이 있다. 이에 따라, 본 연구에서는 CPX 측정방법으로 도출한 포장구간별 소음저감량과 환경 소음 평가의 기준이 되는 갓길에서 측정한 등가소음간의 상관관계 분석을 통해, 환경소음 관리 및 도로소음 평가를 위한 CPX 측정결 과의 활용방안에 대해 고찰하였다.

도로 위로 차량이 통과할 때 발생하는 타이어-노면 소음을 평가하기 위한 ISO 국제표준이 제정되어 있다. 갓길에서 통과소음을 측정 하고 차량속도와 소음 정보를 이용하여 통계 분석 방법으로 기준속도에서의 소음을 추정하는 SPB (Statistical Pass-by) 방법과 시험 타 이어를 이용하여 노면과 타이어 사이의 발생소음을 근접하여 측정하는 CPX (Close Proximity) 방법이 있다. 두 표준에서 제시하고 있 는 동일한 기준속도와 온도 조건에 대해서 국내 환경에 맞게 합리적으로 적용할 수 있는 방안을 검토하였다. 50 km/h, 80 km/h, 110 km/h 이외의 기준속도로 측정하는 것에 대한 적합성을 확인하기 위해, 80 km/h, 100 km/h, 120 km/h로 동일 현장에서 측정한 결과를 분석하여 속도와 소음과의 상관성을 분석하였다. 이를 통해 표준에서 제시한 속도 이외의 속도도 기준속도로 활용하여 측정이 가능한 것을 확인하였다. 또한, 표준에서 제시하고 있는 5℃ ~ 30℃ 온도 범위를 검토하여 국내 환경조건에 따른 측정 불가능한 일수를 최소 화 하고자 하였다. 고온에서 아스팔트 블리딩으로 인한 스틱 스냅 소음의 발생을 우려하여 측정 가능 온도 상한치를 두었으나, 국내 고속도로에 사용하고 있는 아스팔트 공용성 등급 등을 고려하였을 때, 보다 높은 온도에서의 측정도 가능할 것으로 판단된다. 다만, 실제 측정 데이터가 부족하여, 충분한 데이터 수집 및 분석을 통하여 온도 관련 제한 조건을 완화하여 측정할 수 있을 것으로 사료된 다.

We evaluate the properties of friction welded STK400 steel tube in terms of the relationship between microstructures and mechanical properties. Friction welding is conducted at a rotation speed of 1,600 rpm and upset time of 3-7 sec for different thicknesses of STK 400 tubes. To analyse the grain boundary characteristic distributions(GBCDs) in the welded zone, electron backscattering diffraction(EBSD) method is introduced. The results show that a decrease in welding time (3 sec.) creates a notable increase grain refinement so that the average grain size decreases from 15.1 μm in the base material to 4.5 μm in the welded zone. These refined grains achieve significantly enhanced microhardness and a slightly higher yield and higher tensile strengths than those of the base material. In particular, all the tensile tested specimens experience a fracture aspect at the base material zone but not at the welded zone, which means a soundly welded state for all conditions

This study was carried out to evaluate the developed microstructures and mechanical properties of friction welded A6063 alloy. For this work, specimens were prepared at a size of 12 mm Ø × 80 mm, and friction welding was carried out at a rotation speed of 2,000 RPM, friction pressure of 12 kgf/cm² and upset pressure of 25 kgf/cm². To perform an analysis of the grain boundary characteristic distributions, such as the grain size, orientation and misorientation angle distributions, the electron back-scattering diffraction method was used. In addition, in order to identify the dispersed intermetallic compounds of the base and welded materials, transmission electron microscopy was used. The experimental results found that the application of friction welding on A6063 led to significant grain refinement of the welded zone relative to that of the base material. Besides this, intermetallic compounds such as AlMnSi and Al2Cu were found to be dispersed with more refined size relative to that of the base material. This formation retains the mechanical properties of the welds, which results in the fracture aspect at the base material zone. Therefore, based on the developed microstructures and mechanical properties, the application of friction welding on A6063 could be used to obtain a sound weld zone.

To investigate the oviposition preference and development of azuki bean weevil (Callosobruchus chinensis L.), the following six different leguminous seeds were used in this study: red bean (Vigna angularis (Willd.) Ohwi & Ohashi), black soybean (Glycine max (L.) Merr.), soybean (Glycine max (L.) Merr.), seoritae (Glycine max (L.) Merr.), small black bean (Rhynchosia nulubilis) and kidney bean (Phaseolus vulgaris var. humilis Alef.). In the study of oviposition preference, the numbers of eggs per leguminous seed on red bean, black soybean, soybean, seoritae and small black bean were 1.23, 0.61, 0.69, 1.05 and 1.13, respectively. The maximum daily number of eggs was observed at 48 hours and the minimum was at 96 hours. According to each host leguminous seed, developmental time for each host seed was different. The shortest adult emergence time was on red bean (25.27 days). The other five leguminous seeds increased or doubled the adult emergence time. Adult emergence rates feeding on red bean, seoritae, black soybean, soybean, small black bean were 83.33%, 28.23%, 27.87%, 20.44%, and 11.59%, respectively. Emergence rate on red bean was four times higher than the rate on other seeds. The longevity of emerged female adults was almost all longer than that of males. The male adults weighed the lowest of feeding on small black bean. Female adults weighed the lowest of feeding on soybean. Adult weights were the heaviest for both males and females feeding on red bean. As a result, hosts of azuki bean weevil could decrease oviposition rate, emergence rate, adult longevity, and adult weight but increase emergence time. Especially in kidney bean, adult was not completely emerged. No eggs were laid. These results suggest that there might be emergence inhibitors in kidney bean. These imformation might be used to control damages caused by azuki bean weevils.

We evaluated the developed microstructures and mechanical properties of a severely plastically deformed Ni-30Cr alloy. Normal rolling and differential speed rolling were used as deformation processes, and the thicknesses of the specimens were reduced to 68 % of the original thickness after holding at 700 oC for 10 min and annealing at 700 oC for 40 min to obtain a fully recrystallized microstructure. Electron backscattering diffraction was used to analyze the characteristic distribution of the grain boundaries on the deformed and annealed specimens. Differential speed rolling was more effective for refining grains in comparison with normal rolling. The grain size was refined from 33 mm in the initial material to 8.1 mm with normal rolling and 5.5 mm with differential speed rolling. The more refined grain in the differential-speed-rolled material directly resulted in increases in the yield and tensile strengths by 68 % and 9.0%, respectively, compared to normal rolling. We systematically explain the relationship between the grain refinement and mechanical properties through a plastically deformed Ni-30Cr alloy based on the development of a deformation texture. The results of our study show that the DSR process is very effective when used to enhance the mechanical properties of a material through grain refinement.

본 연구는 국내 멸종위기식물인 개가시나무의 분포 범위와 국내 자생지 내에서의 생육 특성을 파악하고자 실시하였다. 개가시나무는 참나무과에 속하는 상록활엽 교목으로서 일본, 대만, 중국, 한국 등의 따뜻한 지방에 자라는 난대성 수종이다. 국내에서는 제주도의 해발 80~350 m 내에 분포하였으며, 대부분 제주도 서남부지역의 해발 100~200m에 집중 분포하였다. 개가시나무의 수고는 평균 9.8±1.9 m로 9~12 m 사이의 개체가 가장 많았으며, 흉고직경은 평균 22.6±6.8㎝로 20~30㎝의 개체가 가장 많았다. 또한 맹아지의 발생으로 다수의 분지가 형성 되었으며, 평균 3.8±2.1개의 맹아로 이루어졌다. 자생지 내에 분포하는 개가시나무의 96.2%에 덩굴식물이 부착되어있으며, 덩굴식물은 15과 18종으로 상록성 덩굴식물인 마삭줄의 비율이 가장 높았다. 덩굴식물이 개가시나무의 수관 형성에 미치는 영향의 정도를 분석한 결과, 9~12 m의 개가시나무에서 수관형성에 영향을 주어 고사된 가지가 확인된 개체가 가장 많았으며, 부착된 덩굴식물의 종 수가 많을수록 높은 영향을 주는 것으로 판단되었다. 따라서 자생지 내에서 개가시나무의 보존을 위해서는 이들 덩굴식물의 생육에 대한 지속적인 모니터링과 관리가 이루어져야 할 것이다.

To evaluate the development of the microstructure and mechanical properties on surface modified and post-heat-treated Inconel 718 alloy, this study was carried out. A friction stir process as a surface modification method was employed,and overlap welded Inconel 718 alloy as an experimental material was selected. The friction stir process was carried out ata tool rotation speed of 200 rpm and tool down force of 19.6-39.2kN; post-heat-treatment with two steps was carried out at720oC for 8h and 620oC for 6h in vacuum. To prevent the surface oxidation of the specimen, the method of using argongas as shielding was utilized during the friction stir process. As a result, applying the friction stir process was effective todevelop the grain refinement accompanied by dynamic recrystallization, which resulted in enhanced mechanical properties ascompared to the overlap welded material. Furthermore, the post-heat-treatment after the friction stir process accelerated theformation of precipitates, such as gamma prime (γ') and MC carbides, which led to the significant improvement of mechanicalproperties. Consequently, the microhardness, yield, and tensile strengths of the post-heat-treated material were increased morethan 110%, 124% and 85%, respectively, relative to the overlap welded material. This study systematically examined therelationship between precipitates and mechanical properties.

This study evaluated the enhancement of microstructural and mechanical properties of a cross rolled Ni-10Cr alloy, comparing with conventionally rolled material. Cold rolling was carried out to 90% thickness reduction and the specimens were subsequently annealed at 700˚C for 30 min to obtain a fully recrystallized microstructure. Cross roll rolling was carried out at a tilted roll mill condition of 5˚ from the transverse direction in the RD-TD plane. In order to observe the deformed microstructures of the cold rolled materials, transmission electron microscopy was employed. For annealed materials after rolling, in order to investigate the grain boundary characteristic distributions, an electron back-scattering diffraction technique was applied. Application of cold rolling to the Ni-10Cr alloy contributed to notable grain refinement, and consequently the average grain size was refined from 135 μm in the initial material to 9.4 and 4.2 μm in conventionally rolled and cross rolled materials, respectively, thus showing more significantly refined grains in the cross rolled material. This refined grain size led to enhanced mechanical properties such as yield and tensile strengths, with slightly higher values in the cross rolled material. Furthermore, the<111>//ND texture in the CRR material was better developed compared to that of the CR material, which contributed to enhanced mechanical properties and formability.

The microstructures and mechanical properties of friction stir welded lap joints of Inconel 600 and SS 400 were evaluated; friction stir welding was carried out at a tool rotation speed of 200 rpm and welding speed of 100 mm/min. Electron back-scattering diffraction and transmission electron microscopy were introduced to analyze the grain boundary characteristics and the precipitates, respectively. Application of friction stir welding was notably effective at reducing the grain size of the stir zone. As a result, the reduced average grain size of Inconel 600 ranged from 20μm in the base material to 8.5μm in the stir zone. The joint interface between Inconel 600 and SS 400 showed a sound weld without voids and cracks, and MC carbides with a size of around 50 nm were partially formed at the Inconel 600 area of lap joint interface. However, the intermetallic compounds that lead to mechanical property degradation of the welds were not formed at the joint interface. Also, a hook, along the Inconel 600 alloy from SS 400, was formed at the advancing side, which directly brought about an increase in the peel strength. In this study, we systematically discussed the evolution of microstructures and mechanical properties of the friction stir lap joint between Inconel 600 and SS 400.

We carried out this study to evaluate the grain refining in and the mechanical properties of alloys that undergo severe plastic deformation (SPD). Conventional rolling (CR) and cross-roll rolling (CRR) as SPD methods were used with Ni-20Cr alloy as the experimental material. The materials were cold rolled to a thickness reduction of 90% and subsequently annealed at 700˚C for 30 min to obtain a fully recrystallized microstructure. For the annealed materials after the cold rolling, electron back-scattered diffraction (EBSD) analysis was carried out to investigate the grain boundary characteristic distributions (GBCDs). The CRR process was more effective when used to develop the grain refinement relative to the CR process; as a result, the grain size was refined from 70μm in the initial material to 4.2μm (CR) and 2.4μm (CRR). These grain refinements have a direct effect on improving the mechanical properties; in this case, the microhardness, yield and tensile strength showed significant increases compared to the initial material. In particular, the CRR-processed material showed more effective values relative to the CR-processed materials. The different texture distributions in the CR (001//ND) and CRR (111//ND) were likely the cause of the increase in the mechanical properties. These findings suggest that CRR can result in materials with a smaller grain size, improved texture development and improved mechanical properties after recrystallization by a subsequent annealing process.

This study was carried out to evaluate the microstructures and mechanical properties of a friction stir welded Ni based alloy. Inconel 600 (single phase type) alloy was selected as an experimental material. For this material, friction stir welding (FSW) was performed at a constant tool rotation speed of 400 rpm and a welding speed of 150~200 mm/min by a FSW machine, and argon shielding gas was utilized to prevent surface oxidation of the weld material. At all conditions, sound friction stir welds without any weld defects were obtained. The electron back-scattered diffraction (EBSD) method was used to analyze the grain boundary character distributions (GBCDs) of the welds. As a result, dynamic recrystallization was observed at all conditions. In addition, grain refinement was achieved in the stir zone, gradually accelerating from 19 μm in average grain size of the base material to 5.5 μm (150 mm/min) and 4.1 μm (200 mm/min) in the stir zone with increasing welding speed. Grain refinement also led to enhancement of the mechanical properties: the 200 mm/min friction stir welded zone showed 25% higher microhardness and 15% higher tensile strength relative to the base material.

The present study was carried out to evaluate the microstructural and mechanical properties of cross-roll rolled pure copper sheets, and the results were compared with those obtained for conventionally rolled sheets. For this work, pure copper (99.99 mass%) sheets with thickness of 5 mm were prepared as the starting material. The sheets were cold rolled to 90% thickness reduction and subsequently annealed at 400˚C for 30 min. Also, to analyze the grain boundary character distributions (GBCDs) on the materials, the electron back-scattered diffraction (EBSD) technique was introduced. The resulting cold-rolled and annealed sheets had considerably finer grains than the initial sheets with an average size of 100 μM. In particular, the average grain size became smaller by cross-roll rolling (6.5 μM) than by conventional rolling (9.8 μM). These grain refinements directly led to enhanced mechanical properties such as Vickers micro-hardness and tensile strength, and thus the values showed greater increases upon cross-roll rolling process than after conventional rolling. Furthermore, the texture development of<112>//ND in the cross-roll rolling processed material provided greater enhancement of mechanical properties relative to the case of the conventional rolling processed material. In the present study, we systematically discuss the enhancement of mechanical properties in terms of grain refinement and texture distribution developed by the different rolling processes.

교통량이 많은 도심지내 장대 지하차도 건설은 교통정체 해소에 기여를 하지만 초기 공사비가 많이 소요되는 단점이 있다. 또한, 화재등 유고시 이용자의 안전을 최우선으로 고려되어야 한다. 즉, 장대 지하차도 건설에 있어서 경제성과 안전성이 함께 만족할 수 있는 건설 방안이 필요하다. 세종지하차도는 이러한 문제점을 극복하고자 다음과 같이 지하차도의 환기방식 및 단면, 포장형식, 사고 예방 및 발생시를 대비한 종합방재시스템을 구축하였다. ·환기방식은 종류식 환기방식의 경제성과 횡류식 환기방식의 제연성능을 겸비할 수 있는 조합형 환기방식과 Duct Arch 단면을 적용하여 공사비 절감 및 운영시 유지관리비를 획기적으로 절감하였다. ·지하차도 포장형식은 화재시 내화성이 우수하며 유독가스 발생이 없는 HPC(고성능 콘크리트 포장) 포장을 적용하여 이용자의 안전을 최우선으로 고려하였고 일반 아스팔트 포장 및 배수성 아스팔트 포장에 비해 우수한 성능과 공용수명을 가진 공법을 적용함으로서 유지보수비용의 절감을 가능하게 하였다. 또한, 콘크리트포장의 단점인 소음발생을 최소화하기 위해 타이닝과 그루빙을 적용하였다. ·지하차도내 화재 등 유고시 신속한 대피가 가능하도록 피난 연락문 간격을 167m 간격으로 설치하고 비상탈출계단 6개소를 확보하였다. 또한 노약자 및 환자의 지하차도 외부로 대피를 돕기 위해 비상엘리베이터 3개소를 설치하는 등 사고발생 시 종합적으로 대처할 수 있는 시스템을 마련하여 적용하였다.

수산화물법에 의해 제작된 α-stannic acid의 열분해 거동과 SnO2분말의 성질에 미치는 잔류염소이온의 영향을 관찰하였다. SnCl4와 NH4OH 수용액을 중화시켜 α-stannic acid침전물을 제작하고 NH4NO3수용액으로 세척하였다. 분말내의 잔류 염소이온의 양을 주절하기 위하여 세척정도를 3단계로 조정하였다. 세척후 100˚C에서 건조하고, 500˚C ~ 1100˚C에서 하소함으로써 SnO2분말을 제조하였다. α-stannic acid의열분해 거동ㅇ르 DT-TGA 와 FTIR을 통하여 관찰하고, SnO2분말의 조성과 입자크기 및 비표면적을 각각 AES, TEM 및 BET을 통하여 측정하였다. 잔류 염소이온 양이 감소되면, 저온 하소시 일차입자의 상대적 크기가 커지는 반면 고온하소시에는 상대적으로 감소되었ㄷ. 잔류 염소이온의 일부는 α-stannic acid내의 격자산소 자리에 위치함으로써, 저온가열시 결정수탈리와 결정화를 지연시키고 또한 고온가열시에는 이의 증발에 의해 산소공공이 생성되어 소결을 촉진시킨다고 제의하였다.

Hydroxide법으로 α-주산산(stannic acid)을 만든후, 하고온도를 500˚C~1100˚C로 조정하여 일차입자(Crystallite)크기가 8-54nm인 SnO2 분말을 제작하였다. 분말의 입자(drystalite)클기에 따른 분말특성와 H2, CO가스(0.5v/o)에 대한 감응성 미치공기중에서의 저상변화특성에 미치는 영향을 조사하였다. 입자크기가 감소함에 따라, 분말의 FTIR 흡습특성은 증가하였으나, 격자상수는 일정하였다. 후막소자에서, H2가스에 대해 최대감도를 나타내는 온도와 공기중에서 최소저항을 나타내는 온도는 입자크기가 미세해짐에 따라 점차 낮아졌다. 최소저항점과 최대감도점의 온도저하를 산소흡착종의 활성화에너지의 감소라고 유추하였고, 이러한 에너지의 감소가 미세입자에 의한 감도향상요인 중의 한가지라고 제의하였다.

This study was conducted to monitor the growth and development of Abies koreana seedlings in the Hallasan Mountain. Accordingly, the obtained results indicate that the number of A. koreana seedlings increased by 2.6 and 4.8 times in the Yeongsil and Jindallaebat areas, respectively, over the 10-year period. Most of these seedlings were found to be growing on moss-covered rocks. The average tree height over the last 10 years was obtained as 20.4 cm in the Yeongsil area and 3.6 cm in Jindallaebat with growths of 4.1 cm and 1.4 cm, respectively over the last 2 years. Of all the mature trees that were surviving in 2009, 6 died in Yeongsil in 2014 (with an additional 4 in 2018) and 13 in Jindallaebat in 2016. Over the 10-year period, the diameter at breast height of the trees in Yeongsil and Jindallaebat has increased by an average of 0.6 cm and 4.2 cm. Similarly, an average of 6.8 cones was found in the Yeongsil area in 2014 and 26.3 in Jindallaebat in 2016. However, in 2018, no additional cones were found in the former, although an average of 1.4 cones was observed in the latter. With respect to the average temperature and relative humidity, no significant difference could be observed between two monitored areas from 2016 to 2018. However, in July 2017 and February 2018, the average temperature was higher in the Jindallaebat area, while relative humidity was higher in Yeongsil, there by possibly affecting cone growth and flowering between areas. These results indicate the survival and growth of A. koreana seedlings in the Hallasan Mountain is sensitive to the environments of each area. Hence, continuous monitoring of the environment changes and in-depth studies on the flowering and fruiting of A. koreana seedlings needs to be carried out in order to analyze the relationship between their survival rates and changes in weather conditions.

Birds play a main role in the formation and change of forest structures as they are seed-dispersal agents. This study aims to identify birds consuming fruits and seeds of the tree and their associated fruits and seeds on Jeju Island in the context on the forest restoration in Korea. We conducted field surveys twice a month from 2013 to 2015 at nine study sites located across Jeju Island and collected available photographic and observation records. A total of 50 species of birds consuming fruits and seeds of the tree were identified and birds belonging to Bombycillidae, Pycnonotidae, Zosteropidae, Sturnidae and Fringillidae were confirmed as major birds consuming fruits and seeds of the tree. Gulping was the dominant type of feeding as well as crushing, but relationship between the size of a bird and the number of fruit and seed species used by the bird was not significant. We also documented that 118 fruit and seed species were consumed by birds and that shrubby fruits and seeds were more consumed by birds than those of other plant types. The relative consumption rate of fruits and seeds ranged from 0.02 to 0.44, but five species were the most important fruits and seeds for birds. Our finding suggest that avian frugivorous gulpers will benefit the seed dispersal, especially of five fruiting plants, providing useful baseline data for forest restoration and urban park design.

This study’s purpose was to provide basic data for the monitoring of ecological changes caused by change of vegetation structure of Abies koreana forest in a study site susceptible to climatic change in Yeongsil area of Hallasan Mountain, Jeju Island. Surveys revealed this: in Yeongsil area of Hallasan Mountain, per 1 ha of A. koreana forests, total number 1,781, and A. koreana number 989, accounting for 55.5% of the total number of trees. 190 A. koreana or 19.2% were found to be dead. For the number of individual trees by DBH, trees standing 5 ㎝ -10 ㎝ tall formed the largest portion at 39.9%, and in the case of other trees except A. koreana, the number of individual trees below 5 ㎝ accounted for 23.5% of the total number of trees. The survey of importance by height revealed this: at the top level, the importance of A. koreana was the highest at 106.23, but the sum of importance of temperate deciduous broad-leaved trees (Prunus maximowiczii, Quercus mongolica, and Taxus cuspidata) was higher at 142.84 than that of A. koreana. The analysis of species diversity revealed 0.645 species diversity for the tree layer and 0.817 for the shrub layer; for evenness, 0.549 for the tree layer and 0.664 for the shrub layer; for dominance value; 0.451 for the tree layer and 0.336 for the shrub layer. The analysis of tree vitality revealed that for the A. koreana forests in Yeongsil, the composition ratio of A. koreana by type is AS type>AL type>DS type >DB type, and that of the other trees is AL type>AS type>AF type>AB type. Compared with the forests in other areas, the A. koreana forests in the Yeongsil area have a very high occurrence rate of dead trees, and a high importance of trees is shown in the deciduous broad-leaved tree forests. Compared with the A. koreana forests in the Jindallaebat area, with the same level above sea, the vegetation structures are fast changing. Also, due to dryness and other non-physical environmental changes caused by a lack of rainwater and dry winds in winter, dead trees are fast increasing in number. Environmental changes such as climate change diversely affect the maintenance of A. koreana in individual areas, and if environmental changes are fast and continue long, of the A. koreana forest areas in the Hallasan Mountain, the A. koreana forests in the Yeongsil area will decrease fastest in number and will experience changes in the vegetation structure. Thus, it is necessary to survey the vegetation changes in A. koreana forests, which are distributed in all directions but are centered on Hallasan Mountain, and to thus conduct long-term monitoring and research.