국가 온실가스 인벤토리를 Tier 2 이상의 수준으로 향상시키기 위해서는 IPCC 기본값 대신 국가 고유의 배출계수가 개발 및 이용되어야 한다. 국가 고유 배출계수는 에너지원 종류, 에너지 공정, 시간 추세에 따라 달라지기 때문에, 각 에너지원별 특성값을 파악하는 것은 정확한 인벤토리 구축에 중요한 부분을 차지한다. 국내 석유계 에너지원의 물성은 시간의 경과에 따라 큰 변화는 없었으며, 국내에서 고시되고 있는 에너지원별 열량환산기준 상의 석유계 에너지원에 대한 열량 및 탄소배출계수를 2013년과 2016년에 실제 시료를 수집하여 발열량, 탄소함량 및 탄소배출계수를 산정한 결과값과의 비교분석에서는 대체적으로 일정한 값을 유지하고 있는 것으로 나타났다. 또한, 석유계 에너지원별로 산출된 순발열량과 탄소배 출계수는 2006 IPCC Guideline에 나타낸 값들과 비교하였으며, 대부분의 에너지원이 2006 IPCC G/L의 기본값 및 상한, 하한 범위내의 값을 나타내었다.

대부분의 온실가스는 에너지의 생성 및 이용으로부터 발생되고, 교통부문에서 배출되는 온실가스 중 약 95 % 이상이 수송용 연료에서 기인한다. 또한, IPCC 가이드라인에서 제시하는 배출계수를 사용하였을 경우 국가 고유의 연료특성이 반영되지 않는 단점이 있고, 기후변화협약 교토의정서에 따른 의무 감축국도 UN에 제출하는 국가 온실가스 배출량 보고서 작성 시 대부분 Tier 2나 Tier 3 수준의 배출계수를 적용하고 있 다. 본 연구에서는 국내 교통부문에 사용되는 휘발유, 경유 등의 수송용 연료에 대한 연차별 시계열 특성을 파 악하고, CO2 배출계수의 연도별 변화추이를 분석하여 실제 연료를 활용한 CO2배출계수 실측방법의 적용 타 당성을 평가하였다.

Secondhand smoke (SHS) is one of major public health threats in morbidity and mortality. Several national and regional comprehensive smoke-free regulations have been implemented to prevent public health exposure, but not in Korea. The purpose of this manuscript was to review impacts of the national or regional smoke-free legislations on indoor air quality, health effects and smoking behaviors. Indoor air quality has been improved significantly after smoke free policy. Such improvement was measured by fine particulates and urinary cotinine. Respiratory and cardiovascular health effects were significantly improved after smoke free policy. This is an indirect evidence of association between secondhand smoke exposure and the health effects. Respiratory symptoms were improved as short as one month after smoke free policy. Smoke free policy was also associated with improved perception of danger of secondhand smoke. Reduction of smoking prevalence was also unexpected benefit of smoke free policy. As reviewed in this paper, smoke free policy can be beneficial to indoor air quality, health effects and smoking behaviors. Since Korea does not have comprehensive smoke free policy yet, it is strongly recommended to implement national comprehensive smoke free policy.

Alkaline powder cleaning agents (APCAs) were prepared by blending of Na2CO3 tetrasodium pyrophosphate (TSPP). sodium orthosilicate (Na-OSi), Na-dioctyl sulfosuccinate (303C), Demol C, and MJU-100A (100A). The physical properties of APCAs tested with steel specimen showed the following results. The cleaning powers of APCA-6 (Na2CO3 250g/TSPP 70g/Na-OSi 40g/303C 60g/Demol C 50g/100A 30g mixture) for press-rust preventing oil was 97% and 98% degreasing at 2wt%, 70℃ and 90℃, respectively; for Quenching oil, the cleaning power of APCA-6 was 95% degreasing at 2wt% and 70℃. From the results, it was ascertained that APCA-6 exhibited a good cleaning power. Also low foaming power tests proved that the APCA-6 maintained good defoaming effect.

Two-component polyurethane flame retardant coatings (ATTBC) were prepared by blending polyisocyanate (TDI-adduct) with ATTBs mentioned at the previous paper. Most of the physical properties of the flame retardant coatings were comparable to those of non-flame retardant coatings. Especially, the hardness, impact resistance, and accelerated weathering resistance were remarkably improved with the increase of the content of 1,4-butanediol. Coatings containing 10 and 15 wt% 1,4-butanediol, ATTBC-10C and ATTBC-15C, were not flammable in vertical flame-retardancy test. Their char area recorded 1.1~11.6 cm2 in 45˚ eckel burner method.

A silicone softner (SS-5), a permanent press (PP) finish, was prepared by blending silicone oil KF-96 (as a lubricating component) and beef tallow hardened oil (as a softening component) which was synthesized from fatty polyamide salts. The prepared SS-5 and the PP finishing resin were applied to PP finishing cotton cloth and P/C gingham sample by one-bath method. The properties such as crease recovery, tear strength, and bending resistance were tested. The samples treated with SS-5 and PP finishing resin showed improved properties when comparing with the untreated ones, with the ones treated only with PP finishing resin, with ones treated with commercial PP finishing softners and PP finishing resin. The grades of fabric samples treated with 3% SS-5 were fifth grade in the bending resistance test.

An acrylic resin was synthesized with several monomers, styrene(St), 2-hydroxyethyl methacrylate(2-HEMA), n-butyl acrylate, methyl methacrylate, and acetoacetoxyethl methacrylate(AAEM) to prepare a high-solid coatings. Then, a high-solid acryl/melamine coatings was prepared by curing the acrylic resin with a curing agent, hexamethoxymethylmelamine(HMMM). The curing behavior of the acrylic resin with HMMM was investigated by the Ozawa method using DSC. For AAEM/HMMM and 2-HEMA/HMMM curing reactions, activation energies were 33.01 and 27.12 kcal/mol and frequency factors were 9.54×1015 and 1.53×1013 min-1, respectively. From the results, it was found out that 2-HEMA showed higher reactivity with the curing agent than AAEM.

Two-component polyurethane flame retardant coatings were prepared by blending phosphate-containing modified polyesters(PMPEs) and TDI-adduct. PMPEs were synthesized by polycondensation of dimethyl phenylphosphonate, a flame retardant component, with 1,4-butanediol, adipic acid, and trimethylolpropane. The content of dimethyl phenylphosphonate was varied 10, 15, and 20wt% for the reaction. Various physical properties of these new flame retardant coatings were comparable to non-flame retardant coatings. Coatings with 20wt% dimethyl phenylphosphonate did not burn during the vertical burning test.

Cyclodextrin are obtained from starch by enzymatic degradation. The three best characterize forms are α, β, γ cyclodextrin consisting of 6, 7, and 8 D-glucose units, respectively. Each of the glucose units are in the rigid C1 chair conformation and are linked by α 1,4 bonds. This geometry gives the cyclodextrin the shape of a hollow truncated cone with the wider side formed by the secondary 2- and 3-hydroxy groups and the narrower side by the primary 6-hydroxy group. The most characteristics property of the cyclodextrin is their ability to form inclusion complexes with a wide range of guest moleculars. We syntheses per-6-substituted β-cyclodextrin derivatives and investigate structures, spectrospcopic properties. The substituted materials are piperidine, piperazin, morphorine. The synthetic compound showed a good solubility than natural β cyclodextrin in organic solvents such as methylene chloride, methanol, ethanol, etc.

Durable softening water repellents such as PODCW, PDDCW, and PEDCW were prepared by blending cationized polymers, fatty carbamide, waxes, and emulsifiers. The cationized polymers included poly (octadecyl methacrylate-co-2-diethylaminoethyl methacrylate) [PODC], poly (n-dodecyl methacrylate-co-2-diethylaminoethyl methacrylate) [PDDC]and poly (2-ethylhexyl methacrylate-co-2-diethylaminoethyl methacrylate) [PEDC]. After the PET fabrics were treated with these water repellents, water repellency, softness, and durability of the PET fabrics were examined by various methods : water repellency by the hydrostatic pressure and the contact angle methods, softness by crease recovery and tearing strength, and durability by washability, respectively. Rating of water repellency of PET fabrics treated with PODCW was 80+, but those treated with PDDCW and PEDCW were not high enough to be used in industry.

Durable softening water repellents for nylon fiber were synthesized, using two compounds: quaternized octadecyl methacrylate-2-diethylaminoethyl methacrylate copolymer as a mother resin of water repellent and quaternized fatty carbamide for improving softness and hydrostatic pressure, of which syntheses were studied in the previous papers. They were blended with waxes and emulsifiers in a variety of ratios and synthesized into water repellent PADWC, and it was nylon taffeta treated with and without textile finishing resin. The synthesized water repellents can be used either or without resin. The optimum curing temperature was 150 to 160℃ and the optimum concentration was 3 to 5wt%. In the independent and conjunct treatment, the water repellency of nylon taffeta samples have no remarkable changes between initial value and that after three times washing, so these prove that the synthesized compounds are durable water repellent. The water repellency of PADWC-3 and -4 were around 90. Also, comparison of crease recovery and tear strength after repelling treatment showed that the synthesized water repellents have a very high softening effect.

An experiment was conducted to determine the feeding value of Arundinella hirat silage making by different methods ie., added starch 3%, formic acid 1% (FA), anhydrous ammonia (NH3) 3%, and dried poultry waste (DPW) 3%. The samples were analyzed organi

本 실험은 등과야초인 칡에 당분을 첨가한 사일리지를 조제하여 사료배치를 향상시키기 위하여 실시하였다.칡은 줄기와 잎을 2.0~2.5cm로 절단하여 2l들이 플라스틱 용기에 물8% 첨가한 사일리지, 물8%와 전분3%첨가한 사일리지, 물8%와 포도당3% 첨가한 사일리지 그리고 아무것도 첨가하지 않은 칡 사일리지를 조제하였으며 이들과 옥수수 사일리지를 비교하였다. 사일리지의 발표품질인 유기산과 조직성분의 특성(NOF, AOF, AOL)과 pepsin-cell