이 연구는 20세기 말 이후 중국과 남한의 올림픽 포스터 디자인에서 두드러진 특징과 미묘함을 분석하고 비교합니다. 시각적 표현, 문화적 함 의, 그리고 그들의 사회-역사적 맥락 내의 의사소통 전략을 탐구합니다. 이 연구는 양국이 어떻게 전통적 요소와 현대적 디자인을 독특하게 혼합 하여 국가 정신과 문화적 정체성을 표현하며, 대중의 인식과 감정에 영 향을 주는지를 밝혀냅니다. 또한, 이러한 디자인 뒤에 있는 사회-정치적 동기를 논의하며 미래의 추세를 예상합니다. 이 분석은 중국과 한국의 포스터 디자인의 독특한 가치와 문화 간 의사소통에서의 역할에 대한 새 로운 통찰을 제공합니다.

The challenge of incorporating photothermal conversion function into chitosan (CS) hybrid fibers lies in balancing functionality and mechanical properties. In this study, we successfully prepared a chitosan/graphene oxide/gelatin (CS/GA/GO) hybrid fiber using the wet spinning process, achieving improved mechanical properties and efficient photothermal conversion capabilities. When compared with pure CS fiber with a breaking strength of 1.07 cN/dtex, the breaking strength of the CS/ GA composite fiber increased by 46.73%, while the CS/GA/GO hybrid fiber showed an even greater increase of 85.98%. In addition, the introduction of gelatin (GA) led to secondary scattering of near-infrared light, enhancing the photothermal conversion efficiency. As a result, the CS/GA/GO hybrid fiber exhibited a faster temperature rise rate and higher maximum temperatures (94.3 °C, 103.0 °C, and 111.3 °C) as compared to the CS/GO hybrid fiber. The successful incorporation of GA not only improved the mechanical properties but also enhanced the photothermal performance of the hybrid fiber.

This study successfully prepared high-porosity aluminosilicate fibrous porous ceramics through vacuum suction filtration using aluminosilicate fiber as the primary raw material and glass powder as binder, with the appropriate incorporation of glass fiber. The effects of the composition of raw materials and sintering process on the structure and properties of the material were studied. The results show that when the content of glass powder reached 20 wt% and the samples were sintered at the temperature of 1,000 °C, strong bonds were formed between the binder phase and fibers, resulting in a compressive strength of 0.63 MPa. When the sintering temperatures were increased from 1,000 °C to 1,200, the open porosity of the samples decreased from 89.08 % to 82.38 %, while the linear shrinkage increased from 1.13 % to 10.17 %. Meanwhile, during the sintering process, a large amount of cristobalite and mullite were precipitated from the aluminosilicate fibers, which reduced the performance of the aluminosilicate fibers and hindered the comprehensive improvement in sample performance. Based on these conditions, after adding 30 wt% glass fiber and being sintered at 1,000 °C, the sample exhibited higher compressive strength (1.34 MPa), higher open porosity (89.13 %), and lower linear shrinkage (5.26 %). The aluminosilicate fibrous porous ceramic samples exhibited excellent permeability performance due to their high porosity and interconnected three-dimensional pore structures. When the samples were filtered at a flow rate of 150 mL/min, the measured pressure drop and permeability were 0.56 KPa and 0.77 × 10-6 m2 respectively.

In this work, the trend in the performance of carbon fiber (CF) and its composite during self-polymerization of polydopamine (PDA) at carbon fiber surface was investigated by varying the self-polymerization time of dopamine in an aqueous solution. Research has shown that the PDA coating elevated the surface roughness and polarity of the inert fiber. The tensile strength of single carbon fiber was significantly improved, especially after 9 h of polydopamine self-polymerization, increasing by 18.64% compared with that of desized carbon fiber. Moreover, the interlaminar shear strength (ILSS) of CF-PDA9-based composites was 35.06% higher than that of desized CF-based composites. This research will provide a deep insight into the thickness and activated ingredients of dopamine oxidation and self-polymerization on interfacial compatibility of carbon fiber/epoxy resin composites.

Modification of the surface of raw activated carbon using chemical solvents can significantly improve the adsorption performance of activated carbon. Triethylenetetramine is one of the most important chemical solvents used to modify raw activated carbon for formaldehyde removal indoor. We conducted the liquid impregnation experiments at different initial concentrations, temperatures, adsorbent dosage and time ranges to fully investigate the adsorption of triethylenetetramine on the surface of raw activated carbon for modification. We found that the Langmuir isotherm model and pseudo-first-order kinetic model fit quite well with the experimental data and the R2 are 0.9883 and 0.9954, respectively. The theoretical maximum adsorption capacity is 166.67 mg/g. The change in Gibbs free energy (ΔG0), enthalpy change (ΔH0) and entropy change (ΔS0) were also calculated to study the direction and driving force of the liquid adsorption process. In order to understand the adsorption process at the molecular level, a new activated carbon model based on the actual physical and chemical properties of activated carbon was carefully established in the Materials Studio to simulate the liquid-phase adsorption. The pore structure, elemental composition, functional group content, density, pore volume, and porosity of the activated carbon model converge close to the actual activated carbon and the adsorption isotherms obtained from the simulation agree well with the experimental results. The results show that the adsorption of triethylenetetramine on activated carbon is a spontaneous, endothermic and monolayer physical adsorption process.

Natural enemy insects, including predators and parasitoids, are beneficial organisms that feed upon other agricultural pests. Using natural enemy insects to suppress or prevent outbreak of pests is a key component of integrated pest management strategy. It is safe, effective, and environmentally friendly and can be applied easily to the greenhouses, filed crops and orchards. Rearing and application of natural enemy insects in biocontrol in China have a long history. As early as 1700 years ago, the predator Oecophylla smaragdina has been used for controlling many kinds of citrus pests. Up to now, more than 30 species of natural enemies that can be artificially mass produced and widely used for biological control of many kinds of pests, including caterpillars, aphids, whiteflies, thrips, leaf mites and scales in China. The annual average application area of natural enemies is over 11.34 million hectares. However, with the increasing demand of using natural enemies in biological control programs, the development of natural enemy insect industrialization still face many challenges. It is urgent to explore more effective candidate natural enemies, improve the production efficiency, increase the shelf life of products and enhance the colonization of natural enemy insects after release, and thus facilitate the commercially production and application of natural enemies. This is of great significance for comprehensively promoting the use of green prevention and control techniques for crop diseases and pests, reducing the use of chemical pesticides, ensuing the quality and safety of food and agricultural products, and ultimately promoting sustainable agricultural development.

Some digital platforms introduced a novel positive-framing design in the multi-dimensional rating system, which framed the attribute with positive words for consumers to rate. The results from a cross-platform quasi-natural experiment show that the positive-framing design can increase the rating scores compared with the traditional non-positive framing design.

Graphitic carbon nitride (g-C3N4) has attracted extensive attention in energy storage due to its suitable and tunable bandgap, high chemical/thermal stability, earth abundance and environmental friendliness. However, its conductivity should be improved to work as the electrode materials in supercapacitors. In this report, we have prepared a two-dimensional composite (CN-PANI) based on g-C3N4 and polyaniline (PANI) by in-situ polymerization, which can be efficiently applied as electrode material for supercapacitors. The introduction of PANI can increase the conductivity of the electrode, and the porous structure of g-C3N4 can provide enough channels for the transport of electrolyte ions and improve the electrode stability. As a result, the obtained CN-PANI demonstrates excellent specific capacitance (234.0 F g− 1 at 5 mV/s), good rate performance and high cycling stability (86.2% after 10,000 cycles at 50 mV/s), showing great potential for high-rate supercapacitors.

지능형 컴퓨팅의 등장으로 빅데이터를 활용한 패션 브랜드 의미 마이닝과 가치 홍보에 초점을 맞춘 새로운 연구 트렌드가 등장하였다. 본 연구의 목적은 인기 여성복 브랜드 5개를 대상으로 다양한 종류의 의류에 대한 소비자 감성 트렌드를 조사하는 것이다. 유니클로, 에이치스타일, 베로모다, 피스버드, 온리. 이를 위해 총 93,550건의 소비자 평가를 수집하고, 키스멧 감성 분석 엔진을 활용하여 의류 유형별 감성 극성도를 분석하였 다. 그 결과, 브랜드에 따라 감정 극성이 크게 다르다는 것을 알 수 있었으며, HSTYLE 후드티, ONLY 니트웨 어, 피스버드 순면, 유니클로 니트가 각각 소비자들에게 가장 강한 긍정적 감정을 불러일으켰다. 또한 이번 연 구에서는 각 브랜드에서 가장 인기 있는 의류 유형과 착용 효과를 밝혀 패션 기업이 효과적인 마케팅 전략을 수립하고 제품 제공을 강화하는 데 중요한 인사이트를 제공했다. 이러한 연구 결과를 바탕으로 게임 업계에서 는 감성 분석을 적용하여 다양한 게임 브랜드, 장르, 게임 플레이에 대한 플레이어의 감정 반응을 이해하고 게임 프로모션 전략과 제품 디자인 개발에 도움을 줄 수 있다. 전반적으로 이 연구 결과는 디자인 분야에서 빅데이터의 잠재력을 입증하고 업계에서 경쟁 우위를 확보하기 위해 빅데이터를 활용하는 것이 중요하다는 점을 강조할 수 있다.

In this study, nitric acid oxidation with varied treatment temperature and time was conducted on the surfaces of polyacrylonitrile- based ultrahigh modulus carbon fibers. Scanning electron microscopy, X-ray photoelectron spectroscopy, Raman spectroscopy and surface tension/dynamic contact angle instruments were used to investigate changes in surface topography and chemical functionality before and after surface treatment. Results showed that the nitric acid oxidation of ultrahigh modulus carbon fibers resulted in decreases in the values of the crystallite thickness Lc and graphitization degree. Meanwhile, increased treating temperature and time made the decreases more obviously. The surfaces of ultrahigh modulus carbon fibers became much more activity and functionality after surface oxidation, e.g., the total surface energy of oxidized samples at 80 °C for 1 h increased by 27.7% compared with untreated fibers. Effects of surface nitric acid oxidation on the mechanical properties of ultrahigh modulus carbon fibers and its reinforced epoxy composites were also researched. Significant decreases happened to the tensile modulus of fibers due to decreased Lc value after the nitric acid oxidation. However, surface treatment had little effect on the tensile strength even as the treating temperature and processing time increased. The highest interfacial shear strength of ultrahigh modulus carbon fibers/epoxy composites increased by 25.7% after the nitric acid oxidation. In the final, surface oxidative mechanism of ultrahigh modulus carbon fibers in the nitric acid oxidation was studied. Different trends of the tensile strength and tensile modulus of fibers in the nitric acid oxidation resulted from the typical skin–core structure.

The 1982 United Nations Convention on the Law of the Sea admitted legislation and enforcement jurisdiction carried out by the flag state. However, the emergence of substandard ships and the growing number of ship accidents at sea indicate that flag state jurisdiction is far from effective. Four aspects of these failures are examined in this paper. Confronted with the failure of flag state jurisdiction, port states have devised a subsidiary remedy to ensure their national interests and restore the effectiveness of flag state jurisdiction. A problem hereunder arises because non-explicit permission was given to port states to prosecute substandard ships. Thus, this paper further analyses four aspects of port state jurisdiction. The authors aim to analyse the failures and remedies associated with state jurisdiction over ships. It reviews the scope and deficiency of state jurisdiction in combatting substandard ships and illicit activities at sea. This paper also addresses the importance of port state control, regional memorandums of understanding and international conventions.

Liquefied gas carrier cargo handling operations are critical to ship safety. In order to improve the quality and efficiency of cargo handling of liquefied gas carriers, the loading and unloading operation of the liquefied gas carrier was studied and a set of LPG remote cargo operation simulator with automatic bargaining function was designed. Introducing the components of the simulator: the console unit and the simulated cargo tank unit in brief, the design ideas and specific functions of the automatic barge and remote control of the core part of the system are introduced in detail. The simulator feasibility verification is carried out by comparing the error between the actual loading and unloading operation with the system simulation loading and unloading operation. The simulation training functions verification is carried out by testing people who use the simulator for training. The final results show that the error is within the acceptable range, and people who use the simulator for training can pass an authoritative comprehensive exam. It is shown that that the system can simulate the important operations in the cargo handling process and has an excellent training effect.

The KVN(Korean VLBI Network)-style simultaneous multi-frequency receiving mode is demonstrated to be promising for mm-VLBI observations. Recently, other Very long baseline interferometry (VLBI) facilities all over the globe start to implement compatible optics systems. Simultaneous dual/multi-frequency VLBI observations at mm wavelengths with international baselines are thus possible. In this paper, we present the results from the first successful simultaneous 22/43 GHz dualfrequency observation with KaVA(KVN and VERA array), including images and astrometric results. Our analysis shows that the newly implemented simultaneous receiving system has brought a significant extension of the coherence time of the 43 GHz visibility phases along the international baselines. The astrometric results obtained with KaVA are consistent with those obtained with the independent analysis of the KVN data. Our results thus confirm the good performance of the simultaneous receiving systems for the non-KVN stations. Future simultaneous observations with more global stations bring even higher sensitivity and micro-arcsecond level astrometric measurements of the targets.

Nowadays, customers have become increasingly dissatisfied with accepting products and services offered by suppliers. Instead, they are involved in product development as co-productor (Prahalad & Ramaswamy, 2004). There are diverse types ranging from online discussion to virtual design enabling customer involved in co-creation activities related to product support. “Customer design” enables the firm to have possibilities enhancing the whole value of product design during development process (Fuchs & Schreier, 2011). However, some of scholars have found that customers cannot always play a useful role in luxury product design. Fuchs and Schreier (2011) studied that buyers can easily observe the source of design, which damage the image of co-designed product. That is because luxury product always played as a specific label of wealth and states to some extend (Ko & Phau, Aiello, 2016). Thus, this study draws from co-creation theory to investigate the specificity of online luxury design, using an experimental method. We analyze and discuss the diverging affection of luxury design held by co-creation idea innovativeness and behavior intensity, and the role played by sponsoring firm and community members.

Products are successfully designed only when they are in accord with the users’ emotional needs. A systematic research approach is aimed to propose that physiological metrics can be effectively used to assess user emotion and behavior intention based on an eye tracker and neurophysiological approach. Forty participants (20 males and 20 females, mean age=35.6, SD=6.38, range 21-48 years), were recruited from college campuses and communities to conduct an eye tracker and electroencephalography (EEG) experiment with the presented stimuli (images of SUVs). The study uses partial least squares structural equation modeling (PLS-SEM) to test the model hypotheses. The results show a strong and significant relationship between eye tracker metrics, neurophysiological metrics, user affective responses, and behavior intention. These findings could enable industrial counselors, professional product designers, and academics to categorize users’ emotional needs that can be subsequently incorporated into final product design.

The warm recycling technology has been increasingly used in many countries due to the environmental and financial benefits. In this study, the rheological and fatigue performance evolutions of warm-mix recycled asphalt materials during the secondary service period were evaluated in two scales, mixture and fine aggregate matrix (FAM). A laboratory simulation method was proposed to produce warm-mix recycled asphalt binders with various long-term aging levels for the mixture and FAM tests. The dynamic shear rheometer temperature and frequency sweep test and time sweep test were conducted to characterize the rheological and fatigue behavior of FAMs, respectively. The rheological and fatigue properties of asphalt mixtures were measured by the dynamic modulus test and semi-circular bending test, respectively. Effects of aging levels and recycling plans on different pavement performance were investigated. Performance correlations between the mixture and FAM were finally investigated by the statistical method. It is found that the secondary long-term aging causes the continuous increase in the stiffness and decrease in the viscoelasticity level in each material scale, indicating the improvement of the rutting resistance and the reduction of the fatigue resistance. The warm mix asphalt technology plays a positive role in the fatigue performance with a loss of the rutting resistance. Using the styrene butadiene rubber latex can improve different pavement performance within the whole time-temperature domain. Good performance correlations between the mixture and FAM are developed, indicating that the FAM may be the critical material scale for evaluating the rheological and fatigue performance of warm-mix recycled asphalt pavements.

The service life of coal gangue concrete(CGC) strongly depends on the capillary water absorption, this water absorption is susceptible to freeze-thaw cycles. In this paper, the cumulative water absorption and sorptivity were obtained to study the effects of 0, 0.5, 1.0, and 1.5 % steel fiber volume fraction added on the water absorption of CGC. Sorptivity and freeze-thaw tests were conducted, and the capillary water absorption was evaluated by the rate of water absorption(sorptivity). Three prediction models for the initial sorptivity of steel fiber reinforced coal gangue concrete(SFRCGC) under freeze-thaw cycles were established to evaluate the capillary water absorption of SFRCGC. Results showed that, without freeze-thaw cycles, the water absorption of CGC decreased when steel fiber at 1.0 % volume fraction was added, however, the water absorption increased with the addition of 0.5 or 1.5% steel fibers. Once the SFRCGC specimens were exposed to freeze-thaw cycles, the water absorption of SFRCGC significantly increased, and 1.0 % steel fiber in volume fraction added to CGC caused the lowest water absorption, except for the case of the sample without steel fibers added. The CGC with steel fiber at 1.0 % volume fraction performed better. The SFRCGC has a strong response to freeze-thaw cycles. Results also showed that the linear function prediction model is practical in the field of engineering because of its simple form and a relatively high precision. Although the polynomial prediction model presents the highest computation precision among the three models, the complicated form and too many coefficients make it impractical for engineering applications.

A robust adaptive control approach is proposed for underactuated surface ship linear path-tracking control system based on the backstepping control method and Lyapunov stability theory. By employing T-S fuzzy system to approximate nonlinear uncertainties of the control system, the proposed scheme is developed by combining “dynamic surface control” (DSC) and “minimal learning parameter” (MLP) techniques. The substantial problems of “explosion of complexity” and “dimension curse” existed in the traditional backstepping technique are circumvented, and it is convenient to implement in applications. In addition, an auxiliary system is developed to deal with the effect of input saturation constraints. The control algorithm avoids the singularity problem of controller and guarantees the stability of the closed-loop system. The tracking error converges to an arbitrarily small neighborhood. Finally, MATLAB simulation results are given from an application case of Dalian Maritime University training ship to demonstrate the effectiveness of the proposed scheme.